Paxar Stacker Monarch 932TM User Manual

Size:
2.26 Mb
Download

Operatingrating

Instructionsuctions

Monarch®

932™ Stacker

78901

23456 Tackle Fishing .00 $40

78901

23456 Tackle Fishing .00 $40

78901

23456 Tackle Fishing .00 $40

78901

23456 Tackle Fishing .00 $40

 

 

 

TC0932OI Rev. AC 12/07

©2004 Paxar Americas, Inc. a subsidiary of Avery Dennison Corp. All rights reserved.

Each product and program carries a respective written warranty, the only warranty on which the customer can rely. Paxar Americas reserves the right to make changes in the product, the programs, and their availability at any time and without notice. Although Paxar Americas has made every effort to provide complete and accurate information in this manual, Paxar Americas shall not be liable for any omissions or inaccuracies. Any update will be incorporated in a later edition of this manual.

©2004 Paxar Americas, Inc. a subsidiary of Avery Dennison Corp. All rights reserved. No part of this publication may be reproduced, transmitted, stored in a retrieval system, or translated into any language in any form by any means, without the prior written permission of Paxar Corporation.

WARNING

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

CANADIAN D.O.C. WARNING

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe A prescrites dans le Réglement sur le brouillage radioélectriqueédicte par le minist re des Communications du Canada.

Trademarks

Monarch®, 932, 9855, and 9860, are trademarks of Paxar Americas, Inc.

Paxar® is a trademark of Paxar Corporation.

Avery Dennison® is a trademark of Avery Dennison Corporation.

Avery Dennison Printer Systems Division

170 Monarch Lane

Miamisburg, OH 45342

TA B L E O F C O N T E N T S

GETTING STARTED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Unpacking the Stacker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Installing the Stacker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Step 1 - Installation for the 9860 Printer . . . . . . . . . . . . . . . . . . . . . . . 1-2

Step 2 - Level the Stacker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Step 3 - Connect the Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Step 4 - Check the Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Step 5 - Set the Tag Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Step 6 - Set the Belt Speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

HOW TO OPERATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Re-Loadingor Changing Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2Emptying the Stacker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2Stacker Full . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2Stacker Running . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

Clearing a Tag Jam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Installing Riser Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Stacker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Minimum Stacked Tag Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

i Table of Contents

ii Table of Contents

G E T T I N G S TA R T E D

1

The Monarch® 932ä stacker works with a Monarch® 9860ä printer. The stacker supports backfeed mode on the printer. There is no power ON/OFF switch for the stacker. Once the stacker is plugged into an outlet, it is on.

U n p a c k i n g t h e S t a c k e r

uImportant: After unpacking the stacker, look through all packaging material for parts. Keep all packaging material for future shipping.

I n s t a l l i n g t h e S t a c k e r

Use these instructions when you first install the stacker or when you need to move the stacker to a different location.

Before installing:

uFind a level work surface at least 52" x 22" (1321 mm x 559 mm).

The 9860 printer comes with a knife attached.

u Turn off the printer before you install the stacker.

Getting Started 1-1

S t e p 1 - I n s t a l l a t i o n f o r t h e 9 8 6 0 P r i n t e r

1. Locate the screw hole on the stacker mounting plate.

Flanged screw

 

Adjusting

Stacker

Mounting

Bracket

Plate

2.Attach the adjusting bracket to the stacker mounting plate using a flanged screw as shown (do not tighten all the way).

Guide Tab

Knife Opening

Mounting

Plate

Slot

Locating Pin

Adjusting Bracket

Locating Hole

3.Gently lift stacker and center the guide tabs in the knife opening.

4.Set the stacker locating pins (on bottom of stacker) firmly in the adjusting bracket locating hole and mounting plate slot.

5.Tighten the adjusting bracket flanged screw.

6.Connect the stacker cable to the knife.

1-2 Getting Started

S t e p 2 - L e v e l t h e S t a c k e r

1.Check the distance between the rollers and the knife. Make sure the rollers are not touching the front of the knife or too far from the knife. If incorrect, follow the steps below. If correct, skip this step and move on to Step 3 - Connect the Power Cord.

Rollers

Knife

The ideal position for the stacker is with the end of tray slightly down.

2.Loosen the locking nuts with a wrench.

3.Make sure the stacker’s feet are flat on a level surface.

You can raise or lower the feet by turning them.

4. Evenly adjust both feet.

If the stacker is

Locking

Nuts

utouching the knife case, lower the feet.

utoo far from the knife, raise the feet.

5.Tighten the locking nuts.

Getting Started 1-3

S t e p 3 - C o n n e c t t h e P o w e r C o r d

1. Plug the power cord into the stacker’s AC inlet.

AC Inlet

2.Plug the other end of the power cord into a grounded outlet. Once the power cord is attached to an outlet, the stacker is on. There is no power ON/OFF switch for the stacker.

1-4 Getting Started

S t e p 4 - C h e c k t h e A l i g n m e n t

1.Load supply in the printer. For more information about loading supply, refer to the printer’s Operator’s Handbook or Quick Reference.

2.Set aside the tag weight.

3.Widen the guide rails to maximum width by pulling and extending the guide rails out of the grooves at the bottom of the tray.

GuideRails

Grooves

4.Slide the rod ends of guide rails by using both hands to the outer position.

Getting Started 1-5

5.Move tag stop up and down by using your thumb to pull out slightly on the release tab and lift up until it stops.

Adjust the tag stop to the length of the tags.

Tag Stop

Transport Lock

6.Make sure the transport lock handle is in the locked position.

7.Make sure supply is loaded and the printer is turned on.

8.Press the Feed orCut button on the printer or keyboard several times.

The supply should feed through the knife and tags should be cut and placed in the stacker tray.

1-6 Getting Started