Lift-Master SOLAR3 User Manual

Size:
472.15 Kb
Download

Solar3 “Robo” InstallationNon-Breakable Solar Panel

MODEL SOLAR3

Solar3 thin film, power modules convert sunlight directly into electricity using advanced thin film technology. The Solar3 is durable, shadow-tolerant,and reliable.

 

WARNING-ELECTRICAL HAZARD This solar electric product

 

is a LIVE power source in sunlight. OBSERVE CAUTION and read instructions.

 

 

 

 

 

 

CORRECT Panel Placement

 

Type 1:

 

 

 

 

Installation must be free of obstructions

 

 

 

 

 

that block sunlight. Install facing SOUTH.

 

Wiring to a Non-Surge

 

 

 

53.78"

Suppressor “Robo”

 

 

 

 

 

Panel should be tilted

 

Use the yellow wires from the J1

 

between 40° and 45°

 

plug. (Polarity does not matter).

 

E

 

Connect the wires from the solar

N

 

South

 

panel to the yellow wires from the

 

 

 

 

 

 

J1 plug on the control board.

 

 

 

Sunlight will energize the battery

 

 

 

through the solar panel.

 

 

 

 

 

 

 

CHECK

 

 

 

 

 

 

 

CHARGINGFUSE

 

 

 

 

 

 

 

POWER BOARD

 

SYSTEM ON

 

 

 

POWER

 

 

 

 

J2

 

 

 

 

 

 

 

 

 

ALARM

REVERSE

 

 

 

 

 

SENSOR

SENSOR

 

 

29.16"

OVERLOAD

HEAVY

 

 

 

 

GATE

 

 

 

INCORRECT

POWER

 

 

 

 

 

 

CLOSE RELAY

 

 

USA

 

 

 

CHARGE OK

 

 

 

 

 

 

 

BATTERY LOW

 

 

 

 

 

 

 

OPEN RELAY

DC

OPERATOR v 5M

 

 

 

 

 

MADE IN

 

 

 

Panel Placement

 

 

 

CENTRAL CONTROL

 

 

 

 

 

FIRE

 

 

 

 

 

 

 

DEPT

 

 

TIMER

UP

PW

 

 

ON

 

60

0

OFF

OPEN TO RIGHT

STRIKE OPEN

SAFETY

LOOP

EXIT

LOOP

RADIO REC

DO NOT install solar panel near trees or buildings that will block the sunlight. To do so will lose charging efficiency.

Polarity Does

Not Matter

10

8

4 2

6

9

7

5

3

 

 

1

 

 

 

Yellow Wires #2, #4

SPECIFICATIONS

Do Not use solar panel and plug-in transformer at the same time.

Type 2:

Wiring to a Surge Suppressor “Robo”

Connect the two wires from the solar panel to the Power Input connection on the surge suppressor (Polarity does not matter). Sunlight will energize the batteries through the solar panel.

Does

 

ACCESS SYSTEMS INC ROBO SURGE SUPPRESSOR

P/N Q412

AC AC

PATENT PENDING

Matter

1 – – 4

5 6

7

8

9 10 11 12 13

 

 

 

 

 

 

 

 

 

 

 

 

 

+

 

 

 

 

 

 

 

CLASS 2

 

 

SAFETY

EXIT

FIRE DEPT

STRIKE OPEN

RADIO SUPPLY

 

 

LOOP

LOOP

KEY SWITCH PUSH BUTTON

RECEIVER

Electric Ratings at 1000 W/m2, AM1.5, Cell Temp. 25C

Max Power:

64

W

Current Max Power:

3.88 A

Voltage Max Power:

16.5 V

Short Circuit Current:

4.8

A

Open Circuit Voltage:

23.8 V

Model Type:

US-64

Max System Voltage:

600 V

Series Fuse:

8.0

 

Min. Blocking/Bypass Diode: A

 

Field Wiring:

8.0

A

Copper only, 18-10AWG

Insulated for 90C Min.

During initial 8-10weeks of operation, the module has higher electrical output than rated output. The output power may be higher by 15%, the operating voltage may be higher by 11% and operating current may be higher by 4%.

MAINTENANCE: Solar modules require little maintenance. It is not uncommon for a remote site to be checked once a year. Under most conditions, normal rainfall is sufficient to keep the power modules clean. If dirt build-upbecomes excessive, clean the solar panel with a soft cloth, mild detergent and water. Modules that are mounted flat (0° tilt angle) should be cleaned more often as they will not "self clean" as effectively as modules mounted at 15° tilt or greater. Once a year, check the general condition of the wiring and connections. Also, check to be sure that mounting hardware is tight. Loose bolts could result in a damaged module or array.

®

© 2005 The Chamberlain Group, Inc.

All Rights Reserved

For Technical Support: 1-800-528-2806

Solar3 “Miracle-One™”InstallationNon-Breakable Solar Panel

Refer to other side for panel: dimensions, specifications, correct placement and maintenance.

Solar3 thin film, power modules convert sunlight directly into electricity using advanced thin film technology. The Solar3 is durable, shadow-tolerant,and reliable.

WARNING-ELECTRICAL HAZARD This solar electric product

is a LIVE power source in sunlight. OBSERVE CAUTION and read instructions.

DC Power Adapter (Purchased separately) needed for solar panel connection to the Miracle-One™.

Solar Panel Wires

DC Power Adapter

Part # ASOLARADP

Battery Connector

Miracle-One™

Connector from

Miracle-One™J1 Plug

Don’t use solar panelplug-intransformer

same time. contact technical for this type of

power connection. doc. # 01-51266

DC Power

Adapter

fits inside the Miracle-One™electronic box

LAKE FOREST, CALIFORNIA

www.eliteaccess.com

8

REV A

BLUE

GREEN

BLACK

WHITE

RED

BROWN

BLUE

GREEN

BURGLAR

ALARM INPUT

 

UL SENSOR

5

6

7

8

9

10

11

12

13

14

15

16

 

LOOP

 

 

 

 

17

18

19

20

21

22

A plug-insolar power adapter (Sold separately) can be use as a “power option” for theMiracle-One™.Simply plug in the adapter to the existing electronic control box. No other modifications are necessary. The solar panel provides solar power for theMiracle-One™single and double arm operators.

 

 

 

 

®

 

 

 

 

01-50743B

© 2005 The Chamberlain Group, Inc.

 

 

 

 

All Rights Reserved

For Technical Support: 1-800-528-2806

 

 

 

 

845 Larch Avenue Elmhurst, Illinois 60126

www.chamberlain.com