Lift-Master 2500 User Manual

Size:
2.54 Mb
Download

The Chamberlain Group, Inc. 845 Larch Avenue

Elmhurst, Illinois 60126-1196www.liftmaster.com

®

GARAGE DOOR OPENER

Model 2500

For Residential Use Only

Owner’s Manual

Please read this manual and the enclosed safety materials carefully!

Fasten the manual near the garage door after installation.

The door WILL NOT CLOSE unless the Protector System® is connected and properly aligned.

Periodic checks of the opener are required to ensure safe operation.

The model number label is located on the front of your opener.

TABLE OF CONTENTS

 

Introduction

2-5

Safety symbol review and signal word review ............

2

Preparing your garage door ........................................

3

Tools ............................................................................

3

Planning .....................................................................

4

Carton inventory ..........................................................

5

Hardware inventory .....................................................

5

Assembly

6-7

Fasten rail to the motor unit ........................................

6

Set the belt tension .....................................................

6

Attach the belt cap retainer .........................................

7

Installation

7-23

Installation safety instructions .....................................

7

Determine the header bracket location....................

8-9

Install the header bracket..........................................

10

Attach the rail to the header bracket .........................

11

Position the opener ...................................................

12

Hang the opener .......................................................

13

Install the door control...............................................

14

Install the lights and lens...........................................

15

Attach the emergency release rope and handle

.......15

Electrical requirements..............................................

16

Install the Protector System®................................

17-19

Fasten the door bracket.......................................

20-21

Connect the door arm to the trolley .....................

22-23

Adjustment

24-26

Program the travel limits ...........................................

24

Adjust the force .........................................................

25

Test the safety reversal system.................................

26

Test the Protector System®........................................

26

Operation

27-30

Operation safety instructions.....................................

27

Using your garage door opener ................................

27

Using the door control ...............................................

28

To open the door manually........................................

28

Care of your garage door opener..............................

29

Having a problem?...............................................

29-30

Programming

31-32

To add a hand-heldremote control ...........................

31

To erase all codes .....................................................

31

3-Channelremotes....................................................

31

To add or change a Keyless Entry PIN.....................

32

Repair Parts

33-34

Rail assembly parts...................................................

33

Installation parts ........................................................

33

Motor unit assembly parts .........................................

34

Accessories

35

Repair Parts and Service

36

Warranty

36

INTRODUCTION

Safety Symbol Review

This garage door opener has been designed and tested to offer safe service provided it is installed, operated, maintained and tested in strict accordance with the instructions and warnings contained in this manual.

WARNING

Mechanical

WARNING

Electrical

CAUTION

When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury or death if you do not comply with the warnings that accompany them. The hazard may come from something mechanical or from electric shock. Read the warnings carefully.

When you see this Signal Word on the following pages, it will alert you to the possibility of damage to your garage door and/or the garage door opener if you do not comply with the cautionary statements that accompany it. Read them carefully.

2

Preparing your garage door

Before you begin:

Disable locks.

Remove any ropes connected to garage door.

Complete the following test to make sure your garage door is balanced and is not sticking or binding:

1.Lift the door about halfway as shown. Release the door. If balanced, it should stay in place, supported entirely by its springs.

2.Raise and lower the door to see if there is any binding or sticking.

If your door binds, sticks, or is out of balance, call a trained door systems technician.

Sectional Door

One-PieceDoor

WARNING

To prevent possible SERIOUS INJURY OR DEATH:

ALWAYS call a trained door systems technician if garage door binds, sticks, or is out of balance. An unbalanced garage door may not reverse when required.

NEVER try to loosen, move or adjust garage door, door springs, cables, pulleys, brackets or their hardware, all of which are under EXTREME tension.

Disable ALL locks and remove ALL ropes connected to garage door BEFORE installing and operating garage door opener to avoid entanglement.

CAUTION

To prevent damage to garage door and opener:

ALWAYS disable locks BEFORE installing and operating the opener.

ONLY operate garage door opener at 120V, 60 Hz to avoid malfunction and damage.

Tools needed

During assembly, installation and adjustment of the opener, instructions will call for hand tools as illustrated below.

Carpenter's

Level

Pencil

1

2

Hack Saw

Tape Measure

Wire Cutters

 

Drill

3/16", 5/16" and

 

Claw Hammer

 

 

5/32" Drill Bits

 

Pliers

 

 

 

 

Stepladder

1/2" and 7/16" Sockets

Screwdriver

 

and Wrench

 

Adjustable End Wrench

 

 

 

3

Planning

Identify the type and height of your garage door. Survey your garage area to see if any of the conditions below apply to your installation. Additional materials may be required. You may find it helpful to refer back to this page as you proceed with the installation of your opener.

SECTIONAL DOOR INSTALLATION

FINISHED CEILING

 

 

Support bracket &

 

fastening hardware

Horizontal and vertical reinforcement

is required.

is needed for lightweight garage doors

See page 13

(fiberglass, steel, aluminum, door with

 

glass panels, etc.). See page 20 for details.

Rail

Header Wall

Motor unit

 

 

Extension Spring

 

OR Torsion Spring

Wall-mounted

Access Door Door Control

— —

Door

Center

— — —

 

— —

 

Safety

Reversing

Sensor

Gap between floor

Safety and bottom of door must not exceed 1/4".

Reversing Sensor

ONE-PIECEDOOR WITHOUT TRACK

Header Wall

 

Gap between floor

Safety Reversing Sensor

and bottom of door

must not exceed 1/4".

FINISHED CEILING

 

Support bracket &

Motor unit

fastening hardware

is required. See page 13

 

Rail

Wall-mounted

Door Control

Access Door

Safety

Reversing

Sensor

ONE-PIECEDOOR WITH TRACK

Safety

Reversing Sensor

Gap between floor and bottom of door must not exceed 1/4".

Access

Door

Safety

Reversing

Sensor

4

Carton Inventory

Your garage door opener is packaged in two cartons which contain the motor unit and the parts illustrated below. Note that accessories will depend on the

model purchased. If anything is missing, carefully check the packing material. Parts may be stuck in the foam. KEEP THE FOAM INTACT (see page 6.)

LOCK

LIGHT

Multi-Function

Door Control Panel

Model 79LM

 

NLY

 

T O

 

UN

G

MO

ILIN

 

CE

 

 

UP

Remote Control

Transmitter Visor Clip

SECURITY

Belt Cap Retainer

3-ChannelRemote Control

Styrofoam

2-ConductorBell Wire

Light Lens

White & White/Red

 

Header Bracket

One-Piece

T-rail

Door Bracket

Curved Door

Arm Section

Trolley

Belt

Pulley Bracket

Safety Sensor

Bracket (2)

Belt

(2) Safety Reversing Sensors

(1 Sending Eye and 1 Receiving Eye) with 2-ConductorWhite & White/Black Bell Wire attached

Straight Door Safety Labels Arm Section and

Literature

Hardware Inventory

INSTALLATION HARDWARE

Lock Washer 5/16" (4)

Hex Screw #8 x 3/8" (3)

Screw 6AB x 1-1/4"(2)

Hex Bolt 5/16"-18x 7/8" (4)

Screw 6-32x 1" (2)

Lag Screw 5/16"-9x1-5/8"(2)

Insulated Staples (30)

Lag Screw 5/16"-18x1-7/8"(2)

Ring Fastener (3)

Self-ThreadingScrew1/4"-14x5/8"(2)

Handle

Clevis Pin 5/16" x 2-3/4"(1)

Dry Wall Anchors (2)

Clevis Pin 5/16" x 1-1/4"(1)

Rope

Clevis Pin 5/16" x 1" (1)

Carriage Bolts 1/4" - 20 x 1/2" (2)

Nut 5/16" - 18 (4)

Wing Nut 1/4” x 20 (2)

5

ASSEMBLY STEP 1

Attach the T-Railto the Motor Unit

To avoid installation difficulties, do not run the garage door opener until instructed to do so.

Remove the two washered bolts mounted in top of motor unit.

Align T-railand styrofoam over sprocket. Cut tape fromT-rail,belt and styrofoam.

REMOVE STYROFOAM.

Insert both washered bolts through the T-railinto the motor unit. Tighten bolts securely.

Use only these bolts! Use of any other bolts will cause serious damage to door opener.

Position belt over the motor unit sprocket.

CAUTION

To avoid serious damage to opener, ONLY use bolts mounted in top of motor unit.

Washered Bolts

Motor Unit

Sprocket

Foam Packaging

ASSEMBLY STEP 2

Set the Belt Tension

By hand, thread the spring trolley nut on the threaded shaft until it is finger tight against the trolley (Figure 1). Do not use any tools.

Insert a screwdriver tip into one of the nut ring slots and brace it firmly against the trolley (Figure 2).

Figure 1

Trolley

Trolley

Threaded

Shaft

Spring

Trolley Nut

Figure 2

 

Trolley

 

Threaded

 

 

 

Nut

Shaft

 

 

 

Ring

 

Square End

 

 

 

 

Nut Ring

 

 

Slots

Trolley

 

 

Place a 7/16" open end wrench on the square end. Rotate about 1/4 turn until the spring releases

and snaps the nut ring against the trolley (Figure 3).

This extends the spring for optimum belt tension.

Figure 3

Trolley

Nut Ring

Trolley

Nut Ring

 

BEFORE

 

AFTER RELEASE

 

1"

 

1-1/4"

6

ASSEMBLY STEP 3

Attach the Belt Cap Retainer

Position the belt cap retainer over the opener sprocket so the two holes in cap align with the two holes in mounting plate. Attach with #8x3/8" hex screws provided.

You have now finished assembling your garage door opener. Please read the following warnings before proceeding to the installation section.

HARDWARE SHOWN ACTUAL SIZE

Hex Screw

#8x3/8"

WARNING

To avoid possible SERIOUS INJURY to fingers from moving garage door opener:

ALWAYS keep hand clear of sprocket while operating opener.

Securely attach sprocket cover BEFORE operating.

Hex Screws

#8x3/8"

Belt Cap

Retainer

Opener Sprocket

Mounting Plate

INSTALLATION

IMPORTANT INSTALLATION INSTRUCTIONS

WARNING

To reduce the risk of severe injury or death:

1.READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCTIONS.

2.Install garage door opener only on properly balanced and lubricated garage door. An improperly balanced door may not reverse when required and could result in SEVERE INJURY or DEATH.

3.All repairs to cables, spring assemblies and other hardware MUST be made by a trained door systems technician BEFORE installing opener.

4.Disable all locks and remove all ropes connected to garage door BEFORE installing opener to avoid entanglement.

5.Install garage door opener 7 feet or more above floor.

6.Mount emergency release handle 6 feet above floor.

7.NEVER connect garage door opener to power source until instructed to do so.

8.NEVER wear watches, rings or loose clothing while installing or servicing opener. They could be caught in garage door or opener mechanisms.

9.Install wall-mountedgarage door control:

within sight of the garage door

out of reach of children at minimum height of 5 feet

away from all moving parts of the door.

10.Place entrapment warning label on wall next to garage door control.

11.Place manual release/safety reverse test label in plain view on inside of garage door.

12.Upon completion of installation, test safety reversal system. Door MUST reverse on contact with a oneinch high object (or a 2x4 laid flat) on the floor.

7

INSTALLATION STEP 1

Determine the Header Bracket

Location

WARNING

To prevent possible SERIOUS INJURY or DEATH:

Header bracket MUST be RIGIDLY fastened to structural support on header wall or ceiling, otherwise garage door might not reverse when required. DO NOT install header bracket over drywall.

Concrete anchors MUST be used if mounting header bracket or 2x4 into masonry.

NEVER try to loosen, move or adjust garage door, springs, cables, pulleys, brackets, or their hardware, all of which are under EXTREME tension.

ALWAYS call a trained door systems technician if garage door binds, sticks, or is out of balance. An unbalanced garage door might not reverse when required.

Vertical

 

Finished

Centerline

 

Ceiling

Header

2x4

Structural

Wall

 

 

 

Supports

Vertical

Centerline

Installation procedures vary according to garage door types. Follow the instructions which apply to your door.

SECTIONAL DOOR

AND ONE-PIECEDOOR WITH TRACK

1.Close the door and mark the inside vertical centerline of the garage door.

2.Extend the line onto the header wall above the door.

You can fasten the header bracket within 4 feet of the left or right of the door center only if a torsion spring or center bearing plate is in the way; or you can attach it to the ceiling (see page 10) when clearance is minimal. (It may be mounted on the wall upside down if necessary, to gain approximately 1/2".)

If you need to install the header bracket on a 2x4 (on wall or ceiling), use lag screws (not provided) to securely fasten the 2x4 to structural supports as shown here and on page 10.

3.Open your door to the highest point of travel as shown. Draw an intersecting horizontal line on the header wall 2" above the high point. This height will provide travel clearance for the top edge of the door.

Proceed to Step 2, page 10.

 

Ceiling

 

Header Wall

 

 

2"

Track

 

Highest Point

 

 

of Travel

Sectional door

 

 

 

 

with curved

 

 

track

 

Door

 

 

 

Header Wall

 

 

Track

 

 

2"

One-piece

 

Highest Point

 

of Travel

door with

 

Door

 

horizontal

 

 

 

track

 

 

8

ONE-PIECEDOOR WITHOUT TRACK

1.Close the door and mark the inside vertical centerline of your garage door. Extend the line onto the header wall above door, as shown.

If headroom clearance is minimal, you can install the header bracket on the ceiling. See page 10.

If you need to install the header bracket on a 2x4 (on wall or ceiling), use lag screws (not provided) to securely fasten the 2x4 to structural supports as shown. If installing into masonry, use concrete anchors (not provided).

2.Open your door to the highest point of travel as shown. Measure the distance from the top of the door to the floor. Subtract the actual height of the door. Add 8" to the remainder. (See Example).

3.Close the door and draw an intersecting horizontal line on the header wall at the determined height.

NOTE: If the total number of inches exceeds the height available in your garage, use the maximum height possible, or refer to page 10 for ceiling installation.

EXAMPLE

 

 

Distance from top of door

 

 

(at highest point of travel) to floor ......................

92"

Actual height of door ..........................................

-88"

 

 

 

Remainder..........................................................

4"

Add.....................................................................

 

+8"

Bracket height on header wall............................

=12"

(Measure UP from top of CLOSED door.)

 

 

Proceed to Step 2, page 10.

Unfinished

Ceiling

 

Structural

Header Wall

Supports

Vertical

 

 

Centerline

 

2x4

 

2x4

 

OPTIONAL

 

CEILING MOUNT

 

FOR

 

HEADER BRACKET

 

Vertical

 

Centerline

 

of Garage

 

Door

 

Header Wall

 

Highest Point

 

of Travel

Door

 

Jamb

Distance

Hardware

 

 

Floor

One-piecedoor without track: jamb hardware

 

Highest Point

 

of Travel

 

Header Wall

Door

Distance

 

 

Pivot

 

Floor

One-piecedoor without track: pivot hardware

9

INSTALLATION STEP 2

Install the Header Bracket

You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry, use concrete anchors (not provided).

WALL HEADER BRACKET INSTALLATION

Center the bracket on the vertical centerline with the bottom edge of the bracket on the horizontal line as shown (with the arrow pointing toward the ceiling).

Mark the vertical set of bracket holes (do not use the holes designated for ceiling mount). Drill 3/16" pilot holes and fasten the bracket securely to a structural support with the hardware provided.

HARDWARE SHOWN ACTUAL SIZE

Lag Screw 5/16"-9x1-5/8"

CEILING HEADER BRACKET INSTALLATION

Extend the vertical centerline onto the ceiling as shown.

Center the bracket on the vertical mark, no more than 6" from the wall. Make sure the arrow is pointing toward the wall. The bracket can be mounted flush against the ceiling when clearance is minimal.

Mark the side holes. Drill 3/16" pilot holes and fasten bracket securely to a structural support with the hardware provided.

Ceiling Mounting Holes

CEILING MOUNT ONLY

UP

The nail hole is for positioning only.

You must use lag screws

to mount the header bracket.

Wall Mounting Holes

CEILING MOUNT ONLY

UP

Optional

Wall Mounting Holes

Header

 

 

Wall

G M

LY

 

NT

ON

 

OU

 

 

ILIN

 

 

CE

 

 

UP

 

2x4

Header

 

Structural

Bracket

 

Support

 

 

Highest Point of

Garage Door Travel

The nail hole is for positioning only.

You must use lag screws

to mount the header bracket.

Vertical

Centerline

Lag Screws 5/16"-9x1-5/8"

Door Spring

Garage

Door

Vertical

Centerline

– Finished Ceiling –

Header

Vertical Centerline

Bracket

 

PU

 

6" Maximum

Door

Spring Lag Screws

5/16"-9x1-5/8"

Header Wall

Garage Door

Vertical

Centerline

10

Header Wall

Header Bracket

Belt Pulley Bracket

Torsion

Spring

T-Rail

Garage

Door

Foam Packaging

INSTALLATION STEP 3

Attach the T-Railto the Header Bracket

Position the opener on the garage floor below the header bracket. Use packing material as a protective base. NOTE: If the door spring is in the way you’ll need help. Have someone hold the opener securely on a temporary support to allow the rail to clear the spring.

Position the rail bracket against the header bracket.

Align the bracket holes and join with a clevis pin as shown.

Insert a ring fastener to secure.

Ring Fastener

Header Bracket

Clevis Pin

5/16"x2-3/4"

Belt Pulley Bracket

T-Rail

Opener Carton or

Temporary

Support

HARDWARE SHOWN ACTUAL SIZE

Clevis Pin

 

5/16" x 2-3/4"

Ring Fastener

11

INSTALLATION STEP 4

Position the Opener

Follow instructions which apply to your door type as illustrated.

SECTIONAL DOOR OR ONE-PIECEDOOR WITH TRACK

A 2x4 laid flat is convenient for setting an ideal door- to-raildistance.

Raise the opener onto a stepladder. You will need help at this point if the ladder is not tall enough.

Open the door all the way and place a 2x4 laid flat on the top section beneath the rail.

If the top panel hits the trolley when you raise the door, pull down on the trolley release arm to disconnect inner and outer sections. Slide the

outer trolley toward the motor unit. The trolley can remain disconnected until Step 12 is completed.

Trolley

Release Arm

Trolley

CAUTION

To prevent damage to garage door, rest garage door opener rail on 2x4 placed on top section of door.

 

2x4

T-rail

laid flat

Door

ONE-PIECEDOOR WITHOUT TRACK

With the door fully open and parallel to the floor, measure the distance from the floor to the top of the door.

Using a stepladder as a support, raise the opener to this height.

The top of the door should be level with the top of the motor unit. Do not position the opener more than 2" above this point.

Header

Bracket

Top of Motor Unit

Top of Door

12

INSTALLATION STEP 5

Hang the Opener

Three representative installations are shown. Yours may be different. Hanging brackets should be angled, Figure 1, to provide rigid support. On finished ceilings, Figure 2, attach a sturdy metal bracket to structural supports before installing the opener. This bracket and fastening hardware are not provided.

Existing brackets from a previous installation may be fastened to the sides of the motor unit as in Figures 1 and 2, or to the mounting tabs as shown in

Figure 3. Then continue with step 5 below.

1.Remove from packaging. Measure the distance from each side of the motor unit to the structural support.

2.Cut both pieces of the hanging bracket to required lengths.

3.Drill 3/16" pilot holes in the structural supports.

4.Attach one end of each bracket to a support with 5/16"-18x1-7/8"lag screws.

5.Fasten the opener to the hanging brackets with 5/16"-18x7/8"hex bolts, lock washers and nuts.

6.Check to make sure the rail is centered over the door (or in line with the header bracket if the bracket is not centered above the door).

7.Remove the 2x4. Operate the door manually. If the door hits the rail, raise the header bracket.

8.Grease the top and underside of the rail surface where the trolley slides with

rail grease.

HARDWARE SHOWN ACTUAL SIZE

Lag Screw 5/16"-18x1-7/8"

Hex Bolt

 

 

5/16"-18x7/8"

Nut 5/16"-18

Lock Washer 5/16"

WARNING

To avoid possible SERIOUS INJURY from a falling garage door opener, fasten it SECURELY to structural supports of the garage. Concrete anchors MUST be used if installing any brackets into masonry.

Figure 1

Structural

Supports

Lag Screws 5/16"- 18x1-7/8"

Measure

Distance

Hex Bolts 5/16"-18x7/8"

Lock Washers 5/16" Nuts 5/16"-18

Preferred range of bracket placement

Figure 2

 

— FINISHED CEILING —

Hidden

 

Support

 

 

Lag Screws

 

5/16"-18x1-7/8"

Bracket

(Not Provided)

Hex Bolts

(Not Provided)

5/16"-18x7/8"

 

 

Lock Washers 5/16"

 

Nuts 5/16"-18

Hex Bolts

 

5/16"-18x7/8"

 

Lock Washers 5/16"

 

Nuts 5/16"-18

 

Preferred range of bracket placement

Figure 3

Existing Brackets

Bracket (Provided)

Utilizing existing top mount installation

13

INSTALLATION STEP 6

Install the Door Control

Locate door control within sight of the door at a minimum height of 5 feet where small children cannot reach, and away from moving parts of the door and door hardware. The installation surface must be smooth and flat. If installing into drywall (Figure 1), drill 5/32" holes and use anchors provided. For prewired installations (as in new home construction), it may be mounted to a single gang box (Figure 2).

NOTE: After installation, a green or amber indicator light behind the cover will indicate proper connection. If not lit, the Lock and Light features will not function (reverse wires to correct).

1.Strip 7/16" of insulation from one end of bell wire and connect to the two screw terminals on back of door control by color: white wire to WHT and white/red wire to the RED (Figure 3).

2.Remove white cover by gently prying on a side corner near the top of the cover with a small flat head screwdriver (Figure 4). Fasten with 6ABx1-1/4"self-tappingscrews (drywall installation) or6-32x1"machine screws (into gang box) as follows:

Drill and install bottom screw, allowing 1/8" to protrude above wall surface.

Position bottom of door control on screw head and slide down to secure. Adjust screw for snug fit.

Install top screw with care to avoid cracking plastic housing. Do not overtighten.

Insert bottom tabs and snap on cover. (To remove cover after mounting, gently pry on a side corner near the top of the white cover with paper clip or small flat head screwdriver.)

NOTE: The push bar may stick if the door control is not mounted on a smooth surface. If a click is not heard when pressing the push bar, loosen the two mounting screws or relocate the door control to a smoother surface.

3.(Standard installation only) Run bell wire up wall and across ceiling to motor unit. Use insulated staples to secure wire in several places. Do not pierce wire with a staple, creating a short or open circuit.

4.Strip 7/16" of insulation from end of bell wire. Connect bell wire to the quick-connectterminals as follows: white to white and white/red to red (Figure 5).

5.Use tacks or staples to permanently attach entrapment warning label to wall near door control,

and manual release/safety reverse test label in a prominent location on inside of garage door.

NOTE: DO NOT connect the power and

operate the opener at this time. The trolley will travel to the full open position but will not return

to the close position until the sensor beam is connected and properly aligned. See Safety Reversing Sensor Instructions beginning on page 17.

WARNING

To prevent possible SERIOUS INJURY or DEATH from electrocution:

Be sure power is not connected BEFORE installing door control.

Connect ONLY to 24 VOLT low voltage wires.

To prevent possible SERIOUS INJURY or DEATH from a closing garage door:

Install door control within sight of garage door, out of reach of children at a minimum height of 5 feet, and away from all moving parts of door.

NEVER permit children to operate or play with door control push buttons or remote control transmitters.

Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.

ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door.

HARDWARE SHOWN ACTUAL SIZE

Screw 6AB x 1-1/4"

 

Insulated

(drywall installation)

 

Staples

Screw 6-32x 1"

 

 

(gang box installation)

Dry Wall Anchors

STANDARD

Figure 2

PRE-WIRED

Figure 1 INSTALLATION

INSTALLATION

Single

Gang Box

LOCK

 

 

LIGHT

LOCK

 

 

 

To Replace

LIGHT

 

 

24 Volt

Insert Bottom Tabs First

To Replace

Bell Wire

 

Insert Bottom Tabs First

 

 

Figure 3 MULTI-FUNCTION

Figure 4 REMOVE COVER

DOOR CONTROL (BACK)

 

Top Mounting Hole

 

 

Terminal

 

 

Screws

 

 

Bell Wire

 

LOCK

 

LIGHT

Bottom Mounting Hole

Figure 5

To release wire, push in tab with screwdriver tip

7/16"

Red

Strip wire 7/16"

Door Control

Connections

White Grey

14

INSTALLATION STEP 7

Install the Lights and Lens

Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is in the fully open position. Do not remove the lens.

Install up to a 100 watt maximum light bulb in each socket. The lights will turn ON and remain lit for approximately 4-1/2minutes when power is connected. Then the lights will turn OFF.

Reverse the procedure to close the lens.

If the bulbs burn out prematurely due to vibration, replace with a Garage Door Opener bulb.

NOTE: Use only standard light bulbs. The use of short neck or speciality light bulbs may overheat the endpanel or light socket.

Release Tab

Lens

Lens Hinge

Release

Tab Slot

Lens Hinge Slots

Release Tab

Release

Tab Slot

INSTALLATION STEP 8

Attach the Emergency Release

Rope and Handle

Thread one end of the rope through the hole in the top of the red handle so "NOTICE" reads right side up as shown. Secure with an overhand knot at least 1" from the end of the rope to prevent slipping.

Thread the other end of the rope through the hole in the release arm of the outer trolley.

Adjust rope length so the handle is 6 feet above the floor. Secure with an overhand knot.

NOTE: If it is necessary to cut the rope, heat seal the cut end with a match or lighter to prevent unraveling.

WARNING

To prevent possible SERIOUS INJURY or DEATH from a falling garage door:

If possible, use emergency release handle to disengage trolley ONLY when garage door is CLOSED. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly.

NEVER use emergency release handle unless garage doorway is clear of persons and obstructions.

NEVER use handle to pull door open or closed. If rope knot becomes untied, you could fall.

Trolley

Rope

NOTICE

Overhand

Knot

Overhand

Knot

Trolley

Release Arm

Emergency

Release Handle

15

INSTALLATION STEP 9

Electrical Requirements

To avoid installation difficulties, do not run the opener at this time.

To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you have, contact a qualified electrician to install the proper outlet.

WARNING

To prevent possible SERIOUS INJURY or DEATH from electrocution or fire:

Be sure power is not connected to the opener, and disconnect power to circuit BEFORE removing cover to establish permanent wiring connection.

Garage door installation and wiring MUST be in compliance with all local electrical and building codes.

NEVER use an extension cord, 2-wireadapter, or change plug in any way to make it fit outlet. Be sure the opener is grounded.

RIGHT

WRONG

If permanent wiring is required by your local code, refer to the following procedure.

To make a permanent connection through the 7/8" hole in the top of the motor unit (according to local code):

Remove the motor unit cover screws and set the cover aside.

Remove the attached 3-prongcord.

Connect the black (line) wire to the screw on the brass terminal; the white (neutral) wire to the screw on the silver terminal; and the ground wire to the green ground screw. The opener must be grounded.

Reinstall the cover.

To avoid installation difficulties, do not run the opener at this time.

PERMANENT WIRING

CONNECTION

Ground Tab

Green

Ground Screw

Ground Wire

Black

Wire

White Wire

Black Wire

16

INSTALLATION STEP 10

Install the Protector System®

The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. This is a required safety device and cannot be disabled.

IMPORTANT INFORMATION ABOUT THE SAFETY REVERSING SENSOR

When properly connected and aligned, the safety reversing sensor will detect an obstacle in the path of its electronic beam. The sending eye (with an orange indicator light) transmits an invisible light beam to the receiving eye (with a green indicator light). If an obstruction breaks the light beam while the door is closing, the door will stop and reverse to full open position, and the opener lights will flash 10 times.

The units must be installed inside the garage so that the sending and receiving eyes face each other across the door, no more than 6" above the floor. Either can be installed on the left or right of the door as long as the sun never shines directly into the receiving eye lens.

The mounting brackets are designed to clip onto the track of sectional garage doors without additional hardware.

WARNING

Be sure power is not connected to the garage door opener BEFORE installing the safety reversing sensor.

To prevent SERIOUS INJURY or DEATH from a closing garage door:

Correctly connect and align the safety reversing sensor. This required safety device MUST NOT be disabled.

Install the safety reversing sensor so beam is NO HIGHER than 6" above garage floor.

If it is necessary to mount the units on the wall, the brackets must be securely fastened to a solid surface such as the wall framing. Extension brackets (see accessories) are available if needed. If installing in masonry construction, add a piece of wood at each location to avoid drilling extra holes in masonry if repositioning is necessary.

The invisible light beam path must be unobstructed. No part of the garage door (or door tracks, springs, hinges, rollers or other hardware) may interrupt the beam while the door is closing.

Sensor Beam

Invisible Light Beam

Sensor Beam

6" max.

6" max.

Protection Area

above floor

above floor

 

Facing the door from inside the garage

17

INSTALLING THE BRACKETS

Be sure power to the opener is disconnected.

Install and align the brackets so the sensors will face each other across the garage door, with the beam no higher than 6" above the floor. They may be installed in one of three ways, as follows.

Garage door track installation (preferred):

Slip the curved arms over the rounded edge of each door track, with the curved arms facing the door. Snap into place against the side of the track. It should lie flush, with the lip hugging the back edge of the track, as shown in Figure 1.

If your door track will not support the bracket securely, wall installation is recommended.

Wall installation:

Place the bracket against the wall with curved arms facing the door. Be sure there is enough clearance for the sensor beam to be unobstructed.

If additional depth is needed, an extension bracket (see Accessories) or wood blocks can be used.

Use bracket mounting holes as a template to locate and drill (2) 3/16" diameter pilot holes on the wall at each side of the door, no higher than 6" above the floor.

Attach brackets to wall with lag screws (not provided).

If using extension brackets or wood blocks, adjust right and left assemblies to the same distance out from the mounting surface. Make sure all door hardware obstructions are cleared.

Floor installation:

Use wood blocks or extension brackets (see Accessories) to elevate sensor brackets so the lenses will be no higher than 6" above the floor.

Carefully measure and place right and left assemblies at the same distance out from the wall. Be sure all door hardware obstructions are cleared.

Fasten to the floor with concrete anchors as shown.

HARDWARE SHOWN ACTUAL SIZE

Carriage Bolt

Wing Nut

Staples

1/4"-20x1/2"

1/4"-20

 

Figure 1 Door Track Mount (Right Side)

DOOR TRACK MOUNT (RIGHT SIDE)

Door

Track

Lip

Indicator

light

Sensor

Bracket

Lens

Figure 2 Wall Mount (Right Side)

WALL MOUNT (RIGHT SIDE)

Inside

Extension

arage

G

Bracket

all

W

(See Accessories)

 

 

(Provided with

 

Extension Bracket)

(Provided with

Sensor

Bracket

Extension

 

Bracket)

Indicator

Lens

light

Figure 3 Floor Mount (Right Side)

FLOOR MOUNT (RIGHT SIDE)

Lens

Sensor

Bracket

(Provided with

 

Extension

Inside

Bracket)

arage

 

G

 

all

 

W

Indicator

light

(Provided with Extension Bracket)

Attach with concrete anchors (not provided)

Extension

Bracket

(See Accessories)

18

MOUNTING AND WIRING THE SAFETY SENSORS

Slide a 1/4"-20x1/2"carriage bolt head into the slot on each sensor. Use wing nuts to fasten sensors to brackets, with lenses pointing toward each other across the door. Be sure the lens is not obstructed by a bracket extension (Figure 4).

Finger tighten the wing nuts.

Run the wires from both sensors to the opener. Use insulated staples to secure wire to wall and ceiling.

Strip 7/16" of insulation from each set of wires. Separate white and white/black wires sufficiently to connect to the opener quick-connectterminals: white to white and white/black to grey (Figure 5).

ALIGNING THE SAFETY SENSORS

Plug in the opener. The indicator lights in both the sending and receiving eyes will glow steadily if wiring connections and alignment are correct.

The sending eye orange indicator light will glow regardless of alignment or obstruction. If the green indicator light in thereceiving eye is off, dim, or flickering (and the invisible light beam path is not obstructed), alignment is required.

Loosen the sending eye wing nut and readjust, aiming directly at the receiving eye. Lock in place.

Loosen the receiving eye wing nut and adjust sensor until it receives the sender’s beam. When the green indicator light glows steadily, tighten the wing nut.

Figure 5

Bell Wire

Finished

Ceiling

 

Sensor

 

Invisible Light Beam

Sensor

Protection Area

Figure 4

Wing nut

Carriage bolt

1/4"-20x1/2"

Lens

TROUBLESHOOTING THE SAFETY SENSORS

1.If the sending eye indicator light does not glow steadily after installation, check for:

Electric power to the opener.

A short in the white or white/black wires. These can occur at staples, or at opener connections.

Incorrect wiring between sensors and opener.

A broken wire.

2.If the sending eye indicator light glows steadily but the receiving eye indicator light doesn't:

Check alignment.

Check for an open wire to the receiving eye.

3.If the receiving eye indicator light is dim, realign either sensor.

NOTE: When the invisible beam path is obstructed or misaligned while the door is closing, the door will reverse. If the door is already open, it will not close.

The opener lights will blink 10 times. (If bulbs are not installed, 10 clicks can be heard.) See page 17.

Connect Wire to

Quick-ConnectTerminals

Sensor

Connections

Bell Wire

Red

White

White/black

 

 

wire

 

 

wire

 

 

 

Strip wire 7/16"

White

Grey

7/16"

 

 

 

Quick-ConnectTerminals

 

19

INSTALLATION STEP 11

Fasten the Door Bracket

Follow instructions which apply to your door type as illustrated below or on the following page.

A horizontal reinforcement brace should be long enough to be secured to two or three vertical supports. A vertical reinforcement brace should cover the height of the top panel.

Figure 1 shows one piece of angle iron as the horizontal brace. For the vertical brace, 2 pieces of angle iron are used to create a U-shapedsupport. The best solution is to check with your garage door manufacturer for an opener installation door reinforcement kit.

NOTE: Many door reinforcement kits provide for direct attachment of the clevis pin and door arm. In this case you will not need the door bracket; proceed to Step 12.

SECTIONAL DOORS

1.Center the door bracket on the previously marked vertical centerline used for the header bracket installation. Note correct UP placement, as stamped inside the bracket.

2.Position the top edge of the bracket 2"-4"below the top edge of the door, OR directly below any structural support across the top of the door.

3.Mark, drill holes and install as follows, depending on your door’s construction:

Metal or light weight doors using a vertical angle iron brace between the door panel support and the door bracket:

Drill 3/16" fastening holes. Secure the door bracket using the two 1/4"-14x5/8"self-threadingscrews. (Figure 2A)

Alternately, use two 5/16" bolts, lock washers and nuts (not provided). (Figure 2B)

Metal, insulated or light weight factory reinforced doors:

Drill 3/16" fastening holes. Secure the door bracket using the self-threadingscrews (Figure 3).

Wood Doors:

Use top and bottom or side to side door bracket holes. Drill 5/16" holes through the door and secure bracket with 5/16"x2" carriage bolts, lock washers and nuts (not provided). (Figure 4)

NOTE: The1/4"-14x5/8"self-threadingscrews are not intended for use on wood doors.

HARDWARE

SHOWN

ACTUAL SIZE

Self-ThreadingScrew1/4"-14x5/8"

CAUTION

To prevent damage to garage door, reinforce inside of door with angle iron both vertically and horizontally.

Header

Bracket

Door

Bracket

Location

 

HORIZONTAL AND VERTICAL

 

REINFORCEMENT IS NEEDED

 

FOR LIGHTWEIGHT GARAGE

Vertical

DOORS (FIBERGLASS,

Centerline

ALUMINUM, STEEL, DOORS

 

WITH GLASS PANEL, ETC).

 

(NOT PROVIDED)

Figure 1

 

 

 

Vertical

 

 

 

(Not Provided)

Reinforcement

 

 

 

 

Vertical

 

 

 

Vertical

Reinforcement

 

 

 

Centerline

Vertical

 

Bolt

 

 

 

5/16"-18x2"

 

 

Centerline

 

 

 

 

 

 

 

 

 

 

 

UP

 

 

Door

 

 

 

UP

Bracket

 

 

 

 

 

 

 

Lock Washer

Door

 

5/16"

Nut

Bracket

 

 

 

 

 

 

5/16"-18

 

 

 

 

Self-Threading

 

 

 

Figure 2B

Screw

 

 

 

1/4"-14x5/8"

 

 

 

 

Figure 2A

 

(Not Provided)

Inside Edge

 

of Door or

 

 

 

 

Reinforcement Board

 

Bolt

 

 

5/16"x2"

 

Vertical

 

UP

Centerline

 

 

UP

Vertical

 

 

 

 

Centerline

 

Self-Threading

Figure 4

Screw

 

 

 

1/4"-14x5/8"

 

 

Figure 3

20

ONE-PIECEDOORS

Please read and comply with the warnings and reinforcement instructions on the previous page. They apply to one-piecedoors also.

Center the door bracket on the top of the door, in line with the header bracket as shown. Mark either the left and right, or the top and bottom holes.

Metal Doors: Drill 3/16" pilot holes and fasten the bracket with the1/4"-14x5/8"self-threadingscrews provided.

Wood Doors: Drill 5/16" holes and use 5/16"x2" carriage bolts, lock washers and nuts (not provided) or5/16"x1-1/2"lag screws (not provided) depending on your installation needs.

NOTE: The door bracket may be installed on the top edge of the door if required for your installation. (Refer to the dotted line optional placement drawing.)

Header Wall

Finished Ceiling

2x4 Support

Header

Bracket

Door

Bracket

HARDWARE SHOWN

ACTUAL SIZE

Self-ThreadingScrew1/4"-14x5/8"

 

Self-Threading

 

Screw

Door

1/4"-14x5/8"

Top of Door

Bracket

(Inside

 

 

Garage)

 

Top Edge

 

of Door

 

Optional

 

Placement

Optional

Placement

of Door

Bracket

Vertical

Centerline of

Garage Door

 

 

METAL DOOR

HORIZONTAL AND VERTICAL

 

 

REINFORCEMENT IS NEEDED

Nut

Lock

FOR LIGHTWEIGHT GARAGE

5/16"-18

DOORS (FIBERGLASS,

 

Washer

ALUMINUM, STEEL, DOORS

 

5/16"

WITH GLASS PANEL, ETC).

Door

Top of Door

(NOT PROVIDED)

Bracket

(Inside

 

 

 

Garage)

 

 

Top Edge

 

 

of Door

 

 

Optional

 

 

Placement

 

 

Carriage Bolt

 

 

5/16"x2"

 

 

(Not provided)

For a door with no exposed framing,

 

WOOD DOOR

or for the optional installation, use

 

 

lag screws 5/16"x1-1/2"(Not provided)

 

to fasten door bracket.

 

 

21

INSTALLATION STEP 12

Connect Door Arm to Trolley

Follow instructions which apply to your door type as illustrated below and on the following page.

SECTIONAL DOORS ONLY

Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley. Slide the outer trolley back (away from the door) about 2" as shown in Figures 1, 2 and 3.

Figure 1:

Fasten straight door arm section to outer trolley with the 5/16"x1" clevis pin. Secure the connection with a ring fastener.

Fasten curved section to the door bracket in the same way, using the 5/16"x1-1/4"clevis pin.

Figure 2:

Bring arm sections together. Find two pairs of holes that line up and join sections. Select holes as far apart as possible to increase door arm rigidity.

Figure 3, Hole alignment alternative:

If holes in curved arm are above holes in straight arm, disconnect straight arm. Cut about 6" from the solid end. Reconnect to trolley with cut end down as shown.

Bring arm sections together.

Find two pairs of holes that line up and join with bolts, lock washers and nuts.

Pull the emergency release handle toward the opener at a 45° angle so that the trolley release arm is horizontal. Proceed to Adjustment Step 1, page 24. Trolley will re-engageautomatically when opener is operated.

HARDWARE SHOWN ACTUAL SIZE

 

Nut 5/16"-18Lock Washer 5/16" Ring Fastener

 

Clevis Pin

Clevis Pin

Hex Bolt

5/16"x1" (Trolley)

5/16"x1-1/4"(Door Bracket)

5/16"-18x7/8"

Inner Trolley

Outer Trolley

Clevis Pin

Ring 5/16"x1"

Fastener

Door

Bracket

Straight

Door Arm

Curved

Door Arm

Clevis Pin 5/16"x1-1/4"

Figure 1

Lock Washers 5/16"

Nuts

Emergency

5/16"-18

 

Release

 

Handle

Bolts 5/16"-18x7/8"

Door Bracket

Figure 2

Lock Washers 5/16"

Nuts 5/16"-18

Bolts 5/16"-18x7/8"

Cut This End

Figure 3

22

ALL ONE-PIECEDOORS

1.Assemble the Door Arm:

Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap).

Make sure the garage door is fully closed. Connect the straight door arm section to the door bracket with the 5/16"x1-1/4"clevis pin.

Secure with a ring fastener.

Pull the emergency release handle, disconnecting the outer trolley from the inner trolley by pulling straight down on the emergency release handle and sliding the outer trolley back toward the motor unit.

Connect the curved door arm section to the trolley using the 5/16"x1-1/4"clevis pin and ring fastener.

NOTE: Adjusting the limits on the following page:

The trolley will automatically connect. If not, review the trolley lockout feature on page 28.

When setting the up limit on the following page, the door should not have a "backward" slant when fully open as illustrated below. A slight backward slant will cause unnecessary bucking and/or jerking operation as the door is being opened or closed from the fully open position.

Door

Ring

 

 

Bracket

 

 

 

Fastener

 

Nuts

 

 

Lock

 

 

5/16"-18

 

 

Washers

 

 

 

Clevis Pin

Straight

5/16"

 

 

 

5/16"x1-1/4"

Arm

 

 

 

Bolts

 

Curved

 

5/16"-18x7/8

 

 

 

 

Door Arm

Fully Closed

Trolley

Door Arm

Connector Hole

Door Arm

Emergency Release Handle

Closed

Door

 

Fully Open

 

Trolley

Correct Angle

Door Arm

 

Connector Hole

 

 

 

 

Door

 

Arm

 

 

 

 

 

 

 

Door with

 

Open Door

Backward Slant

 

 

 

(Undesirable)

 

 

 

 

 

 

 

 

23

ADJUSTMENT 1

Program the travel limits

Travel limits regulate the points at which the door will stop when moving up or down. Follow the steps below to set the desired up limit. The down limit will be set automatically during step 5. During this step, use the remote control shipped with your opener. Any other remote will not work until its code is programmed into your opener’s receiver (see “Programming”).

1.Activate the door using the door control or the remote. The trolley will reconnect and the door will open between 4 and 5 feet.

2.Use the two buttons (1), (2) on the control panel to place the opener into limit setting mode:

Press and hold the “Learn” button (2) while you press the “Limit” button on the left (1), then release both buttons. The indicator light (3) will blink slowly. The opener is now in limit learn mode.

3.Press the left button (1) until the door travels up to the desired limit. If the door goes above the desired up limit, press the right button (2) to lower it. Check to be sure the door is high enough for your vehicle. Adjust if necessary, using both buttons.

4.Place a one-inchboard (or a 2x4 laid flat) on the floor, centered under the garage door.

5.Press the remote (4) or door control push button. The door will travel down, touch the board, then reverse and stop in the up limit position. The indicator light will stop blinking and turn off. The opener has learned the up and down limits. Remove the wood board.

During step 5, if the door reverses before touching the board, increase the down force (See “Force Adjustment”), then repeat steps 1-5above.

If the door stops before reaching the up limit, increase the up force by small adjustments until it reaches the up limit. (See “Force Adjustment”). Repeat step 5.

WARNING

Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door.

Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system.

If one control (force or travel limits) is adjusted, the other control may also need adjustment.

After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with one-inchhigh object (or 2x4 laid flat) on floor.

CAUTION

To prevent damage to vehicles, be sure fully open door provides adequate clearance.

Force

Adjustment

Antenna

 

Limit Button (1)

 

 

 

 

Indicator Light (3)

 

 

 

 

 

 

 

 

 

 

 

 

Learn Button (2)

 

 

(Left)

(Right)

(4)

LOCK

LIGHT

24

ADJUSTMENT STEP 2

Adjust the Force

Force adjustment controls are located on the back panel of the motor unit. Force adjustment settings regulate the amount of power required to open and close the door.

If the forces are set too light, door travel may be interrupted by nuisance reversals in the down direction and stops in the up direction. Weather conditions can affect the door movement, so occasional adjustment may be needed.

The maximum force adjustment range is about 3/4 of a complete turn. Do not force controls beyond that point. Turn force adjustment controls with a screwdriver.

NOTE: If anything interferes with the door’s upward travel, it will stop. If anything interferes with the door’s downward travel (including binding or unbalanced doors), it will reverse.

HOW AND WHEN TO ADJUST THE FORCES

1. Test the DOWN (close) force

Grasp the door bottom when the door is about halfway through DOWN (close) travel. The door should reverse. Reversal halfway through down travel does not guarantee reversal on a one-inch obstruction. See Adjustment Step 3, page 26.

If the door is hard to hold or doesn't reverse,

DECREASE the DOWN (close) force by turning the control counterclockwise. Make small adjustments until the door reverses normally. After each adjustment, run the opener through a complete cycle.

If the door reverses during the down (close) cycle and the opener lights aren't flashing,

INCREASE DOWN (close) force by turning the control clockwise. Make small adjustments until the door completes a close cycle. After each adjustment, run the opener through a complete travel cycle. Do not increase the force beyond the minimum amount required to close the door.

2. Test the UP (open) force

Grasp the door bottom when the door is about halfway through UP (open) travel. The door should stop. If the door is hard to hold or doesn't stop,

DECREASE UP (open) force by turning the control counterclockwise. Make small adjustments until the door stops easily and opens fully. After each adjustment, run the opener through a complete travel cycle.

If the door doesn’t open at least 5 feet,

INCREASE UP (open) force by turning the control clockwise. Make small adjustments until door opens completely. Readjust the UP limit if necessary. After each adjustment, run the opener through a complete travel cycle.

WARNING

Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door.

Too much force on garage door will interfere with proper operation of safety reversal system.

NEVER increase force beyond minimum amount required to close garage door.

NEVER use force adjustments to compensate for a binding or sticking garage door.

If one control (force or travel limits) is adjusted, the other control may also need adjustment.

After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with one-inchhigh object (or 2x4 laid flat) on floor.

UP DOWN

Force Force

 

9

1

kg

7 5 3

kg

Learn Button

Force

Adjustment

NOTE: Both Force Adjustments set at 3 before leaving factory

UP

 

 

DOWN

Force

 

 

Force

9

 

 

1

kg 7

5

3

kg

 

 

 

25

ADJUSTMENT STEP 3

Test the Safety Reversal System

TEST

With the door fully open, place a one-inchboard (or a 2x4 laid flat) on the floor, centered under the garage door.

Operate the door in the down direction. The door must reverse on striking the obstruction.

ADJUST

If the door stops on the obstruction, it is not traveling far enough in the down direction. See adjustment step 1.

NOTE: On a sectional door, make sure limit adjustments do not force the door arm beyond a straight up and down position. See the illustration on page 22.

Repeat the test.

When the door reverses on the one-inchboard, remove the obstruction and run the opener through 3 or 4 complete travel cycles to test adjustment.

IMPORTANT SAFETY CHECK:

Repeat Adjustment Steps 1, 2 and 3 after:

Each adjustment of door arm length, limits, or force controls.

Any repair to or adjustment of the garage door (including springs and hardware).

Any repair to or buckling of the garage floor.

Any repair to or adjustment of the opener.

WARNING

Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door.

Safety reversal system MUST be tested every month.

If one control (force or travel limits) is adjusted, the other control may also need adjustment.

After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with one-inchhigh object (or 2x4 laid flat) on the floor.

One-inchboard (or a 2x4 laid flat)

ADJUSTMENT STEP 4

Test the Protector System®

Press the remote control push button to open the door.

Place the opener carton in the path of the door.

Press the remote control push button to close the door. The door will not move more than an inch, and the opener lights will flash.

The garage door opener will not close from a remote if the indicator light in either sensor is off (alerting you to the fact that the sensor is misaligned or obstructed).

If the opener closes the door when the safety reversing sensor is obstructed (and the sensors are no more than 6" above the floor), call for a trained door systems technician.

WARNING

Without a properly installed safety reversing sensor, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door.

Safety Reversing Sensor

Safety Reversing Sensor

26

OPERATION

IMPORTANT SAFETY INSTRUCTIONS

WARNING

To reduce the risk of severe injury or death:

1.READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS.

2.ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with garage door control push buttons or remote controls.

3.ONLY activate garage door when it can be seen clearly, it is properly adjusted, and there are no obstructions to door travel.

4.ALWAYS keep garage door in sight until completely closed. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.

5.NO ONE SHOULD GO UNDER A STOPPED, PARTIALLY

OPEN DOOR.

6.If possible, use emergency release handle to disengage trolley ONLY when garage door is CLOSED. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly.

7.NEVER use emergency release handle unless garage doorway is clear of persons and obstructions.

8.NEVER use handle to pull garage door open or closed. If rope knot becomes untied, you could fall.

9.If one control (force or travel limits) is adjusted, the other control may also need adjustment.

10.After ANY adjustments are made, the safety reversal system MUST be tested.

11.Safety reversal system MUST be tested every month. Garage door MUST reverse on contact with one-inchhigh object (or a 2 x 4 laid flat) on the floor.

12.ALWAYS KEEP GARAGE DOOR PROPERLY BALANCED (see page 3). An improperly balanced door may not reverse when required and could result in SEVERE INJURY or DEATH.

13.All repairs to cables, spring assemblies and other hardware, all of which are under EXTREME tension, MUST be made by a trained door systems technician.

14.ALWAYS disconnect electric power to garage door opener BEFORE making any repairs or removing covers.

15.SAVE THESE INSTRUCTIONS.

Using Your Garage Door Opener

Your Security opener and hand-heldremote control have been factory programmed to a matching code which changes with each use, randomly accessing over 100 billion new codes. Your opener will operate with several Security remote controls utilizing up to 8 functions, and one Security Keyless Entry

System. If you purchase a new remote, or if you wish to deactivate any remote, follow the instructions in the Programming section.

Activate your opener with any of the following:

The hand-heldRemote Control:Hold the large push button down until the door starts to move.

The wall-mountedDoor Control:Hold the push bar down until the door starts to move.

The Keyless Entry (See Accessories) If provided with your garage door opener, it must be programmed before use. See Programming.

When the opener is activated (with the safety reversing sensor correctly installed and aligned)

1.If open, the door will close. If closed, it will open.

2.If closing, the door will reverse.

3.If opening, the door will stop.

4.If the door has been stopped in a partially open position, it will close.

5.If obstructed while closing, the door will reverse. If the obstruction interrupts the sensor beam, the opener lights will blink for five seconds.

6.If obstructed while opening, the door will stop.

7.If fully open, the door will not close when the beam is broken. The sensor has no effect in the opening cycle.

If the sensor is not installed, or is misaligned, the door won't close from a hand-heldremote. However, you can close the door with the Door Control, the Outside Keylock, or Keyless Entry,if you activate them until down travel is complete. If you release them too soon, the door will reverse.

The opener lights will turn on under the following conditions: when the opener is initially plugged in; when power is restored after interruption; when the opener is activated.

They will turn off automatically after 4-1/2minutes or provide constant light when the Light feature on theMulti-FunctionDoor Control is activated. Bulb size is 100 watts maximum.

Security light feature: Lights will also turn on when someone walks through the open garage door. With aMulti-FunctionDoor Control, this feature may be turned off as follows: With the opener lights off, press and hold the light button for 10 seconds, until the light goes on and off again. To restore this feature, start with the opener lights on, then press and hold the light button for 10 seconds until the light goes off, then on again.

27

Using the Wall-Mounted

Door Control

THE MULTI-FUNCTIONDOOR CONTROL

Press the push bar to open

 

Push Bar

or close the door. Press

 

again to reverse the door

 

 

during the closing cycle or

 

 

to stop the door while it's

LIGHT

Light Button

 

LOCK

 

opening.

 

 

Light feature

Lock Button

 

 

 

Press the Light button to

turn the opener light on or off. It will not control the opener lights when the door is in motion. If you turn it on and then activate the opener, the light will remain on for 4-1/2minutes. Press again to turn it off sooner.

Lock feature

Designed to prevent operation of the door from handheld remote controls. However, the door will open and close from the Door Control, the Outside Keylock and the Keyless Entry Accessories.

To activate, press and hold the Lock button for 2 seconds. The push bar light will flash as long as the Lock feature is on.

To turn off, press and hold the Lock button again for 2 seconds.The push bar light will stop flashing. The Lock feature will also turn off whenever the “Smart” (learn) button on the motor unit panel is activated.

Additional features when used with the 3-Channelhand-heldremote

A) To control the opener lights:

In addition to operating the door, you may program the remote to operate the lights.

1.With the door closed, press and hold a small remote button that you want to control the light.

2.Press and hold the Light button on the MultiFunction door control.

3.While holding the Light button, press and hold the Lock button on the door control.

4.After the opener lights flash,

release all buttons.

B)To operate one door using all three buttons on the hand-heldremote:

You may program the remote to

 

open the door with the large

Open

button, close it with the middle

Close

button, and stop the door’s

Stop

movement with the third button.

 

NOTE: If remote is already programmed, you must first erase all codes. See Programming.

1.With the door closed, press and hold the large remote push button.

2.Press and hold the Lock button on the door control for a minimum of one second before proceeding to next step.

3.Press and hold the door control push bar.

4.After the opener lights flash, release all buttons.

To Open the Door Manually

WARNING

To prevent possible SERIOUS INJURY or DEATH from a falling garage door:

If possible, use emergency release handle to disengage trolley ONLY when garage door is CLOSED. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly.

NEVER use emergency release handle unless garage doorway is clear of persons and obstructions.

NEVER use handle to pull door open or closed. If rope knot becomes untied, you could fall.

The door should be fully closed if possible. Pull down on the emergency release handle and lift the door manually. To reconnect the door to the opener, press the door control push bar.

Emergency

Release

Handle

(Pull Down)

Trolley

Release

Arm

NOTICE

The lockout featureprevents the trolley from reconnecting automatically, Pull the emergency release handle down and back (toward the opener). The door can then be raised and lowered manually as often as necessary. To disengage the lockout feature, pull the handle straight down. The trolley will reconnect on the next UP or DOWN operation.

MANUAL DISCONNECT

POSITION

Trolley

Release

Arm

Emergency

Release Handle

(Pull Down & Back

Towards Opener)

TICE

NO

 

LOCKOUT POSITION

28

CARE OF YOUR OPENER

LIMIT AND FORCE ADJUSTMENTS:

Weather conditions may cause some minor changes in door operation requiring some re-adjustments,particularly during the first year of operation.

Pages 24 and 25 refer to the limit and force adjustments. Only a screwdriver is required. Follow the instructions carefully.

UP

 

 

DOWN

Force

 

 

Force

9

 

 

1

kg 7

5

3

kg

 

 

 

FORCE CONTROLS (BACK PANEL)

Repeat the safety reverse test (Adjustment

Step 3, page 26) after any adjustment of limits or force.

THE REMOTE CONTROL BATTERY

The lithium battery should produce power for up to 5 years. To replace battery, use the

visor clip or screwdriver blade to pry open the case as shown. Insert battery positive side up.

Dispose of old battery properly.

MAINTENANCE SCHEDULE

Once a Month

Manually operate door. If it is unbalanced or binding, call a trained door systems technician.

Check to be sure door opens & closes fully. Adjust limits and/or force if necessary. (See pages 24 and 25.)

Repeat the safety reverse test. Make any necessary adjustments. (See Adjustment Step 3.)

Once a Year

Oil door rollers, bearings and hinges. The opener does not require additional lubrication. Do not grease the door tracks.

WARNING

To prevent possible SERIOUS INJURY or DEATH:

NEVER allow small children near batteries.

If battery is swallowed, immediately notify doctor.

NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

HAVING A PROBLEM?

1.The opener doesn't operate from either the Door Control or the remote control:

Does the opener have electric power? Plug a lamp into the outlet. If it doesn't light, check the fuse box or the circuit breaker. (Some outlets are controlled by a wall switch.)

Have you disabled all door locks? Review installation instruction warnings on page 7.

Is there a build-upof ice or snow under the door? The door may be frozen to the ground. Remove any restriction.

The garage door spring may be broken. Have it replaced.

2.Opener operates from the remote, but not from the Door Control:

Is the door control lit? If not, reverse the wires. If the opener runs, check for a faulty wire connection at the door control, a short under the staples, or a broken wire.

Are the wiring connections correct? Review

Installation Step 6, page 14.

3.The door operates from the Door Control, but not from the remote control:

Is the door push bar flashing? If your model has the Lock feature, make sure it is off.

Program the opener to match the remote control code. (Refer to instructions on the motor unit panel.) Repeat with all remotes.

4. The remote control has short range:

Change the location of the remote control in your car.

Check to be sure the antenna on the side or back panel of motor unit extends fully downward.

Some installations may have shorter range due to a metal door, foil backed insulation, or metal garage siding.

5.Opener noise is disturbing in living quarters of home:

If operational noise is a problem because of proximity of the opener to the living quarters, the Vibration Isolator Kit 41A3263 can be installed. This kit was designed to minimize vibration to the house and is easy to install.

29

Having a Problem? (Continued)

6. The garage door opens and closes by itself:

Be sure that all remote control push buttons are off.

Remove the bell wire from the door control terminals and operate from the remote only. If this solves the problem, the door control is faulty (replace), or there is an intermittent short on the wire between the door control and the motor unit.

Clear memory and re-programall remote controls.

7. The door doesn't open completely:

Is something obstructing the door? Is it out of balance, or are the springs broken? Remove the obstruction or repair the door.

If the door is in good working order but now doesn't open all the way, increase the up force. See Adjustment Step 2.

If the door opens at least 5 feet, the travel limits may need to be adjusted. See Adjustment Step 1.

8. The door stops but doesn't close completely:

Review the travel limits adjustment procedures on

Adjustment Step 1.

Repeat the safety reverse test after any adjustment of door arm length, close force or down limit.

9. The door opens but won't close:

If the opener lights blink, check the safety reversing sensor. See Installation Step 10.

If the opener lights don’t blink and it is a new installation, check the down force. See Adjustment Step 2. For an existing installation, see below.

Repeat the safety reverse test after the adjustment is complete.

10.The door reverses for no apparent reason and opener lights don’t blink:

Is something obstructing the door? Pull the emergency release handle. Operate the door manually. If it is unbalanced or binding, call a trained door systems technician.

Clear any ice or snow from the garage floor area where the door closes.

Review Adjustment Step 2.

Repeat safety reverse test after adjustments to force or travel limits. The need for occasional adjustment of the force and limit settings is normal. Weather conditions in particular can affect door travel.

11.The door reverses for no apparent reason and opener lights blink for 5 seconds after reversing:

Check the safety reversing sensor. Remove any obstruction or align the receiving eye. See

Installation Step 10.

12. The opener lights don't turn on:

Replace the light bulbs (100 watts maximum). Use a standard neck garage door opener bulb if regular bulb burns out.

13. The opener lights don't turn off:

• Is the Light feature on? Turn it off.

14.The opener strains or maximum force is needed to operate door:

The door may be out of balance or the springs may be broken. Close the door and use the emergency release handle to disconnect the trolley. Open and close the door manually. A properly balanced door will stay in any point of travel while being supported entirely by its springs. If it does not, disconnect the opener and call a trained door systems technician.Do not increase the force to operate the opener.

15.The opener motor hums briefly, then won't work:

The garage door springs may be broken. See above.

If the problem occurs on the first operation of the opener, door may be locked. Disable the door lock.

16.The opener won't operate due to power failure:

Use the emergency release handle to disconnect the trolley. The door can be opened and closed manually. When power is restored, press the Door Control push bar and trolley will automatically reconnect (unless trolley is in lockout position.) See page 28.

The Outside Quick Release accessory (for use on garages with no service door) disconnects the trolley from outside the garage in case of power failure.

30

PROGRAMMING

Your garage door opener has already been programmed at the factory to operate with your hand-heldremote control. The door will open and close when you press the large push button.

Below are instructions for programming your opener to operate with additional Security remote controls.

To Add an Additional Hand-heldRemote Control

USING THE “LEARN” BUTTON

 

USING THE MULTI-FUNCTIONDOOR CONTROL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LOCK

LIGHT

1.Press and release the “learn” button on the motor unit. The learn indicator light will glow steadily for 30 seconds.

2.Within 30 seconds, press and hold the button on the hand-heldremote* that you wish to operate your garage door.

3.Release the button when the motor unit lights blink. It has learned the code. If light bulbs are not installed, two clicks will be heard.

1.Press and hold the button on the hand-heldremote* that you wish to operate your garage door.

2.While holding the remote button, press and hold the LIGHT button on the Multi-FunctionDoor Control.

3.Continue holding both buttons while you press the push bar on the Multi-FunctionDoor Control (all three buttons are held).

4.Release buttons when the motor unit lights blink. It has learned the code. If light bulbs are not installed, two clicks will be heard.

LOCK

LIG

LOCK

LI

To Erase All Codes From Motor

Unit Memory

To deactivate any unwanted remote, first erase all codes:

Press and hold the “learn” button on motor unit until the learn indicator light

goes out (approximately 6 seconds). All previous codes are now erased. Reprogram each remote or keyless entry you wish to use.

*3-ChannelRemotes

If provided with your garage door opener, the large button is factory programmed to operate it. Additional buttons on any Security

3-channelremote ormini-remotecan be programmed to operate

other Security garage door openers.

31

To Add or Change a Keyless Entry PIN

NOTE: Your new Keyless Entry must be programmed to operate your garage door opener.

USING THE “LEARN” BUTTON

 

 

USING THE MULTI-FUNCTIONDOOR CONTROL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1. Press and release the “learn” button on motor unit. The learn indicator light will glow steadily for 30 seconds.

2.Within 30 seconds, enter a four digit personal identification

number (PIN) of your choice on the keypad. Then press and hold the ENTER button.

3.Release the button when the motor unit lights blink. It has learned the code. If light bulbs are not installed, two clicks will be heard.

To change an existing, known PIN

If the existing PIN is known, it may be changed by one person without using a ladder.

1.Press the four buttons for the present PIN, then press and hold the # button.

The opener light will blink twice. Release the # button.

2.Press the new 4-digitPIN you have chosen, then press Enter.

The motor unit lights will blink once when the PIN has been learned.

Test by pressing the new PIN, then press Enter. The door should move.

To set a temporary PIN

LOCK

LIGHT

NOTE: This method requires two people if the Keyless Entry is already mounted outside the garage.

1.Enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold ENTER.

2.While holding the ENTER button, press and hold the LIGHT button on the Multi-FunctionDoor Control.

3.Continue holding the ENTER and LIGHT buttons while you press the push bar on the Multi-FunctionDoor Control (all three buttons are held).

4.Release buttons when the motor unit lights blink. It has learned the code. If light bulbs are not installed, two clicks will be heard.

LOCK

LIG

LOCK

LI

2.Press the temporary 4-digitPIN you have chosen, then press Enter.

The opener light will blink four times.

3.To set the number of hours this temporary PIN will work, press the number of hours (up to 255), then press .

OR

You may authorize access by visitors or service people with a temporary 4-digitPIN. After a programmed number of hours or number of accesses, this temporary PIN expires and will no longer open the door. It can be used toclose the door even after it has expired. To set a temporary PIN:

1.Press the four buttons for your personal entry PIN (not the last temporary PIN), then press and hold thebutton.

The opener light will blink three times. Release the button.

3.To set the number of times this temporary PIN will work, press the number of times (up to 255), then press #.

The opener light will blink once when the temporary PIN has been learned.

Test by pressing the four buttons for the temporary PIN, then press Enter. The door should move. If the temporary PIN was set to a certain number of openings, remember that the test has used up one opening.To clear the temporary password, repeat steps 1-3,setting the number of hours or times to 0 in step 3.

32

REPAIR PARTS

Rail Assembly Parts

 

 

 

 

 

 

 

6

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

1

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

7

 

 

 

 

 

 

 

 

2

 

 

 

 

 

 

 

 

 

 

 

 

5

KEY

PART

 

 

 

 

 

 

 

 

 

 

 

 

NO.

NO.

 

DESCRIPTION

 

 

 

 

 

1

4A1008

Master link kit

 

 

 

 

 

2

41A5424

Belt pulley bracket

 

 

 

 

 

3

41B3869-1

Complete trolley assembly

8

 

 

 

 

4

109B33

Trolley clip

 

 

 

 

5

183B99

One-pieceT-rail

 

 

 

 

 

6

41A5434-11Full belt assembly

 

 

 

 

 

7

41B4103

Tensioner assembly

 

 

 

 

 

8

83A11-2

Rail grease

Installation Parts

 

 

 

 

 

 

 

 

2

 

 

 

6

 

 

 

 

 

 

5

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

N

 

 

 

 

 

 

 

 

O

 

 

 

 

 

 

 

 

TIC

 

 

 

 

 

 

4

 

E

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

KEY

PART

 

 

 

 

 

 

NO.

NO.

 

DESCRIPTION

 

 

 

 

 

7

 

G MOUN

 

1

41C494

 

Multi-functiondoor control panel

 

NLY

 

 

 

 

 

 

 

T O

 

 

 

 

 

 

CEI

LIN

 

2

41A5056-3

3-Channelremote control housing

UP

 

1

 

 

 

 

 

 

 

 

 

 

(no circuit board)

 

 

 

 

3

10A20

 

3V2032 Lithium battery

LOCK

 

 

 

4

29B137

 

Remote control visor clip

LIGHT

 

 

 

 

 

10

 

 

 

 

5

41A2828

 

Emergency release rope & handle assy

 

 

 

 

 

 

 

 

 

6

217A238

 

2-Conductorbell wire - white &

 

 

 

 

 

 

 

white/red

 

 

 

 

7

41A5047-1

Door bracket w/clevis pin & fastener

9

11

 

 

8

41A4353-1

Header bracket w/clevis pin & fastener

 

 

 

 

9

41A5034

 

Safety sensor kit (receiving and

 

 

 

 

 

 

 

sending eyes) with 3' 2-conductor

12

 

 

 

 

 

 

bell wire attached

 

 

 

10

178B34

 

Straight door arm section

 

 

 

 

11

178B35

 

Curved door arm section

 

 

 

 

12

41A5266-1

Safety sensor brackets (2)

 

 

 

 

 

NOT SHOWN

 

 

 

 

 

 

 

41A2770-5Installation hardware bag

 

 

 

 

 

 

 

(includes hardware listed on page 5)

 

 

 

 

 

114A2503

Owner's manual

33

Motor Unit Assembly Parts

1

4

 

 

2

13

 

3

10

5

 

 

 

 

 

9

 

 

8

 

 

6

7

12

11

 

KEY

PART

 

KEY

PART

 

 

 

 

 

 

 

NO.

NO.

DESCRIPTION

NO.

NO.

DESCRIPTION

 

 

1

41A4371-1

Belt cap

7

41A5507

Receiver logic board assy with

 

 

2

41B4245-1

Line cord

 

 

end panel

 

 

 

41D183

End panel only

 

 

3

41B3150-1

Terminal block w/screws

 

 

 

8

41B5351-4

Power supply

 

 

4

41C53

Belt cog

 

 

9

41C153

Transformer

 

 

5

41C5317

Wire harness

 

 

10

41D630-2

Bracket: light socket, limit switch

 

 

 

41C5511

High voltage wire harness

 

 

 

11

41A5490-10

Cover

 

 

 

41B5405

DC motor wire harness

 

 

 

12

175C147

Light socket

 

 

 

41C5418

Light socket wire harness

 

 

 

13

108D60

Light lens

 

 

6

41D475

Motor 80kg/100kg

 

 

 

 

 

 

 

 

 

 

 

 

 

 

34

ACCESSORIES

1702LM Outside Quick Release:

Required for a garage with NO access door. Enables homeowner to open garage door manually from outside by disengaging trolley.

2778BD

8 Foot Complete Rail:

 

To allow an 8 foot door to open fully.

2770BD

10 Foot Complete Rail:

 

To allow a 10 foot door to open fully.

41A5281 Extension Brackets:

(Optional) For safety sensor installation onto the wall or floor.

976LM

Wireless Keyless Entry with

 

Security ™:

 

Enables homeowner to operate garage

 

door opener from outside by entering a

 

password on a specially designed

 

keyboard. Also can add a temporary

 

password for visitors or service

 

persons. This temporary password can

 

be limited to a programmable number

 

of hours or entries.

902LM/903LM

2 & 3 Door Multi-FunctionWall

 

Control:

 

Ideal for homes with up to three

 

garage doors. Combine up to three

 

controls into one wall control panel for

 

a neat compact appearance.

 

Enhanced functions include Lock

 

Feature to lock out outside radio

 

signals while you are away from

 

home and turn opener lights on or

 

off from the control panel.

995LM

973LM

974LM

970LM

Model 98LM

LOCK

LIGHT

915LM

CLOSED

OPEN

916LM

Remote Light Control:

Enables homeowner to turn on a lamp, television or other appliance from their car with their garage door opener remote or from anywhere in their home with an additional LiftMaster Security ™ remote.

3-ButtonSecurity ™ Remote Control:

Includes visor clip.

4-ButtonSecurity ™ Remote Control:

Includes visor clip.

3-ButtonMini-RemoteControl with Security ™:

With key ring and velcro fastening strip.

Motion Detecting Control Panel:

Multi-functiondoor control with motion sensor that automatically turns opener lights on for 5 minutes when it detects a person entering the garage. Sensor can be easily deactivated when desired.

Garage Door Monitor:

Security for the largest door of your home!

Tells you if your garage door is open or closed. Monitors up to 4 garage doors by adding additional sensor modules.

Garage Door Monitor Sensor:

Additional accessory sensor for homes with multiple garage doors.

35

LIFTMASTER SERVICE IS

ON CALL

OUR LARGE SERVICE ORGANIZATION

SPANS AMERICA

INSTALLATION AND SERVICE INFORMATION IS AS NEAR AS YOUR TELEPHONE SEVEN DAYS A WEEK. SIMPLY DIAL OUR TOLL FREE NUMBER:

1-800-528-2817

HOURS: (Central Std. Time)

6:00 A.M. TO 7:00 P.M. Monday through Friday 8:00 A.M. TO 6:00 P.M. Saturday

8:00 A.M. TO 4:30 P.M. Sunday

www.liftmaster.com

For professional installation, parts and service, contact your local LIFTMASTER/ CHAMBERLAIN dealer. Look for him in the Yellow Pages, or call our service number for a list of dealers in your area.

HOW TO ORDER

REPAIR PARTS

Selling prices will be furnished on request or parts will be shipped at prevailing prices and you will be billed accordingly.

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:

PART NUMBER

PART NAME

MODEL NUMBER

ADDRESS ORDERS TO:

THE CHAMBERLAIN GROUP, INC.

Technical Support Group

6020 S. Country Club Road

Tucson, Arizona 85706

SERVICE INFORMATION TOLL FREE NUMBER:

1-800-528-2817

LIFTMASTER GARAGE DOOR OPENER FIVE-YEARLIMITED WARRANTY

The Chamberlain Group, Inc. (“Seller”) warrants to the first retail purchaser of this product, for the residence in which this product is originally installed, that it will be free from any defect in materials and/or workmanship for a period of 60 full months from the date of purchase. Additionally, the motor and drive belt are warranted for the lifetime of the product. The product must be used in complete accordance with Chamberlain’s instructions for installation, operation and care. The proper operation of this product is dependent on your compliance with the Owner’s Manual instructions regarding installation, operation, maintenance and testing. Failure to comply strictly with those instructions will void this warranty in its entirety. Please note that the safety reverse system, in order to operate properly with your garage door, must be adjusted and periodically tested in accordance with the Owner’s Manual.

If, during the limited warranty period, it appears as though this product contains a defect which is covered by this limited warranty, CALL OUR TOLL FREE SERVICE NUMBER, BEFORE DISMANTLING THIS PRODUCT, AT (1-800-528-2817). Then send this product, prepaid and insured, to our service center for warranty repair. You will be advised of shipping instructions when you call the toll free service number. Please include a brief description of the problem and a datedproof-of-purchasereceipt with any product that is returned for warranty repair.

Products returned to Seller for warranty repair, which upon receipt by Seller are confirmed to be defective and covered by this limited warranty, will be repaired or replaced (at Seller’s sole option) at no cost to you and returned pre-paid.Defective parts will be repaired or replaced with new orfactory-rebuiltparts at Seller’s sole option.

THIS LIMITED WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR OTHERWISE, AND OF ANY OTHER OBLIGATIONS OR LIABILITY ON SELLER’S PART. THIS LIMITED WARRANTY DOES NOT COVER NON-DEFECTDAMAGE, DAMAGE CAUSED BY IMPROPER INSTALLATION, OPERATION OR CARE (INCLUDING, BUT NOT LIMITED TO ABUSE, MISUSE, FAILURE TO PROVIDE REASONABLE AND NECESSARY MAINTENANCE, USE OF UNAUTHORIZED PARTS OR ACCESSORIES, UNAUTHORIZED REPAIRS, OR ANY ALTERATIONS TO THIS PRODUCT), LABOR CHARGES FOR DISMANTLING OR REINSTALLING A REPAIRED OR REPLACED UNIT, REPLACEMENT OF BATTERIES AND LIGHT BULBS, OR UNITS INSTALLED FORNON-RESIDENTIALUSE.THE USE OF UNAUTHORIZED PARTS OR ACCESSORIES WILL VOID THIS LIMITED WARRANTY. If you have any questions as to whether accessories or replacement parts are authorized, please contact Chamberlain.

THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH, OR RELATING TO, THE GARAGE DOOR OR GARAGE DOOR HARDWARE, INCLUDING BUT NOT LIMITED TO THE DOOR SPRINGS, DOOR ROLLERS, DOOR ALIGNMENT AND HINGES. ANY SERVICE CALL THAT DETERMINES THE PROBLEM HAS BEEN CAUSED BY ANY OF THESE ITEMS COULD RESULT IN A FEE TO YOU.

UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES ARISING IN CONNECTION WITH THE USE OF, OR INABILITY TO USE, THIS PRODUCT. IN NO EVENT SHALL SELLER’S LIABILITY FOR BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE OR STRICT LIABILITY EXCEED THE COST OF THE PRODUCT COVERED HEREBY. NO PERSON IS AUTHORIZED TO ASSUME FOR US ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT.

Some states do not allow the exclusion or limitation of consequential, incidental or special damages, so the above limitation or exclusion may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

LIFETIME MOTOR & BELT WARRANTY

The motor and belt are fully warranted for the lifetime of the product to the first-timepurchaser.

 

© 2003, The Chamberlain Group, Inc.

 

114A2503G

All Rights Reserved

Printed in Mexico