AMPLIFIER MANUAL
MANUEL DE L’AMPLIFICATEUR
Models: Ti1500.1, Ti2500.1
Ti600.4, Ti800.4
Features
•24dB Variable Low Pass and Subsonic Crossovers (Ti2500.1, Ti1500.1)
•18dB Variable High and Low Pass Crossovers (Ti800.4, Ti600.4)
•Crossovers feature 41 Detents for Exact Frequency Selection
•Audiophile Bi-Polar Output Transistors (Ti800.4, Ti600.4)
•High Efficiency Class D Topology (Ti2500.1, Ti1500.1)
•Massive Unregulated Power Supplies featuring Hand Wound Transformers
•Power Output Peak Indicators
•1/0 Gauge Direct Insert Power Terminals
•LPL44 - Low Pass Level Control Ready
•RMD -Remote Monitoring Display Port
•Advanced Thermal and Protection Circuitry
© 2010 Phoenix Gold • www.phoenixgold.com
phoenix gold ti amp manual.indd 1 |
|
|
3/2/10 11:20:39 AM |
|
|
Amplifier Owner’s Manual
SPECIFICATIONS
MONOBLOCK SPECIFICATIONS
Frequency Response: |
± 1dB from 20Hz to 300Hz |
Signal to Noise Ratio: |
>90dB |
Subsonic and Low Pass Crossovers: |
24dB per octave |
Low Pass Crossover Range: |
30Hz to 300Hz |
Subsonic Crossover Range: |
10Hz to 55Hz |
Bass Boost @ 45Hz: |
0 to +18dB |
Low Level Input Range: |
200 millivolts to 8 volts |
Lowest Recommend Load: |
1 ohm |
Typical Efficiency: |
80% |
Damping Factor: |
Greater than 200 |
Ti1500.1 |
|
Ti2500.1 |
|
Dynamic Power 14.4Vdc >1% THD |
1100 x 1 @ 2 ohm |
Dynamic Power 14.4Vdc >1% THD |
1500 x 1 @ 2 ohm |
|
1500 x 1 @ 1 ohm |
|
2500 x 1 @ 1 ohm |
RMS Power 14.4Vdc ≤ 1% THD |
900 x 1 @ 2 ohm |
RMS Power 14.4Vdc ≤ 1% THD |
1100 x 1 @ 2 ohm |
|
1250 x 1 @ 1 ohm |
|
1650 x 1 @ 1 ohm |
Recommended Fuse Size: |
100A |
Recommended Fuse Size: |
200A |
Minimum Power/Ground Wire Size: |
4 Gauge |
Minimum Power/Ground Wire Size: |
1/0 Gauge |
Dimensions: |
16.85” L x 9.8” W x 2.5” H |
Dimensions: |
20.4” L x 9.8” W x 2.5” H |
|
428mm x 252mm x 62mm |
|
518mm x 252mm x 62mm |
FOUR CHANNEL SPECIFICATIONS
Frequency Response: |
± 1dB from 20Hz to 20kHz |
Signal to Noise Ratio: |
>110dB |
High and Low Pass Crossovers: |
18dB per Octave |
Low Pass Crossover Range: |
40Hz to 400Hz |
High Pass Crossover Range: |
20Hz to 400Hz |
Bass Boost @ 45Hz: |
0 to +18dB |
Low Level Input Range: |
200 millivolts to 8 volts |
Lowest Recommend Load: |
4 ohm Bridged or 2 ohm Stereo |
Typical Efficiency: |
50% |
Damping Factor |
Greater than 200 |
Ti600.4 |
|
|
|
Ti800.4 |
|
|
Dynamic Power 14.4Vdc >1% THD |
100 x 4 @ |
4 ohm Stereo |
Dynamic Power 14.4Vdc >1% THD |
125 x 4 @ 4 ohm Stereo |
||
|
150 x 4 @ |
2 ohm Stereo |
|
200 x 4 @ 2 ohm Stereo |
||
|
300 x 2 |
@ |
4 ohm Bridged |
|
400 x 2 @ 4 ohm Bridged |
|
RMS Power 14.4Vdc ≤1% THD |
90 x 4 @ 4 ohm Stereo |
RMS Power 14.4Vdc ≤1% THD |
115 x 4 |
@ 4 ohm Stereo |
||
|
120 x 4 |
@ |
2 ohm Stereo |
|
150 x 4 |
@ 2 ohm Stereo |
|
240 x 2 |
@ |
4 ohm Bridged |
|
300 x 2 |
@ 4 ohm Bridged |
Recommended Fuse Size: |
80A |
|
|
Recommended Fuse Size: |
100A |
|
Minimum Power/Ground Wire Size: |
4 Gauge |
|
Minimum Power/Ground Wire Size: |
4 Gauge |
||
Dimensions: |
16.85” L x 9.8” W x 2.5” H |
Dimensions: |
20.4” L x 9.8” W x 2.5” H |
|||
|
428mm x 252mm x 62mm |
|
518mm x 252mm x 62mm |
© 2010 Phoenix Gold • www.phoenixgold.com
phoenix gold ti amp manual.indd 2 |
|
|
3/2/10 11:20:39 AM |
|
|
Amplifier Owner’s Manual
TI2500.1 - TI1500.1
MONOBLOCK POWER AMPLIFIER
INPUT
Connect preamp signal cables from the head unit to these terminals.
OUTPUT
Provides a full range signal for an additional amplifier. There is no signal loss if using this output.
CROSSOVER FREQUENCY
Controls the lowpass crossover point for the speaker outputs.
BASS BOOST
Variable bass boost from 0 to +18dB @ 45 Hz.
LOW PASS LEVEL CONTROL (LPL)
This port is for connecting the optional remote level control (LPL44). This allows up to 20dB of volume adjustment. This is not a bass boost, it controls the level of the low pass signal.
REMOTE MONITORING DISPLAY (RMD)
Connect optional RMD Voltage Display to this port
LEVEL
Used to reach maximum amplifier power with a wide variety of headunits.
SUBSONIC CROSSOVER FREQUENCY
Controls the highpass crossover point for the speaker outputs to eliminate extreme low frequencies.
PEAK INDICATOR
Lights when the amplifier reaches near maximum output. Under normal operation the peak indicator should be flashing during the peaks of the music. Peak indicator should not stay lit for long periods of time (more than 2 or 3 seconds), if this is the case you need to reduce system volume or level of the amplifier.
PROTECT INDICATOR
Lights red if there is a problem with the audio system. For example, speaker wire is pinched/shorted together or the amplifier is running too low of an impedance.
12V+
This must be connected to the fused positive terminal (+12V) of the car’s battery. The fuse must be located within 18 inches of the battery.
REMOTE
This must be connected to switched +12V, usually a trigger wire coming from the head unit or ignition.
GND
This must be connected to the negative terminal of the car’s battery or bolted to a clean, unpainted part of the chassis of the vehicle.
SPEAKER OUTPUTS
Used to connect the amplifier to speakers. Minimum impedance is 1 ohm.
© 2010 Phoenix Gold • www.phoenixgold.com
phoenix gold ti amp manual.indd 3 |
|
|
3/2/10 11:20:40 AM |
|
|
Amplifier Owner’s Manual
TI800.4 - TI600.4
4 CHANNEL POWER AMPLIFIER
INPUT
Connect preamp signal cables from the head unit to these terminals.
CROSSOVER FREQUENCY
Controls the crossover point for the speaker outputs.
BASS BOOST
Variable bass boost from 0 to +18dB @ 45 Hz.
2ch/4ch MODE
2ch: Headunit has one pair of cables into front Input.
4ch: Headunit has two pairs of cables into front and rear inputs.
LOW PASS LEVEL CONTROL (LPL)
This port is for connecting the optional remote level control (LPL44). This allows up to 20dB of volume adjustment. This is not a bass boost, it controls the level of the entire low pass signal of the rear channels.
REMOTE MONITORING DISPLAY (RMD)
Connect optional RMD Voltage Display to this port
LEVEL
Used to reach maximum amplifier power with a wide variety of headunits.
CONFIG
FLAT: Crossovers are turned off HP: High pass crossover is on
LP/BP: Low and High Pass crossovers are on, creating a Bandpass (BP) setting for midbass drivers or subwoofers. For a standard subwoofer system, the high pass frequency now becomes a subsonic filter. To turn subsonic filter off, turn the HP FREQ (Subsonic Filter) to 20Hz or Full Counter Clockwise.
12V+
This must be connected to the fused positive terminal (+12V) of the car’s battery. The fuse must be located within 18 inches of the battery.
REMOTE
This must be connected to switched +12V, usually a trigger wire coming from the head unit or ignition.
GND
This must be connected to the negative terminal of the car’s battery or bolted to a clean, unpainted part of the chassis of the vehicle.
SPEAKER OUTPUTS
Used to connect the amplifier to speakers. Use the left + and right - terminals for bridged mode. Minimum impedance is 4 ohm bridged or 2 ohm stereo.
© 2010 Phoenix Gold • www.phoenixgold.com
phoenix gold ti amp manual.indd 4 |
|
|
3/2/10 11:20:41 AM |
|
|