Performance Recessed CFL Downlighting 1001FDIC
Page 1 of 1 |
|
5" Aperture, 1 Light, Compact Fluorescent, IC AirSeal®, Dimming, Frame-In Kit |
|||||
|
|
3 |
|
Overall Length |
|
|
|
5 |
|
|
|
|
|
|
|
|
|
|
15 5/16" |
|
|
||
|
|
|
|
|
|
||
|
|
|
|
|
12 1/4" |
|
|
1 |
|
|
|
|
|
|
|
|
|
4 |
13" Min. |
|
|
Overall Width |
|
|
|
24" Max. |
|
|
10 3/8" |
|
|
2 |
|
|
|
|
|
|
Frame-in Kit |
|
7 |
|
|
Height: 7 1/4" |
|
|
|
|
|
|
|
|
|
|
|
|
6 |
|
|
Ceiling Opening: 5 1/4" |
|
Reflector Trim |
|
|
|
|
|
Top View |
|
||
|
|
|
|
|
|
||
Complete Fixture consists of Frame-In Kit and Reflector Trim. Select each separately. |
|
|
|||||
Uniframe™ |
Uniframe™ Compact Fluorescent Performance Series Reflector Trims |
||||||
Horizontal Open Horizontal Wall |
Horizontal Wet Location |
Horizontal |
|
||||
Frame-In Kit |
|
||||||
|
|
Wash - Single |
Lensed / Diffused |
Cross Blade |
|
||
1001FDICMX1** |
1001HCL |
1001HCLSW |
Clear Lens |
Fresnel |
1001HACB |
|
|
(Advance Mark10 – 120v) |
1001HCD |
1001HCDSW |
1001HCLC |
1001HCLF |
1001HWHCB |
|
|
26w Triple |
1001HWH |
1001HWHSW |
1001HCDC |
1001HCDF |
|
|
|
GX24q-3 Base |
|
|
|
1001HWHC |
1001HWHF |
|
|
120v – 0.26amp max |
|
|
|
Opal Lens |
|
|
|
1001FDICMX2** |
|
|
|
|
|
|
|
|
|
|
1001HCLO |
|
|
|
|
(Advance Mark10 – 277v) |
|
|
|
1001HCDO |
|
|
|
26w Triple |
|
|
|
1001HWHO |
|
|
|
GX24q-3 Base |
Universal Series Reflector Trims (Reference Trim Spec Sheet for Recommended Lamping) |
||||||
277v – 0.11amp max |
|||||||
|
Cone |
|
|
Satin Cone |
Baffle |
Wall Wash |
Wet Location |
|
1012* |
1071 |
|
1008* |
1005* |
1035 |
1024 |
|
1013* |
1045 |
|
1010* |
1005BNM |
1035WH |
1078 |
|
1013BK* |
1046 |
|
|
1005WH |
1085 |
|
|
1013WH |
1046CD |
|
|
1076 |
1095 |
|
**Add N to catalog number |
1013CD* |
|
|
|
1076WH |
1096 |
*Add NM suffix to catalog number |
for preset nails. |
|
|
|
|
|
1096CD |
for Natural Metal flange and finish. |
Features
1.Housing: .028" (#21ga.) aluminum. UL listed for direct contact with thermal insulation. AirSeal® housing minimizes air leakage to less than 2 CFM at 1.57 PSF (or 75pa), which complies with Model Energy Code (Section 602.3.3) and Washington State Energy Code (Section 502.4) and reduces heat loss and condensation in ceiling. Access door for inspection of junction box.
2.Mounting Frame: .032 (#22 ga.) galvanized steel. Accommodates ceilings up to 1 1/2" thick. 3/8" deep integral lip. Locks into position along length of mounting bars with locking screw and bendable slot. Four slots are positioned 90° apart to simplify alignment. Push-in/twist-out roto-clips hold reflector flush to ceiling.
3.Junction Box: 2" X 4" X 3 1/2" (22 cu. in) .032" (#22 ga.) galvanized steel. UL listed for maximum of 8 (#12 ga.) 90°C through branch circuit conductors.
4.Mounting Bars: .059" (#16 ga.) galvanized steel. Bars pivot for easy attachment and wire-in below ceiling line. Bars extend to accommodate 16" to 24" O.C. joist spacing. Bars can accommodate 12" O.C joist spacing after a slight field modification (see Instruction Sheet). Features integral self tapping phillips screws for secure attachment to wood or metal construction. Attaches to T-bar ceilings without the need of accessories.
5.Ballast: Mounted inside housing. 120V or 277V UL Listed Electronic Dimming Ballast, end of lamp life protection, class “P” thermally protected, class “A” sound rating.
6.Socket: Four-pin base, molded thermoplastic socket, prewired with No. 18 AWM leads to ballast.
7.Socket Housing: .036" (#20ga.) Galvanized Steel housing attaches to reflector trim by spring clip for precise optic alignment.
Lightolier is a Philips group brand
Options & Accessories
Extra-Thick Ceiling
Mounting Ring: 1967B - 1 1/4" to 2" thick ceilings
Labels
cULus Listed (Type I.C., Suitable for Damp Location), I.B.E.W.
Complies with Air Leakage Requirements stated in the Model Energy Code and the Washington State Energy Code.
AirSeal® is a registered trademark of Lightolier
Job Information |
Type: |
|
|
|
|
Job Name:
Cat. No.:
Lamp(s):
Notes:
631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710
We reserve the right to change details of design, materials and finish. www.lightolier.com © 2008 Philips Group • D0708