Plantronics 395, 242, 245, 243 User Manual

0 (0)

Welcome

Thank you for purchasing the Plantronics Explorer 240, 242, 243, 245, or 395 headset. This guide contains instructions for setting up and using your new headset.

Please refer to the separate For Your Safety guide for important product safety information prior to installation or use.

Getting Assistance

The Plantronics Technical Assistance Center is ready to assist you. You can find answers to frequently asked questions, ask a question using e-mail, receive service over the Internet, or speak directly with a representative. Visit www.plantronics.com/support.

note If you are considering returning this headset, please contact the Technical Assistance Center first.

Registering Your Product

Visit www.plantronics.com/productregistration to register your product online so we can provide you with the best service and technical support.

Note For pairing your headset, your PIN code/Passkey is 0000.

ii

Contents

Package Contents and Features...........................................................

iv

Charging Your Headset.........................................................................

1

Using the AC charger...................................................................

1

What is Bluetooth®?..............................................................................

2

Plantronics QuickPair® Technology...............................................

2

Range (the distance between headset and phone).......................

2

Pairing Your Headset.............................................................................

3

Adjusting the Fit....................................................................................

4

Headset Controls and Indicators...........................................................

6

Troubleshooting.....................................................................................

9

Product Specifications........................................................................

10

iii

Plantronics 395, 242, 245, 243 User Manual

Package Contents and Features

Note Your headset may look different than the illustration, but will still work as described.

Headset Front*

Volume Control Button

Call Control Button

Status Light

Power On/Off Switch

Swivel Earloop [fits either ear]

Headset Back

Microphone

Speaker/Eartip

Micro USB Charging Jack

Power On/Off Switch

AC Charger 100 – 240V

* For illustration purposes only; designs will vary by model number.

iv

Charging Your Headset
Your new headset performs best when it is fully charged. While your headset is charging, the indicator light glows red. When your headset is fully charged, the indicator light turns blue.
How to Charge Your Headset Using the AC Charger
1 Plug the charger into a power outlet.
2 Connect the charger cable to the headset.
1 1

C h a r g i n g t i m e

2 hours........................

Full charge

 

 

1 hour..........................

Minimum charge

 

before first use

2

2

note Never charge the battery where the temperature may fall below 32°F (0°C) or rise above 104°F (40°C). Do not use your earpiece while it is connected to the charger.

1

What Is Bluetooth?

Bluetooth wireless technology provides a way for devices, like headsets and phones, to communicate with each other without wires. Pairing is the set-up process of introducing your headset to your phone.

Before using your headset for the first time, you must pair it with your Bluetooth-enabled phone.

Plantronics QuickPair™ Technology

To simplify the Bluetooth setup process, your new headset uses Plantronics QuickPair technology. This process is shown on the next page.

The first time you turn your headset on, your headset automatically enters pairing mode for 10 minutes.

Until you successfully pair your headset with a Bluetoothenabled phone, every time you turn it on it will enter pairing mode.

To later pair to a new phone, turn on the headset, then press and hold the Call Control button until red then blue flashing appears, which indicates pairing mode status.

Range (the distance between headset and phone)

To maintain the connection, keep your headset within 33 feet of your phone.

For the least amount of interference place the headset and phone on the same side of your body.

If you move too far from your phone and lose the Bluetooth connection:

the headset may reconnect automatically within 60 seconds when you move closer to your phone (you will hear a low tone), OR

you may have to tap the Call Control button to reconnect (you will hear a low tone), OR

if neither of the above options work, you may have to reconnect to your headset using your phone’s Bluetooth menu.

2

Loading...
+ 10 hidden pages