Two-Way R
User Guide
KEM-ML34301 |
Series |
For More Information
For further information, you may call Motorola Solutions, Inc. at 1-800-638-5119 (U.S. and Canada), e-mail us at giantintl@callcenter.com or visit us on the Internet at motorolasolutions.com/talkabout.
Safety and General Information
Important Information on Safe and Efficient Operation
Read This Information Before Using Your Radio.
The information provided in this document supersedes the general safety information in user guides published prior to December 1, 2002.
Transmit and Receive Procedure
Your two-way radio contains a transmitter and a receiver. To control your exposure and ensure compliance with the general population/ uncontrolled environment exposure limits, always adhere to the following procedure:
•Transmit no more than 50% of the time.
•To receive calls, release the PTT button.
•To transmit (talk), press the Push to Talk (PTT) button.
Transmitting 50% of the time, or less, is important because the radio generates measurable RF energy exposure only when transmitting (in terms of measuring standards compliance).
Exposure to Radio Frequency Energy
Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines:
•United States Federal Communications Commission, Code of Federal Regulations; 47CFR part 2 sub-part J.
•American National Standards Institute (ANSI)/Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992.
•Institute of Electrical and Electronics Engineers (IEEE) C95. 1-1999 Edition.
•International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998.
•Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radiofrequency Electromagnetic Fields in the Frequency Range from 3 KHz to 300 GHz, 1999.
•Australian Communications Authority Radiocommunications (Electromagnetic Radiation—Human Exposure) Standard, 2003.
•ANATEL ANNEX to Resolution No. 303 of July 2, 2002.
•ANATEL ANNEX to Resolution No. 533 of September 10, 2009.
To ensure optimal radio performance and make sure human exposure to radio frequency electromagnetic energy is within the guidelines set forth in the above standards, always adhere to the following procedures.
Portable Radio Operation and EME Exposure
Antenna Care
Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could damage the radio and may violate FCC regulations.
Do NOT hold the antenna when the radio is “IN USE.” Holding the antenna affects its effective range.
Body-Worn Operation
To maintain compliances with FCC/Health Canada RF exposure guidelines if you wear a radio on your body when transmitting always place the radio in a Motorola-supplied or approved clip holder, holster, case or body harness for this product. Use of non-Motorola-approved accessories may exceed FCC/Health Canada RF exposure guidelines.
If you do not use one of the Motorola-supplied or approved body-worn accessories and are not using the radio held in the normal use position, ensure the radio and its antenna are at least 1 inch (2.5 cm) from your body when transmitting.
Data Operation
If applicable, when using any data feature of the radio with or without an accessory cable, position the radio and its antenna at least one inch (2.5 cm) from the body.
Approved Audio Accessories
•53724: Remote Speaker with Push-to-Talk Microphone
•53725: Headset with Swivel Boom Microphone
•53727: Earbud with Push-to-Talk Microphone
•53728: Flexible Ear Receiver
•56320: Earpiece with Boom Microphone
Electromagnetic Interference/Compatibility
Note: Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed or otherwise configured for electromagnetic compatibility. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1.This device may not cause harmful interference; and
2.This device must accept any interference received, including interference that may cause undesired operation.
IC Canada
The term "IC:" before the equipment certification number only signifies that the Industry Canada technical specifications were met.
Facilities
To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy.
Aircraft
When instructed to do so, turn off your radio when onboard an aircraft. Any use of a radio must be in accordance with applicable regulations per airline crew instructions.
Medical Devices – Pacemakers
The Advanced Medical Technology Association recommends that a minimum separation of 6 inches (15 cm) be maintained between a handheld wireless radio and a pacemaker. These recommendations are consistent with the independent research by and recommendations of the U.S. Food and Drug Administration.
People with pacemakers should:
•ALWAYS keep the radio more than 6 inches (15 cm) from their pacemaker when the radio is turned ON.
•Not carry the radio in the breast pocket.
•Use the ear opposite the pacemaker to minimize the potential for interference.
•Turn the radio OFF immediately if there is any reason to suspect that interference is taking place.
Medical Devices – Hearing Aids
Some digital wireless radios may interfere with some hearing aids. In the event of such interference, you may want to consult your hearing aid manufacturer to discuss alternatives.
Medical Devices – Other
If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information.
Safety and General Use While Driving
Check the laws and regulations regarding the use of radios in the area where you drive, and always obey them. If you do use your radio while driving, please:
•Give full attention to driving and to the road.
•Use hands-free operation, if available.
•Pull off the road and park before making or answering a call if driving conditions so require.
The use of a two-way radio while engaged in activities requiring concentration may cause distraction or otherwise impair your ability to safely participate in such activities. Always use technology safely.
Do not place a portable radio in the area over an air bag or in the air bag deployment area. Air bags inflate with great force. If a portable radio is placed in the air bag deployment area and the air bag inflates, the radio may be propelled with great force and cause serious injury to occupants of the vehicle.
Potentially Explosive Atmospheres
Turn off your radio prior to entering any area with a potentially explosive atmosphere. Only radio types that are especially qualified should be used in such areas as “Intrinsically Safe.” Do not remove, install or charge batteries in such areas. Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury or even death.
Note: The areas with potentially explosive atmospheres referred to above include fueling areas such as below decks on boats, fuel or chemical transfer or storage facilities, areas where the air contains chemicals or particles (such as grain, dust or metal powders) and any other area where you would normally be advised to turn off your vehicle engine. Areas with potentially explosive atmospheres are often—but not always—posted.
Blasting Caps and Areas
To avoid possible interference with blasting operations, turn off your radio when you are near electrical blasting caps, in a blasting area, or in areas posted “Turn off two-way radios.” Obey all signs and instructions.
Operational Cautions
Antennas
Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result.
Batteries
All batteries can cause property damage and/or bodily injury such as burns if a conductive material—like jewelry, keys or beaded chains— touch exposed terminals. The conductive material may complete an electrical circuit (short circuit) and become quite hot. Exercise care in handling any charged battery, particularly when placing it inside a pocket, purse or other container with metal objects.
Exercise care when removing NiMH or AA batteries. Do not use sharp or conductive tools to remove either of these batteries.
Battery Charger Safety Instructions:
Save these Instructions
1.Do not expose the charger to rain or snow.
2.Do not operate or disassemble the charger if it has received a sharp blow, or has been dropped or damaged in any way.
3.Never alter the AC cord or plug provided with the unit. If the plug will not fit the outlet, have the proper outlet installed by a qualified electrician. An improper condition can result in a risk of electric shock.
4.To reduce the risk of damage to the cord or plug, pull the plug rather than the cord when disconnecting the charger from the AC receptacle.
5.To reduce the risk of electric shock, unplug the charger from the outlet before attempting any maintenance or cleaning.
6.Use of an attachment not recommended or sold by Motorola may result in a risk of fire, electric shock or personal injury.
7.Make sure the cord is located so it will not be stepped on, tripped over or subjected to damage or stress.
1 |
MT Series |
|
8.An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in a risk of a fire and/or electric shock. If an extension cord must be used, make sure that:
• The pins on the plug of the extension cord are the same number, size and shape as those on the plug of the charger.
•The extension cord is properly wired and in good condition.
•The extension cord size is 18 AWG for lengths up to 100 feet, and 16 AWG for lengths up to 150 feet.
9.The supply cord of the AC adaptor cannot be replaced. If the cord is damaged, call customer service at 1-800-638-5119 (U.S. and Canada) or e-mail us at giantintl@callcenter.com.
Licensing Information
Your Motorola radio operates on FRS & GMRS frequencies in Canada & in the USA. For Canadian citizens, use of these frequencies is subject to the rules & regulations of Industry Canada (IC). IC requires no license when operated in Canada. For USA citizens, use is subject to the rules and regulations of the Federal Communications Commission (FCC) . The FCC requires that all operators using GMRS frequencies obtain a radio license before operating their equipment. To obtain the FCC forms, please visit the FCC’s Web site at wireless.fcc.gov/uls/index.htm?job=home to source form 605 and 159, which includes all the instructions you will need. If you wish to have the document faxed or mailed, or if you have questions, please use the following contact information:
For a fax: |
For mail service: |
If you have |
Contact the |
Call the FCC |
questions about |
Fax-0n-Demand |
Forms Hotline |
the FCC License: |
system |
|
Call the FCC |
|
|
|
1-202-418-0177 |
1-800-418-FORM |
1-888-CALL-FCC |
|
(3676) |
(225-5322) |
Changes or modifications not expressly approved by Motorola may void the user’s authority granted by the IC/FCC to operate this radio and should not be made. To comply with IC/FCC requirements, transmitter adjustments should be made only by or under the supervision of a person certified as technically qualified to perform transmitter maintenance and repairs in the private land, mobile and fixed services as certified by an organization representative of the user of those services. Replacement of any transmitter component (crystal, semiconductor, etc.) not authorized by the IC/FCC equipment authorization for this radio could violate IC/FCC rules.
Note: Use of this radio outside the country where it was intended to be distributed is subject to government regulations and may be prohibited.
Control Buttons
Emergency Alert
Volume
Push to Talk (High)
LED Indicator
Accessory Port
Push to Talk (Low)
Menu/ Keypad Lock
Call Tone
Flash Light 
MON 
Scan/Monitor
Button
MENU
Scroll/Weather
Microphone 
Mini-USB |
Speaker |
|
Charging Port |
||
|
Flash Light LED
Display Screen Guide
Numbers for Channel,
Call Tone
Numbers for Codes 
—Battery Meter |
—Vibrate |
|
|
||
—Channel Power |
—Scan |
|
Indicator |
—Dual Scan |
|
(see menu Options) |
||
|
||
|
—Call Tone, |
|
—Keypad Lock |
Keypad Tone |
|
—Talk Confirmation |
—Weather Alert |
|
|
||
Tone (Roger Beep) |
—Hands-Free Use |
|
|
||
—Noise Filtering |
Without |
|
Accessories |
||
|
||
—On/Off for each |
—Hands-Free Use |
|
feature |
||
With Accessories |
||
|
Getting Started
Weatherproof
This radio is weatherproof to IP-54 standards. It is dust/splashproof from any direction. The radio is resistant to water and rain splashes only when the battery cover and headset accessory mini-USB ports are sealed. Open the battery compartment door or headset port cover only when the radio is dry. Use of a headset accessory should be in dry environments only.
The charging base and AC adaptor are not waterproof. Do not expose the charger to rain or snow. Charge the radios only in a dry location. Do not place wet radios into the charging base. The battery door must be tightly closed with the screw to maintain the weatherproof seal of the radio.
Installing the Batteries
Each radio can use either 1 NiMH rechargeable battery pack or 3 AA alkaline batteries and beeps when the batteries are low.
Installing NiMH Rechargeable Battery Pack
1.Turn the radio off.
2.With the back of the radio facing you, loosen the retaining screw on the battery door and open the cover.
3.Remove the NiMH battery pack from the clear plastic bag (do not disassemble or unwrap the battery pack).
4.Insert the NiMH battery pack with the diagram facing you. (The ribbon should be underneath the battery pack and should wrap around the right side of the pack for easy removal.)
5.Close the battery cover and tighten the retaining screw on the battery door.
Installing the Three AA Alkaline Batteries (Optional Accessory)
1.Turn the radio off.
2.With the back of the radio facing you, loosen the retaining screw on the battery door and open the cover.
3.Insert the three AA alkaline batteries with + and - polarity as shown inside. (The ribbon should be underneath the AA alkaline batteries and should wrap around the right side of the batteries.)
4.Close the battery cover and tighten the retaining screw on the battery door.
Battery |
r |
|
adio batte |
n shows the battery charge level, from full |
|
|
en the radio has one segment left, the |
|
chirps pe |
ally or after releasing |
(Low Battery |
Alert).
Removing the NiMH Battery Pack
1.Turn the radio off.
2.With the back of the radio facing you, loosen the retaining screw on the battery door and open the cover.
3.Remove the NiMH battery pack by pulling the ribbon attached to the radio.
4.Close the battery cover and tighten the retaining screw on the battery door.
Removing the Three AA Alkaline Batteries (Optional Accessory)
1.Turn the radio off.
2.With the back of the radio facing you, loosen the retaining screw on the battery door and open the cover.
3.Gently remove each alkaline battery by easing each battery out individually.
4.Close the battery cover and tighten the retaining screw on the battery door.
Notes
•Exercise care when removing NiMH or AA batteries. Do not use sharp or conductive tools to remove either of these batteries.
•Remove the batteries before storing your radio for extended periods of time. Batteries corrode over time and may cause permanent damage to your radio.
Using the mini-USB Charging Adaptor
The mini-USB charging adaptor allows you to conveniently charge your NiMH battery pack. This is an alternative to charging your NiMH battery pack in the Battery Charger desk stand using the AC wall adaptor and especially useful when used while traveling.
Available mini-USB charging options:
1.Vehicle charger
2.Mini-USB computer cable
If using a computer, the computer must be turned on.
This and other accessories (sold separately) are available for your radio. For more information, visit our Web site at motorolasolutions.com/talkabout or shop.giantintl.com.
1.Plug your mini-USB cable or charger into a power source as is appropriate for your accessory.
2.Plug the cable into the mini-USB port on the bottom of your radio.
3.After the initial charge, an empty battery will be fully charged in 7 hrs. for the MT350 series radio (KEBT-650 mAh NiMH battery pack) or 14 hrs. for the MT352 series radio (KEBT-1300 mAh NiMH battery pack).
4.The battery icon will scroll as the battery is being charged. The scrolling icon will stop when the battery is fully charged.
Notes
•When moving between hot and cold temperatures, do not charge the NiMH battery pack until the battery temperature acclimates (usually about 20 minutes).
•For optimal battery life, remove the radio from the charger within 16 hours. Do not store the radio while connected to the charger.
•If the radio is kept on while charging, the charging time will be extended.
•Even though the charger is connected, you may not be able
to transmit a message if the battery is comple |
mpty |
. |
Allow time for the battery to charge to 1 |
|
re |
attempting to transmit a message. |
|
|
Attaching and Removing the Belt Clip
1.Attach belt clip to pocket or belt strap.
2.Align the belt clip post with the hole in the back of the radio.
3.Gently push until the clip clicks in place.
To Remove
1.Push down on the release tab at the top of the belt clip to release the catch.
2.Pull the belt clip away from the back of the radio.
Using the Desktop Battery Charger (Optional Accessory)
The battery charger provides drop-in charging convenience for NiMH batteries and can be placed on any flat surface, such as a desk or workbench. Charge the NiMH battery overnight (at least 16 hours) before using it for the first time.
MT350R Radio
After the initial charge, an empty battery (KEBT-650 mAh NiMH) is fully charged within 7 hrs.
MT352R Radio
After the initial charge, an empty battery (KEBT-1300 mAh NiMH) is fully charged within 14 hrs.
2 |
MT Series |
|
Loading...