Multiquip TLG-12SPX4 User Manual

0 (0)
PARTS AND OPERATION MANUAL
OPERATION AND PARTS MANUAL
WHISPERWATT
TM
SERIES
60 Hz GENERATOR
Revision #1 (12/17/09)
THIS MANUAL MUST ACCOMPANY
THE EQUIPMENT AT ALL TIMES.
Diesel engine exhaust and some of
PAGE 2 — TLG-12SPX4— OPERATION AND PARTS MANUAL — REV. #1 (12/17/09)
NOTE PAGE
1
TLG-12SPX4— OPERATION AND PARTS MANUAL — REV. #1 (12/17/09) — PAGE 3
TABLE OF CONTENTS
MQ POWER TLG-12SPX4MQ POWER TLG-12SPX4
MQ POWER TLG-12SPX4
MQ POWER TLG-12SPX4MQ POWER TLG-12SPX4
TMTM
TM
WHISPERWHISPER
WHISPER
WHISPERWHISPER
California Proposition 65 Warning ..................................... 2
Table Of Contents ............................................................. 4
Parts Ordering Procedures ............................................... 5
Specifications ................................................................... 6
Dimensions (Top, Side, Front) .......................................... 7
Safety Message Alert Symbols .................................... 8-9
Rules for Safe Operation ........................................... 10-14
Installation ................................................................. 15-16
General Information ........................................................ 17
Major Components ......................................................... 18
Generator Control Panel ............................................ 19-20
Output Terminal Panel Familiarization ........................ 21-23
Load Application/Max Amperage .................................... 24
Setup ......................................................................... 25-28
Generator Start-up Procedure ................................... 29-30
Generator Shut-Down Procedure .................................... 31
Maintenance (Engine) ................................................ 32-33
Maintenance (Trailer) ................................................. 34-36
Generator Wiring Diagram ............................................... 37
Engine Wiring Diagram ................................................... 38
Troubleshooting (Engine) ........................................... 39-40
Troubleshooting (Generator) ............................................ 41
Explanation of Code in Remarks Column ....................... 42
Suggested Spare Parts .................................................. 43
WW
W
WW
AA
A
AA
TTTT
TT
TTTT
TMTM
GENERATORGENERATOR
GENERATOR
GENERATORGENERATOR
COMPONENT DRACOMPONENT DRA
COMPONENT DRA
COMPONENT DRACOMPONENT DRA
Generator Assembly .................................................. 44-45
Control Panel Assembly ............................................ 46-49
Engine and Radiator Assembly ................................. 50-53
Battery Assembly ...................................................... 54-55
Muffler Assembly ...................................................... 56-57
Fuel Tank Assembly .................................................. 58-59
Enclosure Assembly ................................................. 60-63
Rubber Seals Assembly ............................................ 64-65
Nameplate and Decals .............................................. 66-69
Terms and Condition of Sale — Parts ............................ 70
Specifications are subject to
NOTE
change without notice.
WINGSWINGS
WINGS
WINGSWINGS
PAGE 4 — TLG-12SPX4— OPERATION AND PARTS MANUAL — REV. #1 (12/17/09)
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
January 1
Effective:
st
, 2006
Best Deal!
Order via Internet (Dealers Only):
Order parts on-line using Multiquip’s SmartEquip website!
N View Parts Diagrams
N Order Parts N Print Specification Information
Goto www.multiquip.com and click on
Order Par ts
Order via Fax (Dealers Only):
All customers are welcome to order parts via Fax. Domestic (US) Customers dial: 1-800-6-PARTS-7 (800-672-7877)
Non-Dealer Customers: Contact your local Multiquip Dealer for parts or call 800-427-1244 for help in locating a dealer near you.
to log in and save!
Order via Phone:
If you have an MQ Account, to obtain a Username and Password, E-mail us at: parts@multiquip.
com.
To obtain an MQ Account, contact your District Sales Manager for more information.
Use the internet and qualify for a 5% Discount on Standard orders for all orders which include complete part numbers.*
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 2% Discount on Standard orders for all orders which include complete part numbers.*
Note: Discounts Are Subject To Change
Domestic (US) Dealers Call:
1-800-427-1244
International Customers should contact their local Multiquip Representatives for Parts Ordering information.
R Dealer Account Number R Dealer Name and Address R Shipping Address (if different than billing address) R Return Fax Number R Applicable Model Number R Quantity, Part Number and Description of Each Part
www.mqpower.com
TLG-12SPX4— OPERATION AND PARTS MANUAL — REV. #1 (12/17/09) — PAGE 5
When ordering parts, please supply:
R Specify Preferred Method of Shipment: UPS/Fed Ex DHL
N Priority One Tr uck  N Ground N Next Day N Second/Third Day
NOTICE
All orders are treated as Standard Orders and will
ship the same day if received prior to 3PM PST.
WE ACCEPT ALL MAJOR CREDIT CARDS!
1
TLG-12SPX4 — SPECIFICATIONS
ledoM4XPS21-GLT
snoitacificepSrotareneG.1elbaT
epyT
esahP
tuptuOybdnatS
t
uptuOemirP
egatloV
ycneuqerF
deepS
rotcaFrewoP
esahPelgniS
WK31
WK21
021/V042
zH06
mpr0063
0.1
rotareneGsuonorhcnySepytnoitcetorP,dleifgnivloveR
snoitacificepSenignE.2elbaT
ledoM
epyT
srednilyCfo.oN
ekortSxeroB
209DATOBUK
epytrebmahcnoitsubmoclriws,delooc-retaw,elcyC4
srednilyc3
)
mm47xmm27(.ni9.2x.ni38.2
tuptuOdetaR
tnemecalpsiD
gnitratS
CtnalooC
yticapa
yticapaCliOebuL
yticapaCknaTleuF
tarh/)sretil2.5(.lag4.1 daollluf tarh/)sretil4.4(.lag1.1 daol4/3
usnoCleuF
noitpm
tarh/)sretil8.3(.lag1 daolflah ta
yrettaB
leuF
mpr0063/PH5.02
)cc898(.ni.uc8.45
cirtcelE
)sretil7.2(.lag17.0
)sretil6.3(.lag59.0
)sretil15(.lag5.31
rh/)sretil1.3(.lag8.o daol4/1
)A525:72(HA56V21
leuFleseiD2#
PAGE 6 — TLG-12SPX4— OPERATION AND PARTS MANUAL — REV. #1 (12/17/09)
Figure 1. Dimensions
SNOISNEMID.3ELBAT
retteLecnerefeR).mm(.tfnoisnemiD
A).mm095(.ni32.32
B).mm544(.ni25.71
C).mm005(.ni96,91
D).mm004,1(.ni21.55
E).mm
058(.ni64.33
F).mm096(.ni71,72
TLG-12SPX4 — DIMENSIONS (TOP, SIDE AND FRONT)
TLG-12SPX4— OPERATION AND PARTS MANUAL — REV. #1 (12/17/09) — PAGE 7
1
TLG-12SPX4 — SAFETY MESSAGE ALERT SYMBOLS
FOR YOUR SAFETY AND THE SAFETY OF OTHERS!
Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others.
This Owner's Manual has been
NOTE
ensure that the operating individual has read and understands all instructions in this manual.
SAFETY MESSAGE ALERT SYMBOLS
The three (3) Safety Messages shown below will inform you about potential hazards that could injure you or others. The Safety Messages specifically address the level of exposure to the operator, and are preceded by one of three words:
DANGER, WARNING, or CAUTION.
DANGER
You WILL be KILLED or SERIOUSLY injured if you do not follow directions.
developed to provide complete instructions for the safe and efficient operation of the MQ Power
Before using this generator,
Generator.
HAZARD SYMBOLS
Potential hazards associated with the operation of this equipment will be referenced with " appear throughout this manual, and will be referenced in conjunction with Safety "
WARNING - LETHAL EXHAUST GASES
equipment in a confined area or enclosed structure that does not provide ample free flow air.
WARNING - EXPLOSIVE FUEL
DO NOT overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or sparks from the ignition system. Store fuel in approved containers, in well-ventilated areas and away from sparks and flames.
NEVER use fuel as a cleaning agent.
Hazard Symbols
Message Alert Symbols
Gasoline engine exhaust gases contain poisonous carbon monoxide. This gas is colorless and odorless, and can cause
DEATH
if inhaled. NEVER operate this
Diesel fuel
its vapors can cause an explosion if ignited. DO NOT start the engine near spilled fuel or combustible fluids. DO NOT fill the fuel tank while the engine is running or hot.
is extremely flammable, and
" which
".
WARNING
You COULD be KILLED or SERIOUSLY injured if you do not follow directions.
CAUTION
You CAN be injured if you do not follow directions
PAGE 8 — TLG-12SPX4— OPERATION AND PARTS MANUAL — REV. #1 (12/17/09)
WARNING - BURN HAZARDS
Engine components can generate extreme heat. To prevent burns, DO NOT touch these areas while the engine is running or immediately after operations. NEVER operate the engine with heat shields or heat guards removed.
DANGER - ELECTROCUTION HAZARDS
During operation of this generator, there exists the possibility of
electrical shock or burn, severe bodily harm
electrocution,
which can cause
or even
DEATH!
TLG-12SPX4 — SAFETY MESSAGE ALERT SYMBOLS
WARNING - ROTATING PARTS
NEVER operate equipment with covers,
or guards removed. Keep
hair
and clothing away from all moving
parts to prevent injury.
CAUTION - ACCIDENTAL STARTING
ALWAYS place the engine ON/OFF
switch (MPEC) in the OFF/RESET position when the generator is not in use.
CAUTION - OVER-SPEED CONDITIONS
NEVER tamper with the factory settings
of the engine governor or settings. Personal injury and damage to the engine or equipment can result if operating in speed ranges above maximum allowable.
fingers, hands
CAUTION - RESPIRATORY HAZARDS
,
CAUTION - SIGHT AND HEARING HAZARDS
CAUTION - EQUIPMENT DAMAGE MESSAGES
Other important messages are provided throughout this manual to help prevent damage to your generator, other property, or the surrounding environment.
ALWAYS wear approved protection.
ALWAYS wear approved
hearing
protection.
respiratory
eye
and
NOTE
Wet-Stacking is a common problem with diesel engines which are operated for extended periods with light or no load applied. When a diesel engine operates without
This generator, other property, or the surrounding environment could be damaged if you do not follow instructions.
sufficient load (less than 40% of the rated output) it will not operate at its optimum temperature. This will allow unburned fuel to accumulate in the exhaust system, which can foul the fuel injectors, engine valves and exhaust system, including turbocharges, and reduce the operating performance. In order for a diesel engine to operate at peak efficiency it must be able to provide fuel and air in the proper ratio and at a high enough engine temperature for the engine to completely burn all of the fuel. Wet stacking does usually cause any permanent damage and can be alleviated if additional load is applied to relieve the condition. It can reduce the system performance and increase maintenance. Applying an increasing load over a period of time until the excess fuel is burned off and the system capacity is reached usually can repair the condition. This can take several hours to burn off the accumulated unburned fuel.
CAUTION - ENGINE LOAD (WET-STACKING)
1
TLG-12SPX4— OPERATION AND PARTS MANUAL — REV. #1 (12/17/09) — PAGE 9
TLG-12SPX4 — RULES FOR SAFE OPERATION
DANGER - READ THIS MANUAL!
Failure to follow instructions in this manual may lead to
serious injury
or even
DEATH
! This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only.
The following safety guidelines should always be used when operating the
generator.
General Safety:
DO NOT operate or service this equipment before reading this entire manual.
The operator MUST BE familiar with proper safety precautions and operations techniques before using generator.
This equipment should not be operated by persons under 18 years of age.
NEVER operate this equipment without proper protective clothing, shatterproof glasses, steel-toed boots and other protective devices required by the job.
NEVER use accessories or attachments, which are not recommended by Multiquip for this equipment. Damage to the equipment and/or injury to user may result.
NEVER touch the hot exhaust manifold, muffler or cylinder. Allow these parts to cool before servicing engine or generators.
The engine section of this generators requires an adequate free flow of cooling air. any enclosed or narrow area where free flow of the air is restricted. If the air flow is restricted it will cause serious damage to the generators or engine and may cause injury to people. Remember the generator's engine gives off carbon monoxide gas.
NEVER
DEADLY
operate the generator in
Denyo
DANGEROUS
GAS FUMES
NEVER operate this equipment when not feeling well due to fatigue, illness or taking
medicine.
NEVER operate this equipment under the influence or drugs or alcohol.
ALWAYS wear proper respiratory (mask), hearing and eye protection equipment when operating the generator.
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
Manufacturer does not assume responsibility for any accident due to equipment modifications. Unauthorized equipment modification will void all warranties.
ALWAYS refuel in a well-ventilated area, away from sparks and open flames.
ALWAYS use extreme caution when working with flammable liquids. When refueling, stop the engine and allow it to cool. DO NOT
smoke
around or near the machine. Fire or explosion could result from fuel vapors, or if fuel is spilled on a hot engine.
NEVER operate the generator in an explosive atmosphere or near combustible materials. An explosion or fire could result causing severe
bodily
harm or even death.
NEVER disconnect any
These devices are intended for operator safety. Disconnection of these devices can cause severe injury, bodily harm or even death! Disconnection of any of these devices will void all warranties.
"emergency or safety devices"
.
PAGE 10 — TLG-12SPX4— OPERATION AND PARTS MANUAL — REV. #1 (12/17/09)
TLG-12SPX4 — RULES FOR SAFE OPERATION
ALWAYS be sure the operator is familiar with proper safety precautions and operation techniques before using generators.
NEVER leave the generator unattended, turn off engine when unattended.
Unauthorized equipment modifications will void all warranties.
ALWAYS ensure generator is on level ground before use.
DO NOT place hands or fingers inside generators engine compartment when engine is running.
NEVER run engine without air cleaner. Severe engine damage
may occur.
NEVER change or adjust the engine speed which has been
set at the factory prior to shipping.
Power Cord Safety
NEVER let power cables or cords
NEVER is being transfer to a load.
NEVER use a defective or frayed power cable. Check the cable for cuts in the insulation.
NEVER use a extension cord that is frayed or damaged where the insulation has been cut.
ALWAYS make certain that proper power or extension cord has been selected for the job See Table 6.
stand in water
while AC power from the generators
lay in wate
r.
Grounding Safety
ALWAYS make sure that electrical circuits are properly
grounded
local codes before operating generator. Severe
death!
ungrounded generator.
ALWAYS make sure the generators are properly grounded to a suitable earth ground (GROUND ROD). See installation in this manual.
per the
by electrocution can result from operating an
National Electrical Code
(NEC) and
injury
Maintenance Safety
or
NEVER lubricate components or attempt service on a running machine.
High Temperatures – Always stop engine and allow the engine to cool before adding fuel, oil or performing service and maintenance
hot!
functions. Contact with cause serious burns.
Keep the machinery in proper running condition.
Fix damage to the machine immediately and replace any broken parts immediately.
ALWAYS replace any worn or damaged warning decals.
ALWAYS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children and un-authorized personnel.
The electrical voltage required to operate the generator can cause severe injury or even death through physical contact with live circuits. performing maintenance on the generator.
Dispose of hazardous waste properly. Examples of potentially hazardous waste are used motor oil, fuel and fuel filters.
DO NOT use food or plastic containers to dispose of hazardous waste.
DO NOT pour waste, oil or fuel directly onto the ground, down a drain or into any water source.
Turn all circuit breakers OFF before
components can
ALWAYS allow the machine a proper amount of time to
cool before servicing.
ALWAYS service air cleaner frequently to prevent engine malfunction.
ALWAYS disconnect the
NEGATIVE battery terminal
before performing service on the generator.
Follow all battery safety guidelines listed in this manual when handleing or servicing the generator.
NEVER use
gas piping
as an electrical ground.
1
TLG-12SPX4— OPERATION AND PARTS MANUAL — REV. #1 (12/17/09) — PAGE 11
TLG-12SPX4 — RULES FOR SAFE OPERATION
WARNING - BURN HAZARDS
To prevent burns, DO NOT touch or open any of the below mentioned components while the engine is running or immediately after operations. Always allow sufficient time for the engine and generator to cool before performing maintenance.
Radiator Cap - Removing the radiator cap while the engine is hot will result in high pressurized, boiling water to gush out of the radiator, causing severe scalding to any persons in the general area of the generator.
Coolant Drain Plug - Removing the coolant drain plug while the engine is hot will result in hot coolant gushing out of the coolant drain plug, therefore causing severe scalding to any persons in the general area of the generator.
Engine Oil Drain Plug - Removing the engine oil drain plug while the engine is hot will result in hot oil gushing out of the oil drain plug, therefore causing severe scalding to any persons in the general area of the generator.
Battery Safety
Use the following guidelines when handling the battery:
The battery contains acids that can cause injury to the eyes and skin. To avoid eye irritation, glasses.
Use well insulated gloves when picking up the battery.
DANGER - EXPLOSION HAZARDS
The risk of an explosion exists when performing service on the battery. To avoid
■■
DO NOT drop the battery. There
■■
is the possibility of risk that the battery may explode.
■■
DO NOT expose the battery to
■■
open flames, sparks, cigarettes etc. The battery contains combustible gases and liquids. If these gases and liquids come in contact with a flame or spark, an explosion could occur.
■■
ALWAYS keep the battery charged. If the battery is not
■■
charged a buildup of combustible gas will occur.
always
wear safety
severe injury
or
DEATH:
■■
ALWAYS keep battery charging and cables in good
■■
working condition. Repair or replace all worn cables.
■■
ALWAYS recharge the battery in an vented air
■■
environment, to avoid risk of a dangerous concentration of combustible gases.
■■
In case the battery liquid (dilute sulfuric acid) comes in
■■
contact with immediately with plenty of water.
■■
In case the battery liquid (dilute sulfuric acid) comes in
■■
contact with your plenty of water and contact the nearest doctor or hospital to seek medical attention.
clothing or skin
EYES
, rinse skin or clothing
, rinse eyes immediately with
PAGE 12 — TLG-12SPX4— OPERATION AND PARTS MANUAL — REV. #1 (12/17/09)
TLG-12SPX4 — RULES FOR SAFE OPERATION
ACCIRCUIT B
REAKER
OFF
22
A
120
V
20A
120V
OFF
ON
GA-2.9R
ACCIRCUIT BREAKER
OFF
22A
120
V
20A
120V
OFF
ON
GA-2.9R
ACCIRCUIT BREAKER
OF
F
2
2
A
120
V
20A
120V
OFF
ON
GA-2.9R
DANGERDANGER
DANGER
DANGERDANGER
During operation of this generation, there exists the possibility of
electrical shock or burn
cause
severe bodily harm
DEATH!
To avoid these hazards:
NEVER use
Electrocution HazardsElectrocution Hazards
Electrocution Hazards
-
Electrocution HazardsElectrocution Hazards
electrocution
, which can
or even
damaged
or
worn
cables when connecting
Engine exhaust gases contain
,
poisonous carbon monoxide. This gas is colorless and odorless, and can cause death if inhaled. NEVER operate this equipment in a confined area or enclosed structure that does not provide ample free flow air.
equipment to the generator. Make sure power connecting cables are securely connected to the generator’s output receptacles, incorrect connections may cause damage to the generators and electrical shock.
NEVER grab or touch a live power cord with wet hands, the possibility exist of electrical shock, electrocution, and even
death!
DANGERDANGER
DANGER
DANGERDANGER
Lethal Exhaust Gas HazardsLethal Exhaust Gas Hazards
-
Lethal Exhaust Gas Hazards
Lethal Exhaust Gas HazardsLethal Exhaust Gas Hazards
DANGER
Using a generator indoors .CAN KILL YOU IN MINUTES
Generator exhaust contains carbon monoxide. This is a posion you cannot see or smell
20A
120
2900
GA-2.9R
F
A
F
2
O
2
ACCIRCUIT
120V
2900
F
A
F
2
O
2
ACCIRCUIT BREAKER
NEVER use inside a home or garage, even if doors and windows are open
Avoid other generator hazards.
2900
GA-2.9R
F
A
F
2
O
2
ACCIRCUIT BREAKER
Only use OUTSIDE and far away from windows, doors, and vents.
BREAKER
OFF
.READ MANUAL BEFORE USE
Emergencies
NEVER insert any objects into
the output receptacles during
ALWAYS know the location of the
nearest
operation. This is extremely dangerous. ALWAYS turn-off the generators and place all circuit breakers in the “OFF” position when contact with the output receptacles is required. There exist the possibility of
electrocution,
ALWAYS know the location of the nearest
first aid kit
electrical shock or burn, which can cause severe bodily harm or even death
Backfeed to a utility system can cause
electrocution
NEVER connect the generators to a
building's electrical system without a transfer switch or other approved device. All installations should be performed by
licensed electrician
a with all applicable laws and electrical codes. Failure to do so could result in electrical shock or burn causing serious injury or even death!
and or property damage.
!
in accordance
In emergencies
nearest phone or Also know the phone numbers of the nearest
ambulance, doctor
information will be invaluable in the case of an emergency.
fire extinguisher
.
.
always
know the location of the
keep a phone on the job site
and
fire department
.
. This
1
TLG-12SPX4— OPERATION AND PARTS MANUAL — REV. #1 (12/17/09) — PAGE 13
TLG-12SPX4 — RULES FOR SAFE OPERATION
If your generator is trailer mounted, please read the towing and safety requirements listed below.
Towing and Transporting Safety
To reduce the possibility of an accident while transporting the generator on public roads, always make sure the trailer that supports the generator and the towing vehicle are in good operating condition and both units are mechanically sound.
The following list of safety precautions should be followed when towing your generator:
CAUTION - FOLLOW TOWING REGULATIONS
Check with your local county or state safety towing regulations, in addition to meeting
Transportation
towing your generator.
ALWAYS shutdown engine before transporting.
Drain fuel from generator fuel tank before towing.
If generator is mounted on a trailer, make sure trailer complies with all local and state safety transportation laws. Follow the listed guidelines for basic towing techniques.
Make sure the hitch and coupling of the towing vehicle are rated equal to, or greater than the trailer "gross vehicle weight rating.”
(DOT)
Safety Towing Regulations
Towing & Transporting Safety
Department of
, before
DOT Requirements include the following:
Connect and test electric brake operation.
Secure portable power cables in cable tray with tie wraps.
The maximum speed for highway towing is 55 MPH unless posted otherwise. Recommended off-road towing is not to exceed 15 MPH or less depending on type of terrain.
Place while parked.
Use the trailer’s swivel jack to adjust the trailer height to a level position while parked.
Avoid sudden stops and starts. This can cause skidding, or jack-knifing. Smooth, gradual starts and stops will improve towing.
Avoid sharp turns.
Trailer should be adjusted to a level position at all times when towing.
Raise and lock trailer wheel stand in up position when transporting.
The maximum speed for highway towing is 55 MPH unless posted otherwise. Recommended off-road towing is not to exceed 15 MPH or less depending on type of terrain.
Place prevent tipping, while parked.
Avoid sharp turns to prevent rolling.
DO NOT transport generator with fuel in tank.
chock blocks
support blocks
underneath wheel to prevent rolling,
underneath the trailer’s bumper to
ALWAYS inspect the hitch and coupling for wear. NEVER tow a trailer with defective hitches, couplings, chains etc.
Check the tire air pressure on both towing vehicle and trailer. Also check the tire tread wear on both vehicles.
ALWAYS make sure the trailer is equipped with a "Safety Chain".
ALWAYS attach trailer’s safety chains to towing vehicle properly.
ALWAYS make sure the vehicle and trailer directional, backup, brake, and trailer lights are connected and working properly.
Trailer tires should be inflated to 50 psi cold.
PAGE 14 — TLG-12SPX4— OPERATION AND PARTS MANUAL — REV. #1 (12/17/09)
NOTE
For more saftey tips, see the trailer saftey guidelines section in this manual.
TLG-12SPX4 — INSTALLATION
Figure 2. Typical Generator Grounding Application
1
TLG-12SPX4— OPERATION AND PARTS MANUAL — REV. #1 (12/17/09) — PAGE 15
TLG-12SPX4 — INSTALLATION
Outdoor Installation
Install the generator in a area that is free of debris, bystanders, and overhead obstructions. Make sure the generator is on secure level ground so that it cannot slide or shift around. Also install the generator in a manner so that the exhaust will not be discharged in the direction of nearby homes.
The installation site must be relatively free from moisture and dust. All electrical equipment should be protected from excessive moisture. Failure to do will result in deterioration of the insulation and will result in short circuits and grounding.
Foreign materials such as dust, sand, lint and abrasive materials have a tendency to cause excessive wear to
Generator Grounding
To guard against electrical shock and possible damage to the equipment, it is important to provide a good EARTH ground.
Article 250 (Grounding) of the National Electrical Code (NEC) provides guide lines for proper grounding and specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.
NEC articles 250-64(b) and 250-66 set the following grounding requirements:
1. Use one of the following wire types to connect the generator to earth ground.
engine and alternator parts.
a. Copper - 10 AWG (5.3 mm
CAUTION - EXHAUST HAZARD
Pay close attention to ventilation when operating the generator inside tunnels and caves. The engine exhaust contains noxious elements. Engine exhaust must be routed to a ventilated area.
b. Aluminum - 8 AWG (8.4 mm2) or larger.
2. When grounding the generator (Figure 2) connect the ground cable between the lock washer and the nut on the generator and tighten the nut fully. Connect the other end of the ground cable to earth ground.
3. NEC article 250-52(c) specifies that the earth ground
Indoor Installation
rod should be buried aminimum of 8 ft. into the ground.
2
) or larger.
Exhaust gases from diesel engines are extremely poisonous. Whenever an engine is installed indoors the exhaust fumes must be vented to the outside. The engine should be installed
NOTE
at least two feet from any outside wall. Using an exhaust pipe which is too long or too small can cause excessive back pressure which will cause the engine to heat excessively and possibly burn the valves.
Mounting
The generator must be mounted on a solid foundation (such as concrete) and set firmly on the foundation to isolate vibration of the generator when it is running. The generator must set at least 6 inches above the floor or grade level (in accordance to NFPA 110, Chapter 5-4.1). DO NOT remove the metal skids on the bottom of the generator. They are to resist damage to the bottom of the generator and to maintain alignment.
When connecting the generator to any buildings electrical system ALWAYS consult with a licensed electrician.
PAGE 16 — TLG-12SPX4— OPERATION AND PARTS MANUAL — REV. #1 (12/17/09)
TLG-12SPX4 — GENERAL INFORMATION
TLG-12SPX4 Whisperwatt™ Series Familiarization Generator
The MQ Power Model TLG-12SPX4 is a 13 kW
generator
(Figure 3) that is designed as a high quality portable (requires a trailer for transport) power source for telecom sites, lighting facilities, power tools, submersible pumps and other industrial and construction machinery.
Generator Control Panel
The “Engine Operating Panel” is provided with the following:
Open Delta Excitation System
The generator is equipped with the state of the art "
Delta
" excitation system. The open delta system consist of an electrically independent winding wound among stationary windings of the AC output section.
There are four connections of the open delta A, B, C and D. During steady state loads, the power from the voltage regulator is supplied from the parallel connections of A to B, A to D, and C to D. These three phases of the voltage input to the voltage regulator are then rectified and are the excitation current for the exciter section.
■■
Warning Lamp Unit
■■ ■■
Frequency Meter (Hz)
■■ ■■
AC Ammeter (Amps)
■■ ■■
AC Voltmeter (Volts)
■■ ■■
Voltage Regulator
■■ ■■
Ignition Switch
■■ ■■
Hour Meter
■■ ■■
Fuel Gauge
■■ ■■
3-Pole, 50 amp Main Circuit Breaker
■■ ■■
“Control Box” (located behind the Gen. Control Panel)
■■
■■
Automatic Voltage Regulator
■■ ■■
Current Transformer
■■ ■■
Voltage Rectifer
■■ ■■
Starter Relay
■■
When a heavy load, such as a motor starting or a short circuit occurs, the automatic voltage regulator (AVR) switches the configuration of the open delta to the series connection of B to C. This has the effect of adding the voltages of each phase to provide higher excitation to the exciter section and thus better voltage response during the application of heavy loads.
The connections of the AVR to the AC output windings are for sensing only. No power is required from these windings.
The open-delta design provides virtually unlimited excitation current, offering maximum motor starting capabilities. The excitation does not have a " according the demands of the required load.
Engine
Output Terminal Panel
The “Engine Operating Panel” is provided with the following:
■■
120V output receptacle (5-20R) GFCI, 20A
■■ ■■
120V output receptacle (L5-30R), 30A
■■ ■■
240V output receptacle(L6-30R), 30A
■■ ■■
120/240V output receptacle (CS6369), 50A
■■ ■■
Throttle Lever
■■ ■■
Ground Terminal
■■
The TLG-12SPX4 is powered by a 3 cylinder, water cooled,
Kubota Model D902 diesel engine
to meet every performance requirement for the generator. Reference Table 2 for engine specifications.
In keeping with MQ Power's policy of constantly improving its products, the specifications quoted herein are subject to change without prior notice.
Electric Governor System
The electric governor system controls the RPMs of the en­gine. When the engine demand increases or decreases, the governor system regulates the frequency variation to ±.25%.
Extension Cables
When electric power is to be provided to various tools or loads at some distance from the generator, extension cords are normally used. Cables should be sized to allow for distance in length and amperage so that the voltage drop between the generator and point of use (load) is held to a minimum. Use the cable selection chart (Table 6) as a guide for selecting proper extension cable size.
fixed ceiling
" and responds
. This engine is designed
Open-
1
TLG-12SPX4— OPERATION AND PARTS MANUAL — REV. #1 (12/17/09) — PAGE 17
TLG-12SPX4 — MAJOR COMPONENTS
4elbaT. stnenopmoCrojaMrotareneG
.ONMETINOITPIRCSED
Figure 3. Major Components
PAGE 18 — TLG-12SPX4— OPERATION AND PARTS MANUAL — REV. #1 (12/17/09)
1ylbmessAknaTleuF
2ylbmessArotaidaRdnaenignE
3ylbmessArelffuM
4ylbmessArotareneG
5ylbmessAyre
6ylbmessAlenaPlortnoCrotareneG
ttaB
TLG-12SPX4 — GENERATOR CONTROL PANEL
Figure 4. Generator Control Panel
1
TLG-12SPX4— OPERATION AND PARTS MANUAL — REV. #1 (12/17/09) — PAGE 19
TLG-12SPX4 — GENERATOR CONTROL PANEL
The definitions below describe the controls and functions of the
Generator Control Panel
1. Frequency Meter – Indicates the output frequency in
hertz (Hz). Normally 60 Hz.
2. AC Ammeter – Indicates the amount of current the load is drawing from the generator.
3. AC Voltmeter – Indicates the output voltage present at
Output Receptacles
the
4. Voltage Regulator Control – Allows ±15% manual adjustment of the generator’s output voltage.
5. Engine Warning Display Module – This module displays the following engine failures:
A. Overheat Lamp – This lamp goes ON
when the coolant is over 239 lamp goes ON during normal operation of the generator, the generator will immediately stop. Check for possible trouble before restarting engine.
B. Low Oil Pressure Lamp – During normal
operation of the generator this lamp should remain OFF. After the oil pressure rises after start-up, the lamp will go OFF. This lamp goes ON when the oil presure drops below
7.1 PSI.If this lamp is ever lit (ON) during normal operation of the generator, the generator will immediately shutdown. Check for possible trouble before restarting engine.
(Figure 4).
.
o
F. If the
6. Hour Meter – Indicates the number of hours machine has been in use.
7. Fuel Guage – Indicates the amount of fuel in the Generator.
8. Ignition Switch – Insert ignition key into this switch to start engine.
9. Throttle Lever – This knob controls the speed of the engine.
10. Ground Terminal - Ground terminal for Output Receptacles.
11. GFCI Receptacle – Provides 120 VAC output (20 amps max).
12. Auxillary Receptacle (for L5-30R) – Provides 120 VAC output (30 amps max).
13. Auxillary Receptacle (for L6-30R) – Provides 240 VAC output (30 amps max).
14. Twist Lock Dual Voltage Receptacle (CS6369) –
Provides 120/240 VAC output (50 amps max).
18. Main Circuit Breaker – This three-pole, 50A main breaker is provided to protect the the
Receptacles
Output
from overload.
C. Low Battery Fluid Lamp – This
lamp goes ON when the battery fails to charge. If this lamp goes ON during normal operation of the generator, stop the engine and fill the battery with distilled water to the specified level.
D. Pre-Heat Lamp – This lamp
indicates when the engine is ready for starting during cold weather operating condition.
PAGE 20 — TLG-12SPX4— OPERATION AND PARTS MANUAL — REV. #1 (12/17/09)
TLG-12SPX4 — OUTPUT TERMINAL PANEL FAMILIARIZATION
Output Terminal Panel
The
Output Terminal Panel
(Figure 5) shown below is located on the right-hand side (left from control panel) of the generator. Lift up on the cover to gain access to receptacles and terminal
Output Terminal Familiarization
The “
Output Terminal Panel
following:
■■
120V GFCI receptacle @ 20 amp
■■
lugs.
■■
120V receptacle @ 30 amp
■■
■■
240V receptacle @ 30 amp
■■
■■
120/240V CS6369 receptacle @ 50 amp
■■
■■
Throttle Lever
■■
■■
Ground
■■
” (Figure 5) is provided with the
Figure 5. Output Terminal Panel
1
TLG-12SPX4— OPERATION AND PARTS MANUAL — REV. #1 (12/17/09) — PAGE 21
TLG-12SPX4 — OUTPUT TERMINAL PANEL FAMILIARIZATION
120 VAC GFCI Receptacle
This120 VAC, 20 amp GFCI (Duplex Nema 5-20R) receptacle can be used anytime the generator is in operation. Pressing
reset
the Pressing the receptacle will check the GFCI function. Both receptacles should be tested at least once a month.
button resets the GFCI receptacle after being tripped.
Test Button
Figure 6. G.F.C.I. Receptacle
(See Figure 6) in the center of the
L5-30R Twist Lock 120 VAC Receptacle (Option)
There is one L5-30R, 120 VAC 30 amp auxilliary twist-lock receptacle (Figure 8) provided on the output terminal panel.
L6-30R Twist Lock 240 VAC Receptacle (Option)
There is one L6-30R, 240 VAC 30 amp auxilliary twist-lock receptacle (Figure 9) provided on the output terminal panel.
Figure 8. 120 VAC L5-30R Twist-Lock
Auxiliary Receptacle
Twist Lock Dual Voltage 120/240 VAC Receptacle (Option)
There is one CS-6369 120/240V, 50 amp auxilliary twist-lock receptacle (Figure 7) provided on the output terminal panel. This receptacle is protected by a 50 amp circuit breaker.
Turn the control panel to obtain the desired voltage. Turning the knob clockwise will clockwise will
Figure 7. 120/240V CS6369 Twist-Lock
Auxiliary Receptacle
Figure 9. 240 VAC L6-30R Twist-Lock
Auxiliary Receptacle
voltage regulator control knob
increase
decrease
the voltage, turning the knob counter-
the voltage.
(Figure 10) on the
Figure 10. Voltage Regulator Control Knob
PAGE 22 — TLG-12SPX4— OPERATION AND PARTS MANUAL — REV. #1 (12/17/09)
Loading...
+ 50 hidden pages