5 Easy Steps
The fastest way to set up your Plantronics Voyager™ 510S Office Headset System with your desk phone and Bluetooth® mobile phone
Base Power
Adapter
HL10
Automatic
Handset Lifter*
Voyager 510S
Headset
Voyager 510S
Headset Base
*Not included in all configurations
Plantronics Voyager 510S Se t u p Gu i d e
Plantronics Voyager 510S Package Contents
5 Easy Steps
The fastest way to set up your
Voyager 510S Office Headset System with your desk phone and Bluetooth mobile phone
Eartips
Headset |
Setup Guide |
Headset Base with Pre- |
|
|
installed Phone Cable |
Headset Travel Charger
Base Power Adapter
Please refer to the separate Safety Instructions for important product safety information prior to installation or use of the product.
Voyager 510SL With Automatic Handset Lifter* Adds:
HL10 Additional Parts Kit (if needed)
HL10 Automatic |
HL10 |
|
Handset Lifter |
||
User Guide |
||
|
Extender |
Ringer |
Adapter for |
Arm |
Microphone |
Nortel i2004 |
|
|
Phones |
*Automatic Handset Lifter is bundled with certain Voyager 510S configurations and also available separately.
Voyager 510SL+ Adds:
Online |
Car |
USB |
Belt Clip |
Indicator |
Lighter |
Headset |
Carry Pouch |
Light |
Adapter |
Charger |
|
Accessories are available separately.
Plantronics Voyager 510S Setup Guide
ST1 |
|
PE |
Install Eartip & Adjust fit |
Fit the Headset
Slide the headset over and behind your ear, then press gently toward your ear. Rotate the microphone boom until it is pointed toward your mouth. If the eartip is uncomfortable, install a different eartip. See below.
For your safety and comfort, the eartip should never be inserted into the ear canal.
To Install a Different Eartip
Remove the pre-installed eartip by pushing in and turning the eartip clockwise, then pull firmly.
Choose the size and style of |
Push in firmly and |
||
eartip that fits most comfort- |
twist counter |
||
ably. Align eartip tabs with |
clockwise. |
||
notches in headset. |
|
|
|
|
|
|
|
|
|
|
|
Note: For gel tips, ensure the raised part of the eartip is pointed towards the curved section of the headset as shown..
To Convert for Wearing on Left Ear
A. Rotate microphone |
B. Turn microphone |
C. Rotate microphone |
boom up |
boom around |
boom down |
Questions? For fast, efficient Technical Support call: 800-544-4660 Ext. 5538
S T E P
2Connect Base to Desk Phone
It is important for correct and safe operation that the base cord is installed into the proper jack of your telephone. Follow these instructions carefully, especially if your telephone has two jacks where
the handset was attached. Be sure to note or mark which jack was used for the handset.
Use Configuration A if:
You will use the Automatic Handset Lifter or…
Your phone does NOT have built-in headset functionality (no Headset button).
Configuration A
1. Unplug the handset coil cord from the desk phone handset port [A], then plug it
into the handset port [B] on the Headset Base.
A
Handset |
Handset |
Coil Cord |
|
Headset Base (bottom view)
A B
2. Plug the short black Phone Cable that is pre-installed on the Headset Base into the now-open handset port [A] on the desk phone.
Plantronics Voyager 510S Setup Guide
Use Configuration B if:
You will NOT use the Automatic Handset Lifter and…
Your phone has built-in headset functionality (a Headset button).
Configuration B
Confirm there is
a “Headset” button on your phone
Headset Base (bottom view)
C
1. Plug the short BLACK Phone Cable that is pre-installed on the Headset Base into the Headset port [C] on the desk phone.
Handset port or Headset port?
You should only use the headset port if you will not be using the Automatic Handset Lifter and you have a pre-programmed Headset button on your phone.
In this configuration you must press both the Headset button on your phone and the Call Control Button on the headset to answer/end calls.
Questions? For fast, efficient Technical Support call: 800-544-4660 Ext. 5538
S T E P
3Connect Power and Charge Headset
A. Connect Headset Base to power outlet
1. Plug the Base Power Adapter into a wall outlet, then plug the power cord into the yellow labeled connector on the bottom of the Headset Base. The red Power light on the left front of the Headset Base will turn on. (See illustration at bottom of page.)
Insert into yellow labeled power connection on Headset Base as shown to charge.
Base
Power
Adapter
Headset Base (bottom view)
B. Charge the Headset for at least 20 Minutes before using
1. Gently push the headset into the charging cradle as shown below. The amber Charge Status light on the base will flash to indicate the headset battery is charging. A solid light indicates full charge. A full charge will take approximately 3 hours.
Power |
Charge Status |
(Red) |
(Amber) |
The headset may also be charged directly with the
Headset Travel Charger. Plug the headset travel charger into a wall outlet, then plug the power cord from the adapter into the headset. The indicator light will flash red while the headset battery is charging. The light will change to solid blue when the battery is fully charged.
Plantronics Voyager 510S Setup Guide