Nuvo 250 User Manual

Size:
5.16 Mb
Download

CELLAR nuvo 250/500

ko olspace TM

ASSEMBLY & OPERATION MANUAL

READ BEFORE YOU START

1.LOCATING YOUR WINE CELLAR - Remember, it is not an appliance, it is a piece of furniture

A.Provide 4” minimum clearance for both sides and back, keep the top completely clear. Under no circumstances should the unit be “built-in”in any way.

B.Never locate your wine cellar outdoors or in an area with extremes of temperature and humidity.

Garages, attics, unfinished basements, laundry rooms, breezeways, closets, bedrooms or any unventilated room. In other words these units must be installed in air-conditionedenvironments which do not “trap” the warm air being exhausted.

C.Temperatures in surrounding area must not exceed 80 °F (25 °C) with humidity levels not to exceed 70% R.H. (Relative Humidity). Never set your temperatures below default (57ºF) whenever ambient conditions are warm (above 75ºF) or humid (above 50%R.H.).

D.Outlet power must be a DEDICATED separately fused, grounded, 15 Amp 110 - 120 V line or 7.5 Amp - 240 V line rated for your unit (CHECK BOX OR SERIAL NUMBER LABEL ON UNIT FOR YOUR LINE VOLTAGE REQUIREMENTS).

E.You must monitor your unit DAILY. If unit is in “Alarm”, unplug the unit inmediately. Always check for any water (condensate) leaks.

Vintage Keeper will not be liable or responsible for incidental or consequential damages. (See Warranty).

F.Place unit in a clean area and allow access to the exterior surfaces for periodic vacuuming of the condensor coil. (See troubleshooting for details.)

G.Always remove all bottles before relocating your wine cellar.

2.AREA FOR ASSEMBLING YOUR WINE CELLAR

Choose a clear 12’ by 12’ area with a level floor and carpeting to help reduce scratching of surfaces.

3.TOOLS

*Hex wrench (included)

*Phillips screwdriver

*Carpenter’s level

*Helper or two is strongly recommended

4.TEST THE COOLING UNIT

Plug it in for a few minutes on a table top, to verify that controls and display are functional, and that the unit is producing cool air after a few minutes of operation.

Note that the electronic controller has a one-minutecautionary delay between initialplug-inandstart-upof the compressor.

NOTE: Fill out the WARRANTY REGISTRATION FORM with the serial number located on the LEFT

SIDE of unit.

~2~

HARDWARE KIT

A B C D

Cam Cap

Hex bolt

Coupler screw

Hex wrench

x 26 (x30)*

x 22 (x30)*

x 8

x 1

E F G H

Cam

Cam Pin

Coupler hanger

Hinge

x 24 (x28)*

x 24 (x28)*

x 4

x 4

I J

 

 

 

 

 

 

In Cooling Unit Box

 

Panel Insulation Strip

 

Hex Bolt (Flange)

 

 

x 2

 

*NOTE : Hardware quantities for Model 500 are indicated in parenthesis.

~3~

STEP 1 : PANEL PREPARATION

CAUTION :

1.Watch for sharp staples on boxes.

2.DO NOT STEP ON PANELS

3. The manual will give a recommended

order to open boxes, it saves time and space.

J

Open Boxes VP6 andVP7.

1Install INSULATION STRIP (J)to Back, Top, and Bottom Panels. PUSH

IN FULLY!

2Insert Cam Pins (F) inBACK PANEL’S predrilled holes down to TAB.(May require some force)

J

PANEL EDGE

J

J

! CAUTION : DO NOT BREAK CAM PIN TABS! DO NOT HAMMER!

TAB TAB

BACK PANEL

3

Screw

 

in

both

 

 

screws

(C)

half

 

 

way

in

Coupler

 

 

Hanger (G) to back

 

 

panels and tighten

~4~

 

fully

when

both

screws are in.

C

3

G

STEP 2 : CABINET ASSEMBLY

2

PANEL EDGE

CAM in LOCKED POSITIONMETAL

Use allen key provided or #3 phillips screwdriver.

1Attach TOP and Bottom to Back by CAREFULLY aligning edge holes over Cam Pins and gently push together to avoid damaging cam pins.DO

NOT BANG OR SLAP PANELS TOGETHER!!!

BOTTOM

PANEL

 

2Insert Cam, push all the way inunder panel level (may

require some force) and make sure Arrowpoints to outside edge.

Gently push down to bring panels together before you tighten theCam. Start with cams at each end.

Cam Arrow faces away from outside edge when tightened.

BOTTOM

PANEL

 

 

~5~

METAL

3

Insert Center COUPLER

 

BAR

by guiding edge

 

holes

over bottom

 

Cam Pins. Lightly push

 

out top panel edge to

 

allow Cam Pins to go in

 

Coupler Bar. Insert and

 

tighten Cams.

3

 

COUPLER

 

INSIDE

 

CABINET

BAR

 

STEP 2 : CABINET ASSEMBLY CONTINUED

Open Box VP5 or VP2.

1Insert Cam Pins (F) inBACK PANEL’S predrilled holes down to TAB.(May require some force)

2Attach SIDES to Back/Bottom/Top by CAREFULLY aligning edge holes over Cam Pins and gently push together to avoid damaging cam pins.DO NOT BANG OR SLAP PANELS

TOGETHER!!!

Insert Cam,push all the way in under panel level (may require some force)and make sure Arrowpoints to outside edge., Push Panels together before tightening Cam, use allen key provided or #3 phillips screwdriver. Start with cams at

TOP !!!

F

BOTTOM

PANEL

 

3

2 HOLES FOR MODEL 250

3 HOLES FOR MODEL 500

Insert Cam Cap (A) in allCam Holes.

3

A

~6~

STEP 3 : HINGE,BASE AND LEGS INSTALLATION

 

Open Box VP3.

1

2

Fasten one HINGE (found in

door box) to the SIDEof the

 

cabinet

H

 

2Install four LEGS (H) intoBASES fully in.

3 FastenFRONT

BASE

to

 

the BOTTOMof

the cabinet

 

(FRONT BASEhas to

be set

H

with end tabs away from front

 

edge)

4Fasten BASEwith HEX BOLTS

(B)

H

1

4

BOTTOM

OF

CABINET

 

 

 

B

3

D 1

 

 

5

NOTE: Fasten base with base tab away from the

5

Raise cabinet and check for potential air

front edge, then fasten and adjust the hinge

~7~

leaks at panel joints from inside.

before fully tightening HEX BOLTS (B)

 

STEP 4 : SHELVES

1Install COUPLER SHELVES between theVERTICAL COUPLER and the

BACK PANEL, hook them on the

COUPLER HANGERS (G)

2Install 4 HANGERS STRIPS, hooking them to theCOUPLER SHELVES through square holes. (Watch for orientation, all hooks have to point upwards).

NOTE : Assure that each of them is hooked to all 4 shelves

PRESS

TOP

BOTTOM

3

2

1

COUPLER SHELVES

1

 

G

2

VERTICAL COUPLER

3Open box VP4S or VP4D

Hook SHELVES into hangers starting from the bottom of cabinet, (12 shelves on cooling unit side, 14 on the other) alternating the two sides

HINT :

CENTER SHELVES ON HANGERS

1Snap SHELVES into hangers on one side

2 Push the SHELVES down to snap into opposite side hangers

~8~

STEP 5 : COOLING UNIT INSTALLATION

1 GET HELP BEFORE INSTALLING AND KEEP CHILDREN CLEAR OF CELLAR CONSTRUCTION AREA.

Get helper to help guide unit, keep light cord clear of edge inside cellar and to prevent tipping of cellar. MAKE SURE INSULATION STRIP IS IN CORRECT ORIENTATION. Run light cord throughCut-out.Slide unit into the back

opening by angling unit A to allow light cord to clear and straighten to push inB . Screw allen bolts (I) through bottom fl ange holes. Make sure unit is level!

CHECK

INSULATION

STRIP CELLAR

INSIDE

SHELF

A

KEEP UNIT LEVEL

DO NOT!!!

LEVEL TO

OPENING

SIDE VIEW

B

I

CORD MUST

CLEAR OPENING

(I) x2 Flange bolts in

cooling unit box.

STRAIGHTEN AND PUSH THROUGH

GET HELPER TO LIFT UNIT LEVEL AND PULL FROM INSIDE

DO NOT OVER

TIGHTEN

NOTE: If unit is operated according to specifi cations overfl ows will not occur. Excess condensation is only caused by extreme conditions. Unit will shut off at 72 °F and will restart when temperature drops or unit is repluged. (In this case insert 3/8” O.D. hose to drain hole, cut to appropriate length.)

Optional (not required) except as emergency

drain. Container

~9~

STEP 6 : LIGHT AND LIGHT COVER INSTALLATION

1 Remove plasticCAP at right end for2 Plug cord toLIGHTS 1 and 2 onlyLIGHT 1 ,DO NOT remove CAP

from LIGHT 2 .

CAP

LIGHT 1

Cord behind

LIGHT 2

 

3 Insert LIGHTto LIGHT COVER

4

Insert LIGHT COVER to holes pre

 

 

 

 

 

 

 

 

 

 

 

drilled on front edge of TOP panel.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

~10~