Miele EBA 4470, EBA 4476 User Manual

0 (0)

EBA 4470

EBA 4476

Montageanweisung Installation Instructions Instructions d’installation Instrucciones de Instalación

M.-Nr. 06 735 180

EBA 4470 (70 cm)

2

Miele EBA 4470, EBA 4476 User Manual

EBA 4476

(30'')

3

EBA 4476 (30'')

de – deutsch

Achtung! EBA 4476 (30''):

Wenn der Frontausschnitt seitlich nicht bündig mit den

Außenwänden des Schrankes ist:

Die Innenseiten des Schrankumbaus müssen jeweils mit einem Holzstück aufgefüttert werden, so dass die seitlichen Kanten des Frontausschnittes mit dem eingesetzten Holzstück bündig sind.

Die beiden Holzstücke müssen eine Tiefe von mind. 70 mm haben und in der Höhe der Nischenhöhe entsprechen.

4

EBA 4476 (30'')

en – English

Important! EBA 4476 (30''):

If the sides of the front cut-out are not flush with the external walls of the trim kit:

A wooden filler panel will be required inside the trim kit on either side of the unit.

The filler panels must be at least 2 3/4" (70 mm) deep and the same height as the niche.

es – español

Importante! EBA 4476 (30''):

Si los lados del recorte delantero no están al ras con las paredes externas de la chambrana:

Se requerirá un panel de relleno de madera dentro de la chambrana, de cada lado de la unidad.

Los paneles de relleno deberán ser de por lo menos de 70 mm de profundidad y tener la misma altura que el nicho.

fr – française

Important ! EBA 4476 (30 ''):

Si les côtés du trou de découpage ne sont pas alignés avec les bords extérieurs de la garniture :

Il faudra y fixer un panneau intercalaire de chaque côté, de même hauteur et d’au moins 70 mm de profondeur.

5

CVA 4xxx + EBA 4470 (70 cm) / EBA 4476 (30'')

de – deutsch

Achtung! Einbau eines CVA 4xxx in einen EBA 4470 (70 cm) oder EBA 4476 (30'')

An der rechten Seite muss ein Holzstück entfernt werden.

aLösen Sie dazu die zwei Schrauben (1.) und die beiden Schrauben der Montagehilfe (2.).

bBefestigen Sie die Montagehilfe wieder, nachdem das Holzstück entfernt wurde.

en – English

Important! Installation of a CVA 4xxx in an EBA 4470 (70 cm) or EBA 4476 (30'')

A piece of wood must be removed from the right side.

a Loosen the two screws (1.) and the two screws of the installation kit (2.).

bAfter removing the piece of wood, reinstall the installation aid.

es – español

Importante! Instalación de un CVA 4xxx dentro de un

EBA 4470 (70 cm) o EBA 4476 (30'')

Debera retirarse un pedazo de madera del lado derecho.

aAfloje los dos tornillos (1.) y los dos tornillos de la instalación de apoyo (2.).

bDespués de retirar la pieza de madera, reinstale la instalación de apoyo.

fr – française

Important ! Installation du CVA 4xxx dans un EBA 4470 (70 cm) ou EBA 4476 (30'')

Retirer la pièce de bois du côté droit.

aDeserrer les deux vis (1.) et celles du support d’installation (2.).

bAprès avoir retiré la pièce de bois, replacer le support d’installation.

6

Loading...
+ 14 hidden pages