Color CCTV Cameras
WV-CP230/WV-CP232/WV-CP234
Before attempting to connect or operate this product, please read these instructions completely.
N1098-0 |
YWV8QA5102AN Printed in Japan |
|
N 30 |
|
|
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is interned to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient
SA 1965 magnitude to constitute a risk of electric shock to persons.
|
The exclamation point within an |
|
equilateral triangle is intended to |
|
alert the user to the presence of |
|
important operating and mainte- |
|
nance (servicing) instructions in the |
|
literature accompanying the appli- |
SA 1966 |
ance. |
|
For U.S.A
Warning:
This equipment generates and uses radio frequency energy and if not installed and used properly, i.e., in strict accordance with the instruction manual, may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.
The serial number of this product may be found on the top of the unit.
You should note the serial number of this unit in the space provided and retain this instruction as a permanent record of your purchase to aid identification in the event of theft.
Model No.
Serial No.
WARNING:
TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
FEATURES
1. The following functions are built in. |
2. |
Minimum illumination of 0.6 lx (0.06 foot-can- |
|
(1) |
Auto Light Control (ALC)/Electronic Light |
|
dle) at F0.75 (equivalent to 2.0 lx (0.2 foot- |
|
Control (ELC) |
|
candle) at F1.4) |
(2) |
Automatic Gain Control (AGC) +15 dB |
|
|
|
and Automatic Tracing White Balance |
3. |
Signal-to-noise ratio of 50 dB |
|
(ATW) |
|
|
(3) |
Camera synchronization mode selec- |
4. |
Horizontal resolution of 480 lines |
|
table between internal (INT), Line-locked |
|
|
|
(LL) and Multiplexed Vertical Drive (VD2) |
5. |
Auto iris lens control selectable between |
|
for WV-CP230 and WV-CP234. |
|
video signal and DC power supply. |
PRECAUTIONS
1. Do not attempt to disassemble the camera. |
5. |
Clean the CCD faceplate with care. |
To prevent electric shock, do not remove |
|
Do not clean the CCD with strong or abrasive |
screws or covers. |
|
detergents. Use lens tissue or a cotton tipped |
There are no user serviceable parts inside. |
|
applicator and ethanol. |
Ask a qualified service person for servicing. |
|
|
|
6. |
Never face the camera towards the sun. |
2.Handle the camera with care.
Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by improper handling or storage.
3.Do not expose the camera to rain or moisture, or try to operate it in wet areas.
Turn the power off immediately and ask a qualified service person for servicing. Moisture can damage the camera and also create the danger of electric shock.
4.Do not use strong or abrasive detergents when cleaning the camera body.
Use a dry cloth to clean the camera when dirty.
In case the dirt is hard to remove, use a mild detergent and wipe gently.
Do not aim the camera at bright objects. Whether the camera is in use or not, never aim it at the sun or other extremely bright objects. Otherwise, blooming or smear may be caused.
7.Do not operate the camera beyond the specified temperature, humidity or power source ratings.
Use the camera under conditions where temperature is between –10°C - +50°C (14°F - 122°F), and humidity is below 90 %. The input power source is 120 V AC 60 Hz for WV-CP230, 12 V DC for WV-CP232, and 24 V AC 60 Hz for WV-CP234.
Caution:
To prevent fire or electric shock hazard, UL listed wire VW-1, style 1007 should be used for the DC 12 V or AC 24 V Input Terminal.
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
<WV-CP230> |
|
||
|
LL |
INT |
WV–CP230 |
|
ELC |
ALC |
|
|
SOFT |
SHARP |
|
|
OFF |
BLC ON |
|
|
DC |
VIDEO |
|
VIDEO OUT |
|
|
|
<WV-CP234> |
|
||
AC 24V IN |
GND |
|
|
|
|
|
|
|
LL |
INT |
|
|
ELC |
ALC |
|
|
SOFT |
SHARP |
|
1 2 |
OFF |
BLC ON |
|
DC |
VIDEO |
|
|
VIDEO OUT
<WV-CP232>
DC 12V IN
ELC 
ALC
SOFT 
SHARP
OFF 
BLC ON
DC 
VIDEO
VIDEO OUT
qAuto Iris Lens Connector
Supplies power and control signals to an auto iris lens (not supplied).
wFlange-back Adjusting Ring
This ring adjusts the back-focal distance or picture focus. Rotate this ring clockwise for a C-mount lens or counterclockwise for a CSmount lens.
e Lens (option)
rCamera Mounting Screw Hole
This hole is for mounting the camera onto a mounting bracket. The camera is originally designed to be mounted from the bottom, but a top-mounting type is also available. To mount from the top, remove the mount adapter from the bottom of the camera by removing two fixing screws. Attach the mount adapter to the top as shown in the diagram, then mount the camera on the mounting bracket. Make sure that two original screws are used when mounting the mount adapter; longer type screws may damage inner components.
tPower Cord (only WV-CP230)
Connect this power cord to an electrical outlet of 120 V AC 60 Hz.
yDC 12 V Input Terminal
(DC 12V IN (only WV-CP232))
This terminal is for connecting the 12 V DC power supply cord.
uAC 24 V Input Terminal
(AC 24V IN (only WV-CP234))
This terminal is for connecting the 24 V AC 60Hz power supply cord.
iSynchronization Mode Selector
(INT, LL (only WV-CP230 and WV-CP234))
Selects the camera synchronization mode from internal sync mode (INT) or line-lock mode (LL).
INT: Sets to internal 2:1 interlace. LL: Sets to Line-lock mode.
oAutomatic Light Control/Electronic Light Control Selector (ALC , ELC)
Lets you select the mode according to the lens type that is used with this camera.
ALC: Select this mode when an auto iris lens (ALC lens) is used with this camera.
ELC: Select this mode when a fixed iris lens or manual iris lens is used with this camera.
!0Detail/Aperture Level Selector
(SOFT/SHARP)
The detail/aperture level can be selected with this selector. Set it to the desired position while observing the picture on the monitor.
SHARP: Normal position.
SOFT: Select this position when a Quad System is connected to this camera.
!1Back Light Compensation Mode Selector
(BLC ON, OFF)
Lets you select the mode according to the position of the object and light conditions on the screen.
ON: Select this mode when a strong light such as a spotlight is in the background.
OFF: Normal picture.
!2Lens Drive Signal Selector (VIDEO, DC)
Lets you select the mode according to the type of auto iris lens drive signal to be supplied to the lens from the auto iris lens connector.
VIDEO: Select this mode if you are using a auto iris lens that requires a video drive signal.
DC: Select this mode if you are using a auto iris lens that requires a DC drive signal.
!3Video Output Connector (VIDEO OUT)
This connector is for connecting with the VIDEO IN connector of the video monitor. Whenever the multiplexed vertical drive (VD2) signal is supplied to this connector, the camera synchronization mode is automatically set to Vertical Drive.
Cautions:
•Connect to 12 V DC (10.5 V-16 V) or 24 V AC (19.5 V-28 V) class 2 power supply only. Make sure to connect the grounding lead to the GND terminal when the power is supplied from a 24 V AC power source.
•To prevent fire or electric shock hazard, UL listed wire VW-1, style 1007 should be used for the DC 12 V or AC 24 V Input Terminal.
Loading...