Pioneer GM-X354 User Manual

5 (1)

BRIDGEABLE FOUR-CHANNEL POWER AMPLIFIER

AMPLIFICATEUR DE PUISSANCE PONTABLE A QUATRE VOIES

Owner’s Manual

GM-X354

Mode d’emploi

FRANÇAIS DEUTSCH ESPAÑOL ENGLISH

NEDERLANDS ITALIANO

Contents

 

Before Using This Product ......................

2

In case of trouble ..............................................

2

WARNING ........................................................

2

Setting the Unit ..........................................

3

Gain Control ......................................................

3

Input Select Switch ............................................

3

Power Indicator ................................................

4

BFC (Beat Frequency Control) Switch ............

4

LPF (Low-Pass Filter)/HPF (High-Pass

 

Filter) Select Switch ..................................

4

Connecting the Unit ..................................

5

Connection Diagram ........................................

6

Connecting the Power Terminal ........................

7

Connecting the Speaker Output Terminals ......

7

Using the Speaker Input ....................................

8

Connecting the Speaker wires ..........................

9

Installation ................................................

11

Example of installation on the floor mat

 

or on the chassis ......................................

11

Specifications ..........................................

12

1

Before Using This Product

This product complies with the EMC Directives (89/336/EEC, 92/31/EEC) and CE Marking Directive (93/68/EEC).

Thank you for purchasing this PIONEER product. Before attempting operation, be sure to read this manual.

In case of trouble

When the unit does not operate properly, contact your dealer or the nearest authorized PIONEER Service Station.

WARNING

Always use the special red battery and ground wire [RD-223], which is sold separately. Connect the battery wire directly to the car battery positive terminal (+) and the ground wire to the car body.

Do not touch the amplifier with wet hands. Otherwise you may get an electric shock. Also, do not touch the amplifier when it is wet.

For traffic safety and to maintain safe driving conditions, keep the volume low enough so that you can still hear normal traffic sound.

Check the connections of the power supply and speakers if the fuse of the separately sold battery wire or the amplifier fuse blows. Detect the cause and solve the problem, then replace the fuse with another one of the same size and rating.

To prevent malfunction of the amplifier and speakers, the protective circuit will cut the power supply to the amplifier (sound will stop) when an abnormal condition occurs. In such a case, switch the power to the system OFF and check the connection of the power supply and speakers. Detect the cause and solve the problem.

Contact the dealer if you cannot detect the cause.

To prevent an electric shock or short-circuit during connection and installation, be sure to disconnect the negative (–) terminal of the battery beforehand.

Confirm that no parts are behind the panel when drilling a hole for installation of the amplifier. Be sure to protect all cables and important equipment such as fuel lines, brake lines and the electrical wiring from damage.

NEDERLANDS ITALIANO FRANÇAIS DEUTSCH ESPAÑOL ENGLISH

2

Setting the Unit

Gain Control

Adjusting the gain controls A and B will help match the output of the car stereo to the Pioneer amplifier. Normally, set the gain controls to the “NORMAL” position. If the output is low, even when the volume of the car stereo is turned up, turn these controls clockwise. If there is distortion when the volume of the car stereo is turned up, turn these controls counter-clockwise.

If you only use one input plug, set the gain controls for speaker outputs A and B to the same position.

When using with an RCA equipped car stereo (standard output of 500 mV), set to the NORMAL position. When using with an RCA equipped Pioneer car stereo with max. output of 4 V or more, adjust level to match the car stereo output level.

If you hear too much noise when using the speaker input terminals, turn the gain control counter-clockwise.

Input Select Switch

For two-channel input, slide this switch to the left. For four-channel input, slide this switch to the right.

3

Power Indicator

The power indicator lights when the power is switched on.

ENGLISH

BFC (Beat Frequency Control) Switch

If you hear a beat while listening to an MW/LW broadcast with your car stereo, change the BFC switch using a small standard tip screwdriver.

LPF (Low-Pass Filter)/HPF (High-Pass Filter) Select Switch

Set the LPF/HPF select switch as follows according to the type of speaker that is connected to the speaker output connector and the car stereo system:

LPF/HPF Select

Audio frequency range

Speaker

Remarks

Switch

to be output

Type

 

LPF (Left)

Very Low Frequency range

Subwoofer

Connect a subwoofer.

 

 

 

 

OFF (Center)

Full range

Full range

 

 

 

 

 

HPF (Right)

Low Frequency range to

Full range

Use if you want to cut the

 

High Frequency range

 

very low frequency range

 

 

 

because it is not necessary

 

 

 

for the speakers you are

 

 

 

using.

 

 

 

 

NEDERLANDS ITALIANO FRANÇAIS DEUTSCH ESPAÑOL

4

Connecting the Unit

CAUTION

Disconnect the negative (–) terminal of the battery to avoid the risk of short-circuit and damage to the unit.

Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around it where they lie against metal parts.

Do not route wires where they will get hot, for example where the heater will blow over them. If the insulation heats up, it may become damaged, resulting in a short-circuit through the vehicle body.

To prevent damage

Do not ground the speaker wire directly or connect a negative (–) lead wire for several speakers.

This unit is for vehicles with a 12-volt battery and negative grounding. Before installing it in a recreational vehicle, truck or bus, check the battery voltage.

If the car stereo is kept on for a long time while the engine is at rest or idling, the battery may go dead. Turn the car stereo off when the engine is at rest or idling.

If the system remote control wire of the amplifier is connected to the power terminal through the ignition switch (12 V DC), the amplifier will always be on when the ignition is on— regardless of whether the car stereo is on or off. Because of this, the battery could go dead if the engine is at rest or idling.

Make sure that wires will not interfere with moving parts of the vehicle, such as the gearshift, handbrake or seat sliding mechanism.

Do not shorten any wires. Otherwise the protection circuit may fail to work when it should.

Never feed power to other equipment by cutting the insulation of the power supply wire to tap from the wire. The current capacity of the wire will be exceeded, causing overheating.

Speakers to be connected to the amplifier should conform with the standards listed below. If they do not conform, they may catch fire, emit smoke or become damaged. The speaker impedance must be 2 to 8 ohms. But in case of two-channel and other bridge connections, the speaker impedance must be 4 to 8 ohms.

Install and route the separately sold battery wire as far away as possible from the speaker wires. Install and route the separately sold battery wire, ground wire, speaker wires and the amplifier as far away as possible from the antenna, antenna cable and tuner.

Cords for this product and those for other products may be different colors even if they have the same function. When connecting this product to another product, refer to the supplied Installation manuals of both products and connect cords that have the same function.

Speaker Channel

Speaker Type

Power

Four-channel

Subwoofer

Nominal input: Min. 45 W

 

 

Other than subwoofer

Max. input: Min. 70 W

 

 

 

 

Two-channel

Subwoofer

Nominal input: Min. 125 W

 

 

Other than subwoofer

Max. input: Min. 140 W

 

 

 

 

Three-channel

Subwoofer

Nominal input: Min. 45 W

 

 

 

Speaker output A

Other than subwoofer

Max. input: Min. 70 W

 

 

 

Three-channel

Subwoofer

Nominal input: Min. 125 W

 

 

 

Speaker output B

Other than subwoofer

Max. input: Min. 140 W

 

 

 

5

Connection Diagram

 

 

Fuse (30 A)

Grommet

 

 

 

 

 

 

 

 

 

 

 

 

 

Special red battery wire [RD-223] (sold separately)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

After making all other connections at the amplifier,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

connect the battery wire terminal of the amplifier to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the positive (+) terminal of the battery.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fuse (30 A)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ground wire (Black) [RD-223] (sold separately)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Connect to metal body or chassis.

RCA input

Connecting wires with RCA pin plugs (sold separately).

External Output

If only one input plug is used, do not connect anything to RCA input jack B.

Amplifier with RCA input jacks

Car stereo with RCA output jacks

Speaker input terminal

See the “Using the Speaker Input”

section.

Front side

RCA output jack

RCA input jack B

RCA input jack A

Fuse (25 A)

Speaker output terminal See the “Connecting the Speaker wires” section for speaker connection instructions.

Connecting wires with RCA pin plugs (sold separately).

Back side

System remote control wire (sold separately)

Connect the male terminal of this wire to the system remote control terminal of the car stereo (SYSTEM REMOTE CONTROL). The female terminal can be connected to the auto-antenna relay control terminal. If the car stereo does not have a system remote control terminal, connect the male terminal to the power terminal through the ignition switch.

NEDERLANDS ITALIANO FRANÇAIS DEUTSCH ESPAÑOL ENGLISH

6

Connecting the Unit

Connecting the Power Terminal

Always use the special red battery and ground wire [RD-223], which is sold separately. Connect the battery wire directly to the car battery positive terminal (+) and the ground wire to the car body.

1.Pass the battery wire from the engine compartment to the interior of the vehicle.

After making all other connections to the amplifier, connect the battery wire terminal of the amplifier to the positive (+) terminal of the battery.

Fuse (30 A) Engine

 

Interior of

compart-

the vehicle

ment

 

 

 

Fuse (30 A)

Drill a 14 mm

Positive terminal

hole into the

Insert the O-ring rubber

vehicle body.

 

 

grommet into the vehicle

 

 

body.

 

 

2.Twist the battery wire, ground wire and system remote control wire.

Twist

3.Attach lugs to wire ends. Lugs not supplied.

• Use pliers, etc., to crimp lugs to wires.

Lug

Ground wire

Lug

Battery wire

4.Connect the wires to the terminal.

Fix the wires securely with the terminal screws.

 

GND terminal

Power terminal

System remote

 

control terminal

 

System remote

 

control wire

 

Ground wire

Battery wire

Connecting the Speaker Output

Terminals

1.Expose the end of the speaker wires using nippers or a cutter by about 10 mm and twist.

Twist

10 mm

2.Attach lugs to speaker wire ends. Lugs not supplied.

• Use pliers, etc., to crimp lugs to wires.

Lug

Speaker wire

7

3.Connect the speaker wires to the speaker output terminals.

Connect the speaker wires, passing them through the terminal cover.

Fix the speaker wires securely with the terminal screws.

Terminal screw

Terminal cover

Speaker output terminal

Speaker wire

4. Push on the terminal cover.

Using the Speaker Input

Connect the car stereo speaker output wires to the amplifier using the supplied speaker input connector.

Do not connect both the RCA input and the speaker input at the same time.

7Connections when using the speaker input

Car Stereo

Speaker output

White/black:

Gray/black:

Left

Right

White:

Gray:

Left +

Right +

Speaker input connector

To speaker input terminal of this unit.

NEDERLANDS ITALIANO FRANÇAIS DEUTSCH ESPAÑOL ENGLISH

8

Connecting the Unit

Connecting the Speaker wires

The speaker output mode can be four-channel, three-channel (stereo + mono) or two-channel (stereo, mono). Connect the speaker leads to suit the mode according to the figures shown below.

When either the RCA input or the speaker input is connected, RCA output becomes functional. Do not connect both the RCA input and the speaker input at the same time.

Four-channel mode

Input Select Switch

For two-channel input, slide this switch to the left. For four-channel input, slide this switch to the right.

Speaker input

Speaker input

terminal A

terminal B

+≠≠+

+≠≠+

Speaker input connector

(Left) Speaker out A (Right)

Speaker output terminal

(Right) Speaker out B (Left)

Three-channel mode

Input Select Switch

For two-channel input, slide this switch to the left. For four-channel input, slide this switch to the right.

Speaker input

Speaker input

terminal A

terminal B

+≠≠+

+

Speaker input

 

connector

 

(Left) Speaker out A (Right)

Speaker output terminal

Speaker out B (Mono)

9

Two-channel mode (Stereo)

Input Select Switch

Slide this switch to the left.

Speaker input

Speaker (Left)

terminal A

 

 

≠+

 

Speaker output

 

terminal

 

+≠

Speaker input

Speaker (Right)

connector

 

Two-channel mode (Mono)

Input Select Switch

Slide this switch to the left.

Speaker input

Speaker (Mono)

terminal A

 

+

 

Speaker output

 

terminal

+

Speaker input

Speaker (Mono)

connector

 

NEDERLANDS ITALIANO FRANÇAIS DEUTSCH ESPAÑOL ENGLISH

10

Installation

CAUTION

• Do not install in:

—Places where it could injure the driver or passengers if the vehicle stops suddenly.

—Places where it may interfere with the driver, such as on the floor in front of the driver’s seat.

Make sure that wires are not caught in the sliding mechanism of the seats, resulting in a short-cir- cuit.

Confirm that no parts are behind the panel when drilling a hole for installation of the amplifier. Protect all cables and important equipment such as fuel lines, brake lines and electrical wiring from damage.

Install tapping screws in such a way that the screw tip does not touch any wire. This is important to prevent wires from being cut by vibration of the car, which can result in fire.

To prevent electric shock, do not install the amplifier in places where it might come in contact with liquids.

To ensure proper installation, use the supplied parts in the manner specified. If any parts other than the supplied ones are used, they may damage internal parts of the amplifier, or they may become loose causing the amplifier to shut down.

To prevent malfunction

To ensure proper heat dissipation of the amplifier, be sure of the following during installation.

—Allow adequate space above the amplifier for proper ventilation.

—Do not cover the amplifier with a floor mat or carpet.

Do not install the amplifier near a door where it may get wet.

Do not install the amplifier on unstable places such as the spare tire board.

The best location for installation differs with the car model and installation location. Secure the amplifier at a sufficiently rigid location.

Make temporary connections first and check that the amplifier and the system operate properly.

After installing the amplifier, confirm that the spare tire, jack and tools can be easily removed.

Example of installation on the floor mat or on the chassis

1.Place the amplifier where it is to be

installed. Insert the supplied tapping screws (4 × 18 mm) into the screw holes. Push on the screws with a screwdriver so they make marks where the installation holes are to be located.

2.Drill 2.5 mm diameter holes at the point marked, and install the amplifier, either on the carpet or directly to the chassis.

Tapping-screws (4 × 18 mm)

Floor mat or chassis

Drill a 2.5 mm diameter hole

11

Specifications

Power source ..........................................................................................................

14.4 V DC (10.8 — 15.1 V allowable)

Grounding system ..........................................................................................................................................

Negative type

Current consumption ....................................................................................................

18.1 A (at continuous power, 4 )

Average current drawn* ........................................................................................................

6.6 A (4 for four channels)

 

9.0 A (4 for two channels)

Fuse ..............................................................................................................................................................................

25 A

Dimensions ......................................................................................................................

279 (W) × 58 (H) × 237 (D) mm

Weight ....................................................................................................................

3.6 kg (Leads for wiring not included)

Maximum power output ....................................................................................................................

70 W × 4 / 140 W × 2

Continuous power output ........................................................................

45 W × 4 / 100 W × 2 (DIN45324, +B=14.4 V)

Load impedance ..........................................................................................................................

4 (2 — 8 allowable)

 

(Bridge connection: 4 — 8 allowable)

Frequency response ..........................................................................................................

10 — 50,000 Hz (+0 dB, –1 dB)

Signal-to-noise ratio ....................................................................................................................

100 dB (IEC-A network)

Distortion ........................................................................................................................................

0.008% (10 W, 1 kHz)

Separation ......................................................................................................................................................

65 dB (1 kHz)

Low pass filter ..............................................................................................................................

Cut off frequency: 80 Hz

 

Cut off slope: –12 dB/oct

High pass filter ............................................................................................................................

Cut off frequency: 80 Hz

 

Cut off slope: –12 dB/oct

Maximum input level/impedance ..................................................................................

RCA: 6.5 V/22 k(0.4 — 6.5 V)

 

Speaker: 26 V/40 k(1.6 — 26 V)

Note:

Specifications and the design are subject to possible modification without notice due to improvements.

*Average current drawn

The average current drawn is nearly the maximum current drawn by this unit when an audio signal is input. Use this value when working out total current drawn by multiple power amplifiers.

NEDERLANDS ITALIANO FRANÇAIS DEUTSCH ESPAÑOL ENGLISH

12

Contenido

 

Antes de usar este producto ....................

2

En caso de desperfectos ....................................

2

ADVERTENCIA ..............................................

2

Ajuste de esta unidad ..............................

3

Control de ganancia ..........................................

3

Interruptor de selección de entrada ..................

3

Indicador de alimentación ................................

4

Interruptor BFC (Control de la frecuencia de

 

batido) ........................................................

4

Interruptor de selección LPF (Filtro de paso

 

bajo)/HPF (Filtro de paso alto) ..................

4

Conexión de la unidad ..............................

5

Diagrama de conexión ......................................

6

Conexión del terminal de alimentación ............

7

Conexión del terminal de salida de altavoz ......

7

Uso de la entrada de altavoz ..............................

8

Conexión de los cables de altavoces ................

9

Instalación ................................................

11

Ejemplo de instalación en la alfombra del

 

piso o en el chasis ....................................

11

Especificaciones ....................................

12

1

Antes de usar este producto

Este producto cumple con las Directivas EMC (89/336/CEE, 92/31/CEE) y Directiva de Marcación CE (93/68/CEE).

Muchas gracias por la adquisición de este producto PIONEER. Antes de tratar de operarlo, lea atentamente este manual.

En caso de desperfectos

Si esta unidad no funciona correctamente, póngase en contacto con su distribuidor o con el Centro de Servicio PIONEER autorizado más cercano.

ADVERTENCIA

Siempre utilice el cable de batería rojo especial y el cable de tierra [RD-223], vendidos separadamente. Conecte el cable de batería directamente al terminal positivo de la batería del vehículo (+) y el cable de tierra a la carrocería del vehículo.

No toque en el amplificador con las manos mojadas. Caso contrario, usted puede llevar un choque eléctrico. Igualmente, no toque en el amplificador cuando esté mojado.

Para seguridad del tráfico y para mantener condiciones de conducción seguras, mantenga el volumen suficientemente bajo de manera que aun se pueda escuchar el sonido del tráfico normal.

Verifique las conexiones del suministro de energía y altavoces para ver si el fusible del cable de batería vendido separadamente o el fusible del amplificador se queman. Detecte la causa y solucione el problema, y reemplace el fusible con un otro del mismo tamaño y régimen.

Para evitar mal funcionamiento del amplificador y altavoces, el circuito de protección cortará la alimentación al amplificador (el sonido se detendrá) cuando se produzca una situación anormal. En tal caso, apague el sistema y verifique la conexión de la alimentación y altavoces. Detecte la causa y resuelva el problema.

Contacte a su distribuidor si no puede detectar la causa.

Para evitar choques eléctricos o cortocircuitors durante la conexión e instalación, asegúrese de desconectar el terminal negativo (–) de la batería antes de proceder.

Confirme que ninguna parte quede detrás del panel, cuando perfore un orificio para la instalación del amplificador. Asegúrese de proteger todos los cables y equipos importantes, tales como líneas de combustibles, líneas de frenos y el cableado eléctrico.

NEDERLANDS ITALIANO FRANÇAIS DEUTSCH ESPAÑOL ENGLISH

2

Ajuste de esta unidad

Control de ganancia

El ajuste de los controles de ganancia A y B le ayuda a igualar la salida del equipo estéreo para automóvil al amplificador Pioneer. Normalmente, ajuste los controles de ganancia a la posición “NORMAL”. Si la potencia de salida está baja aún cuando se aumenta el volumen del equipo estéreo del automóvil, gire esos controles a la derecha. Si se produce distorsión cuando se aumenta el volumen del equipo estéreo de automóvil, gire los controles a la izquierda.

Si se usa solamente un enchufe de entrada, ajuste los controles de ganancia para las salidas de altavoz A y B a la misma posición.

Cuando se usa un estéreo de automóvil equipado con RCA (salida estándar de 500 mV), ajuste a la posición NORMAL. Cuando use con un estéreo de automóvil Pioneer equipado con RCA con una salida máxima de 4 V o más, ajuste el nivel para adecuarse al nivel de salida del estéreo del automóvil.

Si se oye ruido excesivo cuando se usan los terminales de entrada de altavoz, gire el control de nivel a la izquierda.

Interruptor de selección de entrada

Para la entrada de dos canales, deslice este interruptor hacia la izquierda. Para la entrada de cuatro canales, deslice este interruptor hacia la derecha.

3

Indicador de alimentación

El indicador de alimentación se ilumina cuando la unidad se encuentra activada.

Interruptor BFC (Control de la frecuencia de batido)

Si escucha sonidos de batido mientras está recibiendo una emisora de MW/LW con su estéreo de automóvil, cambie el interruptor BFC usando un destornillador pequeño.

Interruptor de selección LPF (Filtro de paso bajo)/HPF (Filtro de paso alto)

Ajuste el interruptor de selección LPF/HPF de la manera siguiente, de acuerdo al tipo de altavoz que se encuentra conectado al conector de salida de altavoz y al sistema estéreo de automóvil:

Interruptor de

Gama de frecuencia

Tipo de

Observaciones

selección LPF/HPF

de audio a ser generada

altavoz

 

LPF (izquierda)

Gama de frecuencia

Altavoz de

Conecte a un altavoz de

 

muy baja

graves

graves secundario.

 

 

secundario

 

 

 

 

 

OFF (central)

Gama completa

Gama completa

 

 

 

 

 

HPF (derecha)

Gama de frecuencia

Gama completa

Utilice si desea cortar la

 

baja a gama de

 

gama de frecuencia muy

 

frecuencia alta

 

baja debido a que no es

 

 

 

necesaria para el altavoz

 

 

 

que está usando.

 

 

 

 

NEDERLANDS ITALIANO FRANÇAIS DEUTSCH ESPAÑOL ENGLISH

4

Conexión de la unidad

PRECAUCION

Quite el terminal negativo (–) de la batería para evitar riesgo de cortocircuitos y daño a la unidad.

Asegure el alambrado con abrazaderas de cable o cinta adhesiva. Para proteger el alambrado, envuelva cinta adhesiva alrededor de ellos en donde contacta con partes metálicas.

No tienda cables por donde puedan calentarse, por ejemplo donde el calentador sople sobre ellos. Si la aislación se calienta, podría resultar dañada, resultando en cortocircuito a través de la carrocería del vehículo.

Para prevenir de daños

No conecte a tierra (masa) el cable del altavoz directamente ni conecte un cable negativo (–) a varios altavoces.

Esta unidad es para vehículos con una batería de 12 voltios y terminal negativo a tierra. Antes de instalar en un vehículo de recreación, camión u ómnibus, verifique el voltaje de la batería.

Si el sistema estereofónico del coche está funcionando por un largo período de tiempo mientras el motor permanece inactivo o en marcha al ralentí, la batería puede agotarse. Apague el estéreo de automóvil cuando el motor se encuentre funcionando en marcha al ralenté o permanece in activo.

Si el cable del control remoto de sistema del amplificador se conecta al terminal de alimentación a través del interruptor de encendido (12 V de CC), el amplificador estará siempre activado cuando el encendido está activado, sin considerar de si el estéreo de automóvil se encuentra activado o desactivado. Debido a esto, la batería puede agotarse si deja el motor funcionando en marcha al ralentí o permanece inactivo.

Asegúrese que los alambres no interfieran con partes móviles del vehículo como la palanca de cambios, el freno de mano o el mecanismo de deslizamiento de los asientos.

No corte ningún cable. De otra manera, el circuito de protección podría no funcionar cuando debiera.

Nunca alimente otro equipo cortando la aislación del cable de alimentación y conectándolo al cable. La capacidad de corriente del cable será excedida, causando sobrecalentamiento.

Los altavoces a ser conectados al amplificador deben estar conforme con las normas listadas debajo. Si no cumplen con las normas, pueden combustionar, emitir humos o dañarse. El impedimiento altavoz debe estar de 2 a 8 ohms, pero en caso de que dos canales y otros puentes contecten, el impedimiento de altavoz debe ester de 4 a 8 ohms.

Instale y coloque el cable de batería vendido separadamente lo más alejado posible de los cables de los altavoces. Instale y coloque el cable de batería y cable de tierra vendidos separadamente, los cables de los altavoces, y el amplificador lo más alejados posible de la antena, cable de antena y sintonizador.

Los cables para esta unidad y aquéllas para las unidades pueden ser de colores diferentes aun si tienen la misma función. Cuando se conecta esta unidad a otra, refiérase a los manuales de instalación de ambas unidades y conecte los cables que tienen la misma función.

Canal de altavoces

Tipo de altavoz

Alimentación

Cuatro canales

Altavoz de graves secundario

Entrada nominal: 45 W mín.

 

 

Diferente a un altavoz de graves secundario

Entrada máxima: 70 W mín.

 

 

 

 

Dos canales

Altavoz de graves secundario

Entrada nominal: 125 W mín.

 

 

Diferente a un altavoz de graves secundario

Entrada máxima: 140 W mín.

 

 

 

 

Salida de altavoz A

Altavoz de graves secundario

Entrada nominal: 45 W mín.

 

 

 

de tres canales

Diferente a un altavoz de graves secundario

Entrada máxima: 70 W mín.

 

 

 

Salida de altavoz B

Altavoz de graves secundario

Entrada nominal: 125 W mín.

 

 

 

de tres canales

Diferente a un altavoz de graves secundario

Entrada máxima: 140 W mín.

 

 

 

5

Pioneer GM-X354 User Manual

Diagrama de conexión

 

Fusible (30 A)

 

 

 

 

Cable de batería rojo especial [RD-223]

Ojal

 

(en venta por separado)

 

 

 

Después de realizar todas las conexiones al amplificador,

 

 

conecte el terminal del conductor de batería del amplificador

 

Fusible (30 A)

al terminal positivo (+) de la batería.

 

 

 

 

 

 

Cable de puesta a tierra (negro) [RD-223]

 

 

(en venta por separado)

 

 

 

Conecte a una carrocería metálica o chasis.

 

 

Entrada RCA

Amplificador con

 

 

tomas con conector

 

 

 

 

Conexión de cables con los enchufes de conector

de entrada RCA

 

 

 

RCA (en venta por separado).

 

 

 

 

Estéreo de automóvil

 

 

 

con tomas con

 

Salida externa

conector de salida

 

Si se usa solamente un enchufe de entra-

RCA

 

da, no conecte nada a la toma de entrada

 

 

RCA B.

 

 

Lado delantero

Tomas de conector de salida RCA

Terminal de entrada de altavoz

Vea la sección “Uso de la entrada de altavoz”.

Tomas de conector de entrada RCA B

Tomas de conector de entrada RCA A

 

Conexión de cables con los enchufes de

Lado trasero

conector RCA (en venta por separado).

 

Fusible (25 A)

Terminal de salida de altavoz Vea la sección “Conexión de los cables de altavoces” para las instrucciones de conexión del altavoz.

Cable del control remoto del sistema (en venta por separado) Conecte el terminal macho de este hilo al terminal de control remoto de sistema del equipo estéreo para automóvil (SYSTEM REMOTE CONTROL). El terminal hembra puede ser conectado al terminal de control del relé de antena. Si el estéreo de automóvil no tiene un terminal de control remoto del sistema, conecte el terminal macho al terminal de alimentación a través del interruptor de encendido.

NEDERLANDS ITALIANO FRANÇAIS DEUTSCH ESPAÑOL ENGLISH

6

Conexión de la unidad

Conexión del terminal de alimentación

Siempre utilice el cable de batería rojo especial y el cable de tierra [RD-223], vendidos separadamente. Conecte el cable de batería directamente al terminal positivo de la batería del vehículo (+) y el cable de tierra a la carrocería del vehículo.

1.Pase el cable de batería desde el compartimiento del motor al interior del vehículo.

Luego de hacer todas las otras conexiones al amplificador, conecte el terminal del conductor de batería del amplificador al terminal positivo (+) de la bateria.

 

 

 

 

 

 

 

 

 

Comparti-

 

Fusible (30 A) miento del Interior del

 

 

 

 

 

 

 

 

 

motor

 

 

 

vehículo

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fusible (30 A)

Perfore un orifi-

Terminal positivo

cio de 14 mm en

Inserte el ojal de caucho

la carrocería del

de la junta tórica en la

vehículo.

 

 

 

 

 

 

 

corrocería del vehículo.

2.Tuerza el cable de batería, cable de puesta a tierra y cable de control remoto del sistema.

Tuérzala

3.Fije las orejetas a los extremos de los cables. Orejetas no suministrados.

Utilice alicates, etc. para plegar las orejetas a los cables.

Orejeta

Cable de puesta a tierra

Orejeta

Cable de batería

4.Conecte los cables al terminal.

Fijar los cables firmemente utilizando los tornillos para terminales.

Terminal GND

Terminal

POWER Terminal de control remoto del sistema

Cable del control remoto del sistema

Cable de puesta

a tierra

Cable de batería

Conexión del terminal de salida de altavoz

1.Desnude la extremidad de los cables de altavoces utilizando alicates o una tajadera por aproximadamente 10 mm y tuérzala.

Tuérzala

10 mm

2.Fije las orejetas a los extremos de los cables de altavoz. Orejetas no suministrados.

Utilice alicates, etc. para plegar las orejetas a los cables.

Orejeta

Cable de altavoz

7

3.Conecte los cables de altavoz al terminal de salida de altavoz.

Conecte los hilos de altavoz, pasándolos a través de la cubierta de los terminales.

Fije los cables firmemente utilizando los tornillos para terminales.

Torrillo de terminal

Cubierta de los

terminales

Terminal de salida de altavoz

Cable de altavoz

4.Empuje la cubierta de los terminales.

Uso de la entrada de altavoz

Conecte los hilos de la salida de altavoz del estéreo de automóvil al amplificador usando el conector de entrada de altavoz suministrado.

No poder conectar tanto la entrada de RCA y la entrada de altavoz al mismo tiempo.

7Conexiones cuando se usa la entrada de altavoz

Estéreo de automóvil

Salida de altavoz

Blanco/negro:

Gris/negro:

Izquierda

Derecha

Blanco:

Gris:

Izquierda +

Derecha +

Conector de entrada de altavoz Al terminal de entrada de altavoz de esta unidad.

NEDERLANDS ITALIANO FRANÇAIS DEUTSCH ESPAÑOL ENGLISH

8

Conexión de la unidad

Conexión de los cables de altavoces

El modo de salida de altavoz puede ser de cuatro canales, tres canales (estéreo + mono) o dos canales (estéreo, mono). Conecte los cables de altavoz para ajustarse al modo según los diagramas mostrados abajo.

Cuando la entrada de RCA o la entrada de altavoz está conectada, la salida de RCA viene funcionada. No poder conectar tanto la entrada de RCA y la entrada de altavoz al mismo tiempo.

Modo de cuatro canales

Interruptor de selección de entrada

Para la entrada de dos canales, deslice este interruptor hacia la izquierda. Para la entrada de cuatro canales, deslice este interruptor hacia la derecha.

Terminal de entrada

Terminal de entrada

de altavoz A

de altavoz B

+≠≠+

+≠≠+

Conector de entrada de altavoz

(Izquierdo)

Salida de altavoz A (Derecho)

Terminal de salida de altavoz

(Derecho)

Salida de altavoz B (Izquierdo)

Modo de tres canales

Interruptor de selección de entrada

Para la entrada de dos canales, deslice este interruptor hacia la izquierda. Para la entrada de cuatro canales, deslice este interruptor hacia la derecha.

Terminal de entrada

Terminal de entrada

de altavoz A

de altavoz B

+≠≠+

+

Conector de entrada de altavoz

(Izquierdo)

Salida de altavoz A (Derecho)

Terminal de salida de altavoz

Salida de altavoz B (Mono)

9

Modo de dos canales (estéreo)

Interruptor de selección de entrada

Deslice este interruptor hacia la izquierda.

Terminal de entrada de altavoz A

≠+

+≠

Conector de entrada de altavoz

Modo de dos canales (mono)

Interruptor de selección de entrada

Deslice este interruptor hacia la izquierda.

Terminal de entrada de altavoz A

+

+

Conector de entrada de altavoz

Altavoz (Izquierdo)

Terminal de salida de altavoz

Altavoz (Derecho)

Altavoz (Mono)

Terminal de salida de altavoz

Altavoz (Mono)

NEDERLANDS ITALIANO FRANÇAIS DEUTSCH ESPAÑOL ENGLISH

10

Loading...
+ 53 hidden pages