5 Easy Steps
The fastest way to setup your CS70 Headset System
Base Power
Adaptor
HL10
Automatic
Handset Lifter*
CS70 Headset
with Ear Tip
CS70
Headset Base
*Not included in all configurations
CS70 Series Setup Guide
CS70 Package Contents
Headset |
Setup Guide |
|
Headset Base with Preinstalled Phone Cable
Base Power Adapter |
Ear Tips |
Please refer to the separate Safety Instructions sheet for important product safety information prior to installation or use of the product.
CS70 With Handset Lifter* Adds:
HL10 Automatic |
HL10 |
|
User Guide |
||
Handset Lifter |
||
|
*Automatic Handset Lifter is bundled with certain CS70 configurations and also available separately.
HL10 Additional Parts Kit (if needed)
Extender |
Ringer |
Adapter for |
Arm |
Microphone |
Nortel i2004 |
|
|
Phones |
Plantronics CS70 Setup Guide
P1Install Ear Tip & Adjust fit
ET
S
Fit the Headset
Slide the headset over and behind your ear, then press gently toward your ear. Rotate the microphone boom until it is pointed toward your mouth. If the ear tip is uncomfortable, install a different ear tip. See below.
For your safety and comfort, the ear tip should never be inserted into the ear canal.
To Install a Different Ear Tip
Remove the pre-installed ear tip by pushing in and turning the ear tip clockwise, then pull firmly.
Choose the style and size of Ear |
Push in firmly and |
|||||
Tip that fits most comfortably. |
twist counter |
|||||
Align Ear Tip tabs with notches |
clockwise. |
|||||
in headset. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
To view an interactive set-up guide online, visit www.plantronics.com/cs70setup and click on Adjusting Fit.
To Convert for Wearing on Left Ear
A. Rotate microphone |
B. Turn microphone |
C. Rotate microphone |
boom up |
boom around |
boom down |
Questions? For fast, efficient Technical Support call: 800-544-4660 Ext. 5538
S T E P
2Connect Base to Desk Phone
Use Configuration A if:
You will use the Automatic Handset Lifter or…
Your phone has NO built-in headset functionality (no Headset button).
Configuration A
1. Unplug the handset coil cord from the desk phone handset port [A], then plug it
into the green labeled handset port [B] on the Headset Base.
A
Handset |
Handset |
Coil Cord |
|
Headset Base (bottom view)
A B
2. Plug the short black Phone Cable that
is pre-installed on the Headset Base into the now-open handset port [A] on the desk phone.
Plantronics CS70 Setup Guide
Use Configuration B if:
You will NOT use the Automatic Handset Lifter and…
Your phone has built-in headset functionality (a Headset button).
Configuration B
Confirm there is
a “Headset” button on your phone
Headset Base (bottom view)
C
1. Plug the short BLACK Phone Cable that is pre-installed on the Headset Base into the Heaset port [C] on the desk phone.
Handset port or Headset port?
You should only use the headset port if you will not be using the Automatic Handset Lifter and you have a pre-programmed Headset button on your phone.
In this configuration you must press both the Headset button on your phone and the Call Control Button on the headset to answer/end calls.
Questions? For fast, efficient Technical Support call: 800-544-4660 Ext. 5538