Paxar Intelligent Keyboard Monarch 939i User Manual

Size:
1.27 Mb
Download

Three-parttag (number of parts = 3)

Cut here for a cut multiple of 1

(Cut after one tag) OR Print multiple = 1 (Prints one tag

as a set)

Cut here for a cut multiple of 2

(Cut after two tags) OR Print multiple = 2 (Prints two

tags as a set)

Entering Batch Data 3-9

3-10 Entering Batch Data

T R O U B L E S H O O T I N G

4

This chapter provides solutions to keyboard problems and explains common status code messages you may receive when using the keyboard.

Problem

Action

The keyboard display is blank.

Make sure the printer is ON. Make sure the

 

keyboard cable is securely attached to the

 

printer. If the keyboard was attached while the

 

printer was on, turn OFF the printer and then

 

back ON.

The data you entered is not

Refer to your format for acceptable characters

accepted.

for this field. Some fields accept only letters,

 

some accept only numbers, and some accept

 

only specific ranges of letters or numbers.

Your data was not accepted

This field requires data for all underscores

and blanks are still showing.

shown. Enter the correct data and press N.

You entered an incorrect check

The data and check digit must be the correct

digit.

combination. Enter the correct data and press

 

the N.

You tried to skip a required

This field requires data before continuing to the

field.

next field. Enter data and press the N.

Letters are not in the expected

Make sure the Caps Lock (c) is not on.

case.

 

Monetary symbols do not print

Make sure your font supports the selected code

as expected.

page (Bold, ANSI, etc.). For more information,

 

see Appendix B, "Character Sets."

Script is not running.

Turn printer off and then back on. If this does

 

not solve the problem, contact Technical Support

 

for more information.

Scanner does not work.

Make sure the scanner is connected and

 

configured. See Appendix C, "Configuring the

 

System," for more information.

Troubleshooting 4-1

4-2 Troubleshooting

S P E C I F I C AT I O N S & A C C E S S O R I E S

A

Height:

4.0 inches (102 mm)

Width:

8.25 inches (210 mm)

Depth:

8.75 inches (222 mm)

Weight:

2.33 lbs. (1.06 kg)

Shipping

3.4 lbs. (1.5 kg)

Weight:

 

Power

Supplied by printer or auxiliary power supply (5V)

Source:

 

Memory:

Flash; 128K maximum for scripts; 256K maximum for

 

data collection and lookup files. There is no

 

battery-backedRAM.

Operating

40° to 104° F (4° to 40° C) See your printer’s

Limits:

documentation for the printer’s operating range.

A c c e s s o r i e s & O p t i o n s

An optional stand is available for the keyboard. It can be used on a flat surface or mounted on a wall. (Purchase the "keyboard stand" option.) An optional scanner (126743) and a scanner stand (125099), is also available.

Auxiliary 5V Power Supply (126977)

Used with a 9416 or 9825 printer or Non-Monarchprinter.

9 to 9-pinProgramming Cable (126660)

9 to 9-pinCable (126701) used with a 9416 printer

9 to 25-pinCable (126830) used with a 9825 printer

Specifications & Accessories A-1

F l a t S u r f a c e M o u n t

Make sure all surfaces you apply the dual lock fasteners to are free from dirt and oil. If necessary, clean with isopropyl alcohol.

1.Pull the cord through the large hole in the stand.

2.Set the keyboard into the stand.

3.Attach either the rubber pads or dual lock fasteners to the base of the keyboard stand. If using the dual lock fasteners, attach the other side of the fastener to the tabletop.

To remove the keyboard from the stand, lift the keyboard from the bottom.

A-2 Specifications & Accessories

Wa l l M o u n t

1.Hold the bottom of the stand against the wall (hinge side up). Mark the mounting holes with a pencil.

2.Screw the stand onto the wall (screws not included).

3.Pull the cord through the large hole in the stand.

4.Set the keyboard into the stand.

To remove the keyboard from the stand, lift the keyboard from the bottom.

Specifications & Accessories A-3

A-4 Specifications & Accessories

C H A R A C T E R S E T S

B

This appendix contains a listing of the symbol sets and code pages the printer supports.

S u p p o r t e d S y m b o l S e t s a n d C o d e P a g e s

The CG Triumvirate typefaces support only the ANSI and DOS Code Page 437 and 850 Symbol Sets. These fonts print a slashed zero when using the ANSI symbol set. However, the scalable font does not print a slashed zero or support Code Page 1256 (Arabic).

Internal

Use this set to print international monetary

 

symbols, the trademark ( ) symbol, and for

 

formats that may be used on other MPCLII printers.

ANSI

Use this set with proportionally spaced fonts.

DOS Code

Use this set for extended and international

Pages 437 or 850

characters with proportionally spaced fonts.

To enter a character code:

Press and hold a. Use the numeric keys to enter athree-digitcharacter code. For example, pressa 179 for¥ .

The keyboard’s display may not match the character printed.

If you selected monetary signs from the Setup, Defaults menu and use the Standard, Reduced or Bold font, the monetary symbols from the selected country will be printed. However, if using the CG Triumvirate typefaces, the monetary symbols may not print as expected. Make sure your font requirements are supported by the selected code page.

For additional code pages that your printer may support, refer to the Packet Reference Manual available on our Web site (www.paxar.com).

Character Sets B-1

I n t e r n a l ( S t a n d a r d a n d R e d u c e d F o n t )

B-2 Character Sets