Paxar Rewind Monarch 415 User Manual

Size:
773.13 Kb
Download

Monarch 415 TM

Rewind

Operator’s Handbook

TC0415OH Rev. D 5/96 ©1990-96Monarch Marking Systems, Inc. All rights reserved.

Each product and program carries a respective written warranty, the only warranty on which the customer can rely. Monarch reserves the right to make changes in the product and the programs and their availability at any time and without notice. Although Monarch has made every effort to provide complete and accurate information in this manual, Monarch shall not be liable for any omissions or inaccuracies. Any update will be incorporated in a later edition of this manual.

Trademarks

MONARCH is a registered trademark of Monarch Marking Systems, Inc. 415 is a trademark of Monarch Marking Systems, Inc.

Paxar is a trademark of Paxar Corporation.

Monarch Marking Systems

P.O. Box 608

Dayton, Ohio 45401

Table of Contents

1.

Setting Up ..........................................................................

1

2.

Connecting Supplies ........................................................

3

 

Rewinding on the Hub..................................................

3

 

Rewinding on a Paper Core .........................................

5

3.

Operating the Rewind .......................................................

7

 

Starting.........................................................................

7

 

Stopping .......................................................................

8

4.

Changing Hubs .................................................................

9

5.

Burster Option Setup and Operation ............................

11

 

Supply Removal .........................................................

19

6.

Specifications and Supplies ..........................................

21

7.

Troubleshooting...............................................................

22

Appendix A: Rewind Alignment.........................................

23

i

Monarch 415 Rewind Operator’s Handbook

ii

1. Setting Up

1.Push the 415 Rewind power switch OFF.

2.Place the rewind on a level surface. Be sure it is at least ten inches away from the supply exit of the printer (Figure 1).

3.Squarely align the rewind’s hub flange with the edge of the supply. See Appendix A, "Rewind Alignment."

Hub

Flange

 

Printer

 

Supply

Hub

Exit

 

Power

Switch

Figure 1

1

Monarch 415 Rewind Operator’s Handbook

4.Plug the power cord into the rewind (Figure 2). Then, plug the power cord into a grounded electrical outlet.

Fuse Holder

Power

Switch

Power

Cord

Figure 2

2

2. Connecting Supplies

Rewinding on the Hub

1.Slide the supply guide away from the hub flange and pull it away from the hub.

2.Print or feed enough supplies from the printer to wrap around the hub one and one half times.

3.Hold the hub flange and twist the hub clockwise until it stops.

4.Thread the supply strip under the dancer roller.

5.Fold and insert the end of the supply strip into the slot (Figure 3). Be sure the supply is against the hub flange.

Supply

Hub Strip

Flange

Slot

Dancer

Supply

Guide

 

Roller

 

 

Figure 3

 

3

Monarch 415 Rewind Operator’s Handbook

6.Turn the hub and hub flange at least one full turn counterclockwise to tighten the supply strip.

7.Push the supply guide against the hub then slide it against the supply.

NOTE: Units with 3" hubs have a flanged disk instead of a supply guide.

Slide this disk over the hub and against the stock/core (Figure 4).

Figure 4

4

2. Connecting Supplies

Rewinding on a Paper Core

1.Slide the supply guide away from the hub flange and pull it away from the hub.

2.Push the paper core on the hub until it is against the hub flange.

3.Hold the hub flange and twist the hub clockwise until the paper core is tight.

4.Tape the supply strip to the paper core (Figure 5). Be sure the supply is against the hub flange.

Hub

Flange

Tape

Supply

Strip

Paper

Core Hub

Figure 5

5

Monarch 415 Rewind Operator’s Handbook

5.Turn the hub and hub flange at least one full turn counterclockwise to tighten the supply strip.

6.Push the supply guide against the hub then slide it against the supply.

6