Omron HEM-703CP User Manual

5 (1)
Omron HEM-703CP User Manual

Instruction Manual

Automatic Digital

Blood Pressure Monitor

Model HEM-703CP

HEM-703CP-xxxx 0692581-7 A

Important

Thank you for purchasing our Digital Blood Pressure & Pulse Monitoring Kit.. Please carefully read this instruction manual before use and keep it with your portion of the enclosed warranty card..

PLEASE NOTE:

1.Allow 3 to 5 minutes between blood pressure readings on same arm.. Repeated mea-surement results in inaccurate readings..

2.Keep in mind only a physician can accurately determine safe or unsafe limits of blood pressure.. This instrument should be used by non-professional persons only to determine measurement of blood pressure, not to make any medical judgement.. Remember, blood pressure varies during the day..

3.This unit is a precision instrument − avoid rough handling, direct sunlight, high temperature/humidity and magnetic field.. Fold-ing or bending cuff may result in damage to cuff..

4.Do not inflate cuff above 280 mmHg..

5.Do not take unit apart.. You cannot calibrate unit.. If you have any difficulties or problems with unit, contact our Service Center.. 1-800-634-4350..

CONTENTS

Important .. . . . . . . . . . . . . . . . . . . . . . . . . . 1 Name and Function of Each Part.. . . . . . . . 2 Preparations for Use .. . . . . . . . . . . . . . . . . 3 Instructions for Use .. . . . . . . . . . . . . . . . . . 8 When Error Indication Symbols Appear.. . 10 Specifications.. . . . . . . . . . . . . . . . . . . . . . 11

1

Name and Function of Each Part

Main Unit

Systolic Bood Pressure Display

DiastolicBloodPressureandPulseDisplay

Printing Paper

Air Jack

Paper Cutter

MODE Selector Button

SPHYG/CLOCK Button

SET Button

START Button

 

PRINT / PAPER FEED Button

Cuff

Tab

Air Plug

2 Air Tube

Preparations for Use

1 How to insert the batteries

1.Take off the battery cover at the back of the main unit by sliding it in the direction indicated by the arrow symbol..

Battery Cover

2.Install 4 “AA” size batteries attached so that the + and - polarities on the batteries correctly match the polarities in the battery compartment..

3.Replace the cover..

Replacement

When the “Replace Batteries” symbol ( ) flashes during measurement, please replace the batteries with the new ones..

When the batteries have run down, random numbers may be displayed..

Points to be careful about whan using the batteries

When replacing the batteries please replace all four batteries at once..

Use the same kind of batteries..

Take out weak batteries quickly so as to avoid causing damage to the machine..

Remove the batteries when the unit is not used for extended periods..

3

Preparations for Use

2 How to Set Time and Date

1.When batteries are installed, the display shows PM 12:00..

2.When the MODE button is pressed down, the “month” sign is displayed.. When the SET button is pressed down, the figure for the month increases.. Adjust the “month”..

3.When the MODE button is pressed down after the “month” has been adjusted, the “day” sign is displayed.. Adjust the “day” in the same way as the “month”..

4.In the same manner select the “hour” and “min..” with the MODE button and set each value with the SET button..AM and PM signs are switched in accordance with the “hour” adjsutment..

5..Press the MODE button for the last time and return the screen to normal time (hour, min..) display..

3 Plug in and Turn on

1.Insert the air plug into the air jack on the left side of the main unit correctly..

2.When the SPHYG/CLOCK button is changedtothesphygmomanometermode, all the LCD symbols are momentarily displayed.. This happens because the unit is running a check on the display and this state lasts for approximately one second..

Initial Display

3.Once the LCD symbols vanish, the air release indication symbol ( ) starts flashing.. Please wait until the ( ) symbol goes out..

Air release indication symbol

4.When the preparations necessary before measurement have been completed, the unit emits a series of beeps and finally the “Ready to Measure” symbol ( ♥ ) will be displayed..

“Ready to Measure” Display

4

Loading...
+ 9 hidden pages