Panasonic HDC-TM300P, HDC-HS300PC, HDC-HS300P User Manual

Operating Instructions

High Definition Video Camera

Model No. HDC-TM300P/PC

HDC-HS300P/PC

Before connecting, operating or adjusting this product, please read the instructions completely. Spanish Quick Use Guide is included.

Guía para rápida consulta en español está incluida.

For USA and Puerto Rico assistance, please call: 1-800-211-PANA(7262) or, contact us via the web at: http://www.panasonic.com/contactinfo

For Canadian assistance, please call: 1-800-561-5505 or visit us at www.panasonic.ca

VQT1Z09

Things You Should Know

Thank you for choosing Panasonic!

You have purchased one of the most sophisticated and reliable products on the market today. Used properly, we’re sure it will bring you and your family years of enjoyment. Please take time to fill in the information on the right.

The serial number is on the tag located on the back of your camera. Be sure to retain this manual as your convenient camera information source.

Date of Purchase

Dealer Purchased From

Dealer Address

Dealer Phone No.

Model No.

Serial No.

Safety Precautions

WARNING:

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PRODUCT DAMAGE,

≥DO NOT EXPOSE THIS APPARATUS TO RAIN, MOISTURE, DRIPPING OR SPLASHING AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS.

≥USE ONLY THE RECOMMENDED ACCESSORIES.

≥DO NOT REMOVE THE COVER (OR BACK); THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION!

DO NOT INSTALL OR PLACE THIS UNIT IN A BOOKCASE, BUILT-IN CABINET OR IN ANOTHER CONFINED SPACE. ENSURE THE UNIT IS WELL VENTILATED. TO PREVENT RISK OF ELECTRIC SHOCK OR FIRE HAZARD DUE TO OVERHEATING, ENSURE THAT CURTAINS AND ANY OTHER MATERIALS DO NOT OBSTRUCT THE VENTILATION VENTS.

The socket outlet shall be installed near the equipment and easily accessible. The mains plug of the power supply cord shall remain readily operable. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from AC receptacle.

The following mark and symbols are located on bottom of the unit.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE SCREWS. NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

2

VQT1Z09

THE FOLLOWING APPLIES ONLY IN THE U.S.A.

FCC Note:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

≥Reorient or relocate the receiving antenna.

≥Increase the separation between the equipment and receiver.

≥Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

≥Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:	To assure continued compliance, follow the attached installation instructions
	and use only shielded interface cables with ferrite core when connecting to
	computer or peripheral devices.
	Any changes or modifications not expressly approved by the party
	responsible for compliance could void the user’s authority to operate this

	equipment.
Declaration of Conformity
Trade Name:	Panasonic
Model No.:	HDC-TM300P/HDC-HS300P
Responsible party:	Panasonic Corporation of North America
	One Panasonic Way, Secaucus, NJ 07094
Support Contact:	Panasonic Consumer Electronics Company
	1-800-211-PANA (7262)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

HDC-TM300P			HDC-HS300P

THE FOLLOWING APPLIES ONLY IN CANADA.

This Class B digital apparatus complies with Canadian ICES-003.

3

VQT1Z09

Batteries

1 Battery pack (Lithium ion battery pack)

≥Use the specified unit to recharge the battery pack.

≥Do not use the battery pack with equipment other than the specified unit.

≥Do not get dirt, sand, liquids, or other foreign matter on the terminals.

≥Do not touch the plug terminals (i and j) with metal objects.

≥Do not disassemble, remodel, heat or throw into fire.

2 Button-type battery (Lithium battery)

≥Insert with poles aligned.

≥Do not touch the terminals (i and j) with metal objects.

≥Do not recharge, disassemble, remodel, heat or throw into fire.

≥Keep out of reach of children

If any electrolyte should come into contact with your hands or clothes, wash it off thoroughly with water.

If any electrolyte should come into contact with your eyes, never rub the eyes. Rinse eyes thoroughly with water, and then consult a doctor.

Warning

Risk of fire, explosion and burns. Do not disassemble.

Do not heat the batteries above the following temperatures or incinerate.

Button-type battery	60 oC (140 oF)
Battery pack	60 oC (140 oF)

AC adaptor

This AC adaptor operates on AC between 110 V and 240 V.

But

≥In the U.S.A. and Canada, the AC adaptor must be connected to a 120V AC power supply only.

≥When connecting to an AC supply outside of the U.S.A. or Canada, use a plug adaptor to suit the AC outlet configuration.

≥When connecting to a supply of greater than AC 125V, ensure the cord you use is suited to the voltage of the AC supply and the rated current of the AC adaptor.

≥Contact an electrical parts distributor for assistance in selecting a suitable AC plug adaptor or AC cord set.

Product Identification Marking is located on the bottom of units.

U.S.A./CANADA CONSUMERS: ATTENTION:

A lithium ion/polymer battery that is recyclable powers the product you have purchased. Please call 1-800-8-BATTERY for information on how to recycle this battery.

<For USA-California only>

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material – special handling may apply.

See www.dtsc.ca.gov/hazardouswaste/perchlorate.

4

VQT1Z09

IMPORTANT SAFETY INSTRUCTIONS

Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety instructions listed below. Keep these operating instructions handy for future reference.

1)Read these instructions.

2)Keep these instructions.

3)Heed all warnings.

4)Follow all instructions.

5)Do not use this apparatus near water.

6)Clean only with dry cloth.

7)Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8)Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9)Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10)Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11)Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart,

stand, tripod, bracket, or table specified by the manufacturer, or sold

with the apparatus. When a cart is used, use

caution when moving the

cart/apparatus combination to avoid injury from tip-over.

13)Unplug this apparatus during lightning storms or when unused for long periods of time.

14)Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

5

VQT1Z09

Precautions

USE & LOCATION

WARNING

≥TO AVOID SHOCK HAZARD ... Your camera and power supply should not be exposed to rain or moisture. Do not connect the power supply or operate your camera if it gets wet. Your camera has been designed for outdoor use, however it is not designed to sustain direct exposure to water, rain, sleet, snow, sand, dust, or a direct splashing from a pool or even a cup of coffee. This action could permanently damage the internal parts of your camera. Do not attempt to disassemble this unit. There are no user serviceable parts inside. Unplug your camera from the power supply before cleaning.

≥AS WITH ANY SMALL OBJECT, SD CARDS CAN BE SWALLOWED BY YOUNG CHILDREN. DO NOT ALLOW CHILDREN TO HANDLE THE SD CARD.

CAUTION

≥DO NOT AIM YOUR CAMERA AT THE SUN OR OTHER BRIGHT OBJECTS

≥DO NOT LEAVE THE CAMERA WITH THE EVF AIMED DIRECTLY AT THE SUN AS THIS MAY CAUSE DAMAGE TO THE INTERNAL PARTS OF THE EVF

≥DO NOT EXPOSE YOUR CAMERA TO EXTENDED HIGH TEMPERATURE ... Such as, in direct sunlight, inside a closed car, next to a heater, etc... This action could permanently damage the internal parts of your camera.

≥AVOID SUDDEN CHANGES IN TEMPERATURE ... If the unit is suddenly moved from a cold place to a warm place, moisture may form on the SD card and inside the unit.

≥DO NOT LEAVE YOUR CAMERA OR THE POWER SUPPLY TURNED ON WHEN NOT IN USE.

≥STORAGE OF YOUR CAMERA ... Store and handle your camera in a manner that will not subject it to unnecessary movement (avoid shaking and striking). Your camera contains a sensitive pick-up device which could be damaged by improper handling or storage.

6

CARE

≥TO CLEAN YOUR CAMERA ... Do not use strong or abrasive detergents when cleaning your camera body.

≥TO PROTECT THE LENS ... Do not touch the surface of the lens with your hand. Use a commercial camera lens solution and lens paper when cleaning the lens. Improper cleaning can scratch the lens coating.

≥TO PROTECT THE FINISH OF YOUR CAMERA ... Before handling your camera, make sure your hands and face are free from any chemical products, such as suntan lotion, as it may damage the finish.

-If you see this symbol-

Information on Disposal in other Countries outside the European Union

This symbol is only valid in the European Union.

If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.

∫Indemnity concerning recording content

The manufacturer shall in no event be liable for the loss of recordings due to malfunction or defect of this unit, its accessories or recordable media.

IMPORTANT

∫ Carefully observe copyright laws

Whatever you have recorded and created can be used for your personal entertainment only. Under copyright laws, other materials cannot be used without obtaining permission from the holders of the copyrights.

These operating instructions are designed for use with models and . Pictures may be slightly different from the original.

≥The illustrations used in these operating instructions show model ,

VQT1Z09

however, parts of the explanation refer to different models.

≥Depending on the model, some functions are not available.

≥Features may vary, so please read carefully.

∫Cards that you can use with this unit

SD Memory Card and SDHC Memory Card

≥4 GB (or more) Memory Cards that do not have the SDHC logo are not based on SD Memory Card Specifications.

≥Refer to page 28 for more details on SD cards.

∫For the purposes of these operating instructions

≥SD Memory Card and SDHC Memory Card are referred to as the “SD card”.

≥Functions that can be used for motion picture recording/motion picture playback are

indicated by in these operating instructions.

≥Functions that can be used for still picture recording/still picture playback are indicated by in these operating instructions.

≥“HD Writer AE 1.0 for HDC” is referred to as the “HD Writer AE 1.0”.

≥Pages for reference are indicated by an arrow, for example: l 00

∫ Licenses

≥SDHC Logo is a trademark.

≥“AVCHD” and the “AVCHD” Logo are trademarks of Panasonic Corporation and Sony Corporation.

≥Manufactured under license from Dolby Laboratories.

Dolby and the double-D symbol are trademarks of Dolby Laboratories.

≥HDMI, the HDMI Logo and the High-Definition Multimedia Interface are the registered trademarks or trademarks of HDMI Licensing LLC.

≥VIERA Link™ is a trademark of Panasonic Corporation.

≥EZ Sync™ is a trademark of Panasonic Corporation.

≥HDAVI Control™ is a trademark of Panasonic Corporation.

≥“x.v.Color” is trademark.

≥LEICA is a registered trademark of Leica Microsystems IR GmbH and DICOMAR is a registered trademark of Leica Camera AG.

≥Microsoft®, Windows®, Windows Vista® and DirectX® are either registered trademarks or trademarks of the Microsoft Corporation in the United States and/or other countries.

≥Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.

≥IBM and PC/AT are registered trademarks of International Business Machines Corporation of the U.S.

≥Intel®, Core™, Pentium® and Celeron® are the registered trademarks or trademarks of the Intel Corporation in the United States and other countries.

≥AMD Athlon™ is a trademark of the Advanced Micro Devices, Inc.

≥Apple, Mac OS, and iMovie are either registered trademarks or trademarks of Apple Inc. in the United States and/or other countries.

≥PowerPC is a trademark of International Business Machines Corporation.

≥Other names of systems and products mentioned in these instructions are usually the registered trademarks or trademarks of the manufacturers who developed the system or product concerned.

This product is licensed under the AVC patent portfolio license for the personal and noncommercial use of a consumer to (i) encode video in compliance with the AVC Standard (“AVC Video”) and/or (ii) decode AVC Video that was encoded by a consumer engaged in a personal and non-commercial activity and/or was obtained from a video provider licensed to provide AVC Video. No license is granted or shall be implied for any other use. Additional information may be obtained from MPEG LA, LLC. See http://www.mpegla.com.

7

VQT1Z09

Contents
Accessories..................................................	10
Features........................................................	11
Quick Guide..................................................	12
Preparation
Before using
[1] Handling of Built-in Memory and
HDD (Hard disk drive) .......................	15
Handling of built-in memory
[HDC-TM300] ......................................	15
Handling of HDD [HDC-HS300]...........	16
[2] Parts identification and handling.....	17
[HDC-TM300] ......................................	17
[HDC-HS300].......................................	20
Setup
[1] Power supply .....................................	23
Charging the battery ............................	23
Inserting/removing the battery .............	24
Charging and recording time ...............	25
Connecting to the AC outlet.................	27
[2] Preparation of SD cards....................	28
Cards that you can use with this unit ....	28
Inserting/removing an SD card ............	29
[3] Selecting a mode
(Turning the unit on/off) ....................	30
Turning the power on and off with the
LCD monitor/viewfinder .......................	31
[4] How to use the touch screen............	32
[5] Using the menu screen .....................	33
Using the quick menu ..........................	34
Language selection .............................	35
Menu list ..............................................	35
[6] Setting date and time ........................	39
World time setting (Displaying the
time of the travel destination) ..............	40
[7] Adjusting LCD monitor/viewfinder ....	41
LCD monitor adjustment......................	41
Touch screen calibration......................	42
Viewfinder adjustment .........................	42
Recording showing the contents to a
partner .................................................	43
[8] Using with the remote control..........	44
Operation of direction buttons/
OK button ............................................	45

	Recording
Recording (Basic)
[1]	Before recording ...............................	46
	Intelligent auto mode...........................	47
	Quick start ...........................................	49
	Quick power on ...................................	50
[2]	Recording motion pictures ..............	51
	Recording modes/approximate
	recordable time ...................................	53
	PRE-REC ............................................	54
	Shooting guide ....................................	54
[3]	Recording still pictures ....................	55
	Aspect ratio/Picture size......................	56
	Picture quality......................................	57
	Recording still pictures in Motion
	Picture Recording Mode......................	57
	Number of recordable pictures............	58
[4]	Zoom in/out function ........................	61
	Digital zoom function...........................	61
	Ring zoom ...........................................	61
	Extra Optical Zoom .............................	62
[5] Optical image stabilizer function.....		63
[6]	AF tracking ........................................	64
Recording (Advanced)
[1] Recording functions of operation
	icons...................................................	66
	Operation icons ...................................	66
[2] Recording functions of menus ........		70
[3] Recording manually by setting
	white balance, shutter speed or
	iris adjustment...................................	82
	White balance .....................................	83
	Manual shutter speed/iris
	adjustment...........................................	84
[4] Recording with manual focus ..........		85
[5] Recording manually by setting
	the menu ............................................	86
	Picture adjustment ..............................	86

8

VQT1Z09

	Playback
Playback
[1]	Motion picture playback ...................	87
	Creating still picture from motion
	picture..................................................	90
	Highlight&Time frame index.................	90
	Playing back motion pictures by date....	91
	Intelligent scene selection ...................	91
	Highlight playback ...............................	92
	Repeat playback..................................	93
	Resuming the previous playback.........	93
[2]	Still picture playback.........................	94
	Playing back still pictures by date........	96
Editing
[1]	Deleting scenes/still pictures ...........	97
[2] Dividing a scene to partially delete ....		99
[3]	Protecting scenes/still pictures .....	100
[4]	DPOF setting....................................	101
[5] Copying between SD card and
	Built-in Memory/HDD.......................	102
	Confirming remaining capacity on the
	copy destination.................................	102
	Copying .............................................	103
[6]	Relay scene combining
	[HDC-TM300] ....................................	105
[7]	Formatting........................................	106
With a TV
[1]	Watching Video/Pictures on
	your TV .............................................	107
	Connecting with a HDMI mini cable....	110
	Listening in 5.1 channel sound ..........	111
	Connecting with the component
	cable ..................................................	111
[2] Playback using VIERA Link™
	(HDAVI Control™).............................	112
	Backup
With other products
[1] Connecting a DVD burner to copy to/
	play back a disc ...............................	114
	Preparing for copying/playing back.....	114
	Copying to discs ................................	116
	Playing back the copied disc .............	119
	Managing the copied disc
	(Formatting, Auto protect,
	Displaying disc information)...............	120
[2] Dubbing images onto other video
	devices .............................................	121
[3] With a printer (PictBridge) ..............		122

With a PC

Before using

[1]	What you can do with a PC ............	125
	End User License Agreement ...........	127
[2]	Operating environment...................	128

Setup		135		Preparation
	About the PC display .........................
[1]	Installation .......................................	131
[2] Connecting to a PC.........................		133
Using with a PC
[1] Starting HD Writer AE 1.0		136
	Reading the operating instructions of			Recording
	the software applications ...................	136
[2]	If using Macintosh	137
	Others
Indications
[1]	Indications	138
[2]	Messages .........................................	141		Playback
	About recovery ..................................	142
Helpful hints
[1] Functions that cannot be used
	simultaneously ................................	143
[2]	Troubleshooting ..............................	146
Cautions for use		153
Specifications ............................................		156
Optional accessories ................................		160		Backup
	Accessory Order Form (For USA and
	Puerto Rico Customers) ....................	162
Request for Service Notice (USA and
Puerto Rico Only)......................................		163
Limited Warranty (United States and
Puerto Rico)		164
Customer Services Directory				a PC
(United States and Puerto Rico)...............		165
Warranty (For Canadian Customers).......		166
Index		167		With
	...........................................................
Spanish Quick Use Guide/Guía española
para el .....................................uso rápido		169
				Others

9

VQT1Z09

Accessories

Check the accessories before using this unit.

Battery pack

VW-VBG130

AC adaptor

VSK0697

AC cable

K2CA2CA00025

DC cable

K2GJYDC00004

Remote control (Built-in battery)

N2QAEC000024

AV cable

K2KYYYY00054

Component cable

K1HY10YY0005

USB cable

K1HY04YY0032

Stylus pen

VFC4394

Shoe adaptor

(supplied for HDC-TM300; not supplied for HDC-HS300) VYC0996

CD-ROM

10

VQT1Z09

Features

∫ Very clear high definition pictures

This unit can record detailed high definition images.

High definition images (1920k1080)*			Standard images (720k480)
A Number of available scan lines 1080			B Number of available scan lines 480
* If the recording mode is HA/HG/HX.

What is AVCHD?

This is a format for recording and playing back highly detailed high definition images.

Images are recorded based on the MPEG-4 AVC/H.264 codec for compressing images and audio is recorded with the Dolby Digital 5.1 Creator.

≥ Since the recording method is different from an ordinary DVD video etc., the data is not compatible.

∫ Compatibility with other products

	With other products	Available function	Picture quality
	Watching Video/	Playback with the HDMI mini cable	High definition
	Pictures on your TV	jPlayback using VIERA Link™ (HDAVI	images
	(l 107 to 113)	Control™) (l 112)
		Playback with the component cable [1080i]
		Playback with the component cable [480i]	Standard images
		Playback with the AV cable
	Using a DVD burner	Connecting a DVD burner to copy to/play back a	High definition
	(l 114 to 120)	disc	images
		jPlaying back the copied disc (l 119)	Standard images
	What you can do with a	Copying data to a PC and editing	High definition
	PC		images
		Writing data to BD/DVD discs and SD cards
	(l 125 to 126)
		Converting the motion picture data to MPEG2	Standard images
		Creating a DVD Video disc
	Dubbing images onto	Dubbing images when connecting with the AV cable	Standard images
	other video devices
	(l 121)

11

VQT1Z09

Quick Guide

∫ Charging the battery

Charging lamp [CHARGE] A

Lights up:

Charging

Goes off:

Charging completed

1Connect the AC cable to the AC adaptor and the AC outlet.

2Insert the battery into the AC adaptor by aligning the arrows.

∫ Inserting the battery

Install the battery by inserting it in the direction shown in the figure.

A Insert the battery until it clicks and locks.

∫ Inserting/removing an SD card

OPEN

1) Open the LCD monitor.

≥ Check that the access lamp has gone off.

2)Open the SD card cover by sliding the OPEN lever B.

3)Insert/remove the SD card.

≥Face the label side C in the direction shown in the illustration and press it straight in as far as it will go.

≥Press the center of the SD card and then pull it straight out.

4) Securely close the SD card cover. ≥ Securely close it until it clicks.

∫ How to turn on the power

Turn on the power by changing the mode to ,

or while pressing the lock release button A.

HDC-TM300

≥Rotate the mode dial while at the same time pressing in the lock release button if changing from OFF to another mode.

≥Align with B.

≥Status indicator C

HDC-HS300

OFF

≥Rotate the mode dial while at the same time pressing in the lock release button if changing from OFF to another mode.

≥Align with B.

≥Status indicator C

Access lamp [ACCESS] A

≥When this unit is accessing the SD card or built-in memory, the access lamp lights up.

12

≥ To turn off the power, change the mode to OFF.

VQT1Z09

∫ How to use the touch screen

You can operate by directly touching the LCD monitor (touch screen) with your finger.

It is easier to use the stylus pen (supplied) for detailed operation or if it is hard to operate with your fingers.

Touch and release the touch screen to select icon or picture.

∫ Recording motion pictures

1)Change the mode to .

2)Open the LCD monitor or extend the viewfinder.

3)

Press the MENU button, then touch [MEDIA SELECT] # [Built-in Memory] or [SD CARD].

Press the MENU button, then touch [MEDIA SELECT] # [HDD] or [SD CARD].

4)Press the recording start/stop button to start recording.

∫ Language selection

1)Press the MENU button, then touch [SETUP]

# [LANGUAGE].

2)Touch [English].

	∫	Recording still pictures
	1)	Change the mode to			.
	2)	Open the LCD monitor or extend the
	3)	viewfinder.
		Press the MENU button, then touch
		[MEDIA SELECT] # [Built-in Memory] or
		[SD CARD].
		Press the MENU button, then touch
		[MEDIA SELECT] # [HDD] or [SD CARD].
	4)	Press the	button fully to take the picture.

13

VQT1Z09

∫ Motion picture playback

1)Change the mode to .

2)Touch the play mode select icon A to select desired media to be played back.

≥Touch [VIDEO/SD CARD] to play back the SD card.

Touch [VIDEO/Built-in Memory] to play back the built-in memory.

Touch [VIDEO/HDD] to play back the HDD. 3) Touch the scene to be played back.

4)Select the playback operation by touching the operation icon.

0h00m00s

1/;: Playback/Pause

6: Rewind playback

5: Fast forward playback

∫: Stops the playback and shows the thumbnails.

∫ Still picture playback

1)Change the mode to .

2)Touch the play mode select icon A to select desired media to be played back.

≥Touch [PICTURE/SD CARD] to play back the SD card.

Touch [PICTURE/Built-in Memory] to play back the built-in memory.

Touch [PICTURE/HDD] to play back the HDD. 3) Touch the still picture to be played back.

4)Select the playback operation by touching the operation icon.

1/;: Slide show (playback of the still pictures in numerical order) start/pause.

2;: Plays back the previous picture. ;1: Plays back the next picture.

∫: Stops the playback and shows the thumbnails.

14

VQT1Z09

Preparation

	Before using	Handling of Built-in Memory
		1 and HDD (Hard disk drive)

:

This unit is equipped with the built-in 32 GB memory. When using this component, pay attention to the following points.

:

This unit is equipped with the built-in 120 GB HDD. While the HDD is capable of storing a large amount of data, there are a few things to look out for. When using this component, pay attention to the following points.

Indemnity about recorded content

Panasonic does not accept any responsibility for damages directly or indirectly due to any type of problems that result in loss of recording or edited content, and does not guarantee any content if recording or editing does not work properly. Likewise, the above also applies in a case where any type of repair is made to the unit (including any other non-built-in memory/HDD related component).

Handling of built-in memory [HDC-TM300]

∫ Back up data periodically.

The built-in memory is temporary storage. In order to avoid erasing data due to static electricity, electromagnetic waves, breakage, and failures, back up the data to a PC or DVD disc. (l 114, 125)

∫ Access lamp [ACCESS] A

≥The lamp illuminates while the SD card or built-in memory is being accessed (initialization, recording, playback, deleting etc.).

≥Do not perform the following operations when the lamp illuminates. It may damage the built-in memory or cause a malfunction in the unit.

jTurn the unit off

jInsert and remove the USB cable jExpose the unit to vibrations or shock

≥About disposing of or giving away this unit. (l 154)

15

VQT1Z09

Handling of HDD [HDC-HS300]

∫Do not expose the HDD to vibrations and shocks.

Due to the environment and handling conditions, the HDD may be subject to partial damages or may not be able to read, record, and play back data. Do not expose the unit to vibrations or shock, and do not turn off the power during recording or playback.

If the unit is used in a place with loud sounds, such as a club or similar venue, the recording may stop due to sound vibrations. Recording data on an SD card is recommended in these places.

∫ Back up data periodically.

The HDD is temporary storage. In order to avoid erasing data due to static electricity, electromagnetic waves, breakage, and failures, back up the data to a PC or DVD disc. (l 114, 125)

∫If the HDD experiences any abnormality, back up data immediately.

Failure in the HDD may produce continuous noise or choppy sound during recording or playing back. Continuous use will cause further deterioration, and may eventually disable the HDD. If these phenomena are observed, copy the data on the HDD to a PC, a DVD disc etc. immediately and contact consumer support. (l 165, 166)

Once the HDD is out of order, data cannot be restored.

∫Operation may stop in hot or cold environments.

The unit is disabled in order to protect the HDD.

∫Do not use the unit in low atmospheric pressures.

The HDD may fail if it is used at altitudes of 3000 m (9800 feet) or higher above sea level.

∫ Transportation

When the unit is transported, turn off the power and be careful not to shake, drop, or cause impact to the unit.

16

∫ Falling detection

[ ] is indicated on the screen when it detects a falling state (a weightless state). If the falling state is detected repeatedly, the unit may stop the recording or playback operation in order to protect the HDD.

∫HDD access lamp [ACCESS HDD]

A

≥The lamp illuminates while the HDD is being accessed (initialization, recording, playback, deleting etc.).

≥Do not perform the following operations when the lamp illuminates. It may damage the HDD or cause a malfunction in the unit.

jTurn the unit off

jInsert and remove the USB cable jExpose the unit to vibrations or shock

≥About disposing of or giving away this unit. (l 154)

VQT1Z09

Preparation

Before using		2		Parts identification and
				handling
	[HDC-TM300]
		1		2		3		4		5

				6
				7
				8
10	11 12 13 14 15
	19	A/V
	20			9
	21	16	17
				18

1 LCD monitor (Touch screen) (l 32, 41)

≥It can open up to 90o.

≥It can rotate up to 180o A towards the lens or 90o B towards the viewfinder.

Due to limitations in LCD production technology, there may be some tiny bright or dark spots on the LCD monitor screen. However, this is not a malfunction and does not affect the recorded picture.

2Optical image stabilizer button [, O.I.S.] (l 63)

3 Inlet (cooling fan)

≥The cooling fan rotates to prevent the internal temperature from rising. Take care not to cover the inlet when using this unit.

4Intelligent auto button [iA] (l 47)

5PRE-REC button [PRE-REC] (l 54)

6Eyepiece corrector dial (l 42)

7Battery holder (l 24)

8DC input terminal [DC IN] (l 27)

≥ Always use the supplied AC adaptor or a genuine Panasonic AC adaptor (VW-AD21PP; optional).

9USB terminal [ ] (l 114, 122, 133)

10Quick menu button [Q.MENU] (l 34)

11Sub recording start/stop button (l 46)

≥This button functions in the same manner as the recording start/stop button.

12Zoom buttons (l 61)

≥These buttons function in the same manner as the zoom lever. Changing the thumbnail display and adjusting the volume can be done.

13Menu button [MENU] (l 33)

17

VQT1Z09

14Delete button [ ] (l 97)

15SD card open lever [OPEN] (l 29)

16Audio-video output terminal [A/V] (l 107, 121)

≥Use the AV cable (only the supplied cable).

17Component terminal [COMPONENT] (l 107)

18HDMI mini connector [HDMI] (l 107, 112)

19Access lamp [ACCESS] (l 15, 29)

20Card slot (l 29)

21SD card cover (l 29)

27Remote control sensor (l 45)

28Recording lamp (l 36)

29 30

31

22	23		32
	24	29	Built-in flash (l 68)
	25	30	Lens (LEICA DICOMAR)
		31	Lens hood
		Rotate the lens hood counter-clockwise A to
	26	remove it. In order to attach it, place into slot B,
		and then rotate it clockwise C.
	27
	28

22 Lens cover

≥The lens cover opens in Motion Picture Recording Mode or Still Picture Recording

Mode. (l 30)

23Multi manual ring (l 82)

24Speaker

25Manual focus button [FOCUS] (l 85)

26Manual function button [FUNCTION] (l 86)

≥When fitting the tele conversion lens (VW-T4314H; optional) or the wide conversion

lens (VW-W4307H; optional), first remove the lens hood.

32 AF assist lamp (l 79)

38	39	40
37
36		41
		42
35
34		MIC
33
		43
		44
	46	45

33Mode dial (l 30)

34Recording start/stop button (l 51)

35Status indicator (l 30)

36 Viewfinder (l 42)

Due to limitations in LCD production technology, there may be some tiny bright or dark spots on the viewfinder screen. However, this is not a malfunction and does not affect the recorded picture.

18

VQT1Z09

37Photoshot button [ ] (l 55)

38Zoom lever [W/T] (In Recording Mode) (l 61)

Thumbnail display switch/Volume lever [s /VOLr] (In Playback Mode) (l 88)

39Internal microphones (5.1 channel support)

40Shoe adaptor mounting part

41Shoe adaptor cover

42Shoe adaptor release lever [SHOE ADAPTOR RELEASE]

The video DC light/VW-LDC103PP (optional) etc. can be mounted on the shoe adaptor (supplied).

1 Open the shoe adaptor cover.

2 Attach the shoe adaptor to this unit, and close the cover.

3 Attach the video DC light to this unit.

≥When removing the shoe adaptor, slide the SHOE ADAPTOR RELEASE lever, and remove the shoe adaptor while sliding the lever.

43 Microphone terminal [MIC]

≥A compatible plug-in powered microphone can be used as an external microphone.

≥Audio will be stereo (2 ch) with the external microphone input.

≥When the unit is connected with the AC adaptor, sometimes noise may be heard depending on the microphone type. In this case, please switch to the battery for the power

supply and the noise will stop.

44Headphone terminal [ ] (l 69)

45Grip belt

Adjust the length of the grip belt so that it fits your hand.

1 Flip the belt.

2 Adjust the length.

3 Replace the belt.

46 Shoulder strap fixture

47 48

47Battery release lever [BATT] (l 24)

48Tripod receptacle

This is a hole for attaching the unit to the optional tripod. (For details on mounting the tripod, refer to the operating instructions for the tripod.)

A Camera base

19

VQT1Z09

[HDC-HS300]

1

2

3

4

5

6

7

8

10 11 12 13 14 15

	19	A/V
	20			9
	21	16	17
				18

1 LCD monitor (Touch screen) (l 32, 41)

≥It can open up to 90o.

≥It can rotate up to 180o A towards the lens or 90o B towards the viewfinder.

Due to limitations in LCD production technology, there may be some tiny bright or dark spots on the LCD monitor screen. However, this is not a malfunction and does not affect the recorded picture.

2Optical image stabilizer button [ , O.I.S.] (l 63)

3Inlet (cooling fan)

≥The cooling fan rotates to prevent the internal temperature from rising. Take care not to cover

the inlet when using this unit.

4 Intelligent auto button [iA] (l 47)

5PRE-REC button [PRE-REC] (l 54)

6Eyepiece corrector dial (l 42)

7Battery holder (l 24)

8DC input terminal [DC IN] (l 27)

≥Always use the supplied AC adaptor or a genuine Panasonic AC adaptor (VW-AD21PP;

optional).

9USB terminal [ ] (l 114, 122, 133)

10Quick menu button [Q.MENU] (l 34)

11Sub recording start/stop button (l 46)

≥This button functions in the same manner as the recording start/stop button.

12Zoom buttons (l 61)

≥These buttons function in the same manner as the zoom lever. Changing the thumbnail display and adjusting the volume can be done.

13Menu button [MENU] (l 33)

14Delete button [ ] (l 97)

15SD card open lever [OPEN] (l 29)

16Audio-video output terminal [A/V] (l 107, 121)

≥Use the AV cable (only the supplied cable).

17Component terminal [COMPONENT] (l 107)

18HDMI mini connector [HDMI] (l 107, 112)

19Access lamp [ACCESS] (l 29)

20Card slot (l 29)

21SD card cover (l 29)

20

VQT1Z09

23 24

25

26 27

22

28

29

30

22 Lens cover

≥The lens cover opens in Motion Picture Recording Mode or Still Picture Recording

Mode. (l 30)

23Internal microphones (5.1 channel support)

24Multi manual ring (l 82)

25Speaker

26Accessory shoe

≥The video DC light/VW-LDC103PP (optional) etc. can be mounted here.

31 32

33

34

31Built-in flash (l 68)

32Lens (LEICA DICOMAR)

33Lens hood

Rotate the lens hood counter-clockwise A to remove it. In order to attach it, place into slot B, and then rotate it clockwise C.

≥When fitting the tele conversion lens (VW-T4314H; optional) or the wide conversion lens (VW-W4307H; optional), first remove the

lens hood.

34 AF assist lamp (l 79)

27Manual focus button [FOCUS] (l 85)

28Manual function button [FUNCTION] (l 86)

29Remote control sensor (l 45)

30Recording lamp (l 36)

21

VQT1Z09

39 40 41

38

37

36

35

45 44

35Recording start/stop button (l 51)

36HDD access lamp [ACCESS HDD] (l 16)

37Viewfinder (l 42)

Due to limitations in LCD production technology, there may be some tiny bright or dark spots on the viewfinder screen. However, this is not a malfunction and does not affect the recorded picture.

38Mode dial (l 30)

39Photoshot button [ ] (l 55)

40Zoom lever [W/T] (In Recording Mode) (l 61) Thumbnail display switch/Volume lever [s /VOLr] (In Playback Mode) (l 88)

41Status indicator (l 30)

42Microphone terminal [MIC]

≥A compatible plug-in powered microphone can be used as an external microphone.

≥Audio will be stereo (2 ch) with the external microphone input.

≥When the unit is connected with the AC adaptor, sometimes noise may be heard depending on the microphone type. In this case, please switch to the battery for the power

supply and the noise will stop.

43Headphone terminal [] (l 69)

44Grip belt

Adjust the length of the grip belt so that it fits your hand.

1 Flip the belt.

2 Adjust the length.

3 Replace the belt.

MIC

42

43

45 Shoulder strap fixture

46 47

46Battery release lever [BATT] (l 24)

47Tripod receptacle

This is a hole for attaching the unit to the optional tripod. (For details on mounting the tripod, refer to the operating instructions for the tripod.)

A Camera base

22

VQT1Z09

Preparation

Setup	1 Power supply

∫ About batteries that you can use with this unit

The battery that can be used with this unit is VW-VBG130/VW-VBG260/VW-VBG6.

≥This unit has a function to distinguish the batteries that can be used, and the batteries (VW-VBG130/VW-VBG260/VW-VBG6) are compatible with this function. (The batteries that are not compatible to this function cannot be used.)

≥To use the VW-VBG6 for this unit, the battery pack holder kit VW-VH04 (optional) is required.

It has been found that counterfeit battery packs which look very similar to the genuine product are made available to purchase in some markets. Some of these battery packs are not adequately protected with internal protection to meet the requirements of appropriate safety standards. There is a possibility that these battery packs may lead to fire or explosion. Please be advised that we are not liable for any accident or failure occurring as a result of use of a counterfeit battery pack. To ensure that safe products are used we would recommend that a genuine Panasonic battery pack is used.

Charging the battery

When this unit is purchased, the battery is not charged. Charge the battery before using this unit.

Important:

If the DC cable is connected to the AC adaptor, then the battery will not charge. Remove the DC cable from the AC adaptor.

Charging lamp [CHARGE] A

Lights up:

Charging (Battery charging time: l 25)

Goes off:

Charging completed

Flashing:

Make sure that the terminals of the battery or the AC adaptor are not exposed to dirt, foreign objects or dust, then reconnect them properly. (l 155)

1 Connect the AC cable to the AC adaptor and the AC outlet.

2 Insert the battery into the AC adaptor by aligning the arrows.

23

VQT1Z09

≥We recommend using Panasonic batteries (l 10, 25, 160).

≥If you use other batteries, we cannot guarantee the quality of this product.

≥Do not heat or expose to flame.

≥Do not leave the battery(ies) in an automobile exposed to direct sunlight for a long period of time with doors and windows closed.

Inserting/removing the battery

Install the battery by inserting it in the direction shown in the figure.

Removing the battery

Make sure that the power is off and that the status indicator is turned off, and then remove by holding onto it taking care not to drop.

Move the BATTERY lever in the direction indicated by the arrow and remove the battery when unlocked.

A Insert the battery until it clicks and locks.

BATT

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

24

VQT1Z09

Charging and recording time

∫ Charging/Recording time

≥Temperature: 25 oC (77 oF)/humidity: 60%

≥When using the viewfinder (times in parentheses are when using the LCD monitor)

HDC-TM300

Battery model number

Charging time

Maximum

Actual recordable

[Voltage/Capacity

continuously

time

(minimum)]

recordable time

Supplied battery/

1 h 45 min

1 h 5 min

VW-VBG130 (optional)

2 h 35 min

(1 h 40 min)

(1 h)

[7.2 V/1250 mAh]

VW-VBG260 (optional)

4 h 40 min

3 h 20 min

2 h 5 min

[7.2 V/2500 mAh]

(3 h 15 min)

(2 h)

VW-VBG6 (optional)*

9 h 25 min

8 h 20 min

5 h 10 min

[7.2 V/5400 mAh]

(8 h)

(4 h 55 min)

HDC-HS300

Battery model

Charging

Recording

Recording

Maximum

Actual

number

continuously

recordable

[Voltage/Capacity

time

destination

mode

recordable time

time

(minimum)]

Supplied battery/

HDD

HA/HG/HX/

1 h

35 min

1 h

VW-VBG130

2 h 35 min

HE

(1 h

30 min)

(55 min)

(optional)

SD

HA/HG/HX/

1 h

40 min

1 h

[7.2 V/1250 mAh]

HE

(1 h

35 min)

(1 h)

HA/HG/HX

3 h 5 min

1 h 55 min

(2 h

55 min)

(1 h 50 min)

VW-VBG260

HDD

3 h 5 min

1 h 55 min

(optional)

4 h 40 min

HE

(3 h)

(1 h 50 min)

[7.2 V/2500 mAh]

SD

HA/HG/HX/

3 h

15 min

2 h

HE

(3 h 5 min)

(1 h 55 min)

HA/HG/HX

7 h

40 min

4 h 45 min

(7 h

20 min)

(4 h 30 min)

VW-VBG6

HDD

7 h

45 min

4 h 45 min

(optional)*

9 h 25 min

HE

(7 h

25 min)

(4 h 35 min)

[7.2 V/5400 mAh]

SD

HA/HG/HX/

8 h 5 min

5 h

HE

(7 h

45 min)

(4 h 45 min)

* The battery pack holder kit VW-VH04 (optional) is necessary.

≥These times are approximations.

≥The indicated charging time is for when the battery has been discharged completely. Charging time and recordable time vary depending on the usage conditions such as high/low temperature.

25

VQT1Z09

≥The actual recordable time refers to the recordable time when repeatedly starting/stopping recording, turning the unit on/off, moving the zoom lever etc.

≥The batteries heat up after use or charging. This is not a malfunction.

Battery capacity indication

≥The display changes as the battery capacity reduces. #### If there is less than 3 minutes remaining, then will become red. If the battery discharges, then ( ) will flash.

≥The remaining battery capacity is displayed when using the Panasonic battery that you can use for this unit. It may take time to display the remaining battery capacity. The actual time can vary depending on your actual use.

≥The maximum amount of remaining battery capacity able to be indicated is 9 hours 59 minutes. If the actual remaining time exceeds 9 hours 59 minutes, the indication will stay green and will not change until the remaining time falls below 9 hours 59 minutes.

≥When changing modes, the time indication will turn off momentarily in order to recalculate the remaining battery capacity time.

≥When using the AC adaptor or batteries made by other companies, the remaining battery capacity will not be shown.

26

VQT1Z09

Connecting to the AC outlet

Important:

While the DC cable is connected to the AC adaptor, the battery will not charge.

≥Do not use the AC cable with any other equipment as it is designed only for this unit. Also, do not use the AC cable from other equipment with this unit.

DC IN

A DC output terminal

BDC input terminal

Insert the DC cable matching the [] mark of the DC input terminal.

1 Connect the AC cable to the AC adaptor and the AC outlet.

2 Connect the DC cable to the AC adaptor.

3 Connect the DC cable to the DC input terminal [DC IN].

≥Make sure to set the mode to OFF and that the status indicator is turned off when disconnecting the AC adaptor.

27

VQT1Z09

Preparation

Setup	2 Preparation of SD cards

This unit (an SDHC compatible device) is compatible with both SD Memory Cards and SDHC Memory Cards. When using an SDHC Memory Card on another device, confirm that the device supports the SDHC Memory Card.

Cards that you can use with this unit

Use SD cards conforming to Class 4 or higher of the SD Speed Class Rating* for motion picture recording.

	Card type	Capacity	Motion picture recording	Still picture
			The following models of Panasonic SD cards can
				recording
			be used.
		8 MB	Cannot be used.	Can be
		16 MB		used.
		32 MB	Cannot be guaranteed in operation.
	SD Memory	64 MB	The recording may suddenly stop during motion
		128 MB	picture recording depending on the SD card you
	Card	256 MB	use. (l 147)
		512 MB
		1 GB	RP-SDV01G
		2 GB	RP-SDV02G, RP-SDM02G
		4 GB	RP-SDV04G, RP-SDM04G
		6 GB	RP-SDM06G
	SDHC
		8 GB	RP-SDV08G
	Memory
		12 GB	RP-SDM12G
	Card
		16 GB	RP-SDV16G
		32 GB	RP-SDV32G

* The SD Speed Class Rating is the speed standard for successive writes.

≥4 GB or more Memory Cards that do not have the SDHC logo are not based on SD Memory Card Specifications.

≥ When the write-protect
switch A on SD card is
locked, no recording,	32
deletion or editing will be

possible on the card.

≥Keep the Memory Card out of reach of children to prevent swallowing.

28

VQT1Z09

Inserting/removing an SD card

When using an SD card not from Panasonic, or one previously used on other equipment, for the first time on this unit, format the SD card. (l 106) When the SD card is formatted, all of the recorded data is deleted. Once the data is deleted, it cannot be restored. Copy valuable data onto a PC, DVD disc etc. before proceeding with the formatting. (l 114, 125)

Caution:

When the SD card is removed while the access lamp is lit, this unit may malfunction or the data recorded on the SD card may be lost.

Access lamp [ACCESS] A

≥ When this unit is accessing the SD card or built-in memory, the access lamp lights up.

1 Open the LCD monitor.

≥ Check that the access lamp has gone off.

2 Open the SD card cover by sliding the OPEN lever B.

OPEN	3 Insert/remove the SD card.

≥ Face the label side C in the direction shown in the illustration and press it straight in as far as it will go.

≥ Press the center of the SD card and then pull it straight out.

4 Securely close the SD card cover.

≥ Securely close it until it clicks.

≥Do not touch the terminals on the back of the SD card.

≥Do not apply strong shocks, bend, or drop the SD card.

≥Electrical noise, static electricity or the failure of this unit or the SD card may damage or erase the data stored on the SD card.

≥When the card access lamp is lit, do not: jRemove the SD card

jTurn the unit off

jInsert and remove the USB cable jExpose the unit to vibrations or shock

Performing the above while the lamp is on may result in damage to data/SD card or this unit.

29

VQT1Z09

Preparation

	Setup	Selecting a mode
		3 (Turning the unit on/off)

Change the mode to recording, playback or power OFF.

Turn on the power by changing the mode to , or while pressing the lock release button A.

HDC-TM300

HDC-HS300

≥Rotate the mode dial while at the same time pressing in the lock release button if changing from OFF to another mode.

≥Align with B.

≥Status indicator C

The status indicator lights.

≥Rotate the mode dial while at the same time pressing in the lock release button if changing from OFF to another mode.

≥Align with B.

≥Status indicator C

To turn off the power

Change the mode to OFF.

The status indicator goes off.

Motion Picture Recording Mode (l 51)

Still Picture Recording Mode (l 55)

Playback Mode (l 87, 94)

OFF

30

VQT1Z09