USER GUIDE_
PLANTRONICS EXPLORER™ 300 Series
BLUETOOTH® HEADSET
72357-01 (04-06)
TABLE OF CONTENTS
Package Contents & Features |
3 |
Charging & Powering |
5 |
|
|
Pairing |
6 |
Adjusting Fit |
7 |
|
|
Using Your Headset |
8 |
Indicator Lights |
9 |
|
|
Accessories |
10 |
Troubleshooting |
12 |
|
|
Product Specifications |
12 |
Technical Assistance |
13 |
|
|
Warranty |
13 |
Regulatory Notices |
14 |
WELCOME
Thank you for purchasing a Plantronics headset.
Let us provide you with the best possible service and technical support. After you review this user guide, if you need additional assistance or have any product questions, please contact:
•Plantronics Technical Assistance Center at 866-363-BLUE (2583)
•www.plantronics.com/support
Before getting started, please review the safety booklet included in the package.
REGISTER YOUR PRODUCT ONLINE
Visit www.plantronics.com/productregistration to register your product online so we can provide you with the best possible service and technical support.
PACKAGE CONTENTS & FEATURES
PLANTRONICS EXPLORER 330
Indicator light
Call control button
M |
one |
A |
|
Ear tip |
|
Char |
g jack |
PLANTRONICS EXPLORER 340 AND 350
Indi
Call control button
M one
A |
|
Ear tip |
|
Char |
g jack |
3
PACKAGE CONTENTS & FEATURES
PLANTRONICS EXPLORER 330 & 340
AC power adapter
PLANTRONICS EXPLORER 350
Cradle Mount Options
In-car charging |
Dash mount |
Vent clip |
cradle (shown |
|
|
with vent clip) |
|
|
Vehicle |
USB headset |
charging |
charger |
adapter |
|
4
CHARGING & POWERING
CHARGING
Explorer 330 & 340
2
1
Explorer 350
2
1
Before using, you must first charge your headset. 20 minutes = minimum charge
2 hours = full charge Light is solid red when battery is charging.
NOTE For the best user experience, keep your headset fully charged.
CAUTION Do not use headset while charging and do not connect the charger while the headset is in use.
POWERING
Press the control button for 2 seconds to power on. Press the control button for 3 seconds to power off.
5
PAIRING
1. 2.
3.
Before using your headset for the first time, you must pair it with your Bluetooth® phone or device. Be sure the headset is fully charged. For set up and pairing instructions with Bluetooth devices other than mobile phones, please consult your Bluetooth device user guide.
Begin with headset turned off.
1.Press call control button for
6 seconds. Release button when indicator light flashes blue and red. Headset is ready to pair with Bluetooth device.
NOTE The headset can pair to multiple Bluetooth devices, but will only connect to one device at a time. The headset will automatically connect to the last device to which it was connected.
2.While the headset is flashing red and blue, use the phone menu to search for Bluetooth devices and select “3XXPlantronics”.
3.When prompted for passkey enter 0000. Headset will flash blue when paired successfully.
6
ADJUSTING FIT
1. 2.
R |
t Ear |
L |
Ear |
Lift ear loop. |
Swivel ear loop to the right or left for |
|
right or left ear wearing. |
3. |
4. |
5. |
Place ear loop |
Pivot headset to |
Position speaker and |
behind ear. |
place speaker |
align microphone with |
|
into ear. |
mouth. |
7
USING YOUR HEADSET
ANSWERING/ENDING/MAKING CALLS
For best performance, position your mobile phone on the same side of your body as the headset.
To answer or end a call, briefly press the call control button.
To make a call, enter number on your phone, press send, and the call is automatically transferred to headset; no need to press call control button.
ADJUSTING THE VOLUME
Briefly push up or down on the call control button for incremental volume steps. You will hear two tones (high tone followed by low tone) at the volume limit.
WARNING For your comfort, health, and safety, do not exceed moderate listening levels.
8
USING YOUR HEADSET
ADDITIONAL FEATURES
Redialing Last Number
To activate last number redial, double press the call control button. You will hear a high tone after each double key press.
Using Voice Dialing
With the headset on, press the call control button for 2 seconds to activate the voice dialing.
Rejecting a Call
When receiving an incoming call, press the call control button for 2 seconds to reject the call.
Switching a Call From Phone to Headset
To switch an active call from your phone to your headset, press the call control button for 3 seconds.
NOTE To use voice activated dialing, the voice dialing feature must be enabled on your phone. See your Bluetooth phone manual for instructions.
Switching a Call From Headset to Phone
To switch an active call from your headset to your phone, press the call control button for 2 seconds.
INDICATOR LIGHTS
Headset Status |
Headset Indicator Light |
|
|
Powering on |
Blue flashes. Repeat. |
Powering off |
Red appears and goes off. |
|
|
Charging battery |
Red solid light. |
Low battery |
Red flashes. |
|
|
Pairing mode |
Blue/red flashes for 120 seconds. |
Missed call |
Purple flashes. Double press the call control |
|
button to cancel. |
|
|
Ringing |
Purple flashes. Briefly press call control button |
|
to answer the call. Press call control button for |
|
2 seconds to reject the call. |
|
|
9
ACCESSORIES
INCLUDED ACCESSORIES
1. 2.
3. 4.
In-car charging cradle and in-vehicle charging adapter – for Explorer 350 only
1.Select vent clip or dash mount option. Attach to rear of in-car charging cradle.
NOTE Select the mounting option that allows the charging cradle to not interfere with car controls.
2.Insert charging plug into slot on bottom of charging cradle. Be sure to slide to top of slot.
3.Attach charging cradle to dash mount or vent.
IMPORTANT Clip onto lowest vent slot. Be sure the headset is not directly in the vent air flow. If headset cannot be positioned out of air flow, use dash mount instead.
4.Place ear tip as shown in the top of the cradle. Gently press the bottom of the headset to plug the charging adapter into the charging jack. Then plug in-vehicle charging adapter into vehicle power.
10