Lift-Master 61LM User Manual

Size:
202.18 Kb
Download

Figure 1

Model 61LM Model 62LM Model 63LM

 

(+) (0)

(–)

Push Buttons

Push Buttons

Locating your code switches

Single-ButtonRemote Control:

Slide the battery compartment cover back to access the code switches in the remote control (Figure 2).

2-ButtonRemote Control:

The 2-buttonremote control has two push buttons (for button 1 and button 2), each activated by its own set of code switches. One of the buttons can be used to operate a garage door opener. The other button can operate an entry way, light product or another door opener.

Access the code switches for button 1 (smooth button) by sliding back the battery compartment cover. To access the code switches for button 2 (ribbed button), remove the battery compartment cover and the cover screw.

Then depress the tab in the edge of the case (alongside the battery). The remote control case back will lift off

(Figure 2).

3-ButtonRemote Control:

The 3-buttonremote control has three buttons. The large button is recommended for use with a garage door opener. The other push buttons can be used to operate another garage door opener and/or light control product.

Slide back the battery compartment cover to access the code switches in the 3-buttonremote control

(Figure 2).

To match or change the code in the remote control

Locate the code switches in both the new and the original remote controls, either by removing the case screw and cover or by sliding the battery compartment cover back. Place remote controls side by side as shown (Figure 3) and set switches in all remote controls to matching positions(+,0,-).Use a pen or screwdriver to slide the code switches.

NOTE: Code switch #1 on thethree-buttonremote control is dormant, when used with asingle-buttonremote control. Set code switch #1, in thesingle-buttonremote control, to match the push button selected on thethree-buttonremote control (Figure 1).

Single-ButtonRemote Control

Model 61LM

2-ButtonRemote Control

Model 62LM

3-ButtonRemote Control

Model 63LM

WARNING

To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:

ALWAYS keep remote controls out of reach of children.

NEVER permit children to operate, or play with remote controls.

Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.

ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.

Figure 2

Model 61LM

Model 62LM

 

 

Single-ButtonRemote Control

2-ButtonRemote Control

0 –

+

 

 

 

 

1

 

0 –

+

0 –

+

2

 

1

 

1

 

 

 

 

 

 

3

 

2

 

2

 

 

 

 

 

 

4

 

3

 

3

 

 

 

 

 

 

5

 

4

 

4

 

6

 

5

 

5

 

 

 

6

 

6

 

7

 

 

 

 

 

8

 

7

 

7

 

 

 

 

 

 

9

 

8

 

8

 

 

 

9

 

9

 

Code switches (1-9)Code switches (1-9)

Model 63LM

3-ButtonRemote Control

0

+

1

 

 

2

 

 

3

 

 

4

 

 

5

 

 

6

 

 

7

 

 

8

 

 

9

 

 

Code switches (1-9)(Code switch #1 is dormant.)

Figure 3

0

+

0

+

1

 

 

1

 

 

2

 

 

2

 

 

3

 

 

3

 

 

4

 

 

4

 

 

5

 

 

5

 

 

6

 

 

6

 

 

7

 

 

7

 

 

8

 

 

8

 

 

9

 

 

9

 

 

Match code switches (1-9)between old remote control and new remote control

 

 

 

 

 

 

0

+

0

+

0

+

1

 

 

1

 

 

1

 

 

2

 

 

2

 

 

2

 

 

3

 

 

3

 

 

3

 

 

4

 

 

4

 

 

4

 

 

5

 

 

5

 

 

5

 

 

6

 

 

6

 

 

6

 

 

7

 

 

7

 

 

7

 

 

8

 

 

8

 

 

8

 

 

9

 

 

9

 

 

9

 

 

 

 

 

Match code switches (1-9)

Match code switches (2-9)

between old remote control

between old remote control and

and new remote control

new remote control

Programming the opener

RED-1

WHT-2

 

+

 

 

 

 

H

0

 

I

 

G

 

 

H

12 3 4 5 6 7 8 9

N O R M

O R

RED-1WHT-2

H

I

G

H

N O R M

Replacing the remote control battery

WARNING

To prevent possible SERIOUS INJURY or DEATH:

NEVER allow small children near batteries.

If battery is swallowed, immediately notify doctor.

Locate the battery by sliding the battery compartment cover.

Dispose of old batteries properly.

If your unit has a “Learn” button:

1.Press and release the “learn” button located on the back panel of the motor unit. The learn indicator light will glow steadily for 30 seconds.

2.Within the 30 second window, press and hold the button on the hand-heldremote.

3.The unit will either activate or the opener light bulb will blink signifying it has learned the code.

H

I

G

H

NOR

If your unit has code switches:

1. Using a step ladder climb up to the back

 

 

 

 

 

 

 

 

 

 

 

of your motor unit. Check the code

 

 

 

 

 

 

 

 

 

 

 

switch settings on the back of the motor

+

 

 

 

 

 

 

 

 

 

 

unit.

 

 

 

 

 

 

 

 

 

 

H

 

 

 

 

 

 

 

 

 

 

H

 

0

 

 

 

 

 

 

 

 

 

I

 

 

 

 

 

 

 

 

 

 

 

G

 

 

 

 

 

 

 

 

 

 

N

2. Use a pen or screw driver to set the

1

2

3

4

5

 

6

 

7

8

9

 

 

 

 

 

 

 

 

 

 

 

code switches on the back of the

 

 

 

 

 

 

 

 

 

 

 

remote control to match the code

 

 

 

 

 

 

 

 

 

 

 

 

+

 

 

 

 

 

 

 

 

 

 

 

0

 

 

 

 

 

 

 

 

 

switches on the back of the motor unit.

 

1

2

3

4

5

6

7

8

9

 

 

 

 

 

 

 

 

 

 

 

 

3. Once the code switches have been set

 

 

 

 

 

 

 

 

 

 

 

push the remote control button to activate your unit.

 

 

NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or remote control are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

 

© 2006 The Chamberlain Group, Inc.

114A1224F

All Rights Reserved