Planet Technology FT-90X, FT-902S15, FT-902S50, FT-906A20, FT-902 User Manual

...
0 (0)
Planet Technology FT-90X, FT-902S15, FT-902S50, FT-906A20, FT-902 User Manual

User's Manual

FT-902

FT-902S15/S35/S50

FT-905A

FT-906A20/906B20

10/100Base-TX to 100Base-FX Web Smart Media Converter

Trademarks

Copyright © PLANET Technology Corp. 2007. Contents subject to which revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.

Disclaimer

PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.

PLANET has made every effort to ensure that this User's Manual is accurate; PLANET disclaims liability for any inaccuracies or omissions that may have occurred.

Information in this User's Manual is subject to change without notice and does not represent a commitment on the part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User's Manual. PLANET makes no commitment to update or keep current the information in this User's Manual, and reserves the right to make improvements to this User's Manual and/or to the products described in this User's Manual, at any time without notice.

If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your comments and suggestions.

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at whose own expense.

CE Mark Warning

This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

WEEE Warning

To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.

Revision

PLANET Fast Ethernet Web Smart Media Converter User's Manual

FOR MODELS: FT-902/FT-902S15/FT-902S35/FT-902S50/FT-905A/FT-906A20/FT-906B20

REVISION: 1.0 (FEBRARY.2007)

Part No.: 2080-AA3450-000

-2-

 

TABLE OF CONTENTS

1. INTRODUCTION.............................................................................................................................................................

1

1.1 PACKAGE CONTENTS ....................................................................................................................................................

1

1.2 HOW TO USE THIS MANUAL ...........................................................................................................................................

1

1.3 PRODUCT FEATURES ....................................................................................................................................................

1

1.4 PRODUCT SPECIFICATION.....................................................................................................................................

2

2. INSTALLATION..............................................................................................................................................................

3

2.1 PRODUCT DESCRIPTION ................................................................................................................................................

3

2.1.1 FT-90X Front Panel.............................................................................................................................................

4

2.1.2 LED Indicators.....................................................................................................................................................

5

2.1.3 FT-90X Rear Panel .............................................................................................................................................

6

2.2 INSTALL THE CONVERTER ..............................................................................................................................................

7

2.2.1 Stand-alone Installation.......................................................................................................................................

7

2.2.2 Chassis Installation and Rack Mounting .............................................................................................................

9

3. WEB MANAGEMENT..................................................................................................................................................

11

3.1 OVERVIEW .................................................................................................................................................................

11

3.2 MANAGEMENT METHODS.............................................................................................................................................

11

3.2.1 Web Management.............................................................................................................................................

11

3.2.2 Login the media converter.................................................................................................................................

12

4. CONFIGURATION........................................................................................................................................................

13

4.1 MAIN MENU ...............................................................................................................................................................

13

4.2 SYSTEM.....................................................................................................................................................................

14

4.2.1 System Information ...........................................................................................................................................

14

4.2.2 IP Configuration ................................................................................................................................................

15

4.2.3 Password Setting ..............................................................................................................................................

16

4.3 PORT CONFIGURATION................................................................................................................................................

17

4.4 CONVERTER CONFIGURATION ......................................................................................................................................

20

4.5 CONVERTER STATUS ..................................................................................................................................................

24

4.6 STATISTICS ................................................................................................................................................................

25

4.7 TOOLS.......................................................................................................................................................................

27

4.7.1 Loop Back Test .................................................................................................................................................

27

4.7.2 System Reboot..................................................................................................................................................

29

4.7.3 Configuration Setting.........................................................................................................................................

29

4.7.4 Firmware Upgrade ............................................................................................................................................

32

5. TROUBLESHOOTING..................................................................................................................................................

35

APPENDIX A ....................................................................................................................................................................

36

A.1 DEVICES RJ-45 PIN ASSIGNMENTS .............................................................................................................................

36

A.2 RJ-45 CABLE PIN ASSIGNMENT ....................................................................................................................................

36

A.3 FIBER OPTICAL CABLE CONNECTION PARAMETER .........................................................................................................

37

A.4 POWER INFORMATION.................................................................................................................................................

37

A.4 AVAILABLE MODULES..................................................................................................................................................

37

 

 

 

-3-

1. INTRODUCTION

1.1 Package Contents

Check the contents of your package for following parts:

Web Smart Media Converter x1

CD-ROM user's manual x1

Quick installation guide x1

External 5VDC/2A power adapter x 1

If any of these are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the original packing material, and use them against to repack the product in case there is a need to return it to us for repair.

#Note: FT-905A is with one vacant SFP module slot. The 100Base-FX SFP module is not bundled with in the package

1.2 How to Use This Manual

This Web Smart Media Converter User Manual is structured as follows:

Section 2, Installation

It explains the functions of FT-90x and how to physically install the FT-90x.

Section 3, Web Management

The chapter explains how to manage the converter by Web interface.

Section 4, Configuration

It contains information about the Smart function of FT-90x.

Appendices

It contains cable information of FT-90x.

1.3 Product Features

yOne-channel media conversion between 10/100Base-TX and 100Base-FX

yComplies with IEEE 802.3, IEEE 802.3u 10/100Base-TX, 100Base-FX standard

yAuto-Negotiation for 100Base-TX Half-Duplex or 100Base-Full-Duplex

yCompact size

yCo-work with PLANET MC family Media Chassis ( MC-700/1000R/1500)

yBuilt-in IP-Base Web interface for remote management

yLayer 2 Smart Feature

;IEEE 802.3x Full-Duplex Flow-Control, Back-Pressure in Half-Duplex eliminate packets loss

;Supports Maximum frame size to 2Kbytes.

;Supports auto MDI/MDI-X function on RJ-45 Port

;Store-and-forward mechanism

;Supports two priority queue level

;Supports QoS Scheme (Port based & 802.1p)

-1-

 

 

 

 

 

; Supports Bandwidth Control (Kbps) for both Ingress and Egress

 

 

 

 

 

 

 

 

 

 

 

 

 

 

; Supports Broadcast Storm Control to optimize network bandwidth.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

; Supports Ethernet Statistics on both TP and Fiber interface

 

 

 

 

 

 

 

 

 

 

 

 

 

 

; Look Back Test Function(LBT) , Link Loss Return(LLR)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

; Firmware upgrade via HTTP protocol

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

y

5VDC power supply

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

y

LED indicators for easy network diagnose

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

y Reset Button at the front panel for reset to factory default

 

 

 

 

 

 

 

 

 

 

 

 

 

 

y

Choice of fiber-connector from ST, SC, MT-RJ/VF-45 and WDM, multi-mode / single-mode fiber /100Base SFP

1.4 PRODUCT SPECIFICATION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Model

 

 

 

 

 

 

 

 

FT-902

 

 

FT-902S

 

 

FT-902S

 

 

FT-902S

 

 

FT-905A

 

 

FT-906A

 

 

FT-906B

 

 

 

 

 

 

 

 

 

 

 

 

 

15

 

 

35

 

 

50

 

 

 

 

20

 

 

20

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Hardware Specification

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ports

 

 

 

 

 

 

 

1 x 10/100Base-TX port,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 x 100Base-FX port

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Optic Interface

 

 

 

 

 

 

 

SC

 

 

 

 

 

 

SFP

 

WDM

 

 

Optic wavelength

 

 

 

 

1300nm

 

1310nm

 

1310nm

 

1310nm

-

 

 

TX:1310

 

 

TX:1550

 

 

 

 

 

 

 

 

 

 

 

RX:1550

 

 

RX:1310

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Launch

 

 

 

 

Max.

 

 

-14

 

 

-7

 

 

-5

 

-0

 

-

 

 

 

-8

 

 

 

 

Power(dBm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Min.

 

 

 

-19.0

 

 

-20

 

 

-9

 

-5

 

-

 

 

 

-14

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Receive Sensitivity

 

 

 

 

 

-34.5

 

 

-28

 

 

-32

 

-34

 

-

 

 

 

-31

 

 

 

Maximum Input power

 

 

-14

 

 

-8

 

 

-5

 

-8

 

-

 

 

 

*

 

 

 

 

 

 

 

 

Twisted-pair

 

 

 

10Base-T: 2-pair UTP Cat. 3,4,5, up to 100 m

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

100Base-TX: 2-pair UTP Cat. 5, up to 100 m

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cable

 

 

 

 

 

 

 

 

50/125μm or 62.5/125μm multi-mode fiber cable, up to 2km.

 

 

 

 

 

 

 

 

 

 

Fiber-optic cable

 

 

9/125μm single-mode cable, provide long distance for 15/20/35/50km or longer

 

 

 

 

 

 

 

 

 

 

 

 

 

(very on SFP module)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Speed

 

 

Twisted-pair

 

 

 

10/20Mbps for Half/Full-duplex

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

100/200Mbps for Half/Full-duplex

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fiber-optic

 

 

 

200Mbps for Full-Duplex

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Dimension

 

 

 

26 x 70 x 97mm (H x W x D)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Power Requirement

 

 

 

5V DC 2A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Standard Conformance

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IEEE 802.3, 10Base-T

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Standards

 

 

 

IEEE 802.3u, 100Base-TX, 100Base-FX

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IEEE 802.3x Flow Control

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IEEE 802.1p Class of Service

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Operating Temperature

 

0~50ºC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Storage Temperature

 

-25~70ºC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Operating Humidity

 

 

 

10% to 90% , relative humidity, non-condensing

 

 

 

 

 

 

 

 

 

 

 

Storage Humidity

 

 

 

10% to 90% , relative humidity, non-condensing

 

 

 

 

 

 

 

 

 

 

 

Regulation Compliance

 

 

FCC Part 15 Class B, CE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-2-

2. INSTALLATION

This section describes the functionalities of FT-90X’s components and guides how to install it on the desktop or shelf. Basic knowledge of networking is assumed. Please read this chapter completely before continuing.

2.1 Product Description

The Web-Smart FT-90x Media Converters supports conversion between 10/100Base-TX and 100Base-FX network. There are SC/SFP connectors and single-mode/multi-mode media for your needs. Ethernet signal that allows two type segments connect easily, efficiently and inexpensively. This converter can be used as a stand-alone unit or as a slide-in module to the PLANET Media Converter Chassis (MC-700, MC-1000 and MC-1500).

Each Web-Smart converter is able to manage through the Web Interface. The powerful Web-Smart Media Converter supports flow control, QoS, bandwidth control and Ingress/Egress rate control, etc. The statistics function of the Web-Smart converter help the administrator to remote analysis and count the packet flow of the current Ethernet link.

The Web-Smart function also includes the LLR and Loop Back Test. LLR can immediately alarm administrators the problem of the link media and provide efficient solution to monitor the net. It provides more flexible settings for converters.

LLR (Link Loss Return) means when a device connected to the converter and the fiber line loss the link, the converter’s fiber will disconnect the link of transmit. The LLR function can immediately alarm administrators the problem of the link media and provide efficient solution to monitor the net.

With 100Base-FX SFP ports, the FT-905A is with high reliability and flexibility to extend the distance up to 2Km, 20Km, or longer. It depends on the 100Base-FX SFP transceiver modules.

Supplier and Model name:

PLANET FT-90X (firmware version 1.0)

y X =

1

ST

 

 

2

SC

 

 

5

SFF/LC

 

 

5A

SFP

 

 

6

WDM

 

 

6A

TX1310;RX1510

 

 

6B

TX1510;RX1310

 

 

-3-

2.1.1 FT-90X Front Panel

Figure 2-1, 2-2 & 2-3 shows a front panel of FT-90X.

Figure 2-1 PLANET FT-902/FT-902S Front Panel

Figure 2-2 PLANET FT-905A Front Panel

Figure 2-3 PLANET FT-906A/B Front Panel

-4-

2.1.2 LED Indicators

System

LED

Color

Function

PWR

Green

Lit: Power on.

10/100Base-TX Port

LED

Color

 

Function

 

 

Lit:

Indicate that the port is link up.

 

 

 

 

LNK/ACT

Green

Blink:

Indicate that the converter is actively sending or receiving data over

 

that port.

 

 

 

 

 

 

 

 

 

Off:

Indicate that the port is link down or no data flow.

 

 

 

 

 

 

Lit:

Indicate that the connection made through the corresponding port is

FDX

Green

 

running in Full-Duplex mode.

 

 

Off:

Indicate that the connection made through the corresponding port is

 

 

 

 

 

running in Half-Duplex mode.

 

 

 

 

100

Green

Lit:

Indicate that the port is operating at 100Mbps.

 

 

Off:

Indicate that the port is link down or 10Mbps.

 

 

 

 

 

 

100Base-FX SC/SFP Port

 

LED

Color

 

Function

 

 

Lit:

Indicate that the port is link up.

 

 

 

 

LNK/ACT

Green

Blink:

Indicate that the converter is actively sending or receiving data over

 

that port.

 

 

 

 

 

 

 

 

 

Off:

Indicate that the port is link down or no data flow.

 

 

 

 

 

 

Lit:

Indicate that the connection made through the corresponding port is

FDX

Green

 

running in Full-Duplex mode.

 

 

Off:

Indicate that the connection made through the corresponding port is

 

 

 

 

 

running in Half-Duplex mode.

 

 

 

 

#Note: To press and release the RESET button. The FX-90x will back to the factory default mode. Be sure that you backup the current configuration of FT-90X; else the entire configuration will be erased when pressing the “RESET” button.

Press and release the RESET button shortly, the device will be rebooted.

Press the RESET button more than 10 seconds, the device will back to the factory default mode; the entire configuration will be erased.

-5-

2.1.3 FT-90X Rear Panel

The rear panel of the converter indicates one DC jack, which accepts input power with 5V DC 2A.

FT-90x series

Figure 2-6 Rear Panel of FT-90x

Power Notice:

1.The device is a power-required device, it means, it will not work till it is powered. If your networks should active all the time, please consider using UPS (Uninterrupted Power Supply) for your device. It will prevent you from network data loss or network downtime.

2.In some area, installing a surge suppression device may also help to protect your media converter from being damaged by unregulated surge or current to the converter or the power adapter.

-6-

2.2 Install the Converter

This section describes how to install your FT-90X Web Smart Media Converter and make connections to the converter. Please read the following topics and perform the procedures in the order being presented. The hardware installation of PLANET FT-90X Web Smart Media Converter do not need software configuration. To install your FT-90X on a desktop or shelf, simply complete the following steps.

10/100Base-TX Cat. 5/5e TP Cable Network

FT-90X

 

100Base-FX

10/100Base-TX to 1000Base-FX

Fiber Network

Web Smart Media Converter

 

2.2.1 Stand-alone Installation

To install a FT-90X stand-alone, on a desktop or shelf, simply complete the following steps:

Step 1: Turn off the power of the device/station in a network to which the FT-90X will be attached.

Step 2: Ensure that there is no activity in the network.

Step 3: Attach fiber cable from the FT-90X to the fiber network. TX, RX must be paired at both ends.

Step 4: Connect the 5VDC power adapter to the FT-90X and verify that the Power LED lights up.

Step 5: Turn on the power of the device/station; the PWR LEDs should light when all cables are attached.

-7-

#Note: Please refers to APPENDIX-A for detailed wiring information of the FT-90X.

To prevent from optic acceptor malfunction, check the both wires / transmitter before power on the converter.

FT-905A Installation

FT-905A is with high reliability and flexibility to extend the distance up to 2Km, 20Km, or longer. It depends on the 100Base-FX SFP transceiver modules. The SFP transceivers are hot-plug e and hot-swappable. You can plug-in and out the transceiver to/from any SFP port without having to power down the converter.

To install FT905A with 100Base-FX SFP, simply complete the following steps:

Step 1: Precede with the steps 4 and steps 5 of session 2.2.1 Stand-alone Installation to connect the network cabling and supply power to your converter.

Step 2: Slot in the 100Base-FX SFP. Make sure both side of the SFP transfer are with the same media type, for example: 100Base-FX/2Kmto 100Base-FX/2Km, 100Bas-FX/20Km to 100Base-FX/20Km.

# It recommends using PLANET MFB-FX series 100Base-FX SFP on the converter. If you insert a Note: SFP transceiver that is not supported, the converter will not recognize it.

Step 3: Connect the fiber cable. Attach the duplex LC connector on the network cable into the SFP transceiver.

-8-

2.2.2 Chassis Installation and Rack Mounting

To install the media converter in a 10-inch or 19-inch with standard rack, follow the instructions described below.

Step 1: Place your FT-90X on a hard flat surface, with the front panel positioned towards your front side.

Step 2: Carefully slide in the module until it is fully and firmly fitted into the slot of the chassis.

Figure 2-1: Insert a media converter into an available slot

Step 3: Attach a rack-mount bracket to each side of the Chassis with supplied screws attached to the package.

Step 4: After the brackets are attached to the chassis, use suitable screws to securely attach the brackets to the rack, as shown in Figure 2-2.

Step 5: Precede with the steps 4 and steps 5 of session 2.2.1 Stand-alone Installation to connect the network cabling and supply power to your converter.

Caution: You must use the screws supplied with the mounting brackets. Damage caused to the parts by using incorrect screws would invalidate your warranty.

-9-

Loading...
+ 28 hidden pages