Maytag YMHWE251, YMHWE301, YMHWE201 User Manual

Use & Care Guide

Guide d’utilisation et d’entretien

FRONT-LOADING AUTOMATIC WASHER

LAVEUSE AUTOMATIQUE À CHARGEMENT FRONTAL

Models/Modèles

YMHWE201**

YMHWE251**

YMHWE301**

If you have any problems or questions, visit us at www.maytag.ca

Pour tout problème ou question, consulter www.maytag.ca

Designed to use only HE

High Efficiency detergents.

Conçue pour l’utilisation d’un détergent HE haute efficacité seulement.

Certified to Sanitize and to Reduce Allergens Homologué pour assainir et pour réduire la présence d’allergènes

NSF Model/Modèle YMHWE301**

W10484488A

Table of Contents

WASHER SAFETY..........................................................	2
ACCESSORIES..............................................................	3
CONTROL PANEL AND FEATURES.............................	4
CYCLE STATUS INDICATORS......................................	6
CYCLE GUIDE................................................................	7

USING YOUR WASHER.................................................	9
WASHER MAINTENANCE...........................................	12
TROUBLESHOOTING..................................................	15
WARRANTY.................................................................	22
ASSISTANCE OR SERVICE.........................	Back Cover

Table des matières

SÉCURITÉ DE LA LAVEUSE.......................................	23
ACCESSOIRES..............................................................	3
TABLEAU DE COMMANDE ET
CARACTÉRISTIQUES.................................................	24
TÉMOINS LUMINEUX DE PROGRAMME..................	26
GUIDE DES PROGRAMMES.......................................	27

UTILISATION DE LA LAVEUSE	...................................30
ENTRETIEN DE LA LAVEUSE.....................................	34
DÉPANNAGE................................................................	37
GARANTIE....................................................................	46
ASSISTANCE OR SERVICE.............	Couverture arrière

WASHER SAFETY

2

	ACCESSORIES	ACCESSOIRES
	Customize your new washer and dryer with the following	Personnalisez votre nouvelle laveuse et sécheuse grâce
	genuine Maytag® accessories. For more information on options	aux authentiques accessoires Maytag® suivants. Pour plus
	and ordering, contact your dealer, call us at 1-800-807-6777, or	d’informations sur les options et sur les possibilités de
	visit: www.maytag.ca.	commande, contactez votre revendeur, appeler le
	15" Pedestal	1-800-807-6777, ou consultez : www.maytag.ca.
	Color-matched pedestals raise
	the washer and dryer to a more	Stack Kit
	comfortable working height.	If space is at a premium, the stack
	The large drawer provides
		kit allows the dryer to be installed
	convenient storage.
		on top of the washer.
	Piédestal de 15"	Ensemble de superposition
	Les piédestaux aux coloris assortis
		Si l’espace disponible est restreint,
	surélèvent la laveuse et la sécheuse
		l’ensemble de superposition
	pour les amener à une hauteur
		permet à la sécheuse d’être
	d’utilisation plus confortable.
		installée par dessus la laveuse.
	Le grand tiroir offre une capacité
	de rangement pratique.

Worksurface

The worksurface bridges the washer and dryer, and provides a convenient working and storage area.

Surface de travail

La surface de travail établit la liaison entre la laveuse et la sécheuse et offre une zone de travail et d’entreposage pratique.

3

CONTROL PANEL AND FEATURES

Not all features and cycles are available on all models.

Model YMHWE301**

1	2	3

8	7	5	4
		6

Models YMHWE201** and YMHWE251**
1	2	3
8		5	4
	6

1POWER/CANCEL BUTTON

Press to turn the washer on and off. Press to stop/cancel a cycle at any time.

2WASH CYCLE KNOB

Turn the Wash Cycle knob to select a cycle for your laundry load. See “Cycle Guide” for detailed descriptions of cycles that best suit your load.

3START/PAUSE BUTTON

Press and hold to start a cycle, or press once while a cycle is in process to pause and press again to continue the cycle. If you do not press START/PAUSE within 5 minutes

of choosing a cycle, the washer automatically shuts off.

4LED DISPLAY AND SETTINGS BUTTONS

When you select a cycle, its default settings will light up and the Estimated Time Remaining will be displayed.

Use the buttons along the bottom of the display to adjust settings. See “Cycle Guide” for available settings on each cycle. Not all settings are available with all cycles.

Cycle Status Indicators

The Cycle Status Indicators show the progress of a cycle. See “Cycle Status Indicators” for additional information about each step.

Temp Level

The recommended wash temperature is preset for each cycle. You may also select a wash temperature based on the type of fabric and soils being washed. For best results, use the warmest wash water safe for your fabric, following the garment label instructions. All wash temperatures feature a cold rinse.

Spin Speed

This washer automatically selects the spin speed based on the cycle selected. Preset speeds can be changed.

•Faster spin speeds mean shorter drying times, but may increase wrinkling in your load.

•Slower spin speeds reduce wrinkling, but will leave your load more damp.

Soil Level

Soil Level (wash time) is preset for each wash cycle. As you press the Soil Level button, the cycle time will increase or decrease in the Estimated Time Remaining display.

For most loads, use the Soil Level that is preset with the cycle you have chosen. For heavily soiled and sturdy fabrics, press Soil Level to select more wash time. For lightly soiled and delicate fabrics, press Soil Level to select less wash time. Lower soil level settings will help reduce tangling and wrinkling.

4

5ADDITIONAL OPTIONS

Use these buttons to activate additional wash options or additional features on the washer. Not all options are available on all models. See the “Cycle Guide” for information on which cycles include which options.

Delay Start

Use this button to delay the start of the wash cycle. Press DELAY START until the desired time (in hours) shows in the Estimated Time Remaining display. Press START/PAUSE. The countdown to the wash cycle will show in the display window.

2nd Rinse

A 2nd rinse can be used to aid in the removal of detergent residue from garments. All rinses are cold. It is automatic for the Whitest Whites cycle. You may select or deselect by pressing button until 2nd Rinse light glows.

Prewash

This portion of the cycle adds tumbling time prior to the selected main cycle. The washer continues automatically from prewash into the main wash cycle.

Cycle Signal

This cycle signal is helpful when you are removing items from the washer as soon as it stops. Select ON or OFF.

NOTE: On some models, press CYCLE SIGNAL to operate the Control Lock feature.

6Control Lock

Press and hold for 3 seconds to lock the controls to avoid unwanted changes or operation. Press and

hold 3 seconds again to unlock. The indicator will light to show when controls are locked. You may still press START/ PAUSE to pause the cycle, or press the POWER/CANCEL button to turn the washer off.

7Sanitize (with extra hot temp) (Model YMHWE301** only)

Use Sanitize option to clean heavily soiled, colorfast fabrics. This option combines a super hot water temperature to help ensure the removal of heavy soils and stains. It is recommended that you set your hot water heater to 120°F (49°C) to ensure proper performance during this option.

8Fresh Spin™ option

Use this option if you are unable to unload your clothes

as soon after the wash cycle ends. Fresh Spin™ option provides periodic tumbling for up to 6 hours to help freshen your clothes. The “Done” indicator light will be on, the door remains locked, and the Fresh Spin™ indicator light

will flash. The Fresh Spin™ option will automatically stop and release the door lock after time expires, or if POWER/ CANCEL is pressed at anytime.

NOTES:

•Fresh Spin™ option may be used without running a cycle. Press and hold the FRESH SPIN™ button for 3 seconds, then press START/PAUSE.

•Fresh Spin™ option is not available if the Spin Speed is set to No Spin.

9DISPENSER DRAWER

The dispenser drawer gives you the convenience of automatically adding HE detergent, liquid chlorine bleach, and liquid fabric softener to the wash load at the proper time. See “Using the Dispenser” for information on using the dispenser drawer.

C

D

A

B

ARelease lever

Press down to remove the dispenser drawer.

BHigh Efficiency “HE” detergent compartment

This compartment holds liquid or powdered HE detergent for your main wash cycle.

Liquid or powdered color-safe bleach or Oxi booster product may be added to the HE detergent compartment along with the same type of detergent, liquid or powdered. Do not mix powdered and liquid products in the HE detergent compartment.

CLiquid chlorine bleach compartment

Automatically dilutes and dispenses liquid chlorine bleach at the optimum time during the first rinse after the wash cycle. This compartment cannot dilute powdered bleach.

DLiquid fabric softener compartment

Automatically dilutes and dispenses liquid fabric softener at the optimum time in the cycle.

NOTE: Use only liquid fabric softener in this dispenser.

5

CYCLE STATUS INDICATORS

The Cycle Status Indicators show the progress of a cycle. At each stage of the process, you may notice sounds or pauses that are different from traditional washers.

Add Clothes

When Add Clothes is lit, you may pause the washer, open the door, and add 2 or 3 additional items.

Controls Locked

The CONTROLS LOCKED avoids unintended use of the washer. You can also use the controls locked feature to avoid unintended cycle or option changes during a cycle. When controls locked is lit, all buttons are disabled except for START/PAUSE, POWER/CANCEL, and CYCLE SIGNAL.

Prewash

This portion of the cycle adds tumbling time prior to the selected main cycle. The washer continues automatically from prewash into the main wash cycle.

Wash

This is the main portion of the wash cycle. You will see the washer tumble the load. The motor sounds may change at different stages in the cycle. The wash time is determined by the selected cycle, along with your load size.

Rinse

You will hear sounds similar to the wash cycle as the washer rinses and moves the load. If used, liquid chlorine bleach is added in the first rinse. Fabric softener is added in the last rinse.

Spin

The washer spins the load at increasing speeds for proper water removal, based on the selected cycle and spin speed.

Done

Once the cycle is complete, this light will come on. Remove the load promptly for best results.

Fresh Spin™

The “Done” indicator remains activated, the door remains locked, and the Fresh Spin™ status light will flash.

6

CYCLE GUIDE — STANDARD CYCLES

Settings and options shown in bold are default settings for that cycle. For best fabric care, choose the cycle that best fits the load being washed. Not all cycles and options are available on all models.

For best performance, not all settings are available with each cycle, and some options cannot be used together.

Items to wash	Cycle:	Wash	Spin	Soil	Available	Cycle Details:
using default cycle		Temp.*:	Speed:	Level:	Options:
settings:
Sturdy garments	Allergen†	Hot	Ex High	Ex Heavy 1	Delay Start	Uses more water to flush out allergens
and household items		Warm 1	High	Heavy	2nd Rinse	such as dust mites and pet dander from
exposed to possible		Cold 1	Medium	Normal	Cycle Signal	normally-soiled items.
allergens			Low	Light 1	Fresh Spin™
Overly soiled	Power Wash	Hot	High	Ex Heavy 1	Delay Start	This cycle combines high and medium
garments, items		Warm	Medium	Heavy	2nd Rinse	tumbling action, with High spin speed
that need additional		Cold	Low	Normal	Prewash	and additional water in last rinse to flush
cleaning effort				Light	Cycle Signal	excess dirt from the load. For better
					Fresh Spin™	results, use this cycle combined with
						Ex Heavy 1 or Heavy Soil Level.
Heavily soiled white	Whites	Ex Hot 1	Ex High	Ex Heavy 1	Delay Start	This cycle combines fast-speed
fabrics and garments		Hot	High	Heavy	2nd Rinse	tumbling and extra high-speed spin to
		Warm	Medium	Normal	Prewash	shorten drying time. It can be used with
		Cold	Low	Light	Cycle Signal	medium and large loads. Includes 2nd
					Fresh Spin™	Rinse option.
					Sanitize††
Sturdy colorfast fabrics	Heavy Duty	Ex Hot 1	Ex High	Ex Heavy 1	Delay Start	This cycle combines fast-speed
and heavily soiled		Hot	High	Heavy	2nd Rinse	tumbling, longer wash time, and extra
garments, towels, and		Warm	Medium	Normal	Prewash	high-speed spin to shorten drying
jeans		Cold	Low	Light	Cycle Signal	times. It is designed for medium and
					Fresh Spin™	large loads.
					Sanitize††
Normally soiled	Normal	Hot	Ex High	Ex Heavy 1	Delay Start	This cycle combines medium-speed
cottons, linens,		Warm	High	Heavy	2nd Rinse	tumbling and extra high-speed spin,
sheets, and mixed		Cold	Medium	Normal	Prewash	and a load cooling process to reduce
garment loads				Light	Cycle Signal	wrinkling.
					Fresh Spin™
Bright and dark color	Cold Wash	Cold	Ex High	Ex Heavy 1	Delay Start	This cycle combines concentrated
garments			High	Heavy	2nd Rinse	fast-speed tumbling followed by
			Medium	Normal	Prewash	medium-speed wash and provides
			Low	Light	Cycle Signal	optimal cleaning while saving hot water.
			No Spin		Fresh Spin™
Normally soiled	Comforters	Hot	Ex High	Ex Heavy 1	Delay Start	This cycle starts with a soak to
blankets and		Warm	High	Heavy	2nd Rinse	thoroughly saturate your large load.
comforters		Cold	Medium	Normal	Prewash	This is followed by medium wash action
			Low	Light	Cycle Signal	and medium-spin speeds to maintain
			No Spin		Fresh Spin™	load balance.
Small loads of 3-5	Rapid Wash	Hot	Ex High	Heavy	Delay Start	This cycle combines fast-speed
lightly soiled		Warm	High	Normal	2nd Rinse	tumbling, a shortened wash time,
garments		Cold	Medium	Light	Cycle Signal	and extra high-speed spin to reduce
			Low		Fresh Spin™	drying time.
Sheer fabrics,	Delicate	Warm	Medium	Ex Heavy 1	Delay Start	This cycle combines low-speed
lingerie, sweaters,		Cold	Low	Heavy	2nd Rinse	tumbling and low-speed spin for
and special care				Normal	Cycle Signal	gentle fabric.
items marked “Hand				Light	Fresh Spin™
Washable”
Silk or ultra delicate	Silk	Warm	Low	Normal	Delay Start	This cycle gently tumbles and drains
fabrics labeled as		Cold	No Spin	Light	2nd Rinse	with the lowest spinning to gently clean
machine washable					Cycle Signal	garments and minimize wrinkling.
					Fresh Spin™

* All temperature selections feature a cold rinse.

1 Setting on YMHWE301** model. See “Control Panel and Features” for additional information.

Models: YMHWE201** and YMHWE251**

† Allergen cycle removes more than 95.0% of common allergens based on independent 3rd party laboratory testing.

Model: YMHWE301**

†Allergen

Allergen cycle certified by NSF International, an independent, third party testing and certification organization. The certification verified that this cycle reduced tested allergens by at least 95.0% and maintained the water temperature necessary to kill dust mites. Only the Allergen cycle has been designed to meet the requirements of NSF Protocol P351 for Allergen Reduction Performance effectiveness.

††Sanitize option

This washer has a Sanitize option that is certified by NSF International, an independent, third party testing and certification organization. The certification verifies that this option eliminates 99.9% of bacteria typically found on clothing, bedding, and towels. There is no

carryover of bacteria between loads after the option is complete.

Only the Sanitize option has been designed to meet the requirements of NSF Protocol P172 Sanitization Performance of Residential and Commercial, family sized clothes washer.

Use the Sanitize option to clean heavily soiled, colorfast fabrics. This option combines a super hot water temperature to help ensure the removal of heavy soils and stains. It is recommended that you set your hot water heater to 120°F (49°C) to ensure proper performance during this option.

7

CYCLE GUIDE — SPECIAL-PURPOSE CYCLES

Settings and options shown in bold are default settings for that cycle. For best fabric care, choose the cycle that best fits the load being washed. Not all cycles and options are available on all models.

For best performance, not all settings are available with each cycle, and some options cannot be used together.

Items to wash	Cycle:	Wash	Spin	Soil	Available	Cycle Details:
using default cycle		Temp.*:	Speed:	Level:	Options:
settings:
Swimwear, items that	Rinse/Drain	Cold	Ex High		Delay Start	This cycle adds water followed by a
need rinsing only.	& Spin		High		2nd Rinse	high-speed tumbling. For some fabrics
			Medium		Cycle Signal	you may wish to set the spin speed to
			Low		Fresh Spin™	a lower setting.
Wet load of clothes	Rinse/Drain	N/A	Ex High		Delay Start	To use Rinse/Drain & Spin deselect 2nd
	& Spin		High		2nd Rinse	Rinse option. Use this cycle to get water
			Medium		Cycle Signal	extracted from clothes or you want
			Low		Fresh Spin™	additional extraction on a washed load.
						Using Drain & Spin. Use this cycle with
						medium and large loads.
All loads	Soak	Warm	No Spin		Delay Start	This cycle provides a soak with short
		Cold			Cycle Signal	tumbling phase and a soaking time
						that help improve the removal of stains,
						without drum followed by drain. Drain
						without spin assures gentle treatment.
No clothes in washer	Clean	N/A	High		Delay Start	Use this cycle every 30 washes to keep the
	Washer with				Cycle Signal	inside of your washer fresh and clean. This
	affresh®					cycle uses a higher water level. Use with
						affresh® Washer Cleaner tablet or liquid chlorine
						bleach to thoroughly clean the inside of your
						washer. This cycle should not be interrupted.
						See “Washer Care.”
						IMPORTANT: Do not place garments or other
						items in the washer during the Clean Washer
						with affresh® cycle. Use this cycle with an
						empty wash tub.

* All temperature selections feature a cold rinse.

Load Size Recommendations

NOTE: A single item, bulky items, or tightly packing may cause imbalance. Add items or try to evenly distribute wet laundry in the drum, and start a Rinse/Drain & Spin cycle. If the laundry is still wet, take half of the load out of the washer and try again.

For best results, follow the load size recommendations noted for each cycle. Small load: Fill the washer drum with 3-5 items, not more than 1/4 full.

Medium load: Fill the washer drum up to about 1/2 full.

Large load: Fill the washer drum up to about 3/4 full.

Extra-large load: Fill the washer drum, but make sure clothes can tumble freely.

For best results, avoid packing tightly.

8

USING YOUR WASHER

Choosing the Right Detergent

Use only High Efficiency detergents. The package will be marked “HE” or “High Efficiency.” Low-water washing creates excessive sudsing with a regular non-HE detergent. Using regular detergent will likely result in longer cycle times and reduced rinsing performance. It may also result in component failure and, over time, build-up of mold or mildew. HE detergents are made to produce the right amount of suds for the best performance. Follow the manufacturer’s instructions to determine the amount of detergent to use.

Use only High Efficiency (HE) detergent.

IMPORTANT:

nEmpty pockets. Loose change, buttons, or any small object can plug pumps and may require a service call.

nClose zippers, fasten hooks, tie strings and sashes, and remove non-washable trim and ornaments.

nMend rips and tears to avoid further damage to items during washing.

nTurn knits inside out to prevent pilling. Separate lint-takers from lint-givers. Synthetics, knits, and corduroy fabrics will pick up lint from towels, rugs, and chenille fabrics.

nDo not dry garments if stains remain after washing, because heat can set stains into fabric.

nAlways read and follow fabric care labels and laundry product instructions. Improper usage may cause damage to your garments.

First wash cycle without laundry

Before washing clothes for the first time, if not completed during the final installation step, choose the Rapid Wash cycle and run it without clothes. Use only HE detergent. Use 1/2 the manufacturer’s recommended amount for a medium-size load. This initial cycle serves to ensure the interior is clean before washing clothes.

1. Sort and prepare your laundry

Sort items by recommended cycle, water temperature, and colorfastness. Separate heavily soiled items from lightly soiled. Separate delicate items from sturdy fabrics. Treat stains promptly and check for colorfastness by testing stain remover

products on an inside seam.

2. Load laundry into washer

Open the washer door. Place a load of sorted clothes loosely in the washer. Items need to move freely for best cleaning and to reduce wrinkling and tangling. Close the washer door by pushing it firmly until the latch clicks.

nDepending on load type and cycle, the washer can be fully loaded, but not tightly packed. Washer door should close easily. See “Cycle Guide” for loading suggestions.

nMix large and small items and avoid washing single items. Load evenly.

nWash small items in mesh garment bags. For multiple items, use more than one bag and fill bags equally.

9

Using the Dispenser

To use the dispenser drawer:

1.Open the dispenser drawer.

2.Add laundry products as described in steps 3–5.

3.Slowly close the dispenser drawer. Make sure it is completely closed.

NOTE: A small amount of water may remain in the dispensers from the previous wash cycle. This is normal.

3. Add HE detergent to dispenser

Add liquid or powdered HE detergent to this compartment.

Color-safe bleach or oxi products may be added to this compartment along with the same type of detergents.

NOTE: Do not mix powdered products with liquid ones.

HE detergent compartment

Use only High Efficiency (HE) detergent.

Do not overfill; adding too much

detergent may cause detergent to be dispensed into the washer too early.

IMPORTANT: Use powdered detergent when using the DELAY START option. Liquid detergent may seep out before the wash begins.

4. Add fabric softener to dispenser (if desired)

Liquid fabric

softener

compartment

Pour a measured amount of liquid fabric softener into liquid fabric softener compartment. Always follow manufacturer’s directions for correct amount of fabric softener based on your load size.

Fabric softener is always dispensed in the last rinse, even if 2nd Rinse is selected.

IMPORTANT: Do not overfill, dilute, or use more than 1/4 cup (60 mL) of fabric softener. Do not fill past the MAX line. Overfilling dispenser will cause fabric softener to immediately dispense into washer.

nDo not spill or drip any fabric softener onto the clothes.

nDo not use liquid fabric softener dispenser balls in this washer. They will not dispense correctly.

5.Add liquid chlorine bleach to dispenser (if desired)

Liquid chlorine

bleach

compartment

Add a measured amount of liquid chlorine bleach to the bleach compartment. Do not overfill, dilute, or use more than 2/3 cup (165 mL). Use a measuring cup with a pour spout; do not guess.

nDo not fill beyond the “MAX” level. Overfilling will cause bleach to dispense too soon and may cause garment damage.

nDo not add color-safe bleach or oxi-product to this dispenser.

10

6. Press POWER/CANCEL to turn on washer

9. Select additional options, if desired (on some models)

Slowly close the dispenser drawer. Make sure the drawer is closed completely, then press and hold POWER/CANCEL to turn on the washer. To cancel a cycle press POWER/CANCEL, then the washer powers down, the door unlocks, and clothes can be removed.

7. Select CYCLE

Model YMHWE301** shown

Turn cycle knob to select your wash cycle. See “Cycle Guide” for details on cycle features. Not all options and settings are available on all cycles.

8. Adjust cycle settings, if desired

Model YMHWE301** shown

The display will show the default settings for the selected cycle. If desired, press the button beneath each setting to adjust the Temp Level, Spin Speed, and Soil Level. Tightly packing, unbalanced loads, or excessive suds may also cause the washer to increase the cycle time.

NOTE: Not all settings are available on all cycles. See “Cycle Guide” for available settings.

Model YMHWE301** shown

To add additional options to the cycle, press the button for the desired option until light glows to add them to the selected cycle.

NOTE: Not all options are available with all cycles. See “Cycle Guide” for available options.

Delay Start

If you do not want to begin a cycle immediately, you may choose the DELAY START option. This will delay the start of the wash cycle by up to 10 hours.

To set DELAY START:

1.Press DELAY START until the desired delay time (in hours) is illuminated.

2.Press START/PAUSE. The countdown to the wash cycle will show in the display window.

10.Press and hold START/PAUSE to begin wash cycle

Press and hold the START/PAUSE button to start the wash cycle. To pause a cycle in progress, press the START/PAUSE button once, then press and hold again to continue the cycle. To cancel a cycle, press the POWER/CANCEL button.

Door Locked

Once you press and hold START/PAUSE, you will hear

the door lock, unlock, and lock again. When the door locked light illuminates, the door is locked. The door is locked

and unlocked automatically, depending on the stage of the wash cycle.

Unlocking the door to add garments:

If you need to open the door to add 1 or 2 missed garments, you may do so while the “Add Clothes” light is lit.

Press START/PAUSE once; the door will unlock once the washer movement has stopped. This may take several minutes. Then close door and press START/PAUSE again to continue the cycle.

To add garments after the “Add Clothes” period is over, the wash cycle needs to be canceled, the items added, and a new

wash cycle started.

11

11. Remove garments promptly after cycle is finished

Promptly remove garments after cycle has completed to avoid odor and rusting of

metal objects on garments. When unloading garments, pull back the door seal and check for small items between the tub and the basket.

If you will be unable to remove the load promptly, use the Fresh Spin™ option to automatically tumble the load periodically for up to 6 hours.

NOTE:

nAfter any wash cycle is completed, the door must be opened and then closed before a new cycle can begin.

nA small amount of water may remain in the dispensers after the wash cycle is complete. This is normal.

nThis washer has a tight seal to avoid water leaks. To avoid odors, leave the door open to allow the washer to dry between uses.

WASHER MAINTENANCE

WASHER CARE

Recommendations to Help Keep Your Washer Clean and Performing at its Best

1.Always use High Efficiency (HE) detergents and follow the HE detergent manufacturer’s instructions regarding the amount of HE detergent to use. Never use more than the recommended amount because that may increase the rate at which detergent and soil residue accumulate inside your washer, which in turn may result in undesirable odor.

2.Use warm or hot water washes sometimes (not exclusively cold water washes), because they do a better job of controlling the rate at which soils and detergent accumulate.

3.Always leave the washer door slightly ajar between uses to help dry out the washer and prevent the buildup of odor-causing residue.

Cleaning Your Front Loading Washer

Read these instructions completely before beginning the routine cleaning processes recommended below. This Washer Maintenance Procedure should be performed, at a minimum, once per month or every 30 wash cycles,

whichever occurs sooner, to control the rate at which soils and detergent may otherwise accumulate in your washer.

Cleaning the Door Seal

1.Open the washer door and remove any clothing or items from the washer.

2.Inspect the seal between the door opening and the drum for stained areas or soil buildup. Pull back the seal to inspect all areas under the seal and to check for foreign objects.

3.If stained areas or soil buildup are found, wipe down these areas of the seal using either of the following two procedures:

a.affresh® Grit Grabber™ Cloth Procedure:

i.When the cycle is complete, gently pull back the rubber door seal and clean the entire surface with the rough side of the Grit Grabber™ cloth.

b.Dilute Liquid Chlorine Bleach Procedure:

i.Mix a dilute bleach solution, using 3/4 cup (177 mL) of liquid chlorine bleach and 1 gallon (3.8 L) of warm tap water.

ii.Wipe the seal area with the dilute solution, using a damp cloth.

iii.Let stand 5 minutes.

iv.Wipe down area thoroughly with a dry cloth and let washer interior air dry with door open.

IMPORTANT:

nWear rubber gloves when cleaning with bleach.

nRefer to the bleach manufacturer’s instructions for proper use.

12

WASHER CARE (cont.)

Cleaning the Inside of the Washer

This washer has a special cycle that uses higher water volumes in combination with affresh® Washer Cleaner or liquid chlorine bleach to thoroughly clean the inside of the washer. Steam washer models also utilize steam to enhance cleaning in this special cycle.

NOTE: Read these instructions completely before beginning the cleaning process.

Begin procedure

1.affresh® Washer Cleaner Cycle Procedure (Recommended):

a.Open the washer door and remove any clothing or items.

b.Add an affresh® Washer Cleaner tablet to the washer drum.

c.Do not add the affresh® Washer Cleaner tablet to the dispenser drawer.

d.Do not add any detergent or other chemical to the washer when following this procedure.

e.Close the washer door.

f.Select the CLEAN WASHER cycle.

g.Press the START button to begin the cycle. The Clean Washer Cycle Operation is described below.

2.Chlorine Bleach Procedure:

a.Open the washer door and remove any clothing or items.

b.Open the dispenser drawer and add 2/3 cup (160 mL) of liquid chlorine bleach to the bleach compartment.

NOTE: Use of more liquid chlorine bleach than is recommended above could cause product damage over time.

c.Close the washer door and the dispenser drawer.

d.Do not add any detergent or other chemical to the washer when following this procedure.

e.Close the washer door.

f.Select the CLEAN WASHER cycle.

g.Press the START button to begin the cycle. The Clean Washer Cycle Operation is described below.

Description of Clean Washer Cycle Operation:

1.The Clean Washer cycle will determine whether clothing or other items are in the washer.

2.If no items are detected in the washer, it will proceed to step 3.

a.If any items are detected in the washer, “rL” (remove load) will be displayed, and the washer “Controls Lock” lights will remain lit. The door will unlock. Open washer and remove any garments from the washer drum.

b.Press PAUSE/CANCEL or POWER/CANCEL to clear the “rL” code.

c.Press START to restart the cycle.

3.After the cycle is complete, leave the door open slightly to allow for better ventilation and drying of the washer interior.

Cancellation of Clean Washer Cycle Operation:

If the Clean Washer cycle is canceled by the user after it has been initiated, it may take up to 30 minutes for the washer to purge any affresh® Cleaner, chlorine bleach, or other chemistry from the wash system and to adequately rinse any

remaining chemistry. The washer door will remain locked until the cancellation process has been completed. This assures no cleaning chemistry will be carried over to the next wash cycle and reduces the potential for damage to subsequent loads of laundry or to the machine itself.

WASHER CARE (cont.)

Clean Washer Cycle Cancellation Procedure:

1.Press the PAUSE/CANCEL or the POWER/CANCEL button on the washer two times.

2.Washer will begin to drain and rinse away the remaining cleaning chemistry.

3.The cycle will complete the cancellation process in approximately 30 minutes or less.

4.The washer then can be used to either repeat the Clean Washer cycle or to wash laundry using one of the regular wash cycles selected by the user.

Cleaning the Outside of the Washer

Use a soft, damp cloth or sponge to wipe up any spills. Occasionally wipe the outside of your washer to help keep it looking new. Use mild soap and water.

IMPORTANT: To avoid damaging the washer’s finish, do not use abrasive products.

CLEANING THE DISPENSER

You may find laundry product residue leftover in your dispenser compartments. To remove residue, follow this recommended cleaning procedure:

1.Pull dispenser drawer out until it stops.

2.Press down on the release lever and pull straight out to remove the dispenser.

3.Remove the insert (the siphon from the softener and bleach compartments).

13

CLEANING THE DISPENSER cont.

4.Wash dispenser and cover panel in warm, soapy water, using a mild detergent.

5.Rinse with warm water.

6.Air dry or wipe with a clean towel. Replace the insert.

7.Align edges of dispenser with guides in washer, then slide dispenser back into slot.

IMPORTANT: Dispenser is not dishwasher safe.

NON-USE AND VACATION CARE

Operate your washer only when you are home. If moving, or not using your washer for a period of time, follow these steps:

1.Unplug or disconnect power to washer.

2.Turn off water supply to washer to avoid flooding due to water pressure surges.

TRANSPORTING YOUR WASHER

1.Shut off both water faucets. Disconnect and drain water inlet hoses.

2.If washer will be moved during freezing weather, follow WINTER STORAGE CARE directions before moving.

3.Disconnect drain hose from drain system and from back of washer.

4.Unplug power cord.

5.Place inlet hoses and drain hose inside washer basket.

6.Bundle power cord with a rubber band or cable tie to keep it from hanging onto the ground.

IMPORTANT: Call for service to install transport bolts. Washer must be moved with transport bolts and in the upright position. To avoid structural damage to your washer, it must be properly set up for relocation by a certified technician.

REINSTALLING/USING WASHER AGAIN

To reinstall washer after non-use, vacation, winter storage, or moving:

1.Refer to Installation Instructions to locate, level, and connect washer.

2.Before using again, run washer through the following recommended procedure:

To use washer again:

1.Flush water pipes and hoses. Reconnect water inlet hoses. Turn on both water faucets.

WINTER STORAGE CARE

IMPORTANT: To avoid damage, install and store washer where it will not freeze. Because some water may stay in hoses, freezing can damage washer. If storing or moving during freezing weather, winterize your washer.

To winterize washer:

1.Shut off both water faucets; disconnect and drain water inlet hoses.

2.Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run washer on RINSE/DRAIN & SPIN cycle for about 30 seconds to mix antifreeze and remaining water.

3.Unplug washer or disconnect power.

IMPORTANT: To reduce risk of hose failure, replace inlet hoses every five years and periodically inspect for kinks, cuts, wear, or water leaks.

HELPFUL TIP: When replacing your inlet hoses, mark replacement date on label with a permanent marker.

2.Plug in washer or reconnect power.

3.Run washer through NORMAL cycle to clean washer and remove antifreeze, if used. Use only HE detergent. Use half the manufacturer’s recommended amount for a medium-size load.

14

TROUBLESHOOTING

15