Panasonic ES8075 N User Manual

0 (0)

IN USA CONTACT:

Panasonic Consumer Electronics Company Division of Panasonic Corporation of North America

One Panasonic Way 2F-3 Secaucus, NJ 07094

IN PUERTO RICO CONTACT: Panasonic Sales Company Division of Panasonic Corporation of Puerto Rico, Inc.

San Gabriel Industrial Park 65 Carolina, Puerto Rico 00630

IN CANADA CONTACT: AU CANADA, CONTACTER: Panasonic Canada Inc.

5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-5010 Vancouver: (604) 278-4211 Calgary: (403) 295-3955 Toronto: (905) 624-8447 Montréal: (514) 633-8684

En México: Panasonic de México, S.A de C.V. México D.F.

Amores 1120, Col. del Valle, 03100 Tel: 54 88 10 00

Service • Assistance • Accessories Dépannage

Call 1-800-338-0552 (In USA) panasonic.com/shavers (In USA) Call 1-800-467-3405 (In Canada, only for shavers) Composer 1-800-467-3405 (Au Canada, pour les rasoirs seulement)

No.1 EN FR ES (U.S.A./CANADA)

• Assistance • Accessoires

Infantry Avenue KM9.5

Printed in China

Imprimé en Chine

Wet/Dry Rechargeable Shaver

Rasoir rechargeable (à sec/avec mousse)

Rasuradora Recargable Agua/Seco

Operating Instructions

Manuel d’utilisation

Instrucciones de operación

Model No. ES8078/ES8077/ES8076/ES8075 N° de modèles ES8078/ES8077/ES8076/ES8075 Modelo No. ES8078/ES8077/ES8076/ES8075

Before operating this unit, please read these instructions completely.

Il est recommandé de lire attentivement ce manuel avant d’utiliser l’appareil.

Antes de operar este producto, lea este instructivo en su totalidad.

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed,

including the following: Read all instructions before using this appliance.

DANGER

1. Do not reach for the appliance if it has fallen into water. Unplug immediately.

2. Do not place or store the power cord where it can fall into a tub or sink. Do not place or drop it into water or other liquid. Before charging the shaver,

3. wipe off any moisture from the shaver and power cord. Always handle with dry hands.

WARNING

Do not use this shaver with damaged shaving blades and/or foil, as facial injury may occur.

Close supervision is necessary when this shaver is used by, on or near children or invalids.

3. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.

4. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged or dropped into water.

To reduce the risk of electric shock:

To reduce the risk of burns, fire, electric shock, or injury to persons:

4. Always charge the shaver in a cool, dry place.

5. Except when charging, always unplug the power cord from the electrical outlet.

6. Unplug this appliance before cleaning. Charger unit is not for immer-

7. sion or for use in shower.

8. Do not use an extension cord with this appliance.

Return the appliance to a service center for examination and repair.

5. Never drop or insert any object into any opening.

6. Keep the cord away from heated surfaces.

7. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.

8. Always attach plug to appliance first, then to outlet. To disconnect, turn off the switch, then remove plug from outlet.

Index Indice

ENGLISH Page 8 FRANÇAIS Page 17 ESPAÑOL Página 28

SAVE THESE INSTRUCTIONS

charge status

recharge

[ES8075]

N O

C D

[ES8078/77/76]

I J

Course completion summary (EE)Course selection indications

Course

On self-cleaning recharger

Courses that can be

changed halfway through

clean

glow

dry charge

Charge

Clean/Dry/Charge

Clean/Dry

Dry/Charge

Dry

˛#

˛$

˛%

˛&

˛'

glow

All courses ˛$˛%˛&˛'

Course %

Course ˛$

Courses ˛$˛%˛'

Courses ˛$˛%˛&

On main unit

Blinks red

Time required (guide)

Approx. 1 hour

Approx. 3 hours

Approx. 2 hours 50 mins.

On self-cleaning recharger

clean dry charge

charge

blinks

(Turns off after 6 secs.)

E The displays on both the self-cleaning recharger and the main unit are the

indications for the completion of each course as shown in the table above.

clean

ry d

e g

r a

h c

s u

t a

t s

select

[ES8078/77/76] [ES8075]

(A) (B) (C) (D)

high

mid low

charge

status

high

charge

status

mid low

recharge

charge

status

recharge

charge

status

high mid low

charge status

5 7

4 5

(a)

(b)

20 21

[ES8078] [ES8077] [ES8076]

high

mid low

charge

status

[ES8075]

recharge

charge status

cleaning recharger securely (see fig. 13, 14, 15).

2. Insert the appliance plug into the socket (see fig. 16-1).

3. Firmly insert the adaptor into the AC outlet (see fig. 16-2).

In some areas, a special plug adaptor may be required.

4. Pull up the arm of the self-cleaning recharger until it clicks (see fig. 17-3).

5. Remove the protective cap and set the shaver firmly onto the selfcleaning recharger until it clicks (see fig. 17-4).

• The Self-cleaning recharger is

set on the (Charge) mode when the shaver is set on.

• Do not push the arm down-

wards.

• Ensure that the outer foil does

not get deformed or damaged when placing the shaver into the self-cleaning recharger.

Note

• Use the self-cleaning recharger in

environments that do not exceed ambient temperatures of 15 to 35 °C and humidity levels of 95%.

• If it is far below or over the appro-

priate temperature, the charging time may extend, or the Self-cleaning recharger may not function.

•

• When charging the shaver for the

first time or when it has not been in

nate for a few minutes after operation. It will eventually illuminate if kept connected.

[for ES8078, ES8077, ES8076] The charge status lamp will glow when the shaver is being charged. The battery capacity monitor will fully illuminate and the charge status lamp will blink after charging is completed (see fig. 4 (A)).

You can fully charge the shaver in 1 hour if the LED display shows “low”. The battery capacity monitor indicates the charge remaining in the battery in 3 levels (high/mid/low). The unit can be used once or twice more after “low” starts to blink. (Differs depending on usage.)

[for ES8075] The charge status lamp will glow when the shaver is being charged. It will blink when charging is completed (see fig. 4 (D)). You can fully charge the shaver in 1 hour if the low battery indicator blinks (see fig. 4 (C)). The unit can be used once or twice more after the low battery indicator starts to blink.

A full charge will supply enough power for approx. 14 shaves (3 minutes per shave for a normal beard).

It will be adjusted automatically to voltages between 100-240V AC.

In particular, low temperature may shorten the life span of the rechargeable battery. In this case, the charge status lamp blinks twice per

10 minutes after charging is completed, the battery capacity monitor will turn off and the charge status lamp will continue to blink (see

use for more than 6 months, the charge status lamp may not illumi-

•

Even when you select the (Clean/ Dry) course or (Dry) course, the shaver might be charged by the self-cleaning recharger.

Before use

This Wet/Dry shaver can be used for wet shaving with shaving lather or for dry shaving. You can use this watertight shaver in the shower and clean it in water. The following is the symbol of Wet shaver. The symbol means that hand-held part may be used in a bath or shower.

Treat yourself to wet lather shaves for at least three weeks and notice the difference. Your Panasonic Wet/ Dry shaver requires a little time to get used to because your skin and beard need about a month to adjust to any new shaving method.

Parts identification 1

(see fig. 1)

A Protective cap B System outer foil C System outer foil release but-

tons

D Foil frame E Inner blades F Foil frame release buttons G Pivot action selector H LED display I Battery capacity monitor

I-a high I-b mid I-c low

J Charge status lamp

K Low battery indicator L On/Off switch M Finger rest N Trimmer O Trimmer handle P Adaptor Q Power cord R Self-cleaning recharger

Parts identification 2

(see fig. 2)

S Detergent cartridge T Water tank U Socket V Arm W Water tank cap X Clean lamp Y Dry lamp Z Charge lamp

Status lamp Select button Feed water line

READ ALL INSTRUCTIONS BEFORE USE.

Charging with self-cleaning recharger

Before each use, ensure that the recharger unit is clean and dry. Thoroughly wipe off any water or moisture on or around the recharger unit.

1. Attach the detergent cartridge and the water tank to the self-

among many other shaving aids (gel, soap, cream, etc.). Do not put a thick layer of shaving foam as it may affect shaver’s performance. If the shaving head is clogged with foam, simply rinse it under running water.

Using the trimmer

(see fig. 9) Slide the trimmer handle up to open the trimmer. Place the trimmer at a right angle to your skin and move it downward to trim sideburns.

Cleaning your shaver

1 Cleaning with the self-cleaning

recharger

Preparing the self-cleaning recharger

Warning – Do not wash or apply water to the adaptor or self-cleaning recharger. Failure to observe this may cause electric shock or result in short circuits.

1. Detach the shaver and the appliance plug from the self-cleaning recharger.

2. Fill the water tank with water.

1) Remove the water tank from

the self-cleaning recharger (see fig. 10-1).

2) Open the water tank cap (see

fig. 10-2).

3) Wash away the old cleaning

liquid inside the water tank and rinse (see fig. 11).

4) Pour tap water up until the

feed water line (see fig. 12).

* Do not pour water over the

water feed line in the tank. This may cause the cleaning liquid to spill.

3. Firmly shut the water tank cap and attach the tank to the selfcleaning recharger (see fig. 13).

4. Peel off the seals from the new detergent cartridge (two seals) (see fig. 14).

• Hold the detergent cartridge horizontally. (The detergent may spill if tilted excessively.)

5. Attach the detergent cartridge to the self-cleaning recharger (see fig. 15).

• Do not use any solution other than the Panasonic Shaver self-cleaning recharger special detergent.

• Be sure to change the detergent cartridge and the cleaning liquid inside the water tank simultaneously. Adding water, or changing just the detergent cartridge or the water, will result in deteriorated cleaning functions.

• When the self-cleaning recharger is operated, the concentrated detergent inside the cartridge will be diluted and the water inside the tank will become a cleaning liquid.

Cleaning your shaver

1. Insert the appliance plug into the self-cleaning recharger socket (see fig. 16-1).

2. Firmly insert the adaptor into the AC outlet (see fig. 16-2).

You can always connect your shaver to the self-cleaning recharger or the adaptor to maintain full battery capacity. This shaver cannot be overcharged. Before travelling, charge it fully for 1 hour if you will not be taking the adaptor with you.

Charging without selfcleaning recharger

Connect the power cord to the shaver, and plug the adaptor to an AC outlet (see fig. 5). The shaver will be adjusted automatically to voltages between 100-240V AC. In some areas, a special plug adaptor may be required.

Using your shaver

Caution – The system outer foil is very thin and can be damaged if handled improperly. Before each use, always check the foil for damage. To avoid personal injury, do not use if the foil or other parts of the shaving head are damaged.

Push the On/Off switch to turn the shaver on.

If you push and hold the On/Off switch for more than 2 seconds, it will activate the turbo mode for “sonic” vibration cleaning. (see “Cleaning your shaver without the self-cleaning recharger”) Shaving with “sonic” vibration may damage your skin. Please turn it off and on again to deactivate the turbo mode.

Do not place fingers on the On/Off switch during use. This may cause the shaver to stop during use or change it to the “sonic” vibration cleaning mode. Place your finger on the finger rest during use.

Hold the shaver at a right angle (90°) to your skin (see fig. 6). Start out shaving by applying gentle pressure to your face. Stretch your skin with your free hand and move the shaver back and forth in the direction of your beard. You may gently increase the amount of pressure as your skin becomes accustomed to this shaver. Applying excessive pressure does not provide a closer shave.

Pivot action selector

(see fig. 7) Use the pivot action selector to choose the shaving mode, “soft” (soft) and “lock” (lock) based on your shaving preference. The pivot action can be changed whether the switch is turned on or off.

System outer foil

(see fig. 8) System outer foil has a slit blade (a) between 2 foils (b). They move up and down independently to follow the contours of your face. The slit blade catches and cuts longer and lying hairs easily.

For wet shaving

Put a thin layer of shaving foam on your face which works as a lubricant. Shaving foam is the most suitable

+ 14 hidden pages