MTX Audio Thunder 6304, Thunder 6152 User Manual

0 (0)

AMPLIFIER OWNER’S MANUAL

POWER

AMPLIFIERS

AMPLIFIERS

Introduction

CONGRATULATIONS...

ENGLISH

on your purchase of a new MTX Audio

 

 

Thunder Amplifier! MTX has long been

 

the industry leader in mobile enclosures

 

and speakers, and we have reached

 

new heights with the development of the

 

new MTX Thunder amplifiers. You

 

couldn’t have chosen a more reliable,

 

powerful, or better performing amplifier.

 

In fact, we back up every Thunder

 

amplifier with a three-year warranty if

 

installed by an authorized MTX Audio

 

retailer (see the warranty statement).

Your new MTX Thunder amplifier was designed, built and thoroughly tested at our state-of-the-art electronics manufacturing facility in Phoenix, Arizona. We manufacture every amplifier using the latest Intelligent Surface Mount Technology. Some of the advantages of the new design are its significant improvements to the amplifier’s electrical and mechanical properties. ISMT devices feature substantially shorter internal and external lead lengths. This reduces stray capacitance and inductance, which results in cleaner and more accurate musical reproduction with significantly less noise interference. The ISMT mounter produces amplifier boards with smaller and lighter components, which are more resistant to vibrations inherent in the automotive environment.

A word about power ratings. It is important for you to know how they stack up. MTX has chosen the most honest, most conservative way to rate our amps. We show you the RMS power, at 12.5 volts, and dynamic power at 14.4 volts. However, we go above and beyond the call of duty. We test each amplifier. The technician records the “actual” power output, and records this number on your Certified Performance Certificate. The amplifier

must meet or exceed the rated specification before we’ll ship it. No questions. No exceptions.

We want to ensure you get continuous high performance from your MTX Thunder amplifier, so we recommend that you have it professionally installed by your authorized MTX dealer.

HOW TO USE THIS MANUAL

If you are installing this amplifier yourself, we recommend that you read the manual cover- to-cover before you install it. Familiarize yourself with the features and details on the input and output panels. Make sure you have all the equipment you need. Then follow the step-by-step installation instructions included. Sample installation diagrams may be found on our website:

mtx.com

If you have any questions, write or call us: MTX Audio

4545 E. Baseline Rd. Phoenix, AZ 85042

602-438-4545 • 800-CALL MTX technical@mtx.com mtx.com

Please take a moment to register your purchase on line at mtx.com.

Please also record the serial number of your amplifier in the space provided below and keep this manual for future reference, as well as your sales receipt as proof of ownership. (The serial number of your amplifier is marked on the bottom of its metal chassis.)

Serial Number: Date of Purchase:

Features

Intelligent Surface Mount Technology

Patented PWM MOSFET Switching Power Supply (#5,598,325)

Class A 100% Discrete Driver Circuit Topology

New, more reliable high powered transformers

Pure N-Channel Design

Speaker and low level inputs inputs on Thunder6152

Color-coded wire harness for speaker-level input installation on Thunder6152

Smart-Engage™ auto turn on for easy integration with factory head units (Thunder6152 only)

Input select 2CH/4CH switch on Thunder6304 functions as a built-in Y connector

Real Time Computerized Protection Circuit

Acoustically Seamless Turn-on/Turn-off (i.e. no noise)

Continuously variable/defeatable 12dB/octave high pass, 24dB/octave mono low pass crossover (variable from 40Hz to 200Hz)

Continuously variable/selectable crossover output, switchable from full range/high pass/low pass outputs (Full range only on Thunder6304)

EBC Max on Thunder 8302, allows for control of additional subwoofer amps in a daisy chain configuration in low pass mode

Continuously adjustable and defeatable Thunder EQ Bass enhancement circuitry, centered at 40Hz

Left and right individually adjustable input sensitivity (Except for Thunder6304)

Nickel-plated, heavy duty terminal block type connectors

Unique rubber Insulated Iso-Feet™

Buffered, isolated output for daisy chaining multiple amplifiers

Specifications

THUNDER6152

RMS Power measured at 12.5 Volts DC:

37.5 Watts x 2 into a 4 Ohm load with less than 0.1% Thd+N 75 Watts x 2 into a 2 Ohm load with less than 0.1% Thd+N

150 Watts bridged into a 4 Ohm load with less than 0.1% Thd+N Dynamic Power measured at 14.4 Volts DC

90 Watts x 2 into a 4 Ohm load

165 Watts x 2 into a 2 Ohm load

325 Watts bridged into a 4 Ohm load Signal to Noise Ratio: 110dB A-Weighted Damping Factor: >200

Frequency Response: 20Hz-20kHz ± 0.25dB Maximum Input: 8Vrms

Thunder EQ: Variable Bass Boost (0-18dB) centered at 40Hz Crossover: Variable 40Hz to 200Hz, 12dB/octave high pass, 24dB/octave low pass with mono output

Dimensions: 8.3" x 9.75" x 2" (21.1cm x 24.8cm x 5.1cm)

10.7" x 9.75" x 2.1" (27.2cm x 24.8cm x 5.3cm) Including IsoFeet™

THUNDER6304

RMS Power measured at 12.5 Volts DC:

37.5 Watts x 4 into a 4 Ohm load with less than 0.3% Thd+N 75 Watts x 4 into a 2 Ohm load with less than 0.3% Thd+N

150 Watts x 2 bridged into a 4 Ohm load with less than 0.3% Thd+N Dynamic Power (IHF-202 Standard) measured at 14.4 Volts DC

90 Watts x 4 into a 4 Ohm load

165 Watts x 4 into a 2 Ohm load

325 Watts x 2 bridged into a 4 Ohm load Signal to Noise Ratio: 110dB A-Weighted Damping Factor: >200

Frequency Response: 20Hz-20kHz ± 0.25dB Maximum Input: 8Vrms

Thunder EQ: Variable Bass Boost (0-18dB) centered at 40Hz Crossover: Variable 40Hz to 200Hz, 12dB/octave high pass, 24dB/octave low pass with mono output

Dimensions: 11.5" x 9.75" x 2" (29.2cm x 24.8cm x 5.1cm)

13.9" x 9.75" x 2.1" (35.3cm x 24.8cm x 5.3cm) Including IsoFeet™

THUNDER8302

RMS Power measured at 12.5 Volts DC:

75 Watts x 2 into a 4 Ohm load with less than 0.1% Thd+N 150 Watts x 2 into a 2 Ohm load with less than 0.1% Thd+N

300 Watts bridged into a 4 Ohm load with less than 0.1% Thd+N Dynamic Power (IHF-202 Standard) measured at 14.4 Volts DC 120 Watts x 2 into a 4 Ohm load

212 Watts x 2 into a 2 Ohm load

425 Watts bridged into a 4 Ohm load Signal to Noise Ratio: 110dB A-Weighted Damping Factor: >200

Frequency Response: 20Hz-20kHz ± 0.25dB Maximum Input: 8Vrms

Thunder EQ: Variable Bass Boost (0-18dB) centered at 40Hz Crossover: Variable 40Hz to 200Hz, 12dB/octave high pass, 24dB/octave low pass with mono output

Dimensions: 9.2" x 9.75" x 2" (22.8cm x 22.8cm x 5.1cm)

11.5" x 9.75" x 2.1" (29.2cm x 24.8cm x 5.3cm) Including IsoFeet™

2

3

MTX Audio Thunder 6304, Thunder 6152 User Manual

AMPLIFIERS

1.Gain Controls – These controls are used to match the input sensitivity of the amplifier to the particular source unit that you are using. The controls are factory set to 1Vrms. Note that the Thunder6304 has a separate gain control for front and rear channels.

2.RCA Input Jacks – These RCA input jacks are for use with source units that have RCA or Line Level Outputs. An independent set of jacks are provided on the Thunder6304 for front and rear stereo inputs. A source unit with a minimum level of 200mV is required for proper operation. The use of high quality twisted pair cables is recommended to decrease the possibility of radiated noise entering the system.

3.Input Select 2CH/4CH – This switch, found on the Thunder6304, is used to match the amplifier’s input to the source unit’s output so all four channels of the amplifier are driven. If your source unit has 2 outputs (a left and right) connect them to the amplifier’s front channel inputs, and place the input select switch in the 2CH position. If your source unit has 4 outputs, (left front, left rear, and right front, right rear) connect them to the amplifier inputs and place the input select switch in the 4CH postion. In the 4CH position, the fader on your source unit will operate.

4.Speaker Level Inputs – This input, found on the Thunder6152 will allow the amplifier to operate from source units with speaker-level outputs. Output speaker leads from the source unit should be tied directly to the wire harness provided with the amplifier.

Wire harness color codes:

 

Grey / Black = Source units right negative (-)

White / Black = Source units left negative (-)

Solid Grey = Source units right positive (+)

Solid White = Source units left positive (+)

With the Smart-Engage™ auto-turn circuit, a remote turn-on wire is not necessary when connecting the speaker-level input wire harness to a high powered source unit. The amplifier will automatically turn on when music is received.

5.Frequency Control – This control is continuously adjustable from 40Hz through 200Hz. Factory setting is at 40Hz.

6.Crossover Select – This switch determines what type of signal comes out of the amp. If you select high pass, the crossover slope is 12dB/stereo. If you select low pass, your crossover slope will be 24dB/mono. Available crossover frequencies are 40-200Hz.

7.Thunder EQ – This equalization circuit is used to enhance the low frequency response of the vehicle’s interior. With up to 18 dB of boost and centered at 40Hz, the Bass EQ can be adjusted to meet your own personal taste.

8.Compression Circuit – This new circuit, found on the Thunder8302, prevents the amplifier from going into clipping, even at high SPL levels. The compression circuit allows the listener to play the amplifier at high volume levels, yet protects the speakers against the potential damage that can occur during dynamic musical passages. The circuit is switchable on/off, for those SPL competitors who run their amplifiers into clipping on purpose. Warning: Damage to speakers may occur when the compression circuit is in the off position.

9.EBC 2 – The EBC, or Electronic Bass Control, allows a remote bass control to be adjusted from the driver’s seat. If the optional EBC is installed, the bass level will be able to be adjusted to overcome noise and other interference. With EBC 2 multiple amplifiers can be controlled. (Not included on Thunder6152 or 6304)

10.RCA Output Jacks and Switch – These RCA outputs allow for a signal to be sent to other amplifiers in a daisy-chain configuration.. You can select whether the signal should be high pass , low pass or full range. In low pass mode, the RCA outputs allow for multiple bass amplifiers to be level controlled using one EBC. On the Thunder 6304, the RCA output jacks provide a line level full-range summed output of the Right Front/Right Rear and Left Front/Left Rear input signals.

4

Input Panel Layout

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

AMPLIFIERS

1. Fuses - For convenience, all amplifiers utilize ATC type fuses. For continued protection in the event that a fuse blows, replace the fuse only with the same value.

Caution: The power fuses on the amp are for protecting the amp against overdrive. To protect the vehicle’s electrical system, an additional fuse is required within 18" of the battery on the 12V+ cable.

Thunder6152 - 30A

Thunder6304 - 25A x 3

Thunder8302 - 30A x 2

2. Power Terminal – This is the main power input for the amplifier and must be connected directly to the positive terminal of the car battery for the amplifier to operate properly. See the chart below for recommended cable sizes for each amplifier. Use caution when running this cable through the car. Try to avoid the input RCA cables, antenna cabling, or other sensitive equipment as the large amount of current flowing through this cable can induce noise into your system. It is also very important to have a tight connection to ensure maximum performance.

Thunder6152 – 10 Gauge

Thunder6304 – 6 - 8 Gauge

Thunder8302 – 8 Gauge

3.Ground Terminal – A good quality ground is required for your Thunder Amplifier to operate at peak performance. A short length of cable the same gauge as your power cable should be used to attach the ground terminal directly to the chassis of the car. Always scrape or sand any painted surfaces to expose bare metal where the ground wire will attach.

4.Remote Terminal – All Thunder Amplifiers can be turned on by applying 12 volts to this terminal. Typically this voltage is supplied by a wire from the source unit marked “remote” or “electric antenna”.

5.Speaker Terminals – As shown in the wiring diagrams, be sure to observe speaker polarity through the system. Failing to wire the speakers in proper phase could result in a loss of bass response and/or poor overall sound quality. Caution: Thunder amplifiers are not recommended for loads below 2 ohms stereo or 4 ohms bridged.

6.Power LED (top of heatsink)- A lighted LED indicates that power has been applied to the amplifier. +12V from the battery to the +BATT terminal (#10) and +12V from a switched ignition or remote lead from a head unit. An unlighted LED indicates power has been removed or the amplifier has overheated. In the case of the overheat condition, the amplifier will turn back on after it cools down.

6

Output Panel Layout

 

 

 

 

 

 

 

 

 

 

 

 

 

7

AMPLIFIERS

Adjusting the Gain

1.Turn the gain controls on the amplifier all the way down.

2.Turn up the volume control on the source unit to approximately 3/4 of maximum.

3.Adjust one gain control on the amplifier until audible distortion occurs.

4.Adjust that same gain control down until audible distortion disappears.

5.Follow steps 3-4 for other gain control settings.

6.When the Thunder6152 and 8302 is bridged, adjust only the left channel gain control.

7.The amplifier is now calibrated to the output of the source unit.

Typical Speaker

Wiring

Configurations

Stereo Amplifier

Bridge Mode Application

Impedance Requirement

4 ohm bridge minimum

2 ohm stereo minimum

 

 

8 ohm

 

 

 

 

 

4 ohm

 

 

 

 

 

8 ohm

 

 

 

 

 

4 ohm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+

-

-

+

 

 

+

-

-

+

 

 

L

L

R

R

 

 

L

L

R

R

 

 

 

AMP

 

 

 

AMP

 

Two 8 ohm Speakers

Two 4 ohm Speakers

not

OK ok

Definitions of Common Terms

The following list of terms with their definitions is offered as help in understanding the set-up and operation of your amplifier.

1.Crossover (xover) - an electrical filter with high-pass or low-pass characteristics that divides the frequency range into playable bands for certain speakers. Subwoofers, midbass, midrange and tweeters are all designed to play different frequencies and should do so to avoid damage. The xover point is where the playable frequencies cross from one speaker to the next at -3dB below reference level.

2.Full-range - refers to signals which cover the entire audio frequency span from 20Hz to 20kHz.

3.High-pass - simply put, this blocks lower frequencies which damage smaller speakers, and passes the higher frequencies for smaller speakers like the midrange and tweeter.

4.Low-pass - you got it, this is the inverse of a high-pass. It blocks higher frequencies and passes the playable lower frequencies to the larger speakers, like subwoofers.

5.Impedance - the resistance to the flow of current in an alternating current circuit (such as with music). Line level circuits are typically a high impedance of several thousand ohms, while speaker level circuits are usually a low impedance of a few ohms.

6.Line level - the type of signal produced at the outputs of tape decks, CD tuners, preamplifiers, etc., with a typical value of a volt or less in a high impedance circuit.

7.Speaker level - the type of output that is meant to drive speakers. These signals are sometimes called high level and are usually connected by two conductor speaker wires

8.Signal - the signal of an audio system is what is heard from the speakers. These signals may be high pass, low pass or full-range.

We don’t have enough space for Electronics 101, so if you have a good, bad or amusing question, please call us TOLL FREE at 800-CALL MTX! (800-225-5689)

Troubleshooting Guide

Read this if you wanna be a do-it-yourselfer - or give us a call at 800-CALLMTX.

Problem

Cause

Solution

No LED indication

No +12V at remote connection

Supply +12V to terminal

 

No +12V at Power connection

Supply +12V to terminal

 

Insufficient ground connection

Verify ground connection

 

Blown power fuse

Replace fuse

LED on, no output

Volume on head unit off

Increase volume on head unit

 

Speaker connections not made

Make speaker connections

 

Gain control on amplifier off

Turn up gain

 

Signal processing units off

Apply power to signal processor

 

All speakers blown

Replace speakers

Output distorted

Head unit volume set too high

Lower head unit volume

 

Amplifier gain set too high

Lower amplifier gain

Balance reversed

Speakers wired L + R reversed

Wire speakers with correct orientation

 

RCA inputs reversed

Reverse RCA inputs

Some balance reversed

Some Speakers wired L + R

Wire speakers with correct orientation

 

reversed

 

 

Some RCA inputs reversed

Reverse appropriate RCA inputs

Bass is boomy

Thunder EQ too high

Lower setting

Bass is weak

Thunder EQ too low

Raise setting

 

Speakers wired out

Wire with correct phase

 

of phase

 

 

Not using MTX woofers

Buy MTX woofers

Blowing fuses

Excessive output levels

Lower volume

 

Amplifier defective

Return for service

8

9

AMPLIFIERS

Introduction

FRANÇAIS

FELICITATIONS...

vous félicitant de votre achat d’un nou-

 

 

veau amplificateur MTX Audio Thunder !

 

MTX a été depuis longtemps un leader

 

dans l’industrie d’enclos mobiles et

 

speakers, et nous sommes arrivés à un

 

nouveau sommet avec le développement

 

des nouveaux amplificateurs MTX

 

Thunder. Vous n’auriez pas pu choisir

 

d’amplificateur plus fiable, plus puissant

 

ou meilleur - en effet ; nous garantissons

 

pendant trois ans chaque amplificateur

 

Thunder s’il est installé par un vendeur

 

agréé (voir la garantie).

Votre nouvel amplicateur MTX Thunder a été conçu, construit et testé dans notre usine électronique de dernier cri à Phoenix, Arizona. Nous fabriquons chaque amplificateur en employant la Technologie Surface Mount le plus récent et intelligent . Quelques advantages du nouveau dessin sont les perfectionnements aux propriétés mécaniques et électriques de l’amplificateur. Les mécanismes SMT ont de substantiellement plus courtes longueurs internes et externes. Cela réduit l’inductance et la capacitance égarées, qui résulte en une reproduction musicale plus pure et plus exacte avec considérablement moins d’intervention du bruit. Le SMT mounter produit des cartes d’amplificateur avec plus petits et plus légèrs composants qui sont plus résistants aux vibrations inhérentes dans l’environnement automobile.

Un mot au sujet d’évaluations de puissance. C’est important de savoir comment elles s’y comparent. MTX a choisi la méthode la plus honnête et la plus conservatrice d’estimer les ampères. Nous vous montrons la puissance RMS, aux 12,5 volts et la puissance dynamique aux 14,4 volts. Cependant ; nous allons au-delà l’appel de devoir. Nous testons

chaque amplificateur. Le technicien enregistre la puissance de sortie ‘actuelle’, et puis il note ce nombre sur votre Certificat de Performance Attesté. L’amplificateur doit satisfaire ou dépasser les spécifications d’évaluation avant d’être envoyé. Pas de questions. Pas d’exceptions.

Nous voulons tout faire pour assurer que vous obtenez la haute performance continue de votre amplificateur MTX Thunder, donc nous vous recommandons de l’avoir installé professionellement par votre vendeur agréé.

COMMENT UTILISER CE MANUEL

Si vous installez cet amplificateur vousmême, nous vous recommandons de lire ce manuel de la première à la dernière page avant de l’installer. Familiarisez-vous avec les caractéristiques et les détails des panneaux entrée-sortie. Vérifiez que vous avez tout l’équipement dont vous avez besoin. Puis suivez les instructions d’installation point par point qui se trouvent. Vous pouvez trouver des échantillons des diagrammes d’installation sur le Web à notre site :

mtx.com

Si vous avez des questions, écrivez ou téléphonez-nous à:

MTX Audio

4545 E. Baseline Rd. Phoenix, AZ 85042 602-438-4545 800-CALL MTX technical@mtx.com mtx.com

Caractéristiques

Technologie de montage en surface intelligente

Alimentation à découpage MOSFET PWM brevetée (brevet 5 598 325)

Topologie de circuit moteur 100 % discret de classe A

Nouveaux transformateurs haute puissance plus fiables

Conception N-voies pure

Entrées de haut-parleur et de bas niveau sur Thunder 6152

Faisceau de fils codés en couleur pour installation d’entrée au niveau haut-parleur sur Thunder 6152

Mise en marche automatique Smart-Engage™ pour faciliter l’intégration avec des unités installées en usine (Thunder 6152 uniquement)

Sélecteur d’entrée 2 voies/4 voies sur Thunder 6304 fonctionnant comme un connecteur en T intégré

Circuit de protection informatisé temps réel

Marche/arrêt transparente au plan acoustique (silencieuse)

Filtre passe-haut variable et contournable continuellement, 12dB/octave, ou filtre passe-bas mono de 24 dB/octave (variable de 40 à 200 Hz)

Sortie de filtre passe-bande sélectionnable/ variable en continu, basculable entre sorties pleine gamme/passe- haut/passe-bas (pleine gamme uniquement sur Thunder 6304)

EBC Max sur Thunder 8302 permet de commander des amplis de subwoofers supplémentaires dans une configura tion en série dans un mode passe-bas

Circuit d’amplification des basses Thunder EQ Bass réglable et contournable continuellement, centré à 40 Hz

Sensibilité d’entrée individuellement réglable à gauche et à droite

Connecteurs de type bornier renforcé, plaqués nickel

Iso-Feet™ isolés uniques¸en caoutchouc

Sortie isolée avec amplificateur séparateur pour les amplificateurs multiples en série

Specifications

THUNDER6152

RMS Power measured at 12.5 Volts DC:

37.5 Watts x 2 into a 4 Ohm load with less than 0.1% Thd+N 75 Watts x 2 into a 2 Ohm load with less than 0.1% Thd+N

150 Watts bridged into a 4 Ohm load with less than 0.1% Thd+N Dynamic Power measured at 14.4 Volts DC

90 Watts x 2 into a 4 Ohm load

165 Watts x 2 into a 2 Ohm load

325 Watts bridged into a 4 Ohm load Signal to Noise Ratio: 110dB A-Weighted Damping Factor: >200

Frequency Response: 20Hz-20kHz ± 0.25dB Maximum Input: 8Vrms

Thunder EQ: Variable Bass Boost (0-18dB) centered at 40Hz Crossover: Variable 40Hz to 200Hz, 12dB/octave high pass, 24dB/octave low pass with mono output

Dimensions: 8.3" x 9.75" x 2" (21.1cm x 24.8cm x 5.1cm)

10.7" x 9.75" x 2.1" (27.2cm x 24.8cm x 5.3cm) Including IsoFeet™

THUNDER6304

RMS Power measured at 12.5 Volts DC:

37.5 Watts x 4 into a 4 Ohm load with less than 0.3% Thd+N 75 Watts x 4 into a 2 Ohm load with less than 0.3% Thd+N

150 Watts x 2 bridged into a 4 Ohm load with less than 0.3% Thd+N Dynamic Power (IHF-202 Standard) measured at 14.4 Volts DC

90 Watts x 4 into a 4 Ohm load

165 Watts x 4 into a 2 Ohm load

325 Watts x 2 bridged into a 4 Ohm load Signal to Noise Ratio: 110dB A-Weighted Damping Factor: >200

Frequency Response: 20Hz-20kHz ± 0.25dB Maximum Input: 8Vrms

Thunder EQ: Variable Bass Boost (0-18dB) centered at 40Hz Crossover: Variable 40Hz to 200Hz, 12dB/octave high pass, 24dB/octave low pass with mono output

Dimensions: 11.5" x 9.75" x 2" (29.2cm x 24.8cm x 5.1cm)

13.9" x 9.75" x 2.1" (35.3cm x 24.8cm x 5.3cm) Including IsoFeet™

THUNDER8302

RMS Power measured at 12.5 Volts DC:

75 Watts x 2 into a 4 Ohm load with less than 0.1% Thd+N 150 Watts x 2 into a 2 Ohm load with less than 0.1% Thd+N

300 Watts bridged into a 4 Ohm load with less than 0.1% Thd+N Dynamic Power (IHF-202 Standard) measured at 14.4 Volts DC 120 Watts x 2 into a 4 Ohm load

212 Watts x 2 into a 2 Ohm load

425 Watts bridged into a 4 Ohm load Signal to Noise Ratio: 110dB A-Weighted Damping Factor: >200

Frequency Response: 20Hz-20kHz ± 0.25dB Maximum Input: 8Vrms

Thunder EQ: Variable Bass Boost (0-18dB) centered at 40Hz Crossover: Variable 40Hz to 200Hz, 12dB/octave high pass, 24dB/octave low pass with mono output

Dimensions: 9.2" x 9.75" x 2" (22.8cm x 22.8cm x 5.1cm)

11.5" x 9.75" x 2.1" (29.2cm x 24.8cm x 5.3cm) Including IsoFeet™

10

11

Loading...
+ 13 hidden pages