Paxar Monarch 9433 User Manual

Size:
2.92 Mb
Download

M O N A R C H 9 4 3 3 ™

V E H I C L E M O U N T I N S T R U C T I O N S

Using the Vehicle Mount, you can attach your Monarch 9433 printer to a forklift or other vehicle.

This document describes how to install and use the vehicle mount with the printer.

Note: The information in this document supersedes information in previous versions. Check our Web site (www.monarch.com) for any updates.

I n s t a l l i n g t h e B a t t e r y P a c k

1. Pull the release levers on both sides of the printer to open the supply door.

2. Insert the connector end of the battery pack into the printer and close the supply door until the levers click into place.

 

 

 

TC9433VMOI Rev AB 8/08

©2006 Paxar Americas, Inc. a subsidiary of Avery Dennison Corporation.

 

All Rights Reserved.

C o n n e c t i n g t h e C o m m u n i c a t i o n s C a b l e s

The printer uses either 9-pinserial communications or USB communications. For best results, use only Monarch® cables.

Open the hinged cable door by loosening the two Phillips screws and lifting up on the door.

Serial Cable

1. Plug the DB9 connector into the DB9 port.

2. Place the cable in the cable cavity.

3. Close the hinged cable door and tighten the screws.

DB9 Connector

USB Cable

1. Plug the USB cable into the USB port.

2. Lock the cable in place by placing it behind the left screw post and into the cable cavity as shown.

3. Closed the hinged cable door and tighten the screws.

USB

Port

USB

Cable

I n s t a l l i n g t h e M o u n t

Following is a list of the mounting hardware. This hardware is not provided for vertical mounting.

four screws (¼-20x 2¼ socket head cap)

four ¼-inchflat washers

four dampening washers

one clamping plate

four M5x0.8 screws (not included)

2

Installing on a Tabletop

1. Select a suitable location for the mount on your vehicle.

2. Align the four outside holes on the vehicle mount with the corresponding holes in your vehicle.

3. Place the four dampening washers between the vehicle and the bottom of the vehicle mount. The washers should be aligned with the nuts on the vehicle mount and the holes on your vehicle.

4. Attach the vehicle mount to your vehicle using four M5x0.8 screws.

Nut

Dampening

Washer

.

3

Installing Overhead (Upside Down)

1. Select a suitable location for the mount on your vehicle.

2. Center the clamping plate on two of your vehicle’s overhead rails.

3. Align the four inside nuts in the vehicle mount with the holes in the clamping plate.

4 . Use the four¼-20x2¼screws and flat washers to attach the vehicle mount to your vehicle.

¼-20x2¼”Screw

Flat Washer

Clamping Plate

4

Installing Vertically

No screws or mounting hardware are provided for vertical installation. 1. Select a suitable location for the mount on your vehicle.

2. Align the nuts in the vehicle mount with the corresponding holes in your vehicle.

3. Use appropriate screws to attach the vehicle mount to your vehicle, or to the appropriate hardware for vertical mounting.

.

5

A t t a c h i n g t h e P r i n t e r

To attach the printer on the vehicle mount:

1. Make sure the printer’s battery and communication cable are installed.

2. Insert the printer into the brackets of the vehicle mount using the knobs as a guide.

3. Push down firmly on the brackets so the printer locks completely in place.

Brackets

Knob

6

S e c u r i n g t h e C a b l e s

Use the cable guides located on the inside and front of the vehicle mount to secure any cables.

1. Attach the printer to the vehicle mount.

2. Thread the cable through the first opening and out the second opening of the cable guide on the inside of the mount, then through the cable guide in the front of the mount.

Cable Guides

3. Connect the cable to the printer.

.

7

L o a d i n g S u p p l i e s

To load supplies into the printer:

1. Turn off the printer.

2. Attach the printer to the vehicle mount.

3. Squeeze the supply bracket and thespring-loadedsupply holder. Pull the hook end of the supply holder and turn it to the left to release the supply bracket. Pull the bracket up.

Supply Bracket

Spring

Supply Holder

Note: The supply holder cannot be removed.

4. Load the supply so it unrolls from the bottom.

5. Lower the bracket so the supply turns freely, then squeeze the supply bracket and pull and turn the supply holder to the right to lock the supply roll in place.

8

6. Pull the release levers located on both sides of the printer to open the supply door.

Release Lever

7. Insert an empty3-inchcore in between the supply holder tabs to open them to their widest position.

8. Slide the supply guides, located inside the printer on each side of the external supply slot, out to their widest position.

9. Feed the supply under the opening in the mounting plate and into the supply slot on the bottom of the printer.

.

9

10. Center-adjustthe supply guides so that they barely touch the edge of the supply.

11. Pull out enough supply to lay across the exit chute.

12. Close the supply door until the release levers click into place.13. Turn on the printer.

14. Press F to advance the supply.

Refer to your Operator’s Handbook for information on printing with your Monarch® 9433™ printer.

10