Industrial Camera
GP-MF602
Before attempting to connect or operate this product, please read these instructions completely.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclo-
SA 1965 sure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
|
The exclamation point within an |
|
equilateral triangle is intended to |
|
alert the user to the presence of |
|
important operating and mainte- |
|
nance (servicing) instructions in the |
SA 1966 |
literature accompanying the appli- |
ance. |
Warning:
This equipment generates and uses radio frequency energy and if not installed and used properly, i.e., in strict accordance with the instruction manual, may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CONTENTS |
|
PREFACE ....................................................... |
1 |
FEATURES ..................................................... |
1 |
PRECAUTIONS .............................................. |
2 |
MAJOR OPERATING CONTROLS AND |
|
THEIR FUNCTIONS ........................................ |
3 |
PREPARATIONS ............................................. |
7 |
SYSTEM CONNECTIONS ............................... |
8 |
INSTALLATION OF CAMERA ......................... |
9 |
EXTERNAL SYNCHRONIZATION ................ |
10 |
PREVENTION OF BLOOMING AND SMEAR .. |
10 |
SPECIFICATIONS ......................................... |
11 |
OPTIONAL ACCESSORIES ........................... |
12 |
Remove dust on the faceplate of filter glass before mounting the lens on the camera.
The serial number of this product may be found on the bottom of the unit.
You should note the serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft.
Model No.
Serial No.
PREFACE
The Panasonic GP-MF602 Industrial Camera incorporates a Inter Line Transfer type CCD image sensor.
The GP-MF602 further has an image sensor of 380,000 pixels and 570 lines of horizontal resolution, with smear reduced to a bare minimum.
FEATURES
1.Newly developed multi-function solid state image sensor 1/2” Inter Line Transfer type CCD image sensor with 768 (H) x 494 (V) pixels.
2.Selectable scanning system :
1-line interlace, 2-line interlace and 2-line sequential are available for the highest quality possible within video processing.
3.External synchronization :
External HD and VD input enable system set-up with external video processors, etc.
4.Frame Reset :
External HD and VD reset signals reset the scanning line to the line number 1.
5.Seven-step of Electronic Shutter or threestep of Electronic Shutter with trigger function selectable.
- 1 -
PRECAUTIONS
1.Do not attempt to disassemble the camera. To prevent electric shock, do not remove screws or cover. There are no user-service- able parts inside. Refer servicing to qualified service personnel.
2.Do not expose the camera to rain or moisture, and avoid operation in wet areas.
Take immediate action if the camera should become wet. Turn the power off and request servicing from qualified service personnel. Moisture can damage the camera and create danger of electric shock.
3.Do not drop anything inside the camera. Dropping metal for example inside the camera could permanently damage the unit. If anything is dropped inside the camera, turn off the power immediately and refer to the qualified service personnel.
4.Never aim the camera at bright objects. Whether the camera is in use or not, never aim it at the sun, or other extremely bright objects as this could cause blooming.
5.Do not use the camera beyond its temperature, humidity or power source ratings. This camera is designed for indoor use.
(a)The ambient temperature must not range beyond 14˚F - 122˚F (− 10˚C - +50˚C).
(b)Avoid using the camera when the humidity is above 90%.
(c)The input power source must be DC 12V, 190mA.
- 2 -
Loading...