Pelco ES31C, C309M-J, ES30C User Manual

5 (1)

O P E R A T I O N / P R O G R A M M I N G

 

ES30C/ES31C Series

®

Esprit® with IOP

C309M-J (9/04)

2

C309M-J (9/04)

CONTENTS

Section

Page

IMPORTANT SAFETY INSTRUCTIONS ...............................................................................................................................................................................

5

OPERATION .........................................................................................................................................................................................................................

6

POWER-UP DISPLAY ..................................................................................................................................................................................................

6

HOW TO OPERATE YOUR SYSTEM ...........................................................................................................................................................................

6

OPERATING NOTES ...................................................................................................................................................................................................

7

ENVIRONMENTAL RANGE ...............................................................................................................................................................................

7

PAN AND TILT FUNCTIONS ..............................................................................................................................................................................

7

SCAN SPEED ....................................................................................................................................................................................................

7

PRESET FUNCTIONS .........................................................................................................................................................................................

7

RANDOM, FRAME, AND AUTO SCANNING ....................................................................................................................................................

7

ZONES ..............................................................................................................................................................................................................

7

PATTERNS .........................................................................................................................................................................................................

8

PARK .................................................................................................................................................................................................................

8

IR FILTER (MODELS ES30CBW18 AND ES31CBW18 ONLY) ............................................................................................................................

8

AUTO IRIS .........................................................................................................................................................................................................

8

WIPER ...............................................................................................................................................................................................................

8

OPEN COLLECTOR AUXILIARY OUTPUT ...........................................................................................................................................................

8

PROGRAMMING - ES30C16/ES31C16 ...............................................................................................................................................................................

9

PROGRAMMING - ES30C22/ES31C22 ..............................................................................................................................................................................

10

PROGRAMMING - ES30CBW18/ES31CBW18 ..................................................................................................................................................................

11

PROGRAMMING ................................................................................................................................................................................................................

12

ACCESSING MAIN MENU (PRESET 95) ...................................................................................................................................................................

12

AUTO FOCUS MODE .................................................................................................................................................................................................

13

AUTO IRIS .................................................................................................................................................................................................................

14

AUTO IR LEVEL (MODELS ES30CBW18/ES31CBW18 ONLY) ..................................................................................................................................

15

AUTO SHARPNESS ...................................................................................................................................................................................................

16

AZ/EL ........................................................................................................................................................................................................................

17

AZ/EL LINE ................................................................................................................................................................................................................

18

AZIMUTH ZERO ........................................................................................................................................................................................................

19

BACKLIGHT COMPENSATION ..................................................................................................................................................................................

20

DIRECTION ................................................................................................................................................................................................................

21

DIRECTION LINE .......................................................................................................................................................................................................

22

DISPLAY DURATION .................................................................................................................................................................................................

23

GAIN/AGC ................................................................................................................................................................................................................

24

GAIN LIMIT ......................................................................................................................................................................................................

24

IR FILTER MODE (MODELS ES30CBW18/ES31CBW18 ONLY) .................................................................................................................................

25

LIMIT STOPS .............................................................................................................................................................................................................

26

TURNING LIMIT STOPS ON OR OFF ................................................................................................................................................................

26

PROGRAMMING LIMIT STOPS .......................................................................................................................................................................

26

MANUAL LIMIT STOPS ..........................................................................................................................................................................

26

SCAN LIMIT STOPS ................................................................................................................................................................................

28

LINE SYNCHRONIZATION .........................................................................................................................................................................................

29

LOWLIGHT LIMIT (MODELS ES30C22/ES31C22 AND ES30CBW18/ES31CBW18 ONLY) .......................................................................................

30

PARK TIME MINUTES ...............................................................................................................................................................................................

31

PATTERN LENGTH ....................................................................................................................................................................................................

32

POWER-UP MODE ....................................................................................................................................................................................................

33

PROPORTIONAL PAN ................................................................................................................................................................................................

34

RESET CAMERA .......................................................................................................................................................................................................

35

SCAN SPEED ............................................................................................................................................................................................................

36

SHARPNESS .............................................................................................................................................................................................................

37

SHUTTER SPEED .......................................................................................................................................................................................................

38

SPEED PROFILE .........................................................................................................................................................................................................

39

C309M-J (9/04)

3

WHITE BALANCE ......................................................................................................................................................................................................

40

WIPER MODE ...........................................................................................................................................................................................................

41

ZONE BLANK ............................................................................................................................................................................................................

42

ZONES ......................................................................................................................................................................................................................

42

ZOOM .......................................................................................................................................................................................................................

43

ZOOM LIMIT .............................................................................................................................................................................................................

44

ZOOM LINE ...............................................................................................................................................................................................................

45

SPECIFICATIONS ................................................................................................................................................................................................................

46

REGULATORY NOTICES ............................................................................................................................................................................................

49

4

C309M-J (9/04)

IMPORTANT SAFETY INSTRUCTIONS

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

6.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

7.Only use attachments/accessories specified by the manufacturer.

8.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

9.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

10.Installation should be done only by qualified personnel and conform to all local codes.

11.Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture.

12.Use only installation methods and materials capable of supporting four times the maximum specified load.

13.Use stainless steel hardware to fasten the mount to outdoor surfaces.

14.To prevent damage from water leakage when installing a mount outdoors on a roof or wall, apply sealant around the bolt holes between the mount and mounting surface.

15.AN ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm in each pole shall be incorporated in the electrical installation of the building.

16.A readily accessible disconnect device shall be incorporated in the building installation wiring.

CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other that contained in the operating instructions unless you are qualified to do so.

Only use replacement parts recommended by Pelco.

After replacement/repair of this unit’s electrical components, conduct a resistance measurement between the line and exposed parts to verify the exposed parts have not been connected to the line circuitry.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.

This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

WARNING: HAZARDOUS MOVING PARTS. KEEP FINGERS AND OTHER BODY PARTS AWAY.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

C309M-J (9/04)

5

OPERATION

POWER-UP DISPLAY

When the system is powered up, the selected protocol, revision number, and other information is displayed on the monitor. For example, the screen might show the following information:

ESPRIT 16X IOP 1.0h

CONFIGURE DONE

D Address 1

P Address 2

Comm 2400, N, 8, 1

CAMERA XXXX-XXXX

The information displayed depends on the selected protocol (C, D, or P) and the menu selection for powerup mode. (Refer to the Power-Up Mode in the Programming section).

The information remains on the monitor until the system is moved.

HOW TO OPERATE YOUR SYSTEM

 

Operation

How to Control

 

 

 

 

Pan and Tilt

Move joystick left/right and up/down.

 

 

 

 

Scanning

 

 

Stop scan

Call preset 96.

 

Random scan

Call preset 97.

 

Frame scan

Call preset 98.

 

Auto scan

Call preset 99.

 

 

 

 

Zoom Far

To zoom far, do the following:

 

 

1. Press the Zoom Tele button or turn the joystick clockwise until zoom stops at the optical zoom1 limit.

 

 

2. Release the button or joystick.

 

 

3. To continuing zooming (digitally), immediately press the button or turn the joystick clockwise again until you

 

 

have the picture you want or reach the digital zoom2 limit.

 

Zoom Wide

Press the Zoom Wide button or turn the joystick counterclockwise.

 

 

 

 

Presets

Refer to the documentation supplied with the controller.

 

 

 

 

Patterns

Refer to the documentation supplied with the controller.

 

 

 

1

Optical zoom magnifies the image and the picture remains clear. Resolution is constant.

2

Digital zoom magnifies the image and the picture may appear pixilated. The larger the zoom limit the greater the reduction in resolution.

6

C309M-J (9/04)

OPERATING NOTES

ENVIRONMENTAL RANGE

The operating temperature ranges from a minimum of -50°F (-45°C) to a maximum of 122°F (50°C) for sustained system operation or 140°F (60°C) absolute maximum. The entire unit can de-ice and be operational in two hours from a temperature of -13°F (-25°C). The thermostatically controlled heater consumes 10 watts and cycles on at 70°F (21°C) and off at 85°F (29°C), while the window defroster runs continuously and consumes 2.5 watts.

PAN AND TILT FUNCTIONS

Controller

Pan

Tilt

Type

(Capability – 360° Continuous Pan Rotation)**

(Viewing Range – +33° to -83°)***

 

 

 

Fixed speed

Speed determined by controller

Speed determined by controller

 

 

 

*Variable speed

0.1 to 40° per second, depending on joystick and

0.1 to 20° per second, depending on joystick and zoom

 

zoom positions

positions

*Turbo Mode

100° per second

Does not affect the tilt speed

*Preset Mode

100° per second

30° per second

 

 

 

* 50 mph wind-speed profile.

**If manual limit stops are set, “Pan Limit” appears on your monitor when a limit stop is reached (except when you are programming or running a pattern). This does not apply to scan limit stops.

***When the system reaches the upper limit, “Tilt Limit” appears on your monitor (except when you are programming or running a pattern).

If the proportional pan mode is enabled (refer to the Proportional Pan in the Programming section), the pan and tilt speeds will depend on the amount of zoom. At telephoto zoom settings, the pan and tilt speeds will be slower for a given amount of joystick deflection than at wide zoom settings. This keeps the image from moving too fast on the monitor when there is a large amount of zoom. This slowing does not happen when going to a preset but does occur in turbo mode when high zoom is selected. The minimum pan and tilt speeds are 0.1 degree per second at full zoom.

SCAN SPEED

Scan speed is adjustable from 1 to 40 degrees per second through the programming menu.

PRESET FUNCTIONS

The Esprit® system is capable of going to 64 preset locations, each with a 20-character label. The presets are numbered 1-32 and 35-66. Refer to the documentation for your control system for programming presets.

If you command the pan and tilt to go to an undefined preset, erratic operation may result.

Presets 33 and 34 are fixed commands, meaning that you cannot program them. Preset 33 is the “flip” command, which will pan the system 180 degrees. Preset 34 is the “pan zero” command, which will pan the system to the factory-determined zero reference point.

RANDOM, FRAME, AND AUTO SCANNING

Select preset 97 (30) to start random scanning. Select preset 98 (31) to activate frame scanning (three seconds of scanning followed by a three-second pause). Select preset 99 (32) to start auto (continuous) scanning. Scan limit stops are controlled by software. Refer to the Limit Stops section to program the scan limit stops.

When the pan and tilt reaches a scan limit stop, it reverses direction. Select preset 96 (29) to stop a scan. Any pan and tilt or lens command also will stop a scan.

ZONES

A zone is a programmed pan area with set boundaries and identifying label. The Esprit system has a maximum of eight zones, each with a 20-character label. Zones can be programmed to blank video when the camera pans into the zone area. If a zone is blanked, the system displays the message, VIDEO BLANK. (Refer to Zone Blank in the Programming section for instructions.)

C309M-J (9/04)

7

PATTERNS

The Esprit system can do either one full pattern (1.5, 3, or 6 minutes long) or two half patterns (.75, 1.5, or 3 minutes long). This pattern can consist of any standard pan and tilt or lens command. Presets, flip, digital zoom, proportional pan, and turbo are not allowed in a pattern. Zones can be enabled while running a pattern. Refer to the documentation for your control system to program and run patterns.

PARK

If the system does not receive any commands for a specified period of time (refer to the Park Time Minutes section), the system goes to preset 1 and parks. If the time specified is zero, or if preset 1 has not been programmed, the pan and tilt will not park.

IR FILTER (MODELS ES30CBW18 AND ES31CBW18 ONLY)

The ES30CBW18 and ES31CBW18 models have an IR (infrared) lens filter that can switch in and out, automatically or manually, depending on how the system is programmed. When the filter is IN, the camera produces a color picture. When the IR filter switches OUT, the picture changes to black and white, increasing visibility in low light conditions.

The Auto IR Level setting controls automatic operation of the filter. To manually override automatic operation, use presets 88 (filter IN) and 89 (filter OUT). The unit will remain in manual control until it is panned or tilted more than 15 degrees.

LOW LIGHT does not mean NO LIGHT. Some type of illumination is required (street light, IR light, etc.).

AUTO IRIS

If auto iris is in the auto mode, it remains that way until you manually open or close the iris. The system will return to auto iris when it is panned or tilted more than 15 degrees.

WIPER

The ES31C Series features a window wiper to clear moisture from the enclosure glass. There are two modes of operation for the wiper, momentary and continuous. The wiper mode is easily set up through on-screen programming (refer to the Wiper Mode section).

To operate the wiper do the following:

Momentary Mode – To operate the wiper one full cycle, press the AUX 1 button on your controller. Each press of the button operates the wiper one full cycle, even if the AUX 1 button is latching. If AUX 1 is latching, the first press will activate the wiper (open the latch). Pressing AUX 1 a second time closes the latch, but will not cycle the wiper. Press the AUX 1 key again to cycle the wiper.

Continuous Mode – To operate the wiper press the AUX 1 button on your controller. The wiper will continue to operate until the AUX 1 button is pressed again or until the programmed cycle is completed.

NOTE: CM9740 and CM9760 Matrix Systems Only – For the wiper to operate in continuous mode, the AUX 1 function in the camera file must be set to latching. If the AUX 1 camera file is not latching, the wiper will only operate in momentary mode, even if the Esprit wiper is programmed for continuous operation. Refer to the operation manual supplied with the CM9740 or CM9760 matrix system for instructions.

OPEN COLLECTOR AUXILIARY OUTPUT

An AUX 2 command from the controller will activate a device, such as a relay. The output will remain active for two seconds and then deactivate, even if the controller is set to latching mode.

Examples of devices that can be used with AUX 2 are a washer assembly (not supplied by Pelco) or a latching relay (not supplied by Pelco) attached to control a gate, lights, etc.

If a relay is used it must require less than 32 VDC and 40 mA to trigger the relay coil. The relay must be placed within 100 feet (30 m) of the Esprit unit.

8

C309M-J (9/04)

PROGRAMMING - ES30C16/ES31C16

1.Access main menu (preset 95).

2.Make main menu selections.

Joystick: Move up or down to position cursor or to toggle between selections.

Iris Open: Enter.

Camera Menu

 

Iris Close: Cancel.

 

Backlight comp

Off

 

 

Zoom limit

x- -

 

Reset camera

 

 

<Gain/AGC>

 

MAIN MENU

<Auto iris>

 

<Camera>

Next

 

Exit

 

<Line Sync>

 

 

<Power Up>

 

 

*<Wiper>

 

 

<Limit Stop>

Line Sync Menu

 

<Other>

 

Line Sync

On

Exit

 

Line Sync Phase

0

 

Exit

 

PRESETS

The following presets are reserved for special functions.

 

 

Power-Up Menu

Preset

Function

Power Up Default

Exit

1

Park

 

33Flip command

34Pan zero command 90-91 Manual limit stops 92-93 Auto limit stops

95Select camera programming menu

96

Stop a scan

 

*Wiper Menu

97

Random scanning

 

 

Wiper Mode

Momentary

98

Frame scanning

 

99

Auto scanning

 

Wiper Dwell <s>

2

 

Wiper Time <m>

60

 

 

 

*ES31C only

 

Exit

 

 

 

 

NOTE: For American Dynamics

 

 

 

controllers with only 32 presets,

 

 

 

set Esprit DIP switch SW1-5 to

 

 

 

the ON position. When SW1-5

 

Limit Stop Menu

is ON, preset

 

Limit Stops

Off

 

 

 

 

99 becomes 32

 

Set Man Limits

 

 

 

Clear Man Limits

 

 

98 becomes 31

 

Set Scan Limits

 

 

97 becomes 30

 

Clear Scan Limits

 

 

 

 

 

96 becomes 29

 

Exit

 

 

95 becomes 28

 

 

 

 

94 becomes 27

 

 

 

 

93 becomes 26

 

 

 

 

92 becomes 25

 

Other Menu

 

91 becomes 24

 

 

 

Proportional pan

On

 

90 becomes 23

 

 

89 becomes 22

 

Park time minutes

0

 

88 becomes 21

 

Scan Speed deg/s

25

 

 

Pattern Length

1.5 min

 

 

 

If the limit stops are turned off

 

Spd Profile

 

 

<Zone Blank>

 

(refer to the Limit Stops section),

 

 

 

<Az/El/Direction>

 

presets 23-26 can be used as

 

Exit

 

regular presets.

 

 

 

Gain/AGC Menu

 

Gain Limit

27

Exit

 

Auto Iris Menu

 

Auto-iris mode

Auto

Auto-iris level

66

Auto-iris peak

 

Exit

 

Next Menu

 

Shutter speed

Auto

Auto focus mode

Auto

<Sharpness>

 

<White balance>

 

Prev

 

Exit

 

Zone Blank Menu

 

Video Blank Zone

1 Off

 

2 Off

 

3 Off

 

4 Off

 

5 Off

 

6 Off

 

7 Off

Exit

8 Off

 

Az/El/Direction

 

Set Azimuth Zero

 

Az/El

 

Az/El Line

 

Direction

 

Direction Line

 

Zoom

 

Zoom Line

 

Disp Duration

 

Exit

 

Sharpness Menu

 

Auto Sharpness

On

Sharpness

5

Exit

 

White Balance Menu

Auto white bal

Auto

R-Gain

 

B-Gain

 

Exit

 

For detailed instructions, refer to the following sections.

Menu items are listed alphabetically.

C309M-J (9/04)

9

PROGRAMMING - ES30C22/ES31C22

1.Access main menu (preset 95).

2.Make main menu selections.

Joystick: Move up or down to position cursor or to toggle between selections.

Iris Open: Enter.

Camera Menu

 

Iris Close: Cancel.

 

Backlight comp

Off

 

 

Zoom limit

x- -

 

Reset camera

 

 

<Gain/AGC>

 

MAIN MENU

<Auto iris>

 

<Camera>

Next

 

Exit

 

<Line Sync>

 

 

<Power Up>

 

 

*<Wiper>

 

 

<Limit Stop>

Line Sync Menu

 

<Other>

 

Line Sync

On

Exit

 

Line Sync Phase

0

 

Exit

 

PRESETS

The following presets are reserved for special functions.

 

 

Power-Up Menu

Preset

Function

Power Up Default

Exit

1

Park

 

33Flip command

34Pan zero command 90-91 Manual limit stops 92-93 Auto limit stops

95Select camera programming menu

96

Stop a scan

 

*Wiper Menu

97

Random scanning

 

 

Wiper Mode

Momentary

98

Frame scanning

 

99

Auto scanning

 

Wiper Dwell <s>

2

 

Wiper Time <m>

60

 

 

 

*ES31C only

 

Exit

 

 

 

 

NOTE: For American Dynamics

 

 

 

controllers with only 32 presets,

 

 

 

set Esprit DIP switch SW1-5 to

 

 

 

the ON position. When SW1-5

 

Limit Stop Menu

is ON, preset

 

Limit Stops

Off

 

 

 

 

99 becomes 32

 

Set Man Limits

 

 

 

Clear Man Limits

 

 

98 becomes 31

 

Set Scan Limits

 

 

97 becomes 30

 

Clear Scan Limits

 

 

 

 

 

96 becomes 29

 

Exit

 

 

95 becomes 28

 

 

 

 

94 becomes 27

 

 

 

 

93 becomes 26

 

 

 

 

92 becomes 25

 

Other Menu

 

91 becomes 24

 

 

 

Proportional pan

On

 

90 becomes 23

 

 

89 becomes 22

 

Park time minutes

0

 

88 becomes 21

 

Scan Speed deg/s

25

 

 

Pattern Length

1.5 min

 

 

 

If the limit stops are turned off

 

Spd Profile

 

 

<Zone Blank>

 

(refer to the Limit Stops section),

 

 

 

<Az/El/Direction>

 

presets 23-26 can be used as

 

Exit

 

regular presets.

 

 

 

Gain/AGC Menu

 

Gain Limit

28

Exit

 

Auto Iris Menu

 

Auto-iris mode

Auto

Auto-iris level

 

Auto-iris peak

 

Exit

 

Next Menu

 

LowLight limit

 

Shutter speed

Auto

Auto focus mode

Auto

<Sharpness>

 

<White balance>

 

Prev

 

Exit

 

Zone Blank Menu

 

Video Blank Zone

1 Off

 

2 Off

 

3 Off

 

4 Off

 

5 Off

 

6 Off

 

7 Off

 

8 Off

Exit

 

Az/El/Direction

 

Set Azimuth Zero

 

Az/El

 

Az/El Line

 

Direction

 

Direction Line

 

Zoom

 

Zoom Line

 

Disp Duration

 

Exit

 

Sharpness Menu

 

Auto Sharpness

On

Sharpness

13

Exit

 

White Balance Menu

 

Auto white bal

On

R Gain

 

B-Gain

 

Exit

 

For detailed instructions, refer to the following sections.

Menu items are listed alphabetically.

10

C309M-J (9/04)

Pelco ES31C, C309M-J, ES30C User Manual

PROGRAMMING - ES30CBW18/ES31CBW18

1.Access main menu (preset 95).

2.Make main menu selections.

Joystick: Move up or down to position cursor or to toggle between selections.

Iris Open: Enter.

Camera Menu

 

Iris Close: Cancel.

 

Backlight comp

Off

 

 

Zoom limit

x72

 

Reset camera

 

 

<Gain/AGC>

 

MAIN MENU

<Auto iris>

 

<Camera>

Next

 

Exit

 

<Line Sync>

 

 

<Power Up>

 

 

*<Wiper>

 

 

<Limit Stop>

Line Sync Menu

 

<Other>

 

Line Sync

On

Exit

 

Line Sync Phase

0

 

Exit

 

PRESETS

The following presets are reserved for special functions.

 

 

Power-Up Menu

Preset

Function

Power Up Default

Exit

1

Park

 

33Flip command

34Pan zero command

88IR filter IN

89IR filter OUT

90-91

Manual limit stops

 

 

 

92-93

Auto limit stops

 

 

 

95

Select camera

 

*Wiper Menu

 

programming menu

 

 

 

Wiper Mode

Momentary

96

Stop a scan

 

97

Random scanning

 

Wiper Dwell <s>

2

 

Wiper Time <m>

60

98

Frame scanning

 

 

Exit

 

99

Auto scanning

 

 

 

 

 

*ES31C only

 

 

 

NOTE: For American Dynamics

 

 

 

controllers with only 32 presets,

 

 

 

set Esprit DIP switch SW1-5 to

 

Limit Stop Menu

the ON position. When SW1-5

 

Limit Stops

Off

is ON, preset

 

 

Set Man Limits

 

 

 

 

 

 

99 becomes 32

 

Clear Man Limits

 

 

 

Set Scan Limits

 

 

98 becomes 31

 

Clear Scan Limits

 

 

 

 

 

97 becomes 30

 

Exit

 

 

96 becomes 29

 

 

 

 

95 becomes 28

 

 

 

 

94 becomes 27

 

 

 

 

93 becomes 26

 

Other Menu

 

92 becomes 25

 

 

 

Proportional pan

On

 

91 becomes 24

 

 

90 becomes 23

 

Park time minutes

0

 

89 becomes 22

 

Scan Speed deg/s

25

 

 

Pattern Length

1.5 min

 

88 becomes 21

 

 

 

Spd Profile

 

 

 

 

 

If the limit stops are turned off

 

<Zone Blank>

 

 

<Az/El/Direction>

 

(refer to the Limit Stops section),

 

Exit

 

presets 23-26 can be used as regular presets.

Gain/AGC Menu

 

Gain Limit

28

Exit

 

Auto Iris Menu

 

Auto-iris mode

Auto

Auto-iris level

 

Auto-iris peak

 

Exit

 

Next Menu

 

LowLight limit

2

Shutter speed

Auto

Auto focus mode

Auto

<IR Filter>

 

<Sharpness>

 

<White balance>

 

Prev

 

Exit

 

Zone Blank Menu

 

Video Blank Zone

1 Off

 

2 Off

 

3 Off

 

4 Off

 

5 Off

 

6 Off

 

7 Off

 

8 Off

Exit

 

Az/El/Direction

 

Set Azimuth Zero

 

Az/El

 

Az/El Line

 

Direction

 

Direction Line

 

Zoom

 

Zoom Line

 

Disp Duration

 

Exit

 

IR Filter Menu

 

IR filter mode

Auto

Auto IR Level

Dusk

Exit

 

Sharpness Menu

 

Auto Sharpness

On

Sharpness

 

Exit

 

White Balance Menu

 

Auto white bal

On

R-Gain

 

B-Gain

 

Exit

 

For detailed instructions, refer to the following sections.

Menu items are listed alphabetically.

C309M-J (9/04)

11

PROGRAMMING

ACCESSING MAIN MENU (PRESET 95)

You can call up the main menu on your monitor by programming (setting or creating) preset 95 (28 if in 32-preset mode).

Programming preset 95 for Pelco’s controllers varies according to the type of controller you are using. Instructions for programming preset 95 are given below for various Pelco controllers.

CM6700

1.Enter the number of the camera and press the CAM key.

2.Enter 95 and hold the PRESET key for two seconds.

3.In the Edit Preset menu, arrow to SET and press the ACK key. The main menu appears.

KBD200A/KBD300A (Direct Mode Only)

1.Enter 95.

2.Hold the PRESET key (approximately 5 seconds) until the main menu appears on the screen.

CM8500

1.Enter the number of the camera and press the CAM key.

2.Highlight PRESET in the Camera menu and hold down the joystick button until the Set Presets prompt appears.

3.Enter 95 and press the PRESET key. The text editor appears. Select ENTER and the main menu appears.

CM9500

1.Enter the number of the camera and press the CAM key. The Main menu appears.

2.Highlight SETUP in the Main menu and press the SELECT key.

3.Highlight CAM in the Setup menu and press the SELECT key.

4.Highlight PRESET in the Camera menu and press the SELECT key.

5.Enter 95 and press the F1 key. The main menu appears.

CM9750

1.Turn the KEY SWITCH to the ON position.

2.Press the PROG key. PROGRAM appears on the LCD display.

3.Press the PRES key. The PRESET prompt appears.

4.Enter 95 and press the ENTER key. The main menu appears.

5.Turn the KEY SWITCH to the OFF position.

CM9740/CM9760/CM9770

1.Press the ESCAPE key to open the Main menu. Select DEF. The Define Menu appears.

2.Enter your four-digit PIN if this is your first time entering this mode.

3.Enter 95 and select PRST. The main menu appears on the monitor.

4.Select the Quit icon to return to the default menu.

KBD4000/KBD4002/KBD4000V

1.Press the SPOT MONITOR key.

2.Enter 95, and then hold the PRESET key (approximately five seconds) until the main menu appears on the screen.

MPT9500

Standard Coaxitron® Mode

1.Enter 95 and press the PRESET SET key.

2.Position the asterisk in the YES row and press the F1 key. The main menu appears.

Extended Coaxitron or RS-485 Mode

1.Enter 95 and press the PRESET SET key.

2.Press the F2 key. The main menu appears.

12

C309M-J (9/04)

AUTO FOCUS MODE

MAIN MENU

 

Camera Menu

 

 

Next Menu

 

 

 

Backlight comp

Off

 

LowLight limit

 

<Camera>

 

<Line Sync>

 

Zoom limit

x- -

 

Shutter speed

Auto

<Power Up>

 

Reset camera

 

 

Auto focus mode

Auto

<Wiper>

 

<Gain/AGC>

 

 

<Sharpness>

 

<Limit Stop>

 

<Auto iris>

 

 

<White balance>

 

<Other>

 

Next

 

 

Prev

 

Exit

 

Exit

 

 

Exit

 

There are two auto focus modes:

Auto – If auto focus is in the auto mode, pressing the Focus Far or Focus Near button will place the focus in the manual mode. The system will return to auto focus if you pan or tilt the unit or do a zoom function.

Off – If the mode is set to off, the system will operate in the manual mode with one exception. If you issue a command to go to a preset, auto focus will turn on and remain on until you press the Focus Far or Focus Near button.

NOTE: Auto focus does not operate at shutter speeds longer than 1/8 of a second.

To change the mode:

1.Program preset 95 (28). The main menu appears.

2.Position the cursor (>) beside Camera.

3.Press the Iris Open button to enter the Camera menu.

4.Position the cursor (>) beside Next.

5.Press the Iris Open button to go to the next camera menu.

6.Position the cursor (>) beside Auto Focus Mode.

7.Press the Iris Open button. The cursor moves to the right, beside the word Auto or Off.

8.Move the joystick up or down to toggle between Auto and Off.

9.SELECT – Press the Iris Open button on your keyboard to select your choice. CANCEL – Press the Iris Close button if you do not want to change the setting.

C309M-J (9/04)

13

AUTO IRIS

MAIN MENU

 

Camera Menu

 

 

 

Backlight comp

Off

<Camera>

<Line Sync>

 

Zoom limit

x- -

<Power Up>

 

Reset camera

 

<Wiper>

 

<Gain/AGC>

 

<Limit Stop>

 

 

 

 

<Auto iris>

 

<Other>

 

Next

 

Exit

 

Exit

 

Auto Iris Menu

 

Auto-iris mode

Auto

Auto-iris level

 

Auto-iris peak

 

Exit

 

The following are the settings for auto iris:

Mode

Level

Peak

To change the settings for auto iris:

1.Program preset 95 (28). The main menu appears.

2.Position the cursor (>) beside Camera.

3.Press the Iris Open button to enter the Camera menu.

4.Position the cursor (>) beside Auto Iris.

5.Press the Iris Open button. The Auto Iris menu appears.

6.Position the cursor (>) and select one of the following settings: MODE – The cursor moves to one of two choices:

Auto – The iris is automatically adjusted to produce a constant video output as determined by the Level setting. Off – Auto iris is disabled, and control is always manual.

Move the joystick up or down to toggle between Auto and Off. Press the Iris Open button to select the choice, or press the Iris Close button if you do not want to change the setting.

LEVEL – The cursor moves to a numeric value, which the system uses to try to maintain a certain light level. Changing the value of the Level setting will change the video level to which the auto iris adjusts. This setting should be adjusted if the video level in the auto iris mode is too bright or too dark. Move the joystick up or down to a value. Press the Iris Open button to select the value, or press the Iris Close button if you do not want to change the setting.

PEAK – The cursor moves to a numeric value. Increasing this value will cause the auto iris circuit to react more to highlights or “peaks” in the picture. Decreasing this value will cause it to use the average video level to adjust the iris. Move the joystick up or down to a value. Press the Iris Open button to select the value, or press the Iris Close button if you do not want to change the setting.

14

C309M-J (9/04)

AUTO IR LEVEL (MODELS ES30CBW18/ES31CBW18 ONLY)

MAIN MENU

 

Camera Menu

 

 

Next Menu

 

 

IR Filter Menu

 

 

 

Backlight comp

Off

 

LowLight limit

Auto

 

IR filter mode

Auto

<Camera>

<Line Sync>

 

Zoom limit

x- -

 

Shutter speed

Auto

 

 

 

 

 

 

Auto IR Level

Dusk

<Power Up>

 

Reset camera

 

 

Auto focus mode

Auto

 

Exit

 

<Wiper>

 

<Gain/AGC>

 

 

<IR Filter>

 

 

 

 

<Limit Stop>

 

<Auto iris>

 

 

<Sharpness>

 

 

 

 

<Other>

 

Next

 

 

<White balance>

 

 

 

 

Exit

 

Exit

 

 

Prev

 

 

 

 

 

 

 

 

 

Exit

 

 

 

 

The auto IR level is the light level at which the infrared filter switches IN or OUT. Following are the available settings for the Auto IR Level:

DUSK (default) – approximately 6 lux (black-white) approximately 13 lux (color)

DARK – approximately 0.1 lux (black-white) approximately 2 lux (color)

NOTE: If backlight compensation is ON and the IR cut filter switches OUT in normal lighting conditions, adjust the Auto IR Level to a darker setting. Refer to the Backlight Compensation section.

NOTE: LOW LIGHT does not mean NO LIGHT. Some type of illumination is required (street light, IR light, etc.). The camera is not sensitive to IR light when the IR cut filter is IN.

To change the auto lR level settings:

1.Program preset 95 (28). The main menu appears.

2.Position the cursor (>) beside Camera.

3.Press the Iris Open button to enter the Camera menu.

4.Position the cursor (>) beside Next.

5.Press the Iris Open button to enter the Next menu.

6.Position the cursor (>) beside IR Filter.

7.Press the Iris Open button to enter the IR Filter menu.

8.Position the cursor (>) beside Auto IR Level.

9.Press the Iris Open button. The cursor moves to the right.

10.Move the joystick up or down to toggle between the level settings.

11.SELECT – Press the Iris Open button on your keyboard to select your choice. CANCEL – Press the Iris Close button if you do not want to change the setting.

C309M-J (9/04)

15

Loading...
+ 35 hidden pages