PP338PT
Table of contents
Loading...
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1--800--554--6723
www.poulan--pro.com
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
For Occasional Use Only
R
ENGLISH ESPAÑOL
PP338PT
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury .
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones graves.
AVERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertissements et toutes les instructions de sécurité. T out défaut de le
faire pourrait entraîner des blessures graves.
Poulan PRO
7349 Statesville Road
Charlotte, NC 28269
850 Matheson Blvd. West
Mississauga, Ontario L5V 0B4
115224926 Rev. 1 9/15/09 BRW
Poulan PRO
FRANÇAIS
IDENTIFICATION OF SAFETY SYMBOLS
DANGER: To prevent electrocution, do
not use near electrical wires or power lines. Keep
pruner at least 30 feet (10 meters) away from all
power lines.
DANGER: Falling objects can cause severe
head injury. Wear head protection when operating
this unit. Do not stand beneath branch being cut.
DANGER: Use only specified trimmer
head, spool, and 0.080 inch (2 mm) recommended
trimmer line. Never use blades, flailing devices,
wire, rope, string, etc. This attachment is designed
for line trimmer use only. Failure to follow these
instructions may result in serious injury.
WARNING: Avoid kickback which can result in serious injury. Kickback is the back-
ward, upward or sudden forward motion of the guide bar occurring when the chain near the
upper tip of the guide bar contacts any object such as a log or branch, or when the wood
closes in and pinches the chain in the cut. Contacting a foreign object in the wood can also
result in loss of control.
WARNING: Do not operate pruner from a ladder
or unstable support. Always cut with both feet on solid
ground to prevent being pulled off balance.
WARNING: This unit can be dangerous! Careless or improper
use can cause serious injury.
Read the operator’s manual before use. Failure to follow instructions
could result in serious injury. Save operator’s manual.
2
IDENTIFICATION OF SAFETY SYMBOLS
Trimmer line can throw objects violently. You can be blinded or injured. Wear protective
gear. Always use steel-toed safety footwear with non-slip soles; snug-fitting clothing;
heavy, long pants, and long sleeves; heavy-duty, non-slip gloves; eye protection marked
Z87 such as non-fogging, vented goggles or face screen; an approved safety hard hat; and
sound barriers (ear plugs or mufflers) to protect your hearing. Regular users should have
hearing checked regularly as engine noise can damage hearing. Always use shoulder
strap when operating unit.
Secure hair above shoulder length. Do
not wear jewelry, loose clothing, or
clothing with loosely hanging straps,
ties, tassels, etc. They can be caught in
moving parts.
Hazard zone. Keep children, bystanders, and animals
a minimum of 50 feet (15 meters) away from the work
area. Do not allow other people or animals to be near
when starting or operating the pruner.
Hazard zone for thrown objects.
S Trimmer line throws objects violently.
S Y ou and others can be blinded/injured.
S Keep children, bystanders, and animals 50 feet
(15 meters) away.
Carefully plan your pruning operation in advance. Do not
start cutting until you have a clear work area, secure
footing, and a planned retreat path.
Do not operate a pruner with one hand. Serious injury to the
operator, helpers, bystanders or any combination of these
persons may result from one-handed operation. A pruner is
intended for two-handed use.
3
IDENTIFICATION OF SAFETY SYMBOLS
Assist handle to be positioned only below
the arrow.
Never allow children to operate this unit.
Store unit indoors in a high, dry place out of the reach of
children.
When servicing unit, use only identical replacement
parts.
Always stop unit and disconnect spark plug before cleaning or servicing.
WARNING: Fire hazard. Never mix, pour, or store gasoline or
use the unit near a flame or sparks (including smoking, open flames, or
work that can cause sparks).
Use unleaded gasoline and two--stroke oil mixed at a ratio of
40:1 (2.5%).
4
SAFETY RULES
WARNING: Always disconnect spark
plug wire and place wire where it cannot contact
spark plug to prevent accidental starting when
setting up, transporting, adjusting or making repairs except carburetor adjustments.
Because a pruner is a high-speed wood-cutting
tool, special safety precautions must be observed to reduce the risk of accidents. Careless
or improper use of this tool can cause serious or
even fatal injury.
PLAN AHEAD
S Read this manual carefully until you
completely understand and can follow all
safety rules, precautions, and operating
instructions before attempting to use the unit.
S Restrict the use of your pruner to adult users
who understand and can follow safety rules,
precautions, and operating instructions found
on the unit and in this manual.
INSTRUCTION
MANUAL
PRUNER SAFETY
S Keep all parts of your body away from the
chain when the engine is running.
S Do not handle or operate a pruner when you
are fatigued, ill, or upset, or if you have taken
alcohol, drugs, or medication. You must be in
good physical condition and mentally alert. If
you have any condition that might be
aggravated by strenuous work, check with
doctor before operating a pruner.
S Operate pruner only in a well-ventilated
outdoor area.
S Do notuse apruner to cut down trees orany
portion of the tree trunk.
S Only use for pruning limbs or branches
overhead not greater than 6 inches (15 cm)
in diameter.
S Do notcut small brush and saplings with the
pruner. Slender matter may catch in the
chain and be whipped toward you, pulling
you off balance.
S Make sure the chain will not make contact
with any object while starting the engine.
Never try to start the unit when the guide
bar is in a cut.
S Do notput pressure onthe pruner at the end
of the cut. Applying pressure can cause you
to lose control when the cut is completed.
S Do not run the unit at high speed when not
pruning.
S If you strike or become entangled with a
foreign object, stop the engine immediately
and check for damage. Have any damage
repaired by an authorized service dealer
before attempting further operations.
S Do not operate a pruner that is damaged,
improperly adjusted, or not completely and
securely assembled. Always replace bar
and chain immediately if it becomes
damaged, broken or is otherwise removed.
SAFETY INFORMATION
ON THE UNIT
S Always stop the unit when work is delayed
or when walking from one cutting location to
another. Stop the engine before setting the
unit down.
S Use only in daylight or good artificial light.
S Use only for jobs explained in this manual
(or manuals for optional attachments).
LINE TRIMMER SAFETY
WARNING: Inspect the area to be
trimmed before each use. Remove objects
(rocks, broken glass, nails, wire, etc.) which
can be thrown by or become entangled in line.
Hard objects can damage the trimmer head
and be thrown causing serious injury.
S Keep children, bystanders, and animals 50
feet (15 meters) away. Bystanders should be
encouraged to wear safety glasses. Stop
unit immediately if approached.
S Dress properly. Always wear safety
glasses or similar eye protection when
operating, or performing maintenance, on
your unit (safety glasses are available).
Eye protection should be marked Z87.
S Always wear face or dust mask if operation
is dusty.
S Always wear heavy, long pants, long
sleeves, boots, and gloves. Wearing safety
leg guards is recommended.
S Always wear foot protection. Do not go
barefoot or wear sandals. Stay clear of
spinning line.
S Secure hair above shoulder length. Secure
or remove loose clothing or clothing with
loosely hanging ties, straps, tassels, etc.
They can be caught in moving parts.
S Being fully covered also helps protect you
from debris and pieces of toxic plants
thrown by spinning line.
S Stay alert. Do not operate this unit when you
are tired, ill, upset or under the influence of
alcohol, drugs, or medication. Watch what
you are doing; use common sense.
S Wear hearing protection.
S Never start or run inside a closed room or
building. Breathing exhaust fumes can kill.
S Keep handles free of oil and fuel.
S Always keep engine on the right hand side
of your body.
S Hold the unit firmly with both hands.
S Keep trimmer head (or other optional
attachment) below waist level and away
from all parts of your body. Do not raise
engine above your waist.
S Keep all parts of your body away from
muffler and spinning line (or other optional
attachment). Keep engine below waist
level. A hot muffler can cause serious
burns.
S Keep firm footing and balance. Do not
overreach or use from unstable surfaces
such as ladders, trees, steep slopes,
rooftops, etc.
S Use only in daylight or good artificial light.
S Use only for jobs explained in this manual
(or manuals for optional attachments).
5
MAINTAIN YOUR UNIT IN GOOD
WORKING ORDER
WARNING: Disconnect the spark
plug before performing maintenance except
carburetor adjustments.
S Look for and replace damaged or loose
parts before each use. Look for and repair
fuel leaks before use. Keep in good working
condition.
S Make certain the chain stops moving when
the throttle trigger is released. For
correction, refer to CARBURETOR
ADJUSTMENTS.
S Replace trimmer head parts that are
chipped, cracked, broken, or damaged in
any other way before using the unit.
S Never modify your unit in any way.
S Keep the handles dry, clean, and free of oil
or fuel mixture.
S Keep fuel and oil caps, screws, and
fasteners securely tightened.
S Maintain unit according to recommended
procedures. Keep cutting line at proper
length.
S Use only 0.080″ (2 mm) diameter Poulan
PRO brand line. Never use wire, rope, string,
etc.
S Install required shield properly before using
the unit. Use only specified trimmer head;
make sure it is properly installed and
securely fastened.
S Make sure unit is assembled correctly as
shown in this manual.
S Make carburetor adjustments with lower
end supported to prevent line from
contacting any object.
S Keep others away when making carburetor
adjustments.
S Use only recommended Poulan PRO
accessories and replacement parts.
S Have all service performed by a qualified
service dealer with the exception of the
items listed in the maintenance section of
this manual.
HANDLE FU EL WITH CA UT ION
S Do not smoke while handling fuel or while
operating the unit.
S Eliminate all sources of sparks or flame in
the areas where fuel is mixed or poured.
There should be no smoking, open flames,
or work that could cause sparks. Allow
engine to cool before refueling.
S Mix and pour fuel in an outdoor area on bare
ground; store fuel in a cool, dry, well
ventilated place; and use an approved,
marked container for all fuel purposes.
Wipe up allfuel spills before starting engine.
S Move at least 10feet (3 meters) from fueling
site before starting engine.
S Turn the engine off and let unit cool in a
non-combustible area, not on dry leaves,
straw, paper, etc. Slowly remove fuel cap
and refuel unit.
S Store the unit and fuel in an area where fuel
vapors cannot reach sparks or open flames
from water heaters, electric motors or
switches, furnaces, etc.
S Stop engine and allow to cool before
removing fuel cap.
S Always store gasoline in a container
approved for flammable liquids.
KICKBACK
WARNING: Avoid kickback which
can result in serious injury. Kickback is the
backward, upward or sudden forward motion
of the guide bar occurring when the chain
near the upper tip of the guide bar contacts
any object such as a log or branch, or when
the wood closes in and pinches the chain in
the cut. Contacting a foreign object in the
wood can also result in loss of control.
S Rotational Kickback can occur when the
moving chain contacts an object at the upper
tip of the guide bar. This contact can cause
the chain to dig into the object, which stops
the chain for an instant. The result is a
lightning fast, reverse reaction which kicks the
guide bar up and back toward the operator.
S Pinch-Kickback can occur when the wood
closes in and pinches the moving chain in
the cut along the top of the guide bar and the
chain is suddenly stopped. This sudden
stopping of the chain results in a reversal of
the chain force used to cut wood and
causes the pruner to move in the opposite
direction of the chain rotation. The pruner is
driven straight back toward the operator.
S Pull-In can occur when the moving chain
contacts a foreign object in the wood in the cut
along the bottom of the guide bar and the
chain is suddenly stopped. This sudden
stopping pulls the pruner forward and away
from the operator and could easily cause the
operator to lose control of the pruner.
REDUCE THE CHANCE OF
KICKBACK
S Recognize that kickback can happen. With
a basic understanding of kickback, you can
reduce the element of surprise which
contributes to accidents.
S Never let the moving chain contact any
object at the tip of the guide bar.
S Keep the working area free from
obstructions such as other trees, branches,
rocks, stumps, etc. Eliminate or avoid any
obstruction that your chain could hit while
you are cutting. When cutting a branch, do
not let the guide bar contact branch or other
objects around it.
S Keep your chain sharp and properly
tensioned. A loose or dull chain can
increase the chance of kickback occurring.
Follow manufacturer’s chain sharpening
and maintenance instructions. Check
tension at regular intervals with the engine
stopped, never with the engine running.
Make sure the bar clamp nut is securely
tightened after tensioning the chain.
S Begin and continue cutting at full speed. If
the chain is moving at a slower speed, there
is greater chance of kickback occurring.
S Cut one branch at a time.
S Use extreme caution when re-entering a
previous cut.
6
S Do not attempt cuts starting with the tip of
the bar (plunge cuts).
S Watch for shifting of wood or other forces that
could close a cut and pinch or fall into chain.
S Use the Reduced- -Kickback Guide Bar and
Low- -Kickback Chain specified for your unit.
MAINTAIN CONTROL
S Keep a good, firm grip on the pruner with
both hands when the engine is running and
don’t let go. A firm grip will help you reduce
kickback and maintain control. Keep the
fingers of your left hand encircling and your
left thumb under the assist handle. Keep
your right hand completely around the
throttle handle whether your are right
handed or left handed.
S Stand with your weight evenly balanced on
both feet.
S Stand slightly to the left side of the pruner to
keep your body from being in a direct line
with the cutting chain.
KICKBACK SAFETY FEATURES
The following features are included on your
pruner to help reduce the hazard of kickback;
however, such features will not totally eliminate
this danger. As a pruner user, do not rely only
on safety devices. Yo u must follow all safety
precautions, instructions, and maintenance in
this manual to help avoid kickback and other
forces which can result in serious injury.
S Reduced--Kickback Guide Bar, designed
with a small radius tip which reduces the
size of the kickback danger zone on the bar
tip.
Reduced Kickback Symmetrical Guide Bar
Small Radius Tip
Symmetrical Guide Bar
S Low--Kickback Chain, designed with a
contoured depth gauge and guard link
Large Radius Tip
which deflect kickback force and allow
wood to gradually ride into the cutter.
Low---K ickback
Not a Low---Kickback Chain
WARNING: The engine exhaust
from this product contains chemicals known
to the State of California to cause cancer, birth
defects or other reproductive harm.
SAFETY NOTICE:Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or abnormal swellings. Prolonged use in cold
weather has been linked to blood vessel damage in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek medical attention. An anti--vibration system does
not guarantee the avoidance of these problems. Users who operate power tools on a
continual and regular basis must monitor
closely their physical condition and the condition of this tool.
SPECIAL NOTICE: This unit is equipped
with a temperature limiting muffler and spark
arresting screen which meets the requirements of California Codes 4442 and 4443. All
U.S. forest land and the states of California,
Idaho, Maine, Minnesota, New Jersey, Oregon, and Washington require by law that
many internal combustion engines be
equipped with a spark arresting screen. If you
operate in a locale where such regulations exist, you are legally responsible for maintaining
the operating condition of these parts. Failure
to do so is a violation of the law. For normal
homeowner use, the muffler and spark arresting screen will not require any service. After
50 hours of use, we recommend that your
muffler be serviced or replaced by an authorized service dealer.
Contoured De pth Gauge
Chain
Elongate d Guard Link
Deflects
kickback force
and allows wood
to gradually ride
into cutter
Can Obstruct Material
ADDITIONAL SAFETY RULES
FOR OPTIONAL ATTACHMENTS
WARNING: For each optional at-
tachment used, read entire instruction manual before use and follow all warnings and instructions in manual and on attachment.
WARNING: Ensure handlebar is
installed when using brushcutter attachment.
Attach handlebar above arrow on safety label
on the upper shaft (engine end of unit). If your
brushcutter attachment does not include a
7
handlebar, a handlebar accessory kit
(#530071451) is available from your authorized service dealer.
Handlebar
EDGER SAFETY
WARNING: Inspect the area to be
edged before each use. Remove objects
(rocks, broken glass, nails, wire, etc.) which
can be thrown by the blade or can wrap
around the shaft.
WARNING: Blade rotates momen-
tarily after the trigger is released or engine is
turned off. The blade can seriously cut you or
others. Allow blade to stop before removing it
from the cut.
S Throw away blades that are bent, warped,
cracked, broken or damaged in any other
way. Replace parts that are cracked,
chipped, or damaged before using the unit.
S Do not attempt to remove cut material nor
hold material to be cut when the engine is
running or when cutting blade is moving.
S Always keep the wheel and depth adjusting
skid in contact with the ground.
S Always push the unit slowly over the
ground. Stay alert for uneven sidewalks,
holes in the terrain, large roots, etc.
BLOWER/VACUUM SAFETY
WARNING: Inspect area before
starting unit. Remove all debris and hard objects such as rocks, glass, wire, etc. that can
ricochet, be thrown, or otherwise cause injury
or damage during operation.
S Do not set unit on any surface except a
clean, hard area while engine is running.
Debris such as gravel, sand, dust, grass,
etc., could be picked up by the air intake
and thrown out through discharge opening,
damaging unit, property, or causing serious
injury to bystanders or operator.
S Never place objects inside the blower tubes,
vacuum tubes or blower outlet. Always direct
the blowing debris away from people, animals, glass, and solid objects such as trees,
automobiles, walls, etc. The force of air can
cause rocks, dirt, or sticks to be thrown or to
ricochet which can hurt people or animals,
break glass, or cause other damage.
S Never run unit without the proper equip-
ment attached. When using your unit as a
blower, always install blower tubes.
S Check air intake opening, blower tubes or
vacuum tubes frequently, always with engine stopped and spark plug disconnected.
Keep vents and discharge tubes free of debris which can accumulate and restrict
proper air flow.
S Never place any object inair intake opening
as this could restrict proper air flow and
cause damage to the unit.
S Never use for spreading chemicals, fertiliz-
ers, orother substances which may contain
toxic materials.
S Toavoid spreading fire, do not use near leaf
or brush fires, fireplaces, barbecue pits,
ashtrays, etc.
BRUSHCUTTER SAFETY
DANGER: Blade can thrust violently
away from material it does not cut. Blade
thrust can cause amputation of arms or legs.
WARNING: Do not use trimmer head
as a fastening device for the blade.
WARNING: The blade continues to
spin after the trigger is released or engine is
turned off. The coasting blade can throw objects or seriously cut you if accidentally
touched. Stop the blade by contacting the
right hand side of the coasting blade with material already cut.
WARNING: Inspect the area to be
cut before each use. Remove objects (rocks,
broken glass, nails, wire, etc.) which can be
thrown or become entangled in the blade or
trimmer line.
8
Loading...