McCulloch TRIM MAC ST+ User Manual

0 (0)
McCulloch TRIM MAC ST+ User Manual

TrimMac ST+

GB

FR

DE

ES

IT

NL

INSTRUCTION MANUAL

IMPORTANT INFORMATION: Please read these instructions carefully and make sure you understand them before using this unit. Retain these instructions for future reference.

MANUEL D’INSTRUCTIONS

RENSEIGNEMENTS IMPORTANTS: Avant d’utiliser cet appareil, veuillez lire

atentivement les instructions et assurez--vous de les avoir comprises. Conservez les instructions pour référence ultérieure.

BETRIEBSANWEISUNG

WICHTIGE INFORMATION: Lesen Sie diese Hinweise zur Handhabung des Geräts aufmerksam durch. Verwenden Sie es erst, wenn Sie sicher sind, daß Sie alle Anweisungen verstanden haben und gut aufbewahren.

MANUAL DE INSTRUCCIONES

INFORMACIÓN IMPORTANTE: Lea atentamente las instrucciones y asegúrese de entenderlas antes de utilizar esta aparato. Conserve las instrucciones para la referencia en el futuro.

LIBRETTO D’ISTRUZIONI

INFORMAZIONI IMPORTANTI: Siete pregati di leggere attentamente questo istruzioni e prendere dimestichezza con il prodotto prima di usario. Mantenga queste istruzioni per riferimento futuro.

HANDLEIDING

BELANGRIJKE IMPORTANTS: Lees deze instructies zorgvuldig en wees er

zeker van dat uze begrijpt alvorens de trimmer te gebruiken en bewaar ze voor toekomstige raadpleging.

115296626 Rev. 3 1/15/11 BRW

IDENTIFICATION (WHAT IS WHAT?)

Muffler

Trimmer

Assist handle

Throttle

Shield

 

Manual

Start lever

 

 

Fuel tank

Wrench

 

 

Starter handle

IDENTIFICATION OF SYMBOLS

A. WARNING! This trimmer can be dangerous! Careless or improper use can cause serious or even fatal injury.

B.Read and understand the instruction manual before using the trimmer.

C.With this handle, only use trimmer head. Never use blades or flailing devices with this tool.

D.WARNING! The trimmer line can throw objects violently. You can be blinded or injured. Always wear eye protection.

E.Always use: Ear protection

Protective glasses or visor

F.Assist handle to be positioned only below the arrow.

G.The operator of the machine must insure that no one comes within a 15 meter radius while working. When several operators are working within the same area a safety distance of at least 15 meters must be observed.

H.Use unleaded or quality leaded petrol and two--stroke oil mixed at a ratio of 2.5%.

I.Engine ON/OFF Switch.

J.Guaranteed sound power level according to Directive 2000/14/EC

K.Maximum rotational frequency of the spindle, rpm

L.Sound pressure level at 7,5 meters

2

SAFETY RULES

WARNING: When using gardening

appliances, basic safety precautions should always be followed to reduce the risk of fire and

serious injury. Read and follow all instructions.

This power unit can be dangerous! Operator is responsible for following instructions and warnings on unit and in manual. Read entire instruction manual before using unit! Be thoroughly fa-

miliar with the controls and the proper use of the unit. Restrict the use of this unit to persons who read, understand, and follow instructions and warnings on unit and in manual. Never allow children to operate this unit.

INSTRUCTION

SAFETY INFORMATION

MANUAL

ON THE UNIT

DANGER: Never use blades, wire, or

flailing devices. This unit is designed for line trimmer use only. Use of any other accessories or attachments will increase the risk of injury.

WARNING: Trimmer line throws ob-

jects violently. You and others can be blinded/ injured. Wear safety glasses and leg protection. Keep body parts clear of rotating line.

Keep children, bystanders, and animals 15 meters away. If approached stop unit immediately.

If situations occur which are not covered in this manual, use care and good judgement. If you need assistance, contact your authorized service dealer.

OPERATOR SAFETY

WARNING: This machine produces

an electromagnetic field during operation. Under some circumstances, this field may interfere with active or passive medical implants. To reduce the risk of serious or fatal injury, we recommend persons with medical implants to consult their physician and the medical implant manufacturer before operating this machine.

S Dress properly. Always wear safety glasses or similar eye protection when op-

erating, or performing maintenance, on your unit (safety glasses are available). Eye protection should be marked Z87.

SAlways wear face or dust mask if operation is dusty.

S Always wear heavy, long pants, long sleeves, boots, and gloves. Wearing safety leg guards is recommended.

S Always wear foot protection. Do not go barefoot or wear sandals. Stay clear of

spinning line.

SSecure hair above shoulder length. Secure or remove loose clothing or clothing with loosely hanging ties, straps, tassels, etc. They can be caught in moving parts.

SBeing fully covered also helps protect you from debris and pieces of toxic plants

thrown by spinning line.

SStay Alert. Do not operate this unit when you are tired, ill, upset or under the influence of alcohol, drugs, or medication. Watch what you

are doing; use common sense. S Wear hearing protection.

S Mufflers fitted with catalytic converters get

very hot during use and remain so for some time after stopping. This also applies at idle speed. Contact can result in burns to the skin. Remember the risk of fire!

S Mufflers fitted with catalytic converters get very hot during use and remain so for some time after stopping. This also applies at idle speed. Contact can result in burns to the skin. Remember the risk of fire!

S Never start or run inside a closed room or

building. Breathing exhaust fumes can kill. S Keep handles free of oil and fuel.

UNIT / MAINTENANCE SAFETY

S Disconnect the spark plug before performing maintenance except carburetor adjustments.

S Look for and replace damaged or loose parts before each use. Look for and repair fuel leaks before use. Keep in good working condition.

S Replace trimmer head parts that are chipped, cracked, broken, or damaged in any other way before using the unit.

S Maintain unit according to recommended procedures. Keep cutting line at proper length.

SUse only 2 mm diameter McCulloch brand line. Never use wire, rope, string, etc.

SInstall required shield properly before using the unit. Use only specified trimmer head;

make sure it is properly installed and securely fastened.

SMake sure unit is assembled correctly as shown in this manual.

S Make carburetor adjustments with lower end supported to prevent line from contacting any object.

SKeep others away when making carburetor adjustments.

3

SUse only recommended McCulloch accessories and replacement parts.

SHave all maintenance and service not explained in this manual performed by an authorized service dealer.

FUEL SAFETY

S Mix and pour fuel outdoors.

S Keep away from sparks or flames. S Use a container approved for fuel.

SDo not smoke or allow smoking near fuel or the unit.

S Avoid spilling fuel or oil. Wipe up all fuel spills.

SMove at least 3 meters away from fueling site before starting engine.

S Stop engine and allow to cool before removing fuel cap.

S Always store gasoline in a container approved for flammable liquids.

CUTTING SAFETY

WARNING: Inspect the area before

each use. Remove objects (rocks, broken

glass, nails, wire, etc.) which can be thrown by or become entangled in line. Hard objects can damage the trimmer head and be thrown causing serious injury.

S Use only for trimming, scalping, mowing and sweeping. Do not use for edging, pruning or hedge trimming.

S Keep firm footing and balance. Do not overreach.

SKeep all parts of your body away from muffler and spinning line. Keep engine below waist level. A hot muffler can cause serious burns.

SCut from your left to your right. Cutting on right side of the shield will throw debris

away from the operator.

S Use only in daylight or good artificial light. S Use only for jobs explained in this manual.

TRANSPORTING AND STORAGE

SAllow the engine to cool; secure unit before storing or transporting in vehicle.

SEmpty fuel tank before storing or transporting the unit. Use up fuel left in the carburetor by starting engine and letting it run until it

stops.

SStore unit and fuel in an area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

S Store unit so line limiter cannot accidentally cause injury. Unit can be hung by the shaft.

S Store the unit out of the reach of children. S Secure the machine during transport.

SPECIAL NOTICE: Exposure to vibrations

through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or abnormal swellings. Prolonged use in cold weather has been linked to blood vessel damage in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength,

change in skin color or texture, or loss of feeling in the fingers, hands, or joints, discontinue the use of this tool and seek medical attention. An anti-vibration system does not guarantee the

avoidance of these problems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condition of this tool.

ASSEMBLY

WARNING: Make sure unit is proper-

ly assembled and all fasteners are secure. Examine parts for damage. Do not use damaged parts.

It is normal for the fuel filter to rattle in the empty fuel tank.

Finding fuel or oil residue on muffler is normal due to carburetor adjustments and testing done by the manufacturer.

ADJUSTING THE HANDLE

WARNING: When adjusting the assist

handle, be sure it remains above the safety label and below the mark or arrow on the shaft.

1.Loosen wing nut on handle.

2.Rotate the handle on the shaft to an upright position; retighten wing nut.

ATTACHING THE SHIELD

WARNING: The shield must be properly installed. The shield provides partial

protection from the risk of thrown objects to the operator and others and is equipped with a line limiter which cuts excess line. The line limiter (on underside of shield) is sharp and can cut you.

1.Remove nut from shield.

2.Insert bracket into slot on shield.

3.Pivot shield until bolt passes through hole in bracket.

4.Reinstall nut and tighten securely with wrench (provided).

Slot Bracket

Nut

Gearbox

PIVOT

Shield

4

Loading...
+ 8 hidden pages