HTZ363DVD
DVD/CD Receiver | DVD/CD
XV-DV767
Speaker System |
S-DV363
HTZ565DVD
DVD/CD Receiver | DVD/CD
XV-DV767
Speaker System |
S-DV2T
S-DV2SW
HTZ767DVD
DVD/CD Receiver | DVD/CD
XV-DV767
Speaker System |
S-DV4T S-DV2SW
Operating Instructions
Thank you for buying this Pioneer product.
Please read through these operating instructions so that you will know how to operate your model properly. After you have finished reading the instructions, put them in a safe place for future reference.
Location: bottom of the unit
IMPORTANT
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
D3-4-2-1-1_En-A
WARNING
This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filed with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture.
WARNING
Before plugging in for the first time, read the following section carefully.
The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e.g., 230 V or 120 V) written on the rear panel.
WARNING
To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment.
VENTILATION CAUTION
When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 10 cm at top, 10 cm at rear, and 10 cm at each side).
WARNING
Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed.
CAUTION
The STANDBY/ON switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation).
D3-4-2-2-2a_A_En
CAUTION
This product is a class 1 laser product, but this product contains a laser diode higher than Class 1.
To ensure continued safety, do not remove any covers or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel.
The following caution label appears on your unit. Location: top of the unit
CAUTION : CLASS 3B VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN, AVOID
EXPOSURE TO THE BEAM.
VRW2159
CLASS 1
LASER PRODUCT
D3-4-2-1-8_B_En
POWER-CORD CAUTION |
Operating Environment |
Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement.
This product is for general household purposes. Any failure due to use for other than household purposes (such as long-term use for business purposes in a restaurant or use in a car or ship) and which requires repair will be charged for even during the warranty period.
Operating environment temperature and humidity: +5 ºC to +35 ºC (+41 ºF to +95 ºF); less than 85 %RH (cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light)
If the AC plug of this unit does not match the AC outlet you want to use, the plug must be removed and appropriate one fitted. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. If connected to an AC outlet, the cut-off plug can cause severe electrical shock. Make sure it is properly disposed of after removal.
The equipment should be disconnected by removing the mains plug from the wall socket when left unused for a long period of time (for example, when on vacation).
Contents
01 Controls and displays
Front panel . . . . . . . . . . . . . . . . . . . . . . . . .6 Remote control . . . . . . . . . . . . . . . . . . . . . .7 Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
02 Getting started
Home theater sound setup . . . . . . . . . . . .10 Using the Auto MCACC setup for optimal surround sound . . . . . . . . . . . . . . . . . . . . .10
Using the on-screen displays . . . . . . . . . . .11
Playing discs . . . . . . . . . . . . . . . . . . . . . . .12
Basic playback controls. . . . . . . . . . . . . .12 Resume and Last Memory. . . . . . . . . . . .13 DVD-Video disc menus . . . . . . . . . . . . . .13 Video CD/Super VCD PBC menus . . . . . .13 Listening to the radio . . . . . . . . . . . . . . . . .13 Improving poor FM reception . . . . . . . . .14 Reducing AM reception noise . . . . . . . . .14 Memorizing stations . . . . . . . . . . . . . . . .14 Listening to station presets . . . . . . . . . . .14 Listening to other sources . . . . . . . . . . . . .14
03 Listening to your system
Auto listening mode . . . . . . . . . . . . . . . . .15
Listening in surround sound . . . . . . . . . . .15 Dolby Pro Logic II Music settings . . . . . .15 Using Front Stage Surround Advance . . . .16 Using Advanced Surround. . . . . . . . . . . . .16
Listening in stereo . . . . . . . . . . . . . . . . . . .16
Listening with headphones . . . . . . . . . . . .16 Listening with Acoustic Calibration EQ . . .16 Using the Sound Retriever . . . . . . . . . . . . .17
Enhancing dialog. . . . . . . . . . . . . . . . . . . .17
Using the Tone controls. . . . . . . . . . . . . . .17 Adjusting the bass and treble . . . . . . . . .17 Quiet and Midnight modes . . . . . . . . . . .17 Boosting the bass level . . . . . . . . . . . . . . .17
04 Disc playback features
Scanning discs . . . . . . . . . . . . . . . . . . . . . 18
Playing in slow motion . . . . . . . . . . . . . . . 18 Frame advance/frame reverse . . . . . . . . . . 18 Playing a JPEG slideshow . . . . . . . . . . . . . 18 Browsing DVD or Video CD/Super VCD discs with the Disc Navigator . . . . . . . . . . 19 Browsing WMA, MP3, MPEG-4 AAC,
DivX video and JPEG files with the
Disc Navigator. . . . . . . . . . . . . . . . . . . . . . 20 Using Playlists. . . . . . . . . . . . . . . . . . . . . . 20
Programming playlists . . . . . . . . . . . . . . 20 Listening to playlists . . . . . . . . . . . . . . . . 21 Clearing files from a playlist . . . . . . . . . . 21 Looping a section of a disc . . . . . . . . . . . . 21
Using repeat play . . . . . . . . . . . . . . . . . . . 21 Using random play . . . . . . . . . . . . . . . . . . 21
Creating a program list . . . . . . . . . . . . . . . 22 Other functions available from the program menu . . . . . . . . . . . . . . . . . . . . 22
Searching a disc . . . . . . . . . . . . . . . . . . . . 23 Switching subtitles . . . . . . . . . . . . . . . . . . 23
Switching language/audio channels . . . . . 23
Zooming the screen . . . . . . . . . . . . . . . . . 23
Switching camera angles . . . . . . . . . . . . . 24 Displaying disc information. . . . . . . . . . . . 24
05 USB playback
Using the USB interface . . . . . . . . . . . . . . 25 Basic playback controls . . . . . . . . . . . . . . 25
Scanning files . . . . . . . . . . . . . . . . . . . . . . 26
Playing a JPEG slideshow . . . . . . . . . . . . . 26 Browsing files with the Navigator . . . . . . . 26
06 Surround sound settings
Using the Setup menu . . . . . . . . . . . . . . . 27
07 Video Adjust menu
Video Adjust menu . . . . . . . . . . . . . . . . . . 28
4
En
08 Initial Settings menu
Using the Initial Settings menu . . . . . . . . 29 Video Output settings. . . . . . . . . . . . . . . . 29
Language settings . . . . . . . . . . . . . . . . . . 30 Display settings . . . . . . . . . . . . . . . . . . . . 30 Options settings. . . . . . . . . . . . . . . . . . . . 31 Parental Lock. . . . . . . . . . . . . . . . . . . . . 31
About DivX® VOD content. . . . . . . . . . . 32
09 Other connections
Connecting external antennas . . . . . . . . . 33 Connecting auxiliary audio
components . . . . . . . . . . . . . . . . . . . . . . . 33 Recording mode . . . . . . . . . . . . . . . . . . 33
Connecting the S-video output . . . . . . . . . 34 Connecting using the component video output . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
About progressive scan video . . . . . . . . 34 Connecting using HDMI. . . . . . . . . . . . . . 35 Switching the HDMI audio setting . . . . . 35 Resetting the HDMI connection. . . . . . . 35
About HDMI. . . . . . . . . . . . . . . . . . . . . . . 35
Using this unit with a Pioneer plasma television . . . . . . . . . . . . . . . . . . . . . . . . . 36
SR+ Setup for Pioneer plasma
televisions . . . . . . . . . . . . . . . . . . . . . . . 36
Switching on the SR+ mode . . . . . . . . . 37 About control out connections . . . . . . . . . 37
10 Additional information
Optional system settings . . . . . . . . . . . . . .38 Setting the sleep timer. . . . . . . . . . . . . . . .38
Dimming the display . . . . . . . . . . . . . . . . .39
Disc/content format playback
compatibility . . . . . . . . . . . . . . . . . . . . . . .39
Disc compatibility table . . . . . . . . . . . . . .39 About DVD+R/DVD+RW
compatibility . . . . . . . . . . . . . . . . . . . . . .40 About DivX . . . . . . . . . . . . . . . . . . . . . . .40 About MPEG-4 AAC. . . . . . . . . . . . . . . . .41 About WMA . . . . . . . . . . . . . . . . . . . . . .41
Using and taking care of discs. . . . . . . . . .41
DVD Video regions . . . . . . . . . . . . . . . . .42
Installation and maintenance . . . . . . . . . .42 Hints on installation . . . . . . . . . . . . . . . .42 Cleaning the pickup lens . . . . . . . . . . . . .42 Problems with condensation. . . . . . . . . .42 Moving the system unit . . . . . . . . . . . . . .42
Screen sizes and disc formats . . . . . . . . . .43
Troubleshooting. . . . . . . . . . . . . . . . . . . . .44 General . . . . . . . . . . . . . . . . . . . . . . . . . .44
DVD/CD/Video CD player. . . . . . . . . . . . .45
Tuner. . . . . . . . . . . . . . . . . . . . . . . . . . . .46 USB connection . . . . . . . . . . . . . . . . . . .46 HDMI connection . . . . . . . . . . . . . . . . . .46 Error Messages . . . . . . . . . . . . . . . . . . . .47 Resetting the system . . . . . . . . . . . . . . . . .48
Using the language code list . . . . . . . . . . .48
Language code list . . . . . . . . . . . . . . . . . .49
Country/Area code list . . . . . . . . . . . . . . . .49
Specifications . . . . . . . . . . . . . . . . . . . . . .50
Español Nederlands Italiano Français Deutsch English
5
En
01 Controls and displays
Chapter 1
Controls and displays
Front panel
7VOLUME +/– buttons
8USB interface
OPEN/CLOSE |
DVD/CD |
|
USB |
VOLUME |
3 |
4 |
5 |
6 |
7 |
STANDBY/ON |
|
|
|
|
PLAY LIST 1 |
PLAY LIST 2 |
PLAY LIST 3 |
|
|
1 2
|
|
10 |
11 |
12 |
|
8 |
9 |
|
|
1 |
STANDBY/ON |
|
|
Switches the system on or into standby.
2 PLAY LIST buttons
Add tracks (during playback), or select a playlist (while stopped) (page 20).
3OPEN/CLOSE
Opens/closes the disc tray.
4DVD/CD
Selects the DVD/CD function and starts/ pauses/resumes playback.
5
Stops playback.
6 USB
Selects the USB function and starts/pauses playback.
Connect a USB device for playback (see USB playback on page 25).
9PHONES jack
Connect headphones.
10Indicator
Lights blue when the power is on (except when the dimmer/sleep timer is active).
11Remote Sensor
12Display
See Display below.
6
En
Controls and displays |
01 |
Remote control
|
STANDBY |
DVD/CD |
TUNER |
SOUND |
1 |
/ON |
(FM/AM) |
RETRIEVER |
|
|
|
|
11 |
|
|
|
USB |
LINE |
OPEN/CLOSE |
2 |
|
12 |
||
|
|
|
||
|
|
|
|
PLAYLIST |
|
1 |
2 |
3 |
1 |
|
|
AUDIO |
SUBTITLE |
|
3 |
4 |
5 |
6 |
2 |
|
ANGLE |
ZOOM |
13 |
|
|
7 |
8 |
9 |
3 |
|
CLEAR |
|
DISPLAY |
|
|
|
0 |
|
|
|
TOPMENU |
TUNE |
|
MENU |
4 |
|
|
|
14 |
5 |
SETUP |
|
|
SR |
ST |
ENTER |
ST |
||
|
HOME |
|
|
|
|
MENU |
|
|
RETURN |
6 |
|
|
|
15 |
|
MCACC |
TUNE |
|
TESTTONE |
7 |
F.S.SURR |
SURROUND |
ADVANCED |
SOUND |
|
|
|
|
|
8 |
|
|
|
|
|
|
TV CONTROL |
|
SLEEP |
9 |
|
|
|
16 |
INPUT |
CHANNEL |
VOLUME |
MUTE |
|
|
SHIFT |
|
|
17 |
10 |
|
VOLUME |
18 |
|
|
|
|||
|
|
|
1 STANDBY/ON
Switches the system on or into standby.
2 Function select buttons
Selects the source you want to listen to (DVD/ CD, TUNER, USB, LINE).
3 Number buttons, CLEAR, DISPLAY and DVD controls
CLEAR
Clears an entry.
DISPLAY
Displays/changes disc information shown on-screen (page 24).
SHIFT+AUDIO
Selects audio channel/language (page 23).
SHIFT+SUBTITLE |
English |
||||
Displays/changes the subtitles (page 23). |
|||||
|
|||||
SHIFT+ANGLE |
|
|
|
|
|
Changes camera angle during DVD multi- |
|
||||
angle scene playback (page 24). |
|
||||
|
|||||
SHIFT+ZOOM |
|
|
|
|
|
|
|
|
Deutsch |
||
Changes the screen zoom level (page 23). |
|
||||
|
|
||||
4 TOP MENU – Displays the top menu of a |
|
|
|||
DVD disc in the play position — this may |
|
|
|||
be the same as pressing MENU (page 13). |
|
|
|||
SHIFT+SETUP |
– Use to make various |
|
Français |
||
|
|
||||
system and surround sound settings |
|
|
|||
(page 14, 27 and 39). |
|
|
|||
5 Cursor, ENTER and tuning buttons |
|
|
|||
|
|
||||
/ / / – Use the cursor buttons to |
|
||||
Italiano |
|||||
command. |
|
|
|
||
navigate on-screen displays and menus. |
|
||||
ENTER – Selects an option or executes a |
|
||||
TUNE +/– – Tunes the radio. |
|
||||
|
|||||
ST +/– – Selects station presets when |
|
|
|||
|
Nederlands |
||||
listening to the radio. |
|
|
|||
|
|
||||
6 HOME MENU – Displays (or exits) the on- |
|
|
|||
screen menu for Initial Settings, Play Mode |
|
|
|||
functions, etc. |
|
|
|
|
|
|
|
|
|
||
SHIFT+MCACC – Starts the Auto MCACC |
Español |
||||
setup (page 10). |
|||||
|
7 Sound controls
F.S.SURR – Selects Front Stage Surround Advance mode (page 16).
SURROUND – Selects a Surround mode (page 15) or switches to stereo playback (page 16).
ADVANCED – Selects a Pioneer original surround mode (page 16) .
SOUND – Accesses the sound menu to adjust the tone, bass and treble, etc. (page 15 to 17 and 33).
7
En
01 Controls and displays
8 Playback controls
See Basic playback controls on page 12, Disc playback features on page 18 and USB playback on page 25 for an explanation of these controls.
9 TV CONTROL buttons
These control Pioneer plasma televisions.
10 SHIFT
Press to access the controls highlighted in green.
11SOUND RETRIEVER – Press to restore CD quality sound to compressed audio sources (page 17).
12OPEN/CLOSE
Opens/closes the disc tray.
13 PLAYLIST buttons
Add tracks (during playback), or select a playlist (while stopped) (page 20).
14MENU – Press to display a USB menu, or the Navigator (page 13, 18 and 26).
SHIFT+SR+ – Switches the SR+ mode on/ off (page 36).
15RETURN – Returns to a previous menu screen.
SHIFT+TEST TONE – Outputs the test tone (for speaker setup) (page 27).
16SLEEP
Press to set the sleep timer (page 38).
17 MUTE
Mutes the sound (press again to cancel).
18 VOLUME +/–
Adjusts the volume.
8
En
Controls and displays
Display
1 |
2 |
3 |
4 |
|
5 |
6 |
7 |
PRGSVE SOUND |
|
REC MODE |
|||||
DTS |
F.SURR. |
|
|
RPT -1 |
|
||
2D |
|
|
|
kHz PGM |
|||
2PL |
|
|
|
MHz RDM |
|||
15 |
14 |
13 12 |
11 |
10 |
9 |
8 |
1 DTS |
9 |
RDM |
Lights during playback of a DTS source |
Lights during random play (page 21). |
|
(page 15). |
10 |
kHz/MHz |
|
2 PRGSVE
Lights when progressive scan video output is selected (page 29).
3 SOUND
Lights when the Sound Retriever is active (page 17).
4SURR.
Lights when one of the Advanced surround listening modes is selected (page 16).
F.SURR.
Lights when one of the Front Stage Surround Advance mode is selected (page 16).
5RPT and RPT-1
RPT lights during repeat play. RPT-1 lights during repeat one-track play (page 21).
6 REC MODE
Lights when Recording mode is on (page 33).
7 PGM
Lights during program play (page 20 and 22).
8 Tuner indicators
Indicates the frequency unit shown in the character display (kHz for AM, MHz for FM).
11Character display
12
Lights when sleep timer is active (page 38).
13
Lights during playback.
14 2 PL II
Lights during Dolby Pro Logic II decoding (page 15).
15 2 D
Lights during playback of a Dolby Digital source (page 15).
– Lights when a broadcast is being received.
– Lights when a stereo FM broadcast is being received in auto stereo mode.
– Lights when FM mono reception is selected.
01
Español Nederlands Italiano Français Deutsch English
9
En
02 Getting started
Chapter 2
Getting started
Home theater sound setup
Place your speakers as shown below for optimal surround sound (see the Speaker Setup Guide for more placement tips).
•Standard surround setup – This is a standard multichannel surround sound speaker setup for optimal 5.1 channel home theater sound.
Front left |
Center |
Front right |
|
Subwoofer |
|
Listening position |
|
|
Surround |
|
Surround |
left |
|
right |
Depending on the size and characteristics of your room, you can choose to use the following
setup option:1
•Front surround setup – This setup is ideal when rear surround speaker placement isn't possible or you want to avoid running long speaker cables in your listening area.
For HTZ565DVD and HTZ767DVD:
Front |
Center |
Front |
|
left |
right |
|
Subwoofer |
Surround |
Surround |
left |
right |
Listening position
After placing your speakers, see Using the Auto MCACC setup for optimal surround sound below to complete your surround setup.
Using the Auto MCACC setup for optimal surround sound
The Multichannel Acoustic Calibration (MCACC) system measures the acoustic characteristics of your listening area, taking into account ambient noise and testing for channel delay and channel level. After you have set up the microphone provided with your system, the receiver uses the information from a series of test tones to optimize the speaker settings and equalization (Acoustic Calibration
For HTZ363DVD:
Front |
Center |
Front |
|
left |
right |
|
Subwoofer |
Surround |
Surround |
left |
right |
Listening position
EQ) for your particular room.2
Important
•These test tones are loud; however, do not turn the volume down during setup as this may result in a sub-optimal calibration.
Note
1See Using Front Stage Surround Advance on page 16 to select a front surround mode when using this setup.
2You only need to use the Auto MCACC setup once (unless you change the placement of your speakers or your room layout).
10
En
Getting started |
02 |
•Make sure the mic and speakers are not moved during the MCACC setup.
|
|
|
|
CLEAR |
DISPLAY |
|
|
|
|
|
|
|
|
|
0 |
|
TV CONTROL |
|
SLEEP |
|
|
|
|
|
|
|
|
||
|
|
|
|
TOPMENU |
TUNE |
MENU |
|
|
|
|
|
|
|
|
|
|
INPUT CHANNEL |
VOLUME |
MUTE |
STANDBY |
|
TUNER |
SOUND |
SETUP |
|
SR |
|
|
|
/ON |
DVD/CD |
(FM/AM) |
RETRIEVER |
|
|
|
|
|
|
|
|
|
|
ST |
ENTER |
ST |
SHIFT |
VOLUME |
|
|
|
|
OPEN/CLOSE |
HOME |
|
|
|
|
|
|
USB |
LINE |
MENU |
|
RETURN |
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
PLAYLIST |
MCACC |
TUNE |
TESTTONE |
|
|
|
1 |
2 |
3 |
1 |
|
|
|
|||
F.S.SURR |
SURROUND ADVANCED |
SOUND |
|
|
|
||||
|
AUDIO |
SUBTITLE |
|
|
|
|
|
|
|
4 |
5 |
6 |
2 |
|
|
|
|
|
|
|
ANGLE |
ZOOM |
|
|
|
|
|
|
|
7 |
8 |
9 |
3 |
|
|
|
|
|
|
•If the noise level is too high, NOISY blinks in the display for five seconds. To exit and check the noise levels1, press SHIFT+MCACC, or to try again, press ENTER when RETRY shows in the display.
•If you see an ERR MIC or ERR SP message in the display, there may be a problem with your mic or the speaker connections. To try again, press ENTER when you see RETRY2.
1 Connect the microphone to the MCACC MIC jack on the rear panel.
|
|
COMPONENT |
PR |
|
|
VIDEO |
|
|
|
VIDEO |
CB/ |
AM LOOP |
FM |
PB |
|
|
UNBAL 75 Ω |
|
|
|
IN |
S-VIDEO |
Y |
|
|
||
|
MCACC |
VIDEO OUT |
|
HDMI OUT SETUP MIC CONTROL |
|
When the MCACC setup is complete, the volume level returns to normal and
COMPLETE3 shows in the display, indicating that the MCACC setup is complete and
Acoustic Calibration EQ has been activated.4
2 Place the microphone at your normal listening position.
Place it about ear height, and make sure it is level by using a table or chair.
Make sure there are no obstacles between the speakers and the microphone.
3 If the system is off, press STANDBY/ON to turn the power on.
If the tuner is selected, switch the input source.
4 Press SHIFT+MCACC.
Try to be as quiet as possible after pressing SHIFT+MCACC. The volume increases automatically and the system outputs a series of test tones.
•Press SHIFT+MCACC to cancel and revert to the previous Auto MCACC settings.
Using the on-screen displays
For ease of use, this system makes extensive use of graphical on-screen displays (OSDs).
All the screens are navigated in basically the same way, using , , , to change the highlighted item and pressing ENTER to select
it.5
Important
•Throughout this manual, ‘Select’ means use the cursor buttons to highlight an item on-screen, then press ENTER.
Button What it does
HOME Displays/exits the on-screen display
MENU
Changes the highlighted menu item
ENTER Selects the highlighted menu item
Note
1• If the room environment is not optimal for the Auto MCACC setup (too much ambient noise, echo off the walls, obstacles blocking the speakers from the microphone) the final settings may be incorrect. Check for household appliances (air conditioner, fridge, fan, etc.), that may be affecting the environment and switch them off if necessary.
•Some older TVs may interfere with the operation of the mic. If this seems to be happening, switch off the TV during the Auto MCACC setup.
2If this doesn’t work, press SHIFT+MCACC, turn off the power, and check the problem indicated by the error message, then try the Auto MCACC setup again.
3If COMPLETE doesn’t appear, it is likely an error occurred during the setup. Please check all connections and try again.
4See Listening with Acoustic Calibration EQ on page 16 to switch on/off Acoustic Calibration EQ.
5The screen saver will appear after five minutes of inactivity.
Español Nederlands Italiano Français Deutsch English
11
En
02 Getting started
Button What it does
RETURN Returns to the main menu without saving changes
Tip
•The button guide at the bottom of every OSD screen shows you which buttons you’ll need to use for that screen.
Playing discs
The basic playback controls for playing DVD, CD, Video CD/Super VCD, DivX video and WMA/MP3/MPEG-4 AAC discs are covered here. Further functions are detailed in chapter 4.
1 If the player isn’t already on, switch it on.
If you’re playing a disc with video, also turn on your TV and make sure that it is set to the correct video input.
2 Press OPEN/CLOSE to load a disc.
Load a disc with the label side facing up, using the disc tray guide to align the disc (if you’re loading a double-sided DVD disc, load it with the side you want to play face down).
3 Press (play) to start playback.
If you’re playing a DVD or Video CD/Super VCD, a menu may appear. See DVD-Video disc menus and Video CD/Super VCD PBC menus on page 13 to navigate these.
If you loaded a disc containing JPEGs, a slideshow will start. See Playing a JPEG slideshow on page 18 for more on this.
•If a disc contains a mixture of DivX video and other media file types (MP3, for example), first select whether to play the DivX video files (DivX) or the other media file types (MP3/WMA/JPEG/MPEG-4 AAC) from the on-screen display.
4 Adjust the volume.
Use the VOLUME control.
Basic playback controls
The following table shows the basic controls on
the remote for playing discs1. You can find other playback features in the chapter 4.
Button What it does
Starts/resumes normal playback.
• If the display shows RESUME or LAST MEM playback starts from the resume or last memory point (see
Resume and Last Memory below).
Pauses/unpauses a disc.
Stops playback or cancels the resume function (if the display shows RESUME).
Press to start fast reverse scanning.
Press to start fast forward scanning.
Skips to the start of the current track or chapter, then previous tracks/chapters.
Skips to the next track or chapter.
Numbers Use to enter a title/chapter/track number. Press ENTER to select.
•If the disc is stopped, playback starts from the selected title (for DVD) or track (for CD/Video CD/Super VCD).
•If the disc is playing, playback jumps to the start of the selected title (VR mode DVD-R/-RW), chapter (DVDVideo) or track (CD/Video CD/Super VCD).
Note
1 You may find with some DVD discs that some playback controls don’t work in certain parts of the disc.
12
En
Getting started |
02 |
Resume and Last Memory
When you stop playback of a disc, RESUME shows in the display indicating that you can resume playback from that point.
With DVDs and Video CD/Super VCDs, even if
ejected, the play position is stored in memory.1 The next time you load the disc, the display shows LAST MEM and you can resume playback.
If you want to clear the resume point, press (stop) while RESUME is displayed.
DVD-Video disc menus
Many DVD-Video discs contain menus from which you can select what you want to watch.
Sometimes DVD-Video menus are displayed automatically when you start playback; others only appear when you press MENU or TOP MENU.
Button |
What it does |
TOP MENU Displays the ‘top menu’ of a DVD disc — this varies with the disc.
MENU Displays a DVD disc menu — this varies with the disc and may be the same as the ‘top menu’.
Moves the cursor around the screen.
ENTER Selects the current menu option.
RETURN Returns to the previously displayed menu screen.
Numbers Highlights a numbered menu option (some discs only). Press ENTER to select.
Video CD/Super VCD PBC menus
Some Video CD/Super VCDs have menus from which you can choose what you want to watch. These are PBC (Playback control) menus.
You can play a PBC Video CD/Super VCD without having to navigate the PBC menu by starting playback using a number button to select a track, rather than the (play) button.
Button |
What it does |
RETURN |
Displays the PBC menu. |
|
|
Numbers |
Selects numbered menu options. |
|
Press ENTER to select. |
|
|
|
Displays the previous menu page |
|
(if there is one). |
|
|
|
Displays the next menu page (if |
|
there is one). |
|
|
|
|
Listening to the radio
The tuner can receive both FM and AM broadcasts, and lets you memorize your favorite stations so you don’t have to manually tune in every time you want to listen.
1Press TUNER to switch to the tuner, then press repeatedly to select the AM or FM band.
The display shows the band and frequency.
2Tune to a frequency.
There are three tuning modes — manual, auto, and high-speed:
•Manual tuning: Press TUNE +/– repeatedly to change the displayed frequency.
•Auto tuning: Press and hold TUNE +/– until the frequency display starts to move, then release. The tuner will stop on the next station it finds. Repeat to keep searching.
•High-speed tuning: Press and hold
TUNE +/– until the frequency display starts to move rapidly. Keep the button held down until you reach the frequency you want. If necessary, fine tune the frequency using the manual tuning method.
Español Nederlands Italiano Français Deutsch English
Note
1• The Last Memory function may not work with some discs.
• For DVD-Video discs (except VR mode DVD-R/-RW), the player stores the play position of the last five discs.
13
En
02 Getting started
Improving poor FM reception
If you’re listening to an FM station in stereo but the reception is weak, you can improve the sound quality by switching to mono.
1Tune to an FM radio station then press SHIFT+SETUP.
2Use /to choose FM MODE then press
ENTER.
3Use / to select FM MONO then press
ENTER.
The mono indicator () lights when the tuner is in mono reception mode.
Select FM AUTO above to switch back to autostereo mode (the stereo indicator () lights when receiving a stereo broadcast).
Reducing AM reception noise
If AM reception seems particularly poor, or the AM radio station you’re listening to seems noisy, try using the Noise Cut feature for better sound quality.
1Tune to an AM radio station then press SHIFT+SETUP.
2Use /to choose NOISECUT then press
ENTER.
3Use /to select the noise cut mode then press ENTER.
Select an effect level between 1 and 3.
Memorizing stations
You can save up to 30 station presets so that you always have easy access to your favorite stations without having to tune in manually each time.
1Tune to an AM or FM radio station.
Select mono or auto-stereo reception (FM) or the Noise Cut mode (AM) as necessary. These settings are saved along with the preset.
2Press SHIFT+SETUP and use / to choose ‘ST.MEM.’ then press ENTER.
14
3 Use / to select the station preset you want then press ENTER.
Listening to station presets
1Make sure the TUNER function is selected.
2Use the ST +/– buttons to select a station preset.
•You can also use the number buttons to do this.
Listening to other sources
You can connect auxiliary sources (TV, satellite receiver, etc.) to this unit for playback through the speaker system. See Connecting auxiliary audio components on page 33 for more on this.
•To connect a USB device to the USB terminal, see USB playback on page 25.
1Make sure that the external source (TV, satellite receiver, etc.) is switched on.
2Press LINE to select the source.
3If necessary, start playback of the source.
En
Listening to your system
Chapter 3
Listening to your system
Auto listening mode
The Auto listening mode is the simplest way to listen to any source as it was mastered: the output from the speakers mirrors the channels in the source material.
•If you set up the system for Front surround (page 10), the Front Surround modes will give the best results.
MCACC |
TUNE |
TESTTONE |
F.S.SURR SURROUND ADVANCED SOUND
• Press SURROUND to select the AUTO listening mode.1
Listening in surround sound
You can listen to stereo or multichannel
sources in surround sound.2 Surround sound is generated from stereo sources using one of the Dolby Pro Logic decoding modes.
•If you set up the system for Front surround (page 10), the Front Surround modes will give the best results.
MCACC |
TUNE |
TESTTONE |
F.S.SURR SURROUND ADVANCED SOUND
•Press SURROUND repeatedly to select a
listening mode.1
The choices that appear in the display will vary according to the type of source that’s playing.
•AUTO – Auto listening mode (see above)
•DOLBY PL (Dolby Pro Logic) – 4.1 channel surround sound (use with any two-channel source)
•MOVIE (Dolby Pro Logic II Movie) – Pro Logic II 5.1 channel surround sound, especially suited to movie sources (use with any two-channel source)
•MUSIC (Dolby Pro Logic II Music) – Pro Logic II 5.1 channel surround sound, especially suited to music sources (use with any two-channel source)
•STEREO – See Listening in stereo below
Dolby Pro Logic II Music settings
When listening in Dolby Pro Logic II Music mode, there are three settings you can adjust: Center Width, Dimension, and Panorama.
1With Dolby Pro Logic II Music mode active, press SOUND.
2Use /to select ‘C WIDTH’, ‘DIMEN.’ or
‘PANORAMA’ then press ENTER to confirm.
•C WIDTH (Center Width) – Provides a better blend of the front speakers by spreading the center channel between the front right and left speakers, making it sound wider (higher settings) or narrower (lower settings).
•DIMEN. (Dimension) – Adjusts the depth of the surround sound balance from front to back, making the sound more distant (minus settings), or more forward (positive settings).
•PANORAMA – Extends the front stereo image to include the surround speakers for a ‘wraparound' effect.
03
Español Nederlands Italiano Français Deutsch English
Note
1If the source is Dolby Digital or DTS, the corresponding indicator lights in the front panel display.
2Note that when the tuner is selected, multichannel playback is not possible.
15
En
03 Listening to your system
Using Front Stage Surround Advance
The Front Stage Surround Advance modes are effective when you are using the Front surround speaker setup as described on
• Press ADVANCED to select an Advanced Surround mode.
Press repeatedly to select ACTION,
UNPLUGED, EXPANDED, TV SURR., SPORTS, ADV.GAME, VIRTUAL or X-STEREO (Extended Stereo).
page 10.1
TOPMENU |
TUNE |
MENU |
SETUP |
|
SR |
ST |
ENTER |
ST |
HOME |
|
|
MENU |
|
RETURN |
MCACC |
TUNE |
TESTTONE |
F.S.SURR SURROUND ADVANCED SOUND
• Press F.S.SURR to select a Front Stage Surround Advance mode.
Listening in stereo
You can listen to any source — stereo or multichannel — in stereo. When playing a multichannel source, all channels are downmixed to the front left/right speakers and the subwoofer.
MCACC |
TUNE |
TESTTONE |
F.S.SURR SURROUND ADVANCED SOUND
Press repeatedly to select FOCUS5.1, WIDE5.1 or EXTRAPWR.
•FOCUS5.1 – Use to provide a rich surround sound effect directed to the center area where the left and right speakers’ sound projection converges.
•WIDE5.1 – Use to provide a surround sound effect to a wider area than
FOCUS5.1 mode.
•EXTRAPWR – Outputs stereo sound (in the case of multi-channel sources, down-mixed stereo sound) from the surround speakers for powerful stereo effect.
Using Advanced Surround
The Advanced Surround effects can be used with any multichannel or stereo source for a
variety of additional surround sound effects.1 These modes are designed to provide optimum listening effect when using the Standard surround setup described on page 10.
MCACC |
TUNE |
TESTTONE |
F.S.SURR SURROUND ADVANCED SOUND
• Press SURROUND repeatedly until STEREO shows in the display.
Listening with headphones
When headphones are connected, only the
STEREO (default) and PHONES SURROUND
(virtual surround sound for headphones) modes are available.
• With headphones connected, press ADVANCED to select PHONES SURROUND or SURROUND to select STEREO.
Listening with Acoustic Calibration EQ
You can listen to sources using the Acoustic Calibration Equalization set in Using the Auto MCACC setup for optimal surround sound on
page 10.2
1 Press SOUND and use / to select
MCACC EQ then press ENTER.
Note
1Note that when the tuner is selected, multichannel playback is not possible.
2Acoustic Calibration EQ is not available when headphones are connected.
16
En
Listening to your system |
03 |
2 Use / to select EQ ON or EQ OFF then press ENTER to confirm.
•If you select EQ OFF, equalization is set to off but speaker settings (channel delay and channel level) remain in effect.
•EQ ON is selected automatically after the Auto MCACC setup is completed.
Using the Sound Retriever
When audio data is removed during the WMA/ MP3/MPEG-4 AAC compression process, sound quality often suffers from an uneven sound image. The Sound Retriever feature employs new DSP technology that helps bring CD quality sound back to compressed 2- channel audio by restoring sound pressure and smoothing jagged artifacts left over after compression.
• While listening to a stereo source, press SOUND RETRIEVER to switch the sound retriever on or off.
Enhancing dialog
The Dialog Enhancement feature is designed to make the dialog stand out from other background sounds in a TV or movie soundtrack.
1Press SOUND and use / to select
DIALOGUE then press ENTER.
2Use / to select the amount of dialog enhancement then press ENTER to confirm.
Select between OFF, MID or MAX.
2 Use /to select the option you want to adjust and press ENTER.
The Bass/Treble, Quiet and Midnight features cannot be used at the same time.
Adjusting the bass and treble
Use the tone controls to adjust the bass and treble.
• Use / to select BASS or TREBLE then use / to adjust the tone. Press ENTER to confirm.
Quiet and Midnight modes
The Quiet listening feature reduces excessive bass or treble in a sound source.
The Midnight listening feature allows you to hear effective surround sound of movies at low volume levels.
• After pressing ENTER, the setting switches on/off.
•To cancel the Quiet or Midnight listening modes, select BASS/TRE.
Boosting the bass level
There are two bass modes you can use to enhance the bass in a source.1
1Press SOUND and use / to select
BASSMODE then press ENTER.
2Use / to adjust the sound then press
ENTER to confirm.
Select between OFF, MUSIC or CINEMA.
Español Nederlands Italiano Français Deutsch English
Using the Tone controls
You can change the tonal balance of the sound by using the tone control menu.
1 Press SOUND and use / to select
TONE then press ENTER.
Note
1 The Bass Mode is not available when headphones are connected.
17
En
04 Disc playback features
Chapter 4
Disc playback features
Important
•Many of the functions covered in this chapter apply to DVD discs, Video CDs/ Super VCDs, CDs, DivX video and WMA/ MP3/MPEG-4 AAC/JPEG discs, although the exact operation of some varies slightly with the kind of disc loaded.
•Some DVDs restrict the use of some functions (random or repeat, for example) in some or all parts of the disc. This is not a malfunction.
•When playing Video CD/Super VCDs, some of the functions are not available during PBC playback. If you want to use them, start the disc playing using a number button to select a track.
1 |
During playback, press |
(pause). |
|
2 |
Press and hold |
or |
until slow |
motion playback starts. |
|
|
Press repeatedly to change the slow motion speed (shown on-screen).
• To resume playback, press (play).2
Frame advance/frame reverse
You can advance or back up DVD discs frame- by-frame. With Video CD/Super VCDs and DivX video you can only use frame advance.
1 |
During playback, press |
(pause). |
|
2 |
Press |
or |
to reverse or |
advance a frame at a time.
• To resume playback, press (play).2
Scanning discs
You can fast-scan discs forward or backward at various different speeds.1
Playing a JPEG slideshow
After loading a disc containing JPEG pictures, press to start a slideshow from the first
• During playback, press |
or |
to start |
scanning. |
|
|
Press repeatedly to increase the scanning speed (shown on-screen).
• To resume playback, press (play).2
Playing in slow motion
You can play DVDs, Video CD/Super VCDs and DivX video at four different forward slow motion speeds. DVD discs can also be played in reverse slow motion.
folder/picture on the disc.3 The player displays the pictures in each folder in alphabetical order.
•If the disc contains WMA/MP3/MPEG-4 AAC files, playback of the slideshow and audio files repeats. During audio playback,
you can still use the skip ( |
/ |
), scan |
||
( |
/ |
) and pause ( ) functions. |
Pictures are automatically adjusted so that they fill as much of the screen as possible.
Note
1Only one speed is available for DivX video discs.
2• Depending on the disc, normal playback may automatically resume when a new chapter is reached on a DVD disc.
•For Video CDs/Super VCDs in PBC mode and WMA/MP3/MPEG-4 AAC tracks (in Scan Mode only), normal playback resumes when you reach the beginning or the end of a track.
3• The time it takes for the player to load a file increases with large file sizes.
•Discs can contain up to 299 folders and up to 648 folders and files combined.
18
En
Disc playback features |
04 |
While the slideshow is running:
Button |
What it does |
|
Pauses the slideshow (or audio); |
|
press again to restart. |
|
|
|
Jumps to the previous picture (or |
|
audio file with audio playback). |
|
|
|
Jumps to the next picture (or |
|
audio file with audio playback). |
/ / / Pauses the slideshow and rotates/flips the displayed picture (Press (play) to restart slideshow).
SHIFT+ Pauses the slideshow and zooms ZOOM the picture. Press again to toggle
between 1x, 2x and 4x zoom (Press (play) to restart slideshow).
MENU Displays the Disc Navigator
screen (see below).
Browsing DVD or Video CD/ Super VCD discs with the Disc Navigator
Use the Disc Navigator to browse through the contents of a DVD or Video CD/Super VCD disc to find the part you want to play.
1 During playback, press HOME MENU and select ‘Disc Navigator’ from the onscreen menu.
Disc Navigator
2 Select a view option.
Disc Navigator
Title
Chapter
The options available depend on the kind of |
|
|
|
English |
• Title – Titles from a DVD-Video disc. |
|
|
|
|
disc loaded and whether the disc is playing or |
|
|||
not, but include: |
|
|
|
|
• Chapter – Chapters from the current title |
|
|||
|
||||
of a DVD-Video disc. |
|
|
|
|
|
|
|
Deutsch |
|
• Time – Thumbnails from a Video CD/Super |
|
|||
• Track – Tracks from a Video CD/Super VCD |
|
|
||
disc. |
|
|
|
|
VCD disc at 10 minute intervals. |
|
|
|
|
|
|
|
|
|
• Original: Title – Original titles from a VR |
|
|
||
|
Français |
|||
mode DVD-R/-RW disc. |
|
|
|
|
mode DVD-R/-RW disc. |
|
|
|
|
• Playlist: Title – Playlist titles from a VR |
|
|
|
|
• Original: Time – Thumbnails from the |
|
|
|
|
|
|
|
|
|
Original content at 10 minute intervals. |
|
|
|
|
|
|
|
Italiano |
|
• Playlist: Time – Thumbnails from the |
|
|
|
|
|
|
|
|
|
Playlist at 10 minute intervals. |
|
|
|
|
The screen shows up to six moving thumbnail |
|
|||
images displayed one after another. To display |
|
|||
|
||||
the previous/next six thumbnails, press |
/ |
|
|
|
|
|
Nederlands |
||
. |
|
|
|
|
|
|
|
|
|
3 Select the thumbnail image for what |
|
|
|
|
you want to play. |
|
|
|
|
|
|
|
|
|
01 |
02 |
03 |
Español |
04 |
05 |
06 |
|
Disc Navigator: Title |
|
|
|
0149: -- |
|
|
|
You can use either / / / and ENTER to select a thumbnail, or the number buttons.
To select using the number buttons, enter a two-digit number then press ENTER.
19
En
04 Disc playback features
Browsing WMA, MP3, MPEG-4 AAC, DivX video and JPEG files with the Disc Navigator
Use the Disc Navigator to find a particular file or folder by filename.
1 Press HOME MENU and select ‘Disc Navigator’ from the on-screen menu.
00:00/ 00:00 |
0kbps |
Folder1
Folder2
Folder3
Folder4
2 Use / / / and ENTER to navigate.
Use / to move up and down the folder/file list.
Use to return to the parent folder.1
Use ENTER or to open a highlighted folder.
•When a JPEG file is highlighted, a thumbnail image is displayed on the right.
00:00/ 00:00 |
0kbps |
Folder2
File1
File2
File3
File4
File5
3 To play the highlighted track or DivX video file or display the highlighted JPEG file, press ENTER.
•When a WMA/MP3/MPEG-4 AAC or DivX video file is selected, playback begins from that file, and continues until the end of the folder.
•When a JPEG file is selected, a slideshow begins, starting with that file, and continues to the end of the folder.
Tip
•You can also play a JPEG slideshow while listening to WMA/MP3/MPEG-4 AAC playback. Simply select the audio file you want to listen to followed by the JPEG from which you want the slideshow to start. Playback of both the slideshow and the audio files repeats. Playback controls are effective for the JPEG slideshow only.
•To play the contents of the whole disc rather than just the current folder, exit the Disc Navigator and start playback using
the (play) button.
Using Playlists
With this feature, you can make up to three playlists of 30 files each for discs containing WMA, MP3, MPEG-4 AAC and JPEG files.
Since this unit will remember all playlists for the last ten discs you have loaded, this is useful for if you have a large number of files that you
want to organize quickly and easily.2
Programming playlists
1With the disc stopped, press HOME MENU and select ‘Disc Navigator’ from the on-screen menu.
2Select the file you want to add to the playlist.
See Browsing WMA, MP3, MPEG-4 AAC, DivX video and JPEG files with the Disc Navigator above if you don’t know how to do this.
3Press PLAY LIST 1, 2 or 3.
The file is added to the playlist you select.
4 Repeat steps 2 and 3 until you’re done.
Note
1You can also do this by going to the ‘..’ folder at the top, then pressing ENTER.
2The disc must be loaded for the files in your playlist to play back.
20
En
Disc playback features |
04 |
Tip
•To add files without the on-screen display, simply press PLAY LIST 1, 2 or 3 during normal playback of the file you want (except when a JPEG slideshow is playing at the same time as audio).
Listening to playlists
• With playback stopped, press PLAY LIST 1, 2 or 3.
During playback, PGM lights in the front panel display. If no playlist has been programmed, NO LIST shows in the display.
•If the playlist contains both JPEG and audio files, playback of the slideshow and audio files starts.
Clearing files from a playlist
1Start playback of your playlist.
2From the ‘Disc Navigator’ screen, select the file you want to remove from the playlist and press CLEAR.
Looping a section of a disc
The A-B Repeat function allows you to specify two points (A and B) within a track (CD, Video CD/Super Video CD) or title (DVD) that form a loop which is played over and over.
1 During playback, press HOME MENU and select ‘Play Mode’.
Play Mode
2Select ‘A-B Repeat’.
3Press ENTER on ‘A(Start Point)’ to set the loop start point.
4Press ENTER on ‘B(End Point)’ to set the loop end point.
After pressing ENTER, playback jumps back to the start point and plays the loop.
5To resume normal playback, select ‘Off’.
Using repeat play
In addition to various repeat play options, it’s also possible to use repeat play together with program play (see Creating a program list on page 22).
1During playback, press HOME MENU and select ‘Play Mode’.
2Select ‘Repeat’ then select a repeat play
option.1
If program play is active, select Program Repeat to repeat the program list, or Repeat Off to cancel.
•For DVD discs, select Title Repeat or
Chapter Repeat.
•For CDs and Video CD/Super VCDs, select
Disc Repeat or Track Repeat.
•For DivX video discs, select Title Repeat
(or Repeat Off).
Using random play
Use this function to play titles or chapters (DVD-Video) or tracks (CD and Video CD/Super
VCD) in a random order.2
1 During playback, press HOME MENU and select ‘Play Mode’.
Español Nederlands Italiano Français Deutsch English
Note
1You can’t use repeat play with WMA/MP3/MPEG-4 AAC discs.
2• You can set the random play option when a disc is playing or stopped. However, you can’t use random play together with program play.
•You can’t use random play with VR format DVD-R/-RW discs, WMA/MP3/MPEG-4 AAC discs, DivX video discs, or while a DVD disc menu is being displayed.
21
En
04 Disc playback features
2Select ‘Random’ then select an option.
•For DVD discs, select Random Title or
Random Chapter.
•For CDs and Video CD/Super VCDs, select On or Off to switch random play on or off.
Tip
•Use the following controls during random play:
Button |
What it does |
|
Selects a new track/title/chapter |
|
at random. |
|
|
|
Returns to the beginning of the |
|
current track/title/chapter; |
|
further presses select another |
|
random track/title/chapter. |
After pressing ENTER to select the title/ chapter/track, the step number automatically moves down one.
4 Repeat step 3 to build up a program list.
A program list can contain up to 24 steps.
•You can insert steps by just highlighting the position where you want the new step to appear and entering a title/chapter/track number.
•To delete a step, highlight it and press
CLEAR.
5 To play the program list, press (play).
Program play remains active until you turn off program play (see below), erase the program list (see below), eject the disc or switch off.
Tip
•Random play remains in effect until you select Random Off from the random play menu options.
Creating a program list
This feature lets you program the play order of titles/chapters/tracks on a disc.1
1During playback, press HOME MENU and select ‘Play Mode’.
2Select ‘Program’ then select ‘Create/Edit’ from the list of program options.
3Use / / / and ENTER to select a title, chapter or track for the current step in the program list.
•Use the following controls during program play:
Button |
What it does |
HOME Save the program list and exit MENU without starting playback.
Skip to the next step in the program list.
Other functions available from the program menu
There are a number of other options in the program menu in addition to Create/Edit.
•Playback Start – Starts playback of a saved program list
•For a DVD disc, you can add a title or a chapter.
•For a CD or Video CD/Super VCD, select a track to add to the program list.
•Playback Stop – Turns off program play, but does not erase the program list
•Program Delete – Erases the program list and turns off program play
Note
1 You can’t use Program play with VR format DVD-R/-RW discs, WMA/MP3/MPEG-4 AAC discs, DivX video discs, or while a DVD disc menu is being displayed.
22
En
Disc playback features
Searching a disc
You can search DVD discs by title or chapter number, or by time; CDs and Video CD/Super VCDs by track number or time; DivX video discs by time.
1Press HOME MENU and select ‘Play Mode’.
2Select ‘Search Mode’.
The search options that appear depend on the kind of disc loaded.
3Select a search mode.
•The disc must be playing in order to use time search.
4Use the number buttons to enter a title, chapter or track number, or a time.
•For a time search, enter the number of minutes and seconds into the currently playing title (DVD/ DivX video) or track (CD/ Video CD/Super VCD) you want playback to resume from. For example, press 4, 5, 0, 0 to have playback start from 45 minutes into the disc. For 1 hour, 20 minutes and 30 seconds, press 8, 0, 3, 0.
5Press ENTER to start playback.
Switching subtitles
Some DVD discs and DivX video discs have subtitles in one or more languages; the disc box will usually tell you which subtitle languages are available. You can switch
subtitle language during playback.1
04
• Press SHIFT+SUBTITLE repeatedly to |
English |
||||
select a subtitle option. |
|||||
|
|||||
|
• To set subtitle preferences, see Language |
|
|||
|
settings on page 30. |
|
|||
|
• See Displaying DivX subtitle files on |
|
|||
|
|||||
|
page 40 for more on DivX subtitles. |
Deutsch |
|||
|
|
|
|
||
Switching language/audio |
|||||
|
|||||
channels |
|
||||
When playing discs recorded with dialog in two |
|
||||
or more languages, or with dual-mono audio2 |
Français |
||||
• Press SHIFT+AUDIO repeatedly to select |
|||||
you can switch these during playback.3 |
|
||||
an audio language option. |
|
||||
|
• To set audio language preferences, see |
Italiano |
|||
|
Language settings on page 30. |
||||
|
|
||||
|
|
||||
|
Zooming the screen |
|
|
||
Using the zoom feature you can magnify a part |
|
||||
of the screen by a factor of 2 or 4, while |
|
Nederlands |
|||
|
|||||
watching a DVD, DivX video title or Video CD/ |
|
||||
|
|
||||
Super VCD or playing a JPEG disc. |
|
|
|||
1 During playback, use the SHIFT+ZOOM |
|
|
|||
button to select the zoom factor (Normal, 2x |
|
|
|||
|
|
||||
or 4x). |
Español |
||||
You can change the zoom factor and the |
|||||
2 Use / / / to change the zoomed |
|
||||
area. |
|
||||
zoomed area freely during playback.4 |
|
Note
1Some discs only allow you to change subtitle language from the disc menu. Press TOP MENU or MENU to access.
2Some Super VCDs have two soundtracks. With these discs you can switch between the two soundtracks as well as individual channels in each.
3Some discs only allow you to change audio language from the disc menu. Press TOP MENU or MENU to access.
4• Since DVD, Video CD/Super VCD, DivX video title and JPEG pictures have a fixed resolution, picture quality will deteriorate, especially at 4x zoom. This is not a malfunction.
•If the navigation square at the top of the screen disappears, press SHIFT+ZOOM again to display it.
23
En
04 Disc playback features
Switching camera angles
Some DVD discs feature scenes shot from two or more angles — check the disc box for details.
When a multi-angle scene is playing, a icon appears on screen (this can be switched off if you prefer — see Display settings on page 30).
• During playback (or when paused), press SHIFT+ANGLE to switch angle.
Displaying disc information
Various track, chapter and title information can be displayed on-screen during playback.
• To show/switch/hide the information displayed, press DISPLAY repeatedly.
Limited disc information also appears in the front panel display. Press DISPLAY to change the displayed information.
24
En
USB playback
Chapter 5
USB playback
Using the USB interface
It is possible to listen to two-channel audio1 and watch JPEG files using the USB interface on the front of this unit. Connect a USB mass
storage device2 as shown below.
1With the player switched on, press USB.
Make sure your TV is on and set to the correct video input.
2Connect your USB device.
The USB terminal is located on the front panel.
USB
(Type A)
USB mass storage device
Important
If a USB ERR message lights in the display, it may mean that the power requirements of the USB device are too high for this player, or that the device is incompatible. Try the following:
•Switch the player off, then on again.
•Reconnecting the USB device with the player switched off.
•Selecting to another input source (like DVD/CD), then back to USB.
•Using a dedicated AC adapter (supplied with the device) for USB power.
If this doesn’t remedy the problem, it is likely your USB device is incompatible.
Basic playback controls
The following table shows the basic controls on the remote for USB playback.
Button What it does
Starts normal playback.
Pauses/unpauses playback.
Stops playback.
3 Press (play) to start playback.
If your USB device contains JPEGs, a slideshow will start. See Playing a JPEG slideshow on page 26 for more on this.
•Make sure USB DATA is showing in the front panel display (or the system is in standby) when disconnecting.
Press to start fast reverse scanning.
Press to start fast forward scanning.
Skips to the start of the current file, then previous files.
Skips to the next file.
Note
1This includes playback of WMA/MP3/MPEG-4 AAC files (except files with copy-protection or restricted playback). It is not possible to play DivX files through the USB terminal.
2• Compatible USB devices include external magnetic hard drives, portable flash memory (particularly keydrives) and digital audio players (MP3 players) of format FAT16/32. It is not possible to connect this unit to a personal computer for USB playback.
•Pioneer cannot guarantee compatibility (operation and/or bus power) with all USB mass storage devices and assumes no responsibility for any loss of data that may occur when connected to this unit.
•With large amounts of data, it may take longer for the system to read the contents of a USB device.
05
Español Nederlands Italiano Français Deutsch English
25
En
05 USB playback
Scanning files
You can fast-scan forward or backward at various different speeds.
• During playback, press |
or |
. |
Press repeatedly to increase the scanning speed (shown on-screen).
• To resume playback, press (play).1
Button |
What it does |
MENU Displays the Navigator screen (see below).
Browsing files with the Navigator
Use the Navigator to find WMA, MP3, MPEG-4 AAC and JPEG files or folders by name.3
Playing a JPEG slideshow
Press to start a slideshow from the first
folder/picture.2 The pictures in each folder are displayed in order.
•If the device contains WMA/MP3/MPEG-4 AAC files, playback of the slideshow and audio files repeats. During audio playback,
you can still use the skip ( |
/ |
), scan |
||
( |
/ |
) and pause ( ) functions. |
Pictures are automatically adjusted so that they fill as much of the screen as possible.
While the slideshow is running:
Button |
What it does |
|
|
Pauses the slideshow (or audio); |
|
|
press again to restart. |
|
|
|
|
|
Jumps to the previous picture (or |
|
|
audio file with audio playback). |
|
|
|
|
|
Jumps to the next picture (or |
|
|
audio file with audio playback). |
|
|
||
/ / / Pauses the slideshow and |
||
|
rotates/flips the current picture |
|
|
(Press |
to restart slideshow). |
|
|
|
SHIFT+ |
Pauses the slideshow and zooms |
|
ZOOM |
the picture. Press again to toggle |
|
|
between 1x, 2x and 4x zoom |
|
|
(Press |
to restart slideshow). |
|
|
|
1 Press MENU then use / / / and
ENTER to navigate.
Use / to move up/down the folder/file list. Use to return to the parent folder.4
Use ENTER or to open a highlighted folder.
•When a JPEG file is highlighted, a thumbnail image is displayed on the right.
2 To play the highlighted track or display the highlighted JPEG file, press ENTER.
•When a WMA/MP3/MPEG-4 AAC file is selected, playback begins from that file, and continues until the end of the folder.
•When a JPEG file is selected, a slideshow begins, starting with that file, and continues to the end of the folder.
Tip
•You can also play a JPEG slideshow while listening to WMA/MP3/MPEG-4 AAC playback. Simply select the audio file you want to listen to followed by the JPEG from which you want the slideshow to start. Playback of both the slideshow and the audio files repeats. Playback controls are effective for the JPEG slideshow only.
•To play all of the contents, rather than just the current folder, exit the Navigator and
start playback using the (play) button.
Note
1With WMA/MP3/MPEG-4 AAC tracks, playback automatically resumes at the end or beginning of the track.
2• The time it takes for the player to load a file increases with large file sizes.
• USB devices can contain up to 299 folders and up to 648 folders and files combined.
3Filenames may be displayed incorrectly with some digital audio players.
4You can also do this by going to the ‘..’ folder at the top, then pressing ENTER.
26
En
Surround sound settings
Chapter 6
Surround sound settings
Using the Setup menu
From the Setup menu you can access all the
surround sound settings of the system1, including channel levels, speaker distances and dynamic range adjustment. The Auto MCACC feature (page 10) should give you the best surround sound setup. However you may find that by further adjustment of the surround sound settings you can improve the surround sound in your listening room.
1 Press SHIFT+SETUP and use / then
ENTER to choose the setting you want to adjust.
The available settings are shown in the front panel display.2
2 Use / to adjust then press ENTER to confirm and exit.
•Note that using the Auto MCACC (page 10) again overwrites the speaker settings.
Channel level setting
Set the relative channel levels from your main listening position.3
Use / to switch between channels in the following order:
•L – Front left speaker
•C – Center speaker
•R – Front right speaker
•SR – Surround right speaker
•SL – Surround left speaker
•SW – Subwoofer
The channel level range is ±10 dB.
Speaker distance setting
Specifies the distance from your listening position to your speakers.
When DISTANCE appears, press ENTER, then use / to adjust the distance, and / to switch between the following speakers:
•L – Front left speaker
•C – Center speaker
•R – Front right speaker
•SR – Surround right speaker
•SL – Surround left speaker
•SW – Subwoofer
Each speaker can be adjusted between 0.3 m and 9.0 m. The default setting is 3.0 m.
Dynamic Range Control
Specifies dynamic range adjustment to Dolby Digital or some DTS soundtracks. If low level sound or dialog seem difficult to hear properly, this can help by bringing up the low level sounds, while controlling high level peaks.
•DRC OFF (default) – No dynamic range adjustment (use when listening at higher volumes)
•DRC MID – Mid setting
•DRC HIGH – Dynamic range is reduced (loud sounds are reduced in volume while quieter sounds are increased)
Note
1There are other settings you can adjust from the Setup menu; these are explained in Improving poor FM reception on page 14 and Dimming the display on page 39.
2The setup menu is exited automatically after 5 minutes of inactivity.
3• You can’t adjust center/surround when Stereo or Virtual playback is selected (or with stereo sources using the Auto mode).
•The Channel level setting is not available when headphones are connected.
•The speaker volume can be adjusted at any time by pressing SHIFT+TEST TONE and then using / to adjust the channel levels. The test tone automatically moves from speaker to speaker in the order listed above. You should hear the test tone at the same volume from each speaker when seated in the main listening position. Press ENTER when you’re finished.
•Since the subwoofer produces ultra-low frequencies it may seem quieter than it actually is.
06
Español Nederlands Italiano Français Deutsch English
27
En
07 Video Adjust menu
Chapter 7
Video Adjust menu
Video Adjust menu
From the Video Adjust screen you can adjust settings that affect picture presentation.
1 Press HOME MENU and select ‘Video Adjust’ from the on-screen display.
Video Adjust
2 Make settings using / / / and
ENTER.
Video Adjust |
|
Sharpness |
Standard |
Brightness |
0 |
Contrast |
0 |
Gamma |
Off |
Hue |
0 |
Chroma Level |
0 |
You can adjust the following settings:
•Sharpness – Adjusts the sharpness of edges in the picture (Fine, Standard, Soft)
•Brightness – Adjusts the overall brightness (–20 to +20)
•Contrast – Adjusts the contrast between light and dark (–16 to +16)
•Gamma – Adjusts the ‘warmth’ of the picture (High, Medium, Low, Off)
•Hue – Adjusts the red/green balance (Green 9 to Red 9)
•Chroma Level – Adjusts how saturated colors appear (–9 to +9)
Adjust the Brightness, Contrast, Hue and
Chroma Level settings using /.
Brightness |
min |
max |
0 |
3 Press ENTER to return to the Video Adjust screen, or HOME MENU to exit.
28
En
Initial Settings menu
Chapter 8
Initial Settings menu
Using the Initial Settings menu
The Initial Settings menu provides audio and video output settings, parental lock settings, and display settings, among others.
If an option is grayed out it means that it cannot be changed at the current time. This is usually because a disc is playing. Stop the disc, then change the setting.
1Press DVD/CD.
2With playback stopped, press HOME MENU and select ‘Initial Settings’.
Initial Settings
3 Use / / / and ENTER to select the setting and option you want to set.
All the settings and options are explained on the following pages.1
08
Français Deutsch English
Video Output settings
Setting |
Option |
What it means |
TV Screen
(See also Screen sizes and disc formats on page 43.)
4:3 (Letter Box) |
Set if you have a conventional 4:3 TV. Widescreen movies are |
|
shown with black bars top and bottom. |
|
|
4:3 (Pan & Scan) |
Set if you have a conventional 4:3 TV. Widescreen movies are |
|
shown with the sides cropped so that the image fills the screen. |
|
|
16:9 (Wide) |
Set if you have a widescreen TV. |
|
|
16:9 (Compressed) |
Set if you have a widescreen TV. 4:3 material is shown with |
|
black bars on either side of the screen.2 |
HDMI Resolution |
1920x1080i |
Set if your TV supports 1920 x 1080 pixel interlace video. |
|
(See Connecting using |
|
|
|
1280x720p |
Set if your TV supports 1280 x 720 pixel progressive-scan video. |
||
HDMI on page 35.) |
|||
|
|
||
|
720x480p |
Set if your TV supports 720 x 480 pixel progressive-scan video. |
|
|
|
|
|
|
720x480i |
Set if your TV supports 720 x 480 pixel interlace video. |
|
|
|
|
|
HDMI Color* |
Full range RGB |
If colors are weak, this gives brighter colors and deeper black |
|
(See Connecting using |
|
(default setting for HDMI-compatible DVI devices). |
|
HDMI on page 35.) |
|
|
|
RGB |
Use this setting if colors appear overly rich on the Full Range |
||
* Default changes |
|||
|
RGB setting. |
||
depending on device |
|
||
|
|
||
connected. |
Component |
Outputs 8-bit component video format (default setting for |
|
|
|
HDMI-compatible devices). |
|
|
|
|
|
|
|
|
Note
1• In the table, the default setting is shown in bold: other settings are shown in italics.
•Some settings, such as TV Screen, Audio Language and Subtitle Language may be overridden by the DVD disc. Often these settings can also be made from the DVD disc menu.
•The HDMI Resolution and HDMI Color settings only need to be set if you connected this player to an HDMI-compatible component using the HDMI connector.
2This setting can only be used when you are connected via HDMI and have the HDMI resolution set to 1920x1080i or 1280x720p. When using this setting, only the HDMI connection is available.
Español Nederlands Italiano
29
En
08 Initial Settings menu
Setting |
Option |
What it means |
|
Component Out |
Interlace |
Set if your TV is not compatible with progressive scan video. |
|
(See also Connecting |
|
|
|
Progressive |
Set if your TV is compatible with progressive scan video (see |
||
using the component |
|||
|
your TV’s instruction manual for details). Press ENTER once |
||
video output on |
|
||
|
more to confirm (or RETURN to cancel). |
||
page 34.) |
|
||
|
Note that progressive scan video is only output from the |
||
|
|
||
|
|
component video jacks. |
|
|
|
|
|
|
|
|
Language settings
Setting |
Option |
What it means |
Audio Language |
English |
If there is an English soundtrack on the disc, it is played. |
|
|
|
|
Chinese |
If there is a Chinese soundtrack on the disc, it is played. |
|
|
|
|
Other Language |
Select to choose a language other than the ones displayed (see |
|
|
Using the language code list on page 48). |
|
|
|
Subtitle Language |
English |
If there are English subtitles on the disc they are displayed. |
|
|
|
|
Chinese |
If there are Chinese subtitles on the disc they are displayed. |
|
|
|
|
Other Language |
Select to choose a language other than the ones displayed (see |
|
|
Using the language code list on page 48). |
|
|
|
DVD Menu |
w/Subtitle Lang. |
DVD disc menus are displayed in the same language as your |
Language |
|
selected subtitle language, if possible. |
|
|
|
|
Languages as displayed |
DVD menus are displayed in the selected language, if possible. |
|
|
|
|
Other Language |
Select to choose a language other than the ones displayed (see |
|
|
Using the language code list on page 48). |
|
|
|
Subtitle Display |
On |
Subtitles are displayed in your selected subtitle language. |
|
|
|
|
Off |
Subtitles are always off by default when you play a DVD disc. |
|
|
|
|
|
|
Display settings
Setting |
Option |
What it means |
||
OSD Language |
English |
On-screen displays of the player are in English. |
||
|
|
|
|
|
|
|
|
|
On-screen displays of the player are in Chinese. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Angle Indicator |
On |
A camera icon is displayed on-screen during multi-angle |
||
|
|
|
|
scenes on a DVD disc. |
|
|
|
|
|
|
Off |
No multi-angle indication is shown. |
||
|
|
|
|
|
30
En