Navman 5500I, 5500, 5100I, 5100 User Manual

4 (3)
Navman 5500I, 5500, 5100I, 5100 User Manual

w w w . n a v m a n . c o m

TRACKER 5500, 5500i

5100 and 5100i

C H A R T P L O T T E R S

Installation and

Operation Manual

English .............

2

Español ..........

41

Português ......

79

TRACKER 5100i

TRACKER 5500

TRACKER 5500i

TRACKER 5100

NAVMAN

FCC Statement

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a normal installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an output on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced technician for help.

A shielded cable must be used when connecting a peripheral to the serial ports.

2

NAVMAN TRACKER 5100/5100i/5500/5500i Installation and Operation Manual

Contents

 

1 Introduction .....................................................................................................

6

1-1 Care ............................................................................................................................

6

1-2 Plug-in cards ...............................................................................................................

6

1-3 Removing and replacing the display unit ......................................................................

7

2 Basic operation ...............................................................................................

8

2-1 Turning on and off / auto power ...................................................................................

9

2-2 The main displays ........................................................................................................

9

2-3 Backlight and display contrast ...................................................................................

10

2-4 Man overboard (MOB) ...............................................................................................

10

2-5 Alarms .......................................................................................................................

10

2-6 Simulate mode ...........................................................................................................

10

2-7 Navigating .................................................................................................................

11

3 Chart ...............................................................................................................

12

3-1 Chart display .............................................................................................................

12

3-1-1 Chart modes .....................................................................................................

12

3-1-2 Latitude and longitude .......................................................................................

13

3-1-3 Chart scale ........................................................................................................

13

3-1-4 The compass ....................................................................................................

13

3-1-5 Chart symbols ...................................................................................................

13

3-1-6 Chart information ...............................................................................................

13

3-1-7 Find nearby services .........................................................................................

13

3-1-8 Change the data display and compass display ..................................................

13

3-2 Distance and bearing calculator .................................................................................

14

3-3 Goto ..........................................................................................................................

14

3-4 Projected course .......................................................................................................

15

3-5 Tracks and tracking ...................................................................................................

15

4 Fuel display ...................................................................................................

16

5 Data display ...................................................................................................

16

6 Highway display ............................................................................................

17

7 Satellites ........................................................................................................

17

7-1 Satellite display ..........................................................................................................

18

8 Tides display ..................................................................................................

19

9 Waypoints ......................................................................................................

20

9-1 Waypoints display ......................................................................................................

20

9-2 Managing waypoints ..................................................................................................

20

9-2-1 Creating a new waypoint ....................................................................................

20

9-2-2 Moving a waypoint .............................................................................................

21

9-2-3 Editing a waypoint .............................................................................................

21

9-2-4 Displaying a waypoint on the chart .....................................................................

21

9-2-5 Deleting a waypoint ...........................................................................................

21

9-2-6 Deleting all waypoints ........................................................................................

21

9-2-7 Changing a waypoint’s data ...............................................................................

21

NAVMAN TRACKER 5100/5100i/5500/5500i Installation and Operation Manual

3

10 Routes ..........................................................................................................

22

10-1 Routes display .........................................................................................................

22

10-2 Managing routes ......................................................................................................

22

10-2-1 Creating a new route .......................................................................................

22

10-2-2 Editing a route .................................................................................................

23

10-2-3 Displaying a route on the chart ........................................................................

23

10-2-4 Deleting a route ...............................................................................................

23

10-2-5 Deleting all routes ............................................................................................

23

10-3 Navigating a route ....................................................................................................

23

10-3-1 Starting a route ................................................................................................

23

10-3-2 Skipping a waypoint in a route .........................................................................

23

10-3-3 Cancelling a route ...........................................................................................

23

11 User card display .........................................................................................

24

12 About display ...............................................................................................

25

13 Setup menu ..................................................................................................

25

13-1 System setup ...........................................................................................................

25

13-2 Chart setup ..............................................................................................................

27

13-3 DGPS setup ............................................................................................................

28

13-4 Fuel Setup ...............................................................................................................

28

13-5 Track setup .............................................................................................................

29

13-6 Alarms setup ...........................................................................................................

29

13-7 Units setup ..............................................................................................................

30

13-8 Comms setup ..........................................................................................................

30

13-9 Time setup ...............................................................................................................

30

13-10 Simulate setup .......................................................................................................

31

14 Systems of several instruments ................................................................

31

15 Installation ...................................................................................................

32

15-1 What comes with the TRACKER .............................................................................

32

15-2 Options and accessories .........................................................................................

32

15-3 Installation ...............................................................................................................

33

Appendix A - Specifications ............................................................................

36

Appendix B - Troubleshooting ........................................................................

38

Appendix C - Glossary and navigation data ..................................................

39

Appendix D - How to contact us ....................................................................

119

4

NAVMAN TRACKER 5100/5100i/5500/5500i Installation and Operation Manual

Important

It is the owner's sole responsibility to install and use the instrument in a manner that will not cause accidents, personal injury or property damage. The user of this product is solely responsible for observing safe boating practices.

Global Positioning System: The Global Positioning System (GPS) is operated by the US government which is solely responsible for its operation, accuracy and maintenance. The GPS system is subject to changes which could affect the accuracy and performance of all GPS equipment anywhere in the world including the TRACKER. Whilst the NAVMAN TRACKER is a precision navigation instrument, it can be misused or misinterpreted, which can result in its use being unsafe. To reduce the risk of misusing or misinterpreting the TRACKER, the user must read and understand all aspects of this Installation and Operation manual. We also suggest that the user practice all operations using the built in simulator before using the TRACKER at sea.

Electronic Chart: The electronic chart used by the TRACKER is an aid to navigation and is designed to supplement the use of official government charts not replace them. Only official government charts supplemented by notices to mariners contain the information required for safe and prudent navigation. Always supplement the information provided by the TRACKER with other plotting sources such as observations, depth soundings, radar and hand compass bearings. Should the information not agree then the discrepancy must be resolved before proceeding any further.

Fuel Computer: Fuel economy can alter drastically depending on the boat loading and sea conditions. The fuel computer should not be the sole source of information concerning available fuel onboard and the electronic information should be supplemented by visual or other checks of the fuel load. This is necessary due to possible operator induced errors such as forgetting to reset the fuel used when filling the tank, running the engine with the fuel computer not switched on or other operator controlled actions that may render the device inaccurate.Always ensure that adequate fuel is carried onboard for the intended trip plus a reserve to allow for unforeseen circumstances.

NAVMAN NZ LIMITED DISCLAIMS ALL LIABILITY FOR ANY USE OF THIS PRODUCT IN A WAY THAT MAY CAUSE ACCIDENTS, DAMAGE OR THAT MAY VIOLATE THE LAW.

Governing Language: This statement, any instruction manuals, user guides and other information relating to the product (Documentation) may be translated to, or has been translated from, another language (Translation). In the event of any conflict between any Translation of the Documentation, the English language version of the Documentation will be the official version of the Documentation.

This manual represents the TRACKER as at the time of printing. Navman NZ Limited reserves the right to make changes to specifications without notice.

Copyright © 2002 Navman NZ Limited, New Zealand, all rights reserved. NAVMAN is a registered trademark of Navman NZ Limited.

NAVMAN TRACKER 5100/5100i/5500/5500i Installation and Operation Manual

5

1 Introduction

TRACKER chartplotters

NAVMAN’s TRACKER chartplotters are compact, ruggedly built, highly integrated navigation instruments. They have been designed to be easy to use. Complex navigation functions can be performed with a few key presses, taking the hard work out of navigation.

This manual covers these NAVMAN chartplotters:

TRACKER 5500

Colour display, external GPS antenna.

TRACKER 5500i

Colour display, internal GPS antenna.

TRACKER 5100

Greyscale display, external GPS antenna.

TRACKER 5100i

Greyscale display, internal GPS antenna. The TRACKER has a built-in chart of the world, suitable for route planning and general interest. To see chart details for a region, plug in a C-MAP™ chart card (an electronic chart).

The TRACKER receives information from the GPS system and displays the boat’s position and speed.

The TRACKER can navigate to a point or can navigate along a route. When the boat is navigating to one of these points, the TRACKER displays course information for the helmsman to follow.

The TRACKER can control an autopilot and can display depth information from a depth sounder. With an optional fuel kit, the TRACKER becomes a sophisticated yet easy to use fuel computer. Navigation data can be saved to a plug-in user card so that it can be easily transferred to another NAVMAN chartplotter.

The TRACKER is part of the NAVMAN family of instruments, which includes instruments for speed, depth, wind and repeaters. These instruments can be connected together to form an integrated data system (see section 14).

For maximum benefit, please read this manual carefully before installing and using the unit. Special terms are explained in appendix C.

1-1 Care

Cleaning and maintenance

Caution should be used when cleaning the TRACKER, and especially the screen of the TRACKER. Only use a clean sponge or chamois soaked in fresh water and mild detergent. Never use a dry cloth as this may drag dried salt crystals across the screen resulting in scratching. Do not use any form of abrasive cleaner, solvent, petrol or other chemical cleaner.

Push the dust cover over the display when the TRACKER is turned off.

Plug-in cards

Handle plug-in cards carefully. Keep them in their protective cases when not plugged into the TRACKER.

If a card gets dirty or wet, clean it with a damp cloth or mild detergent.

Keep the card holder in place in the display unit at all times to prevent moisture from entering the card compartment.

1-2 Plug-in cards

The TRACKER can use two kinds of plug-in cards:

C-MAP™ chart card have chart details required for navigating in a particular region. When a chart card is plugged in, the extra details automatically appear on the TRACKER’s chart display.

C-MAP™ user cards are used to store navigation data. Each user card expands the TRACKER’s memory and allows the data to be transferred to another TRACKER easily (see section 11).

When a card is inserted or removed it does not matter if the TRACKER is turned on or off.

6

NAVMAN TRACKER 5100/5100i/5500/5500i Installation and Operation Manual

Changing the plug-in card

Gold contacts under here

 

1

2

3

4

 

 

Card

 

 

 

Holder

 

Pull card holder out of TRACKER.

Pull any card out of holder. Put card in case.

Push new card into holder. Ensure the gold contacts are on the outer edge and underneath (see above). Keep the card’s case.

Push card holder fully into TRACKER.

Warning: Keep the holder in place in the TRACKER at all times to prevent moisture from entering card compartment.

1-3 Removing and replacing the display unit

If the display unit is bracket mounted then the display unit can easily be removed and replaced for security or protection.

Removing the display unit:

1Turn the TRACKER off by holding until the display turns off.

2Push the dust cover over the display unit.

3Hold the display unit with one hand. Loosen the knob on the mounting bracket and carefully lift the unit off the mounting bracket.

4The display unit has some cables plugged into the back.

Unplug each black plug by turning the locking collar a quarter turn anticlockwise and pulling the plug out.

If there is a gold plug, unscrew the locking collar anticlockwise and pull the plug out.

5Push the attached dust covers over the exposed ends of the plugs to protect them.

6Store the display unit in a safe place, such as the optional NAVMAN carry bag.

Replacing the display unit

1Remove the dust covers from the plugs. Plug the black plugs into their sockets on the back of the display unit:

Match the colour on the end of the plug to the colour of the nut on the socket.

Hold the plug against the socket and rotate the plug until it slides into the socket.

Lock the plug in place by pushing the locking collar towards the socket and turning it a quarter turn clockwise.

Nothing will be damaged if a cable is plugged into the wrong socket by mistake.

2 If the unit has a gold plug:

Plug it into its socket on the back of the display unit.

Hand tighten the locking collar clockwise - do not overtighten.

3Hold the display unit in place on the mounting bracket shaft, with the rubber washer clamped between the bracket and the display unit.

4Adjust the tilt and rotation of the display for best viewing and hand tighten the knob on the mounting bracket. Remove the dust cover.

NAVMAN TRACKER 5100/5100i/5500/5500i Installation and Operation Manual

7

2 Basic operation

Overview of the keys

ESC Go back to an earlier menu or display. Any changes are ignored.

DISP Show a menu of the main TRACKER displays. To go to a display, select it from the menu (see section 2-2).

,, , Cursor keys, to move the cursor or the selection highlight.

MENU Show a menu of the options for the current display. Press MENU again to display the setup menu (see section 13).

ENT Start an action or accept a change.

Zoom in and display a smaller area of the chart in more detail.

Zoom out and display a bigger area in less detail.

Create an instant waypoint at the boat position (see section 9-2-1).

Man overboard (MOB, see section 2-4).

Turn TRACKER on and off (see section 2-1); adjust the display (see section 2-3).

Keys

In this manual:

Press means to push the key for less than a second.

Hold means to hold the key down.

The internal beeper beeps when a key is pressed (to disable or enable the beep, see section 13-1).

To select an item in a menu

The TRACKER is operated by selecting items from menus shown on the display.

1Press or to move the highlight to the item.

2Press ENT or to select the item.

Change a number or word

To change a number or word on the display:

1Press or to move the highlight to the digit or letter to change.

Press or to change the digit or letter.

2Repeat the above step to change any other digits or letters.

3Press ENT to accept the change.

8

NAVMAN TRACKER 5100/5100i/5500/5500i Installation and Operation Manual

2-1 Turning on and off / auto power

Auto power

If the TRACKER is wired for auto power (see section 15-3), then the TRACKER automatically turns on and off with the boat power, and can not be turned on or off manually.

Turning on manually

If the TRACKER is not wired for auto power, turn the unit on by pressing .

Startup

After the TRACKER has been turned on:

1The unit displays a title display for a few seconds, then beeps again and displays a navigation warning.

2If necessary, adjust the display to be easy to read (see section 2-3).

Read the warning and press ENT.

3The satellite display is shown.

Either wait for the GPS receiver to start up and the status to change from ‘acquiring’ to ‘GPS fix’ (see section 7).

Or press ESC.

4 The TRACKER chart is displayed (see section 3).

Turning off manually

If the TRACKER is not wired for auto power, turn the unit off by holding down until the display turns off.

2-2 The main displays

After you have turned the TRACKER on, it shows the satellite display until the GPS receiver gets a GPS fix, then displays the Chart. The Chart is the display that you will normally use for navigation.

To use one of the other main displays, press DISP for the display menu and select a display to use.

To return to the chart display, press ESC.

Display menu

The main displays

See:

 

Chart

Chart (navigation)

Section 3

Fuel

Fuel (fuel computer)

Section 4

Data

Data (numeric data)

Section 5

Highway

Highway (boat path)

Section 6

Satellite

Satellite (GPS data)

Section 7

Tides

Tides (tide chart)

Section 8

Waypoints

Waypoints

 

Section 9

Routes

Routes

 

Section 10

User C-card

User card

Section 11

About

About

 

Section 12

Press DISP for display menu

To select a display:

ipress or to highlight the display

iipress ENT to go to the display

Press ESC to return to chart display

NAVMAN TRACKER 5100/5100i/5500/5500i Installation and Operation Manual

9

2-3 Backlight and display contrast

1Press briefly to show the display controls.

2The display and keys are backlit, with sixteen brightness levels.

To change the backlight, press (dimmer) or

(brighter)

3To change the display contrast (TRACKER 5100 or 5100i):

iPress to choose Contrast.

iiPress or to adjust the contrast.

4Press ENT to accept the new values.

2-4 Man overboard (MOB)

The MOB feature saves the boat’s position and then navigates back to this point. To do this:

1Press .

The TRACKER beeps four times and stores the boat’s position as a waypoint called MOB.

2The TRACKER changes to the chart display, with the MOB waypoint at the centre of the chart.

The chart zooms in for accurate navigation. If the chart can not show the required small scale, the TRACKER changes to plotter mode (a white display with crosshatching, and no chart details, see section 13-2).

3If the autopilot output is off (see section 13-8) the TRACKER immediately starts navigating back to the MOB waypoint.

If the autopilot output is on, the TRACKER asks if the autopilot is active. Select:

No: The TRACKER immediately starts navigating back to the MOB waypoint.

Yes: The TRACKER asks if the boat is to go to the MOB waypoint. Select:

Yes: to immediately start navigating to the MOB waypoint.

Warning: This might result in a sudden and dangerous turn.

No: to allow time to disengage the autopilot; then use Goto to navigate back to the MOB waypoint

(see section 3-3) .

To cancel MOB or set another MOB.

1Press again to display a menu.

2Select an option from the menu.

Tip: The MOB waypoint remains on the chart after the MOB has been cancelled. To delete the MOB waypoint, (see section 9-2-5).

2-5 Alarms

When the TRACKER detects an alarm condition, it displays a warning message on the display, the internal beeper sounds and any external beepers or lights operate.

Press ESC to clear the alarm. The alarm will sound again if the alarm condition occurs again.

2-6 Simulate mode

The TRACKER has five user settable alarms: arrival radius, anchor, XTE, danger and low fuel (see section 13-6).

In addition, the TRACKER has a fixed alarm for loss of GPS/DGPS fix.

Simulate mode allows a user to become familiar with the TRACKER off the water. In Simulate mode, the data from the GPS receiver and other sensors is ignored and the TRACKER generates this data internally to simulate the movement of the boat. Otherwise, the TRACKER functions normally.

To see if the TRACKER is in Simulate mode, press DISP and select Satellite. If it is in Simulate mode, then it shows Simulate at the top left of the display.

To start and stop Simulate mode, (see section 13-10).

Warning: Never have Simulate mode on when the TRACKER is navigating on the water.

10

NAVMAN TRACKER 5100/5100i/5500/5500i Installation and Operation Manual

2-7 Navigating

The TRACKER has two ways of navigating, going straight to a point or following a route.

Enter waypoints at points of interest before starting to navigate (see section 9-2-1).

Tip: create a waypoint at the start of the trip to navigate back to.

Goto: Going straight to a point

The TRACKER can navigate straight to a waypoint or to any arbitrary point:

1In the chart display, move the cursor to the destination point to navigate to (see section 3-1-1).

2Start navigating using the Goto function from the chart menu (see section 3-3).

The chart, data and highway displays show navigation data. The chart shows:

The boat position .

The destination point marked with a circle.

The boat’s plotted course to the destination.

Two CDI lines, parallel to the boat’s plotted course (see appendix C, CDI).

If the TRACKER is connected to an autopilot, the TRACKER will send data to the autopilot to steer the boat to the destination.

If the XTE alarm is enabled, an alarm will sound if the boat deviates too much from its intended course (to set the XTE alarm, see section 13-6).

3If the arrival radius alarm is enabled, then, when the boat comes within the arrival radius of the destination, an alarm will sound to show that the boat has reached the destination (to set the arrival radius alarm, see section 13-6).

4To stop the Goto, (see section 3-3).

Following a route

A route is a list of waypoints that the boat can follow (see section 10).

1To create waypoints before creating the route, use the waypoints display (see section 9-2-1).

2To create a route, go to the chart or routes display (see section 10-2-1).

3To start the route, see section (10-3-1).

The chart, data and highway displays show navigation data. The chart shows:

The boat position .

The waypoint at the end of the current leg marked with a circle.

The boat’s plotted course along the leg.

Two CDI lines, parallel to the boat’s plotted course (see appendix C, CDI).

If the TRACKER is connected to an autopilot, the TRACKER will send data to the autopilot to steer the boat to the destination.

If the XTE alarm is enabled, an alarm will sound if the boat deviates too much from its intended course (see section 13-6).

If the arrival radius alarm is enabled, then, when the boat comes within the arrival radius of the waypoint at the end of the current leg, an alarm will sound (to set the arrival radius alarm, see section 13-6).

4The TRACKER stops navigating to the waypoint at the end of the current leg and starts the next leg of the route:

a When the boat comes within 0.025 nm of the waypoint.

b Or when the boat passes the waypoint.

c Or if the waypoint is skipped (see section 10-3-2).

5When the boat has reached the final waypoint, or to stop the boat following the route at any time, cancel the route (see section 10-3-3).

NAVMAN TRACKER 5100/5100i/5500/5500i Installation and Operation Manual

11

3 Chart

The chart display is the most important of the TRACKER’s displays, showing the chart, the boat’s position and course, and navigation data.

3-1 Chart display

A typical chart display shows:

Data display. To turn the data off or on or to change what data is displayed, see section 3-1-8.

The chart. To change the types of information displayed, (see section 13-2).

Boat position (see section 3-1-1)

Boat track (see section 3-5)

Boat course and CDI lines (see appendix C, CDI)

Boat is going to the waypoint called FISH06.

Distance and bearing of cursor from boat.

Chart is in cursor mode, press ESC to return to centre on boat mode (see section 3-1-1)

Compass display (see section 3-1-4).

To turn the compass off or on, see section 3-1-8.

Typical waypoint (see section 9).

The cursor

(see section 3-1-1).

Sea

Land

3-1-1 Chart modes

The Chart has two modes, centre on boat mode and cursor mode. These are explained below.

Centre on boat mode

To switch to centre on boat mode in the chart display, press ESC. The boat is at the centre of the chart. As the boat moves through the water, the chart automatically scrolls to keep the boat in the centre of the chart. The cursor (see below) is turned off.

Cursor mode

The keys, , and are called cursor keys. To switch to cursor mode in the chart display, hold down a cursor key. The cursor appears and moves away from the boat:

Press the key which points in the direction that the cursor will move, for example press to move the cursor down.

Press midway between two of the cursor keys to make the cursor move diagonally.

Hold a cursor key down to make the cursor move continuously across the display.

In Cursor mode:

The distance (+RNG) and bearing (+BRG) of the cursor from the boat are displayed at the bottom, left corner of the display.

The chart does not scroll as the boat moves.

If the cursor reaches the edge of the display, the chart will scroll.

For example, hold down to move the cursor to the right side of the display and the chart will scroll to the left.

12

NAVMAN TRACKER 5100/5100i/5500/5500i Installation and Operation Manual

3-1-2 Latitude and longitude

Latitude and longitude can be displayed at the top of the chart. Normally the position is the boat’s position, and the latitude has a boat symbol to show this:

36° 29.637'S

Latitude

175° 09.165'E

Longitude

Degrees Minutes, to 3 decimal places (about 2 m (6 ft) resolution)

If the cursor has been moved in the last ten seconds, then the position is the cursor’s position, and the latitude has a cursor symbol to show this:

+36° 29.684'S 175° 09.201'E

Warning: When reading the boat position, make sure the position is not the cursor position.

3-1-3 Chart scale

Press to zoom in and display a smaller area of the chart in more detail. Press to zoom out and display a bigger area in less detail.

The chart scale can be displayed (e.g. scale = 8 nm, see below). The scale is the vertical distance across the currently visible chart area. For example if the scale is 8 nm then a portion of chart eight nautical miles high is currently displayed.

3-1-4 The compass

A compass can be displayed at the top of the chart (see section 3-1-8).

When the boat is navigating to a point, the compass shows the bearing to the destination (BRG) in the middle and the boat’s course over ground (COG), for example here BRG is 4° and COG is 12°:

BRG (red)

COG

Otherwise the compass shows the boat’s COG in the middle, for example here COG is 12°:

3-1-5 Chart symbols

COG

The chart will show symbols, such as waypoints and chart symbols. When the cursor is placed over a symbol for at least two seconds, a data window appears at the bottom left of the display with information about the symbol.

3-1-6 Chart information

To see stored data about a point on the chart (for example, a chart symbol):

1Move the cursor to that point on the chart.

2Press MENU and select Chart info.

3A menu of objects is displayed:

iSelect an object to display.

iiPress ESC to return to the menu. Select other objects.

iiiFinally, press ESC to return to the chart.

3-1-7 Find nearby services

To find and display nearby services:

1To see services near the boat’s position, press ESC to switch to centre on boat mode. To see services near a different point, move the cursor to that point on the chart.

2Press MENU and select Find.

3Select the type of service. There are three types of service:

Ports

A list of ports is displayed. Select the port to display.

To search for a port:

iPress MENU and select Find.

iiEnter some or all of the letters of the port name. Press ENT.

Port services

iSelect the type of service to find.

iiA list of places with this service are

displayed. Select the place to display.

Tide stations

A list of tide stations is displayed. Select the station to display. The chart redraws with the tide station centred. To now display a tide chart (see section 8) for the station:

iPress MENU and select Chart info.

iiSelect Tide height.

3-1-8 Change the data display and compass display

Numeric data and a compass can be displayed at the top of the chart display. To change these:

1Press MENU and select Data header.

2To turn the data display off or on:

iSelect Data.

iiSelect Off or On.

3To choose the size of the numbers:

iSelect Size.

iiSelect:

Small: displays three fields per line and up to four lines.

Large: displays two fields per line and up to four lines.

NAVMAN TRACKER 5100/5100i/5500/5500i Installation and Operation Manual

13

Loading...
+ 29 hidden pages