Lift-Master 2245 User Manual

Size:
2.52 Mb
Download

The Chamberlain Group, Inc. 845 Larch Avenue

Elmhurst, Illinois 60126-1196www.liftmaster.com

®

®

GARAGE DOOR OPENER

Models 2245 1/3 HP 2255 1/2 HP 2255-21/2 HP

For Residential Use Only

Owner’s Manual

Please read this manual and the enclosed safety materials carefully!

Fasten the manual near the garage door after installation.

The door WILL NOT CLOSE unless the Protector SystemÆ is connected and properly aligned.

Periodic checks of the opener are required to ensure safe operation.

The model number label is located on the front panel of your opener.

TABLE OF CONTENTS

 

Introduction

2-5

Safety symbol and signal word review........................

2

Preparing your garage door ........................................

3

Tools needed...............................................................

3

Planning .....................................................................

4

Carton inventory ..........................................................

5

Hardware inventory .....................................................

5

Assembly

6-7

Attach the rail to the motor unit...................................

6

Attach the chain to the sprocket..................................

6

Tighten the chain.........................................................

7

Installation

7-22

Installation safety instructions .....................................

7

Determine the header bracket location .......................

8

Install the header bracket............................................

9

Attach the rail to the header bracket.........................

10

Position the opener ...................................................

11

Hang the opener .......................................................

12

Install the door control...............................................

13

Install the light ...........................................................

14

Attach the emergency release rope and handle

.......14

Electrical requirements..............................................

15

Install the Protector SystemÆ................................

16-18

Fasten the door bracket.......................................

19-20

Connect the door arm to the trolley .....................

21-22

Adjustment

23-25

Adjust the travel limits ...............................................

23

Adjust the force .........................................................

24

Test the safety reversal system.................................

25

Test the Protector SystemÆ........................................

25

Operation

26-30

Operation safety instructions.....................................

26

Using your garage door opener ................................

26

Using the wall-mounteddoor control ........................

27

To open the door manually........................................

27

Care of your garage door opener..............................

28

Having a problem? ....................................................

29

Diagnostic chart.........................................................

30

Programming

31-32

To add or reprogram a hand-heldremote control .....31

To erase all codes .....................................................

31

3-Buttonremotes.......................................................

31

To add, reprogram or change

 

a Keyless Entry PIN ..................................................

32

Repair Parts

33-34

Rail assembly parts...................................................

33

Installation parts ........................................................

33

Motor unit assembly parts .........................................

34

Accessories

35

Repair Parts and Service

36

Warranty

36

INTRODUCTION

Safety Symbol

and Signal Word Review

This garage door opener has been designed and tested to offer safe service provided it is installed, operated, maintained and tested in strict accordance with the instructions and warnings contained in this manual.

WARNING

Mechanical

WARNING

Electrical

CAUTION

When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury or death if you do not comply with the warnings that accompany them. The hazard may come from something mechanical or from electric shock. Read the warnings carefully.

When you see this Signal Word on the following pages, it will alert you to the possibility of damage to your garage door and/or the garage door opener if you do not comply with the cautionary statements that accompany it. Read them carefully.

2

Preparing your garage door

Before you begin:

ïDisable locks.

ïRemove any ropes connected to garage door.

ïComplete the following test to make sure your garage door is balanced and is not sticking or binding:

1.Lift the door about halfway as shown. Release the door. If balanced, it should stay in place, supported entirely by its springs.

2.Raise and lower the door to see if there is any binding or sticking.

If your door binds, sticks, or is out of balance, call a trained door systems technician.

Sectional Door

One-PieceDoor

WARNING

To prevent possible SERIOUS INJURY OR DEATH:

ALWAYS call a trained door systems technician if garage door binds, sticks, or is out of balance. An unbalanced garage door may not reverse when required.

NEVER try to loosen, move or adjust garage door, door springs, cables, pulleys, brackets or their hardware, all of which are under EXTREME tension.

Disable ALL locks and remove ALL ropes connected to garage door BEFORE installing and operating garage door opener to avoid entanglement.

CAUTION

To prevent damage to garage door and opener:

ALWAYS disable locks BEFORE installing and operating the opener.

ONLY operate garage door opener at 120V, 60 Hz to avoid malfunction and damage.

Tools needed

During assembly, installation and adjustment of the opener, instructions will call for hand tools as illustrated below.

Carpenter's

Level (Optional)

Pencil

1

2

Hack Saw

Tape Measure

Wire Cutters

 

Drill

3/16", 5/16" and

 

Claw Hammer

 

 

5/32" Drill Bits

 

Pliers

 

 

 

 

Stepladder

1/2" and 7/16" Sockets

Screwdriver

 

and Wrench

 

Adjustable End Wrench

 

 

 

3

Planning

Identify the type and height of your garage door. Survey your garage area to see if any of the conditions below apply to your installation. Additional materials may be required. You may find it helpful to refer back to this page and the accompanying illustrations as you proceed with the installation of your opener.

SECTIONAL DOOR INSTALLATION

Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum,

door with glass panels, etc.). See page 19 for details.

Header Wall

— —

Vertical Centerline

of Garage Door

— — —

 

— —

 

FINISHED CEILING

Support bracket & fastening hardware is required.

See page 12.

Slack in chain tension is normal when garage door is closed.

Extension Spring

OR

Torsion Spring

Access Door

Safety

Reversing

Sensor

Motor Unit

Wallmounted Door Control

Gap between floor and bottom of door must not exceed 1/4" (6 mm).

Safety Reversing Sensor

ONE-PIECEDOOR WITHOUT TRACK

Slack in chain tension is normal when garage door is closed.

Header

Wall

FINISHED CEILING

Support bracket & fastening hardware is required. See page 12.

Motor Unit

Wallmounted Door Control

Access

Door

ONE-PIECEDOOR WITH TRACK

Slack in chain tension is normal when garage door is closed.

Safety Reversing Sensor

Gap between floor and bottom of Safety door must not exceed 1/4" (6 mm). Reversing Sensor

Safety

Reversing Sensor

Gap between floor and bottom of door must not exceed 1/4"

Access

Door

Safety Reversing

Sensor

(6 mm).

4

Carton Inventory

Your garage door opener is packaged in two cartons which contain the motor unit and all parts illustrated below. Accessories will depend on the model

purchased. If anything is missing, carefully check the packing material. Parts may be stuck in the foam. Hardware for installation is also listed below.

2245 (1), 2255 (1), 2255-2(2)

Sprocket Cover

LOCK

 

Remote Control

LIGHT

 

Multi-Function

SECURITY ®

Visor Clip

Single-ButtonRemote Control

 

Door Control Panel

 

 

 

 

Chain

Styrofoam

Motor Unit with Light Lens

 

 

LY

 

NT

ON

 

 

G

MOU

 

ILIN

 

 

CE

 

 

 

UP

 

Header Bracket

Chain

Pulley Bracket

Safety Sensor

Bracket (2)

2 Conductor Bell Wire

White & White/Red

One-Piece

Rail

Trolley

Door Bracket

(2) Safety Reversing Sensors

(1 Sending Eye and 1 Receiving Eye) with 2-ConductorWhite & White/Black Bell Wire attached

Curved Door

Arm Section

Safety Labels

and

Literature Straight Door

Arm Section

INSTALLATION HARDWARE

 

Hex Bolt 5/16"-18x7/8"(4)

Insulated Staples (30)

Lag Screw 5/16"-9x1-5/8"(2)

Ring Fastener (3)

Lag Screw 5/16"-18x1-7/8"(2)

Drywall Anchors (2)

Clevis Pin 5/16"x2-3/4"(1)

Rail Grease

Clevis Pin 5/16"x1-1/4"(1)

Carriage Bolt 1/4"-20x1/2"(2)

Clevis Pin 5/16"x1" (1)

Wing Nut 1/4"-20(2)

Nut 5/16"-18(4)

Rope

Lock Washer 5/16" (4)

Handle

Screw 6ABx1-1/4"(2)

 

Screw 6-32x1"(2)

 

Self-ThreadingScrew1/4"-14x5/8"(2)

 

 

 

5

ASSEMBLY STEP 1

Attach the Rail to the Motor Unit

To avoid installation difficulties, do not run the garage door opener until instructed to do so.

ïRemove the two washered bolts mounted in top of motor unit.

ïPosition rail at a 45˚ angle to opener so one hole in rail and motor unit line up.

ïThread one of the washered bolts part way in.

Use only these bolts! Use of any other bolts will cause serious damage to door opener.

ïAlign rail and styrofoam over sprocket. Cut tape from rail, chain and styrofoam.

ïREMOVE STYROFOAM.

CAUTION

To avoid SERIOUS damage to garage door opener, use ONLY those bolts/fasteners mounted in the top of the opener.

USE ONLY THIS

TYPE AND SIZE

BOLT Washered Bolt5/16"-18x1/2"

Styrofoam

Rail

Hole

ASSEMBLY STEP 2

Attach the Chain to the Sprocket and Install the Sprocket Cover

ïPosition chain over the sprocket. If necessary, loosen the outer nut on the trolley to obtain more chain slack.

ïInsert the second washered bolt. CAUTION: Use only the bolt previously removed from motor unit!

ïTighten both bolts securely through the rail into the motor unit as shown.

ïInstall the sprocket cover: Insert the back tab in the slot. Squeeze the cover slightly and insert the front tab in the slot on the mounting plate.

WARNING

To avoid possible SERIOUS INJURY to fingers from moving garage door opener:

ALWAYS keep hand clear of sprocket while operating opener.

Securely attach sprocket cover BEFORE operating.

Washered Bolts

5/16"-18x1/2"

Sprocket

USE ONLY THIS

TYPE AND SIZE

BOLT

Sprocket Cover

Back Tab Slot

Front Tab Slot

Mounting

 

 

Plate

6

ASSEMBLY STEP 3

Tighten the Chain

ïSpin the inner nut and lock washer down the trolley threaded shaft, away from the trolley.

ïTo tighten the chain, turn outer nut in the direction shown (Figure 1).

ïWhen the chain is approximately 1/2" (13 mm) above the base of the rail at its midpoint, re-tightenthe inner nut to secure the adjustment.

Sprocket noise can result if chain is too loose.

When installation is complete, you may notice some chain droop with the door closed. This is normal. If the chain returns to the position shown in Figure 2 when the door is open, do not re-adjustthe chain.

NOTE: During future maintenance, ALWAYS pull the emergency release handle to disconnect trolley before adjusting chain.

NOTE: You may notice loosening of chain after Adjustment Step 3 (Test the Safety Reversal System). Check for proper tension and readjust chain if necessary. Then repeat Adjustment Step 3.

You have now finished assembling your garage door opener. Please read the following warnings before proceeding to the installation section.

Figure 1

 

Lock

 

Outer Nut

Washer

Inner Nut

To Tighten Outer Nut

 

 

 

 

 

To Tighten

 

 

Inner Nut

Trolley

 

 

Figure 2

 

 

Chain

 

 

1/2" (13 mm)

Base of Rail Mid Length of Rail

INSTALLATION

IMPORTANT INSTALLATION INSTRUCTIONS

WARNING

To reduce the risk of SEVERE INJURY or DEATH:

1.READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCTIONS.

2.Install garage door opener only on properly balanced and lubricated garage door. An improperly balanced door may not reverse when required and could result in SEVERE INJURY or DEATH.

3.All repairs to cables, spring assemblies and other hardware MUST be made by a trained door systems technician BEFORE installing opener.

4.Disable all locks and remove all ropes connected to garage door BEFORE installing opener to avoid entanglement.

5.Install garage door opener 7 feet (2.13 m) or more above floor.

6.Mount emergency release handle 6 feet (1.83 m) above floor.

7.NEVER connect garage door opener to power source until instructed to do so.

8.NEVER wear watches, rings or loose clothing while installing or servicing opener. They could be caught in garage door or opener mechanisms.

9.Install wall-mountedgarage door control:

within sight of the garage door.

out of reach of children at minimum height of 5 feet

(1.5 m).

away from all moving parts of the door.

10.Place entrapment warning label on wall next to garage door control.

11.Place manual release/safety reverse test label in plain view on inside of garage door.

12.Upon completion of installation, test safety reversal system. Door MUST reverse on contact with a 1-1/2"(3.8 cm) high object (or a 2x4 laid flat) on the floor.

7

INSTALLATION STEP 1

Determine the Header Bracket

Location

WARNING

To prevent possible SERIOUS INJURY or DEATH:

Header bracket MUST be RIGIDLY fastened to structural support on header wall or ceiling, otherwise garage door might not reverse when required. DO NOT install header bracket over drywall.

Concrete anchors MUST be used if mounting header bracket or 2x4 into masonry.

NEVER try to loosen, move or adjust garage door, springs, cables, pulleys, brackets, or their hardware, all of which are under EXTREME tension.

ALWAYS call a trained door systems technician if garage door binds, sticks, or is out of balance. An unbalanced garage door might not reverse when required.

Installation procedures vary according to garage door types. Follow the instructions which apply to your door.

1.Close the door and mark the inside vertical centerline of the garage door.

2.Extend the line onto the header wall above the door.

You can fasten the header bracket within 4 feet (1.22 m) of the left or right of the door center only if a torsion spring or center bearing plate is in the way; or you can attach it to the ceiling (see page 9) when clearance is minimal. (It may be mounted on the wall upside down if necessary, to gain approximately 1/2" (1 cm).

If you need to install the header bracket on a 2x4 (on wall or ceiling), use lag screws (not provided) to securely fasten the 2x4 to structural supports as shown here and on page 9.

3.Open your door to the highest point of travel as shown. Draw an intersecting horizontal line on the header wall above the high point:

ï2" (5 cm) above the high point for sectional door and one-piecedoor with track.

ï8" (20 cm) above the high point for one-piecedoor without track.

This height will provide travel clearance for the top edge of the door.

NOTE: If the total number of inches exceeds the height available in your garage, use the maximum height possible, or refer to page 9 for ceiling installation.

 

Unfinished

 

OPTIONAL

 

Ceiling

 

 

 

CEILING

 

 

 

 

 

 

MOUNT

 

 

 

FOR

 

 

 

HEADER

 

 

2x4

BRACKET

Header Wall

 

 

 

 

 

 

Vertical Centerline

 

 

 

of Garage Door

 

 

 

 

2x4

Structural

 

 

 

 

 

 

Supports

Level (optional)

Header Wall

 

2" (5 cm) Track

Header Wall Track

 

2" (5 cm)

Highest Point

 

of Travel

Highest Point

 

 

of Travel

 

Door

Door

 

Sectional door with curved track

One-piecedoor with horizontal track

 

 

Header Wall

 

Header Wall

8" (20 cm)

 

8" (20 cm)

 

 

Highest

Highest

Door

Point

 

Point

of Travel

 

of Travel

Door

Jamb

 

 

Hardware

 

 

 

 

Pivot

One-piecedoor without track:

One-piecedoor without track:

jamb hardware

pivot hardware

8

INSTALLATION STEP 2

Install the Header Bracket

You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry, use concrete anchors (not provided).

WALL HEADER BRACKET INSTALLATION

ïCenter the bracket on the vertical centerline with the bottom edge of the bracket on the horizontal line as shown (with the arrow pointing toward the ceiling).

ïMark the vertical set of bracket holes (do not use the holes designated for ceiling mount). Drill 3/16" pilot holes and fasten the bracket securely to a structural support with the hardware provided.

HARDWARE SHOWN ACTUAL SIZE

Lag Screw 5/16"-9x1-5/8"

CEILING HEADER BRACKET INSTALLATION

ïExtend the vertical centerline onto the ceiling as shown.

ïCenter the bracket on the vertical mark, no more than 6"(15 cm) from the wall. Make sure the arrow is pointing toward the wall. The bracket can be mounted flush against the ceiling when clearance is minimal.

ïMark the side holes. Drill 3/16" pilot holes and fasten bracket securely to a structural support with the hardware provided.

Ceiling Mounting Holes

CEILING MOUNT ONLY

UP

The nail hole is for positioning only.

You must use lag screws

to mount the header bracket.

Wall Mounting Holes

CEILING MOUNT ONLY

UP

Optional

Wall Mounting Holes

Header

 

 

Wall

G M

LY

 

NT

ON

 

 

 

OU

 

 

ILIN

 

 

CE

 

 

UP

 

The nail hole is for positioning only.

You must use lag screws

to mount the header bracket.

Vertical

Centerline of

Garage Door

Lag Screws 5/16"x9x1-5/8"

2x4

Header

Structural

Bracket

Support

 

Door Spring

Horizontal

Line

Garage

Door

Highest Point of

Garage Door Travel Vertical

Centerline of

Garage Door

– Finished Ceiling –

 

 

Vertical

Header

Centerline

of Garage Door

Bracket

 

 

 

 

 

 

 

 

 

 

 

 

6" (15 cm)

PU

Maximum

 

Door

Spring Lag Screws

5/16"-9x1-5/8"

Header Wall

Garage Door

Vertical

Centerline

of Garage Door

9

Header Wall

Header Bracket

Chain Pulley

Bracket

INSTALLATION STEP 3

Attach the Rail to the Header Bracket

ïPosition the opener on the garage floor below the header bracket. Use packing material as a protective base. NOTE: If the door spring is in the way you’ll need help. Have someone hold the opener securely on a temporary support to allow the rail to clear the spring.

ïPosition the rail bracket against the header bracket.

ïAlign the bracket holes and join with a clevis pin as shown.

ï Insert a ring fastener to secure.

Rail

Ring Fastener

Header Bracket

 

 

Clevis Pin

 

5/16"x2-3/4"

 

Chain

 

Pulley

 

Bracket

 

Rail

Garage

 

Door

 

 

Temporary

 

Support

HARDWARE SHOWN ACTUAL SIZE

Clevis Pin

 

5/16"x2-3/4"

Ring Fastener

10

INSTALLATION STEP 4

Position the Opener

Follow instructions which apply to your door type as illustrated.

SECTIONAL DOOR OR ONE-PIECEDOOR WITH TRACK

A 2x4 laid flat is convenient for setting an ideal door-to-raildistance.

ïRemove foam packaging.

ïRaise the opener onto a stepladder. You will need help at this point if the ladder is not tall enough.

ïOpen the door all the way and place a 2x4 laid flat on the top section beneath the rail.

ïIf the top section or panel hits the trolley when you raise the door, pull down on the trolley release arm to disconnect inner and outer sections. Slide the outer trolley toward the motor unit. The trolley can remain disconnected until Installation Step 12

is completed.

Trolley

Release Arm

ENGAGED

RELEASED

CAUTION

To prevent damage to garage door, rest garage door opener rail on 2x4 placed on top section of door.

Rail

2x4 is used to determine Door the correct mounting height

from ceiling.

ONE-PIECEDOOR WITHOUT TRACK

A 2x4 on its side is convenient for setting an ideal door-to-raildistance.

ïRemove foam packaging.

ïRaise the opener onto a stepladder. You will need help at this point if the ladder is not tall enough.

ïOpen the door all the way and place a 2x4 on its side on the top section of the door beneath the rail.

ïThe top of the door should be level with the top of the motor unit. Do not position the opener more than 4" (10 cm) above this point.

Header

Bracket

Top of Door

2x4 is used to determine the correct mounting height from ceiling.

11

INSTALLATION STEP 5

Hang the Opener

Three representative installations are shown. Yours may be different. Hanging brackets should be angled (Figure 1) to provide rigid support. On finished ceilings (Figure 2 and Figure 3), attach a sturdy metal bracket to structural supports before installing the opener. This bracket and fastening hardware are not provided.

1.Measure the distance from each side of the motor unit to the structural support.

2.Cut both pieces of the hanging bracket to required lengths.

3.Drill 3/16" pilot holes in the structural supports.

4.Attach one end of each bracket to a support with 5/16"-18x1-7/8"lag screws.

5.Fasten the opener to the hanging brackets with 5/16"-18x7/8"hex bolts, lock washers and nuts.

6.Check to make sure the rail is centered over the door (or in line with the header bracket if the bracket is not centered above the door).

7.Remove the 2x4. Operate the door manually. If the door hits the rail, raise the header bracket.

8.Grease the top and underside of the rail surface where the trolley slides with rail grease.

NOTE: DO NOT connect power to opener at this time.

HARDWARE SHOWN ACTUAL SIZE

Lag Screw 5/16"-18x1-7/8"

Hex Bolt

 

 

5/16"-18x7/8"

Nut 5/16"-18

Lock Washer 5/16"

WARNING

To avoid possible SERIOUS INJURY from a falling garage door opener, fasten it SECURELY to structural supports of the garage. Concrete anchors MUST be used if installing any brackets into masonry.

Figure 1

 

Structural

 

Supports

Measure

Lag Screws

Distance

5/16"-18x1-7/8"

Bolt 5/16"-18x7/8"

 

Lock Washer 5/16"

 

Nut 5/16"-18

 

Figure 2

Hidden

Support

Bracket

(Not Provided)

FINISHED CEILING

Lag Screws 5/16"-18x1-7/8"

(Not Provided)

Bolt 5/16"-18x7/8"

Lock Washer 5/16"

Bolt 5/16"-18x7/8"Nut 5/16"-18

Lock Washer 5/16"

Nut 5/16"-18

Figure 3

Lag Screws 5/16"-18x1-7/8"

FINISHED CEILING

(Not Provided)

Bolt 5/16"-18x7/8"

Lock Washer 5/16"

Bolt 5/16"-18x7/8"Nut 5/16"-18

Lock Washer 5/16"

Nut 5/16"-18

12

INSTALLATION STEP 6

Install the Door Control

Locate door control within sight of the door at a minimum height of 5 feet (1.5 m) where small children cannot reach, and away from moving parts of the door and door hardware. The installation surface must be smooth and flat. If installing into drywall (Figure 1), drill 5/32" holes and use anchors provided. For pre-wiredinstallations (as in new home construction), it may be mounted to a single gang box (Figure 2).

NOTE: After installation, a green indicator light behind the cover will indicate proper connection. If not lit, the Lock and Light features will not function (reverse wires to correct).

1.Strip 7/16" (11 mm) of insulation from one end of bell wire and connect to the two screw terminals on back of door control by color: white wire to 2 and white/red wire to the 1 (Figure 3).

2.Remove white cover by gently prying at slot in top of the cover with a small flat head screwdriver (Figure 4). Fasten with 6ABx1-1/4"self-tappingscrews (drywall installation) or6-32x1"machine screws (into gang box) as follows:

ïDrill and install bottom screw, allowing 1/8" (3 mm) to protrude above wall surface.

ïPosition bottom of door control on screw head and slide down to secure. Adjust screw for snug fit.

ïInstall top screw with care to avoid cracking plastic housing. Do not overtighten.

WARNING

To prevent possible SERIOUS INJURY or DEATH from electrocution:

Be sure power is not connected BEFORE installing door control.

Connect ONLY to 24 VOLT low voltage wires.

To prevent possible SERIOUS INJURY or DEATH from a closing garage door:

Install door control within sight of garage door, out of reach of children at a minimum height of 5 feet (1.5 m), and away from all moving parts of door.

NEVER permit children to operate or play with door control push buttons or remote control transmitters.

Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.

ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door.

HARDWARE SHOWN ACTUAL SIZE

 

Screw 6ABx1-1/4"

 

Insulated

 

(std installation)

 

Staples

Screw 6-32x1"

 

 

(pre-wired)

 

Drywall Anchors

Figure 1

STANDARD

Figure 2

PRE-WIRED

INSTALLATION

INSTALLATION

ï Insert bottom tabs and snap on cover.

NOTE: The push bar may stick if the door control is not mounted on a smooth surface. If a click is not heard when pressing the push bar, loosen the two mounting screws or relocate the door control to a smoother surface.

3.(Standard installation only) Run bell wire up wall and across ceiling to motor unit. Use insulated staples to secure wire in several places. Do not pierce wire with a staple, creating a short or open circuit.

4.Strip 7/16" (11 mm) of insulation from end of bell wire. Connect bell wire to the quick-connectterminals as follows: white to white and white/red to red (Figure 5).

NOTE: When connecting multiple door controls to the opener, twist same color wires together. Insert wires intoquick-connectholes: white to white and red/white to red.

5.Use tacks or staples to permanently attach entrapment warning label to wall near door control, and manual release/safety reverse test label in a prominent location on inside of garage door.

NOTE: DO NOT connect the power and operate the opener at this time. The trolley will travel to the full open position but will not return to the close position until the sensor beam is connected and properly aligned. See Safety Reversing Sensor Instructions beginning on page 16.

Single

Gang Box

LOCK

 

 

 

LIGHT

 

LOCK

 

To Replace

 

LIGHT

 

 

 

24 Volt

Insert Bottom Tabs First

To Replace

 

 

Bell Wire

 

Insert Bottom Tabs First

 

 

Figure 3 MULTI-FUNCTION

Figure 4 REMOVE COVER

DOOR CONTROL (BACK)

 

 

 

 

Slot

 

Top Mounting Hole

 

 

 

Terminal

 

 

 

Screws

 

 

 

 

 

 

LOCK

Bell Wire

 

 

LIGHT

 

 

 

Bottom Mounting Hole

 

 

Figure 5

 

 

 

Door Control

To release wire, push in tab

Connections

with screwdriver tip

Red White Grey

7/16" (11 mm)

Strip wire 7/16" (11 mm)

13

INSTALLATION STEP 7

Install the Light

ïPress the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is in the fully open position. Do not remove the lens.

ïInstall up to a 100 watt maximum light bulb in each socket. The light will turn ON and remain lit for approximately 4-1/2minutes when power is connected. Then the lights will turn OFF.

ïReverse the procedure to close the lens.

ïIf the bulbs burn out prematurely due to vibration, replace with a Garage Door Opener bulb.

NOTE: Use only standard light bulbs. The use of short neck or speciality light bulbs may overheat the endpanel or light socket.

CAUTION

To prevent possible OVERHEATING of the endpanel or light socket,

DO NOT use short neck or specialty light bulbs.

DO NOT use halogen bulbs. Use ONLY incandescent.

100 Watt (Max)

Standard Light Bulb

Release Tab

Lens Hinge

INSTALLATION STEP 8

Attach the Emergency Release

Rope and Handle

ïThread one end of the rope through the hole in the top of the red handle so ìNOTICEî reads right side up as shown. Secure with an overhand knot at least 1" (2.5 cm) from the end of the rope to prevent slipping.

ïThread the other end of the rope through the hole in the release arm of the outer trolley.

ïAdjust rope length so the handle is 6 feet (1.83 m) above the floor. Ensure that the rope and handle clear the tops of all vehicles to avoid entanglement. Secure with an overhand knot.

NOTE: If it is necessary to cut the rope, heat seal the cut end with a match or lighter to prevent unraveling.

WARNING

To prevent possible SERIOUS INJURY or DEATH from a falling garage door:

If possible, use emergency release handle to disengage trolley ONLY when garage door is

CLOSED. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly.

NEVER use emergency release handle unless garage doorway is clear of persons and obstructions.

NEVER use handle to pull door open or closed. If rope knot becomes untied, you could fall.

Trolley

Rope

NOTICE

Overhand

Knot

Trolley

Release Arm

Emergency

Release Handle

14

INSTALLATION STEP 9

Electrical Requirements

To avoid installation difficulties, do not run the opener at this time.

To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesnít fit into the outlet you have, contact a qualified electrician to install the proper outlet.

WARNING

To prevent possible SERIOUS INJURY or DEATH from electrocution or fire:

Be sure power is not connected to the opener, and disconnect power to circuit BEFORE removing cover to establish permanent wiring connection.

Garage door installation and wiring MUST be in compliance with all local electrical and building codes.

NEVER use an extension cord, 2-wireadapter, or change plug in ANY way to make it fit outlet. Be sure the opener is grounded.

RIGHT

WRONG

If permanent wiring is required by your local code, refer to the following procedure.

To make a permanent connection through the 7/8" hole in the top of the motor unit:

ïRemove the motor unit cover screws and set the cover aside.

ïRemove the attached 3-prongcord.

ïConnect the black (line) wire to the screw on the brass terminal; the white (neutral) wire to the screw on the silver terminal; and the ground wire to the green ground screw. The opener must be grounded.

ïReinstall the cover.

To avoid installation difficulties, do not run the opener at this time.

PERMANENT WIRING

CONNECTION

Ground Tab

Green

Ground Screw

Ground Wire

Black

Wire

White Wire

Black Wire

15

INSTALLATION STEP 10

Install The Protector System®

The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction.

IMPORTANT INFORMATION ABOUT

THE SAFETY REVERSING SENSOR

When properly connected and aligned, the sensor will detect an obstacle in the path of its electronic beam. The sending eye (with an amber indicator light) transmits an invisible light beam to the receiving eye (with a green indicator light). If an obstruction breaks the light beam while the door is closing, the door will stop and reverse to full open position, and the opener lights will flash 10 times.

The units must be installed inside the garage so that the sending and receiving eyes face each other across the door, no more than 6" (15 cm) above the floor. Either can be installed on the left or right of the door as long as the sun never shines directly into the receiving eye lens.

The mounting brackets are designed to clip onto the track of sectional garage doors without additional hardware.

WARNING

Be sure power is not connected to the garage door opener BEFORE installing the safety reversing sensor.

To prevent SERIOUS INJURY or DEATH from a closing garage door:

Correctly connect and align the safety reversing sensor. This required safety device MUST NOT be disabled.

Install the safety reversing sensor so beam is NO

HIGHER than 6" (15 cm) above garage floor.

If it is necessary to mount the units on the wall, the brackets must be securely fastened to a solid surface such as the wall framing. Extension brackets (see accessories) are available if needed. If installing in masonry construction, add a piece of wood at each location to avoid drilling extra holes in masonry if repositioning is necessary.

The invisible light beam path must be unobstructed. No part of the garage door (or door tracks, springs, hinges, rollers or other hardware) may interrupt the beam while the door is closing.

Sensor Beam

Invisible Light Beam

Sensor Beam

6" (15 cm) max.

6" (15 cm) max.

Protection Area

above floor

above floor

 

Facing the door from inside the garage

16

INSTALLING THE BRACKETS

Be sure power to the opener is disconnected.

Install and align the brackets so the sensors will face each other across the garage door, with the beam no higher than 6" (15 cm) above the floor. They may be installed in one of three ways, as follows.

Garage door track installation (preferred):

ïSlip the curved arms over the rounded edge of each door track, with the curved arms facing the door. Snap into place against the side of the track. It should lie flush, with the lip hugging the back edge of the track, as shown in Figure 1.

If your door track will not support the bracket securely, wall installation is recommended.

Wall installation (Figure 2 & 3):

ïPlace the bracket against the wall with curved arms facing the door. Be sure there is enough clearance for the sensor beam to be unobstructed.

ïIf additional depth is needed, an extension bracket (See accessories) or wood blocks can be used.

ïUse bracket mounting holes as a template to locate and drill (2) 3/16" diameter pilot holes on the wall at each side of the door, no higher than 6"

(15 cm) above the floor.

ïAttach brackets to wall with lag screws (Not provided).

ïIf using extension brackets or wood blocks, adjust right and left assemblies to the same distance out from the mounting surface. Make sure all door hardware obstructions are cleared.

Floor installation (Figure 4):

ïUse wood blocks or extension brackets (see accessories) to elevate sensor brackets so the lenses will be no higher than 6" (15 cm) above the floor.

ïCarefully measure and place right and left assemblies at the same distance out from the wall. Be sure all door hardware obstructions are cleared.

ïFasten to the floor with concrete anchors as shown.

HARDWARE SHOWN ACTUAL SIZE

Carriage Bolt

Wing Nut

Staples

1/4"-20x1/2"

1/4"-20

 

Figure 1

DOOR TRACK MOUNT (RIGHT SIDE)

Door

Track

Lip

Indicator

Light

Sensor

Bracket

Lens

Figure 2

Inside

Garage

Wall

WALL MOUNT (RIGHT SIDE)

Fasten Wood Block to Wall with Lag Screws (Not Provided)

Indicator

Light Sensor

Bracket

Lag Screws

(Not Provided)

Lens

Figure 3

WALL MOUNT (RIGHT SIDE)

Inside

Garage

Wall

(Provided with Extension Bracket)

Figure 4

Extension

Bracket

(See Accessories)

(Provided with Extension Bracket)

Sensor

Bracket

Indicator

Lens Light

FLOOR MOUNT (RIGHT SIDE)

Inside

Attach with

Concrete Anchors

Garage

(Not Provided)

all

 

W

 

 

Lens

 

Indicator

 

Light

 

Sensor

 

Bracket

17

MOUNTING AND WIRING THE SAFETY SENSORS

ïSlide a 1/4"-20x1/2"carriage bolt head into the slot on each sensor. Use wing nuts to fasten sensors to brackets, with lenses pointing toward each other across the door. Be sure the lens is not obstructed by a bracket extension (Figure 5).

ïFinger tighten the wing nuts.

ïRun the wires from both sensors to the opener. Use insulated staples to secure wire to wall and ceiling.

ïStrip 7/16" (11 mm) of insulation from each set of wires. Separate white and white/black wires sufficiently to connect to the opener quick-connectterminals. Twist like colored wires together. Insert wires intoquick-connectholes: white to white and white/black to grey (Figure 6).

ALIGNING THE SAFETY SENSORS

ïPlug in the opener. The indicator lights in both the sending andreceiving eyes willglow steadily if wiring connections and alignment are correct.

The sending eye amber indicator light will glow regardless of alignment or obstruction. If the green indicator light in thereceiving eye is off, dim, or flickering (and the invisible light beam path is not obstructed), alignment is required.

ïLoosen the sending eye wing nut and readjust, aiming directly at the receiving eye. Lock in place.

ïLoosen the receiving eye wing nut and adjust sensor until it receives the senderís beam. When the green indicator lightglows steadily, tighten the wing nut.

Figure 6

Figure 5

Wing Nut

Carriage Bolt

1/4"-20x1/2"

Lens

TROUBLESHOOTING THE SAFETY SENSORS

1.If the sending eye indicator light does notglow steadily after installation, check for:

ïElectric power to the opener.

ïA short in the white or white/black wires. These can occur at staples, or at opener connections.

ïIncorrect wiring between sensors and opener.

ïA broken wire.

2.If the sending eye indicator lightglows steadily but thereceiving eye indicator light doesnít:

ïCheck alignment.

ïCheck for an open wire to the receiving eye.

3.If the receiving eye indicator light is dim, realign either sensor.

NOTE: When the invisible beam path is obstructed or misaligned while the door is closing, the door will reverse. If the door is already open, it will not close. The opener lights will blink 10 times. See page 16.

Connect Wire to

Opener Quick-ConnectTerminals

Bell Wire

Finished

Ceiling

 

1.

Strip wire 7/16"

Bell Wire

(11 mm)

 

7/16" (11 mm)

2. Twist like colored wires together

3. Insert into appropriate terminals

Red White Grey

Quick-ConnectTerminals

Sensor

 

Invisible Light Beam

Sensor

Protection Area

18

INSTALLATION STEP 11

Fasten the Door Bracket

Follow instructions which apply to your door type as illustrated below or on the following page.

A horizontal reinforcement brace should be long enough to be secured to two or three vertical supports. A vertical reinforcement brace should cover the height of the top panel.

Figure 1 shows one piece of angle iron as the horizontal brace. For the vertical brace, 2 pieces of angle iron are used to create a U-shapedsupport. The best solution is to check with your garage door manufacturer for an opener installation door reinforcement kit.

NOTE: Many door reinforcement kits provide for direct attachment of the clevis pin and door arm. In this case you will not need the door bracket; proceed to Step 12.

SECTIONAL DOORS

1.Center the door bracket on the previously marked vertical centerline used for the header bracket installation. Note correct UP placement, as stamped inside the bracket.

2.Position the top edge of the bracket 2"-4"(5-10cm) below the top edge of the door, OR

directly below any structural support across the top of the door.

3.Mark, drill holes and install as follows, depending on your doorís construction:

Metal or light weight doors using a vertical angle iron brace between the door panel support and the door bracket:

ïDrill 3/16" fastening holes. Secure the door bracket using the two 1/4"-14x5/8"self-threadingscrews. (Figure 2A)

ïAlternately, use two 5/16" bolts, lock washers and nuts (not provided). (Figure 2B)

Metal, insulated or light weight factory reinforced doors:

ïDrill 3/16" fastening holes. Secure the door bracket using the self-threadingscrews. (Figure 3)

Wood Doors:

ïUse top and bottom or side to side door bracket holes. Drill 5/16" holes through the door and secure bracket with 5/16"x2" carriage bolts, lock washers and nuts (not provided). (Figure 4)

NOTE: The1/4"-14x5/8"

HARDWARE

self-threadingscrews are

SHOWN

not intended for use on

ACTUAL SIZE

wood doors.

Self-Threading

 

 

Screw

 

1/4"-14x5/8"

CAUTION

Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door bracket. Contact your door manufacturer for reinforcement kit.

Header

Bracket

Door

Bracket

Location

 

HORIZONTAL AND VERTICAL

 

REINFORCEMENT IS NEEDED

Vertical

FOR LIGHTWEIGHT GARAGE

Centerline

DOORS (FIBERGLASS,

of Garage

ALUMINUM, STEEL, DOORS

Door

WITH GLASS PANEL, ETC.).

 

(NOT PROVIDED)

Figure 1

 

 

Vertical

 

 

(Not Provided)

Reinforcement

Vertical

 

 

Vertical

Reinforcement

 

 

Centerline

 

 

 

of Garage Door

Vertical

Bolt

 

 

Centerline

 

 

5/16"-18x2"

 

 

of Garage Door

 

 

 

 

 

 

 

 

UP

 

Door

 

 

UP

Bracket

 

Door

Lock Washer

5/16"

Nut

Bracket

 

 

 

 

5/16"-18

Self-Threading

 

 

 

 

 

Screw

 

 

Figure 2B

1/4"-14x5/8"

 

 

Figure 2A

(Not Provided)

Inside Edge

of Door or

 

 

 

 

Reinforcement Board

 

Bolt

 

 

5/16"x2"

 

 

 

UP

Vertical

 

 

Centerline

 

 

of Garage Door

Vertical

 

 

 

UP

Centerline

 

of Garage

 

 

 

 

Door

 

Self-Threading

 

Figure 4

Screw

 

 

1/4"-14x5/8"

 

 

Figure 3

19

ONE-PIECEDOORS

Please read and comply with the warnings and reinforcement instructions on the previous page. They apply to one-piecedoors also.

ïCenter the door bracket on the top of the door, in line with the header bracket as shown. Mark either the left and right, or the top and bottom holes.

ïMetal Doors: Drill 3/16" pilot holes and fasten the bracket with the1/4"-14x5/8"self-threadingscrews provided.

ïWood Doors: Drill 5/16" holes and use 5/16"x2" carriage bolts, lock washers and nuts (not provided) or5/16"x1-1/2"lag screws (not provided) depending on your installation needs.

NOTE: The door bracket may be installed on the top edge of the door if required for your installation. (Refer to the dotted line optional placement drawing.)

HARDWARE SHOWN

ACTUAL SIZE

Self-ThreadingScrew1/4"-14x5/8"

 

 

 

 

Self-Threading

 

 

 

 

Screw

 

 

 

Door

1/4"-14x5/8"

Header Wall

 

Finished Ceiling

Top of Door

 

Bracket

 

2x4 Support

(Inside

 

 

 

 

 

 

 

Garage)

 

 

 

 

Top Edge

 

 

 

 

of Door

Header

 

 

 

 

Bracket

 

 

 

 

 

 

 

 

Optional

 

 

 

 

Placement

Door

 

 

 

 

Bracket

 

 

 

 

Optional

Placement

of Door

Bracket

Vertical

Centerline of

Garage Door

 

 

METAL DOOR

HORIZONTAL AND VERTICAL

 

 

REINFORCEMENT IS NEEDED

Nut

Lock

FOR LIGHTWEIGHT GARAGE

5/16"-18

DOORS (FIBERGLASS,

 

Washer

ALUMINUM, STEEL, DOORS

 

5/16"

WITH GLASS PANEL, ETC.).

Door

Top of Door

(NOT PROVIDED)

Bracket

(Inside

 

 

 

Garage)

 

 

Top Edge

 

 

of Door

 

 

Optional

 

 

Placement

 

 

Carriage Bolt

 

 

5/16"x2"

 

 

(Not Provided)

For a door with no exposed framing,

 

WOOD DOOR

or for the optional installation, use

 

 

lag screws 5/16"x1-1/2"(Not Provided)

 

to fasten door bracket.

 

 

20

INSTALLATION STEP 12

Connect Door Arm to Trolley

Follow instructions which apply to your door type as illustrated below and on the following page.

SECTIONAL DOORS ONLY

ïMake sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley. Slide the outer trolley back (away from the door) about 2" (5 cm) as shown in Figures 1, 2 and 3.

Figure 1:

ñFasten straight door arm section to outer trolley with the 5/16"x1" clevis pin. Secure the connection with a ring fastener.

ñFasten curved section to the door bracket in the same way, using the 5/16"x1-1/4"clevis pin.

Figure 2:

ñBring arm sections together. Find two pairs of holes that line up and join sections. Select holes as far apart as possible to increase door arm rigidity.

Figure 3, Hole alignment alternative:

ñIf holes in curved arm are above holes in straight arm, disconnect straight arm. Cut about 6"

(15 cm) from the solid end. Reconnect to trolley with cut end down as shown.

ñBring arm sections together.

ñFind two pairs of holes that line up and join with bolts, lock washers and nuts.

ïPull the emergency release handle toward the opener at a 45 angle so that the trolley release arm is horizontal. Proceed to Adjustment Step 1, page 23. Trolley will re-engageautomatically when opener is operated.

HARDWARE SHOWN ACTUAL SIZE

 

Nut 5/16"-18

Lock Washer 5/16"

Ring Fastener

 

Clevis Pin

Clevis Pin

 

Hex Bolt

5/16"x1" (Trolley)

5/16"x1-1/4"(Door Bracket)

5/16"-18x7/8"

Inner Trolley

Outer Trolley

Clevis Pin

Ring 5/16"x1"

Fastener

Emergency

Release

Door Handle

Bracket

Straight

Door Arm

Curved

Door Arm

Clevis Pin

5/16"x1-1/4"

Figure 1

Lock Washers 5/16"

Nuts 5/16"-18

Bolts 5/16"-18x7/8"

Door Bracket

Figure 2

Lock Washers 5/16"

Nuts 5/16"-18

Bolts 5/16"-18x7/8"

Cut This End

Figure 3

21

ALL ONE-PIECEDOORS

1.Assemble the door arm, Figure 4:

ïFasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap).

ïWith the door closed, connect the straight door arm section to the door bracket with the 5/16"x1-1/4"clevis pin.

ïSecure with a ring fastener.

2.Adjustment procedures, Figure 5:

ïOn one-piecedoors, before connecting the door arm to the trolley, the travel limits must be adjusted. Limit adjustment screws are located on the left side panel as shown on page 23. Follow adjustment procedures below.

ïOpen door adjustment: decrease UP travel limit

-Turn the UP limit adjustment screw counter-clockwise4 turns.

-Press the Door Control push button. The trolley will travel to the fully open position.

-Manually raise the door to the open position (parallel to the floor), and lift the door arm to the trolley. The arm should touch the trolley just in back of the door arm connector hole. Refer to the fully open trolley/door arm positions in the illustration. If the arm does not extend far enough, adjust the limit further. One full turn equals 2" (5 cm) of trolley travel.

ïClosed door adjustment: decrease DOWN travel limit

-Turn the DOWN limit adjustment screw clockwise 4 complete turns.

Door

Ring

 

Bracket

 

 

Fastener

Nuts

 

Lock

 

5/16"-18

 

Washers

 

Clevis Pin

5/16"

 

Straight

 

5/16"x1-1/4"

Arm

 

 

Bolts

Curved

Figure 4

5/16"-18x7/8

Door Arm

 

-Press the Door Control push button. The trolley will travel to the fully closed position.

-Manually close the door and lift the door arm to the trolley. The arm should touch the trolley just ahead of the door arm connector hole. Refer to the fully closed trolley/door arm positions in the illustration. If the arm is behind the connector hole, adjust the limit further. One full turn equals 2" (5 cm) of trolley travel.

3.Connect the door arm to the trolley:

ïClose the door and join the curved arm to the connector hole in the trolley with the remaining clevis pin. It may be necessary to lift the door slightly to make the connection.

ïSecure with a ring fastener.

ïRun the opener through a complete travel cycle. If the door has a slight "backward" slant in full open position as shown in the illustration, decrease the UP limit until the door is parallel to the floor.

NOTE: When setting the up limit on the following page, the door should not have a "backward" slant when fully open as illustrated below. A slight backward slant will cause unnecessary bucking and/or jerking operation as the door is being opened or closed from the fully open position.

Figure 5

Inner Trolley

Outer Trolley

Door Arm

Connector Hole

Door Arm

Emergency Release Handle

Closed

Door

Inner Trolley

 

 

Outer Trolley

 

Correct Angle

Door Arm

 

 

 

 

Door with

Open Door

 

Backward Slant (Incorrect)

22

ADJUSTMENT STEP 1

Adjust the UP and DOWN Travel

Limits

Limit adjustment settings regulate the points at which the door will stop when moving up or down.

To operate the opener, press the Door Control push bar. Run the opener through a complete travel cycle.

ïDoes the door open and close completely?

ïDoes the door stay closed and not reverse unintentionally when fully closed?

If your door passes both of these tests, no limit adjustments are necessary unless the reversing test fails (Adjustment Step 3, page 25).

Adjustment procedures are outlined below. Read the procedures carefully before proceeding to Adjustment Step 2. Use a screwdriver to make limit adjustments. Run the opener through a complete travel cycle after each adjustment.

NOTE: Repeated operation of the opener during adjustment procedures may cause the motor to overheat and shut off. Simply wait 15 minutes and try again.

NOTE: If anything interferes with the door’s upward travel, it will stop. If anything interferes with the door’s downward travel (including binding or unbalanced doors), it will reverse.

HOW AND WHEN TO ADJUST THE LIMITS

If the door does not open completely but opens at least five feet (1.5 m):

Increase up travel. Turn the UP limit adjustment screw clockwise. One turn equals 2" (5 cm) of travel.

NOTE: To prevent the trolley from hitting the cover protection bolt, keep a minimum distance of2-4"(5 cm - 10 cm) between the trolley and the bolt.

If door does not open at least 5 feet (1.5 m):

Adjust the UP (open) force as explained in Adjustment Step 2.

If the door does not close completely:

Increase down travel. Turn the down limit adjustment screw counterclockwise. One turn equals 2" (5 cm) of travel.

If door still won't close completely and the trolley bumps into the pulley bracket (page 4), try lengthening the door arm (page 21) and decreasing the down limit.

If the opener reverses in fully closed position:

Decrease down travel. Turn the down limit adjustment screw clockwise. One turn equals 2" (5 cm) of travel.

WARNING

Without a properly installed safety reversal system, persons (particularly small children) could be

SERIOUSLY INJURED or KILLED by a closing garage door.

Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system.

If one control (force or travel limits) is adjusted, the other control may also need adjustment.

After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with 1-1/2"high (3.8 cm) object (or 2x4 laid flat) on floor.

CAUTION

To prevent damage to vehicles, be sure fully open door provides adequate clearance.

Cover Protection

Bolt

2-4"

(5-10cm)

Left Side Panel

Limit Adjustment Screws

 

 

 

 

 

 

Adjustment Label

If the door reverses when closing and there is no visible interference to travel cycle:

If the opener lights are flashing, the Safety Reversing Sensors are either not installed, misaligned, or obstructed. See Troubleshooting, page 18.

Test the door for binding: Pull the emergency release handle. Manually open and close the door. If the door is binding or unbalanced, call for a trained door systems technician. If the door is balanced and not binding, adjust the DOWN (close) force. See Adjustment Step 2.

23

ADJUSTMENT STEP 2

Adjust the Force

Force adjustment controls are located on the back panel of the motor unit. Force adjustment settings regulate the amount of power required to open and close the door.

If the forces are set too light, door travel may be interrupted by nuisance reversals in the down direction and stops in the up direction. Weather conditions can affect the door movement, so occasional adjustment may be needed.

The maximum force adjustment range is about 3/4 of a complete turn. Do not force controls beyond that point. Turn force adjustment controls with a screwdriver.

NOTE: If anything interferes with the door’s upward travel, it will stop. If anything interferes with the door’s downward travel (including binding or unbalanced doors), it will reverse.

HOW AND WHEN TO ADJUST THE FORCES

1. Test the DOWN (close) force

ïGrasp the door bottom when the door is about halfway through DOWN (close) travel. The door should reverse. Reversal halfway through down travel does not guarantee reversal on a 1-1/2" (3.8 cm) obstruction. See Adjustment Step 3, page 25. If the door is hard to hold or doesnít reverse, DECREASE the DOWN (close) force by turning the control counterclockwise. Make small adjustments until the door reverses normally. After each adjustment, run the opener through a complete cycle.

ïIf the door reverses during the down (close) cycle and the opener lights arenít flashing,

INCREASE DOWN (close) force by turning the control clockwise. Make small adjustments until the door completes a close cycle. After each adjustment, run the opener through a complete travel cycle. Do not increase the force beyond the minimum amount required to close the door.

2. Test the UP (open) force

ïGrasp the door bottom when the door is about halfway through UP (open) travel. The door should stop. If the door is hard to hold or doesnít stop,

DECREASE UP (open) force by turning the control counterclockwise. Make small adjustments until the door stops easily and opens fully. After each adjustment, run the opener through a complete travel cycle.

ïIf the door doesnít open at least 5 feet (1.5 m),

INCREASE UP (open) force by turning the control clockwise. Make small adjustments until door opens completely. Readjust the UP limit if necessary. After each adjustment, run the opener through a complete travel cycle.

WARNING

Without a properly installed safety reversal system, persons (particularly small children) could be

SERIOUSLY INJURED or KILLED by a closing garage door.

Too much force on garage door will interfere with proper operation of safety reversal system.

NEVER increase force beyond minimum amount required to close garage door.

NEVER use force adjustments to compensate for a binding or sticking garage door.

If one control (force or travel limits) is adjusted, the other control may also need adjustment.

After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with 1-1/2"high (3.8 cm) object (or 2x4 laid flat) on floor.

Force

Adjustment

Controls

Back Panel

KG

KG

Antenna

FORCE ADJUSTMENT LABEL

9

 

1

9

1

7

3

 

7

3

 

5

 

5

 

 

KG

 

KG

 

 

 

 

 

Open Force

 

Close Force

 

24

ADJUSTMENT STEP 3

Test the Safety Reversal System

TEST

ïWith the door fully open, place a 1-1/2"(3.8 cm) board (or a 2x4 laid flat) on the floor, centered under the garage door.

ïOperate the door in the down direction. The door must reverse on striking the obstruction.

ADJUST

ïIf the door stops on the obstruction, it is not traveling far enough in the down direction. Increase the DOWN limit by turning the DOWN limit adjustment screw counterclockwise 1/4 turn.

NOTE: On a sectional door, make sure limit adjustments do not force the door arm beyond a straight up and down position. See the illustration on page 21.

ïRepeat the test.

ïWhen the door reverses on the 1-1/2"(3.8 cm) board, remove the obstruction and run the opener through 3 or 4 complete travel cycles to test adjustment.

ïIf the unit continues to fail the Safety Reverse Test, call for a trained door systems technician.

IMPORTANT SAFETY CHECK:

Test the Safety Reverse System after:

ïEach adjustment of door arm length, limits, or force controls.

ïAny repair to or adjustment of the garage door (including springs and hardware).

ïAny repair to or buckling of the garage floor.

ïAny repair to or adjustment of the opener.

ADJUSTMENT STEP 4

Test The Protector System®

ïPress the remote control push button to open the door.

ïPlace the opener carton in the path of the door.

ïPress the remote control push button to close the door. The door will not move more than an inch (2.5 cm), and the opener lights will flash.

The garage door opener will not close from a remote if the indicator light in either sensor is off (alerting you to the fact that the sensor is misaligned or obstructed).

If the opener closes the door when the safety reversing sensor is obstructed (and the sensors are no more than 6" (15 cm) above the floor), call for a trained door systems technician.

WARNING

Without a properly installed safety reversal system, persons (particularly small children) could be

SERIOUSLY INJURED or KILLED by a closing garage door.

Safety reversal system MUST be tested every month.

If one control (force or travel limits) is adjusted, the other control may also need adjustment.

After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with 1-1/2"high (3.8 cm) object (or 2x4 laid flat) on the floor.

1-1/2"(3.8 cm) board (or a 2x4 laid flat)

WARNING

Without a properly installed safety reversing sensor, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door.

Safety Reversing Sensor

Safety Reversing Sensor

25

OPERATION

IMPORTANT SAFETY INSTRUCTIONS

WARNING

To reduce the risk of SEVERE INJURY or DEATH:

1.READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS.

2.ALWAYS keep remote controls out of reach of children.

NEVER permit children to operate or play with garage door control push buttons or remote controls.

3.ONLY activate garage door when it can be seen clearly, it is properly adjusted, and there are no obstructions to door travel.

4.ALWAYS keep garage door in sight until completely closed. NO ONE SHOULD CROSS THE PATH OF THE

MOVING DOOR.

5.NO ONE SHOULD GO UNDER A STOPPED, PARTIALLY OPEN DOOR.

6.If possible, use emergency release handle to disengage trolley ONLY when garage door is CLOSED. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly.

7.NEVER use emergency release handle unless garage doorway is clear of persons and obstructions.

8.NEVER use handle to pull garage door open or closed.

If rope knot becomes untied, you could fall.

9.If one control (force or travel limits) is adjusted, the other control may also need adjustment.

10.After ANY adjustments are made, the safety reversal system MUST be tested.

11.Safety reversal system MUST be tested every month.

Garage door MUST reverse on contact with 1-1/2"high

(3.8 cm) high object (or a 2x4 laid flat) on the floor.

12.ALWAYS KEEP GARAGE DOOR PROPERLY BALANCED

(see page 3). An improperly balanced door may not reverse when required and could result in SEVERE

INJURY or DEATH.

13.All repairs to cables, spring assemblies and other hardware, all of which are under EXTREME tension, MUST be made by a trained door systems technician.

14.ALWAYS disconnect electric power to garage door opener BEFORE making any repairs or removing covers.

15. SAVE THESE INSTRUCTIONS.

Using Your Garage Door Opener

Your Security Æ opener andhand-heldremote control have beenfactory-setto a matching code which changes with each use, randomly accessing over 100 billion new codes. Your opener will operate with up to eight SecurityÆ remote controls and one SecurityÆ Keyless Entry System. If you purchase a new remote, or if you wish to deactivate any remote, follow the instructions in theProgramming section.

Activate your opener with any of the following:

ïThe hand-heldRemote Control:Hold the large push button down until the door starts to move.

ïThe wall-mountedDoor Control:Hold the push button or bar down until the door starts to move.

ïThe Keyless Entry (See Accessories): If provided with your garage door opener, it must be programmed before use. See Programming.

When the opener is activated (with the safety reversing sensor correctly installed and aligned)

1.If open, the door will close. If closed, it will open.

2.If closing, the door will reverse.

3.If opening, the door will stop.

4.If the door has been stopped in a partially open position, it will close.

5.If obstructed while closing, the door will reverse. If the obstruction interrupts the sensor beam, the opener lights will blink for five seconds.

6.If obstructed while opening, the door will stop.

7.If fully open, the door will not close when the beam is broken. The sensor has no effect in the opening cycle.

If the sensor is not installed, or is misaligned, the door wonít close from a hand-heldremote. However, you can close the door with the Door Control, the Outside Keylock, or Keyless Entry,if you activate them until down travel is complete. If you release them too soon, the door will reverse.

The opener lights will turn on under the following conditions: when the opener is initially plugged in; when power is restored after interruption; when the opener is activated.

They will turn off automatically after 4-1/2minutes or provide constant light when the Light feature on theMulti-FunctionDoor Control is activated. Bulb size is 100 watts maximum.

Security ®light feature: Lights will also turn on when someone walks through the open garage door. With aMulti-FunctionDoor Control, this feature may be turned off as follows: With the opener lights off, press and hold the light button for 10 seconds, until the light goes on, then off again. To restore this feature, start with the opener lights on, then press and hold the light button for 10 seconds until the light goes off, then on again.

26

Open Close
Stop

Using the Wall-Mounted

Door Control

THE MULTI-FUNCTIONDOOR CONTROL

Press the push bar to open or close

the door. Press again to reverse the

 

Push

 

Button

door during the closing cycle or to

 

Lock

stop the door while it's opening.

 

 

Button

Light feature

 

LIGHT

Light

 

LOCK

 

 

 

Button

Press the Light button to turn the

opener light on or off. It will not control the opener lights when the door is in motion. If you turn it on and then activate the opener, the light will remain on for 4-1/2minutes. Press again to turn it off sooner. The4-1/2minute interval can be changed to1-1/2,2-1/2,or3-1/2minutes as follows: Press and hold the Lock button until the light blinks (about 10 seconds). A single blink indicates that the timer is reset to1-1/2minutes. Repeat the procedure and the light will blink twice, resetting the timer to2-1/2minutes. Repeat again for a3-1/2minute interval, etc., up to a maximum of four blinks and4-1/2minutes.

Lock feature

Designed to prevent operation of the door from hand-heldremote controls. However, the door will open and close from the Door Control, the Outside Keylock and the Keyless Entry Accessories.

To activate, press and hold the Lock button for 2 seconds. The push bar light will flash as long as the Lock feature is on.

To turn off, press and hold the Lock button again for 2 seconds.The push bar light will stop flashing. The Lock feature will also turn off whenever the ìLearnî button on the motor unit panel is activated.

Additional features when used with the 3-Channelhand-heldremote

A) To control the opener lights:

In addition to operating the door, you

may program the remote to operate the lights.

1.With the door closed, press and hold a small remote button that you want to control the light.

2.Press and hold the Light button on the Multi-Functiondoor control.

3.While holding the Light button, press and hold the Lock button on the door control.

4.After the opener lights flash, release all buttons.

B)To operate one door using all three buttons on the hand-heldremote:

You may program the remote to open the door with the large button, close it with the middle

button, and stop the doorís movement with the third button.

NOTE: If remote is already programmed, you must first erase all codes. See Programming.

1.With the door closed, press and hold the large remote push button.

2.Press and hold the Lock button on the door control.

3.Press and hold the door control push bar.

4.After the opener lights flash, release all buttons.

To Open the Door Manually

WARNING

To prevent possible SERIOUS INJURY or DEATH from a falling garage door:

If possible, use emergency release handle to disengage trolley ONLY when garage door is CLOSED.

Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly.

NEVER use emergency release handle unless garage doorway is clear of persons and obstructions.

NEVER use handle to pull door open or closed. If rope knot becomes untied, you could fall.

The door should be fully closed if possible. Pull down on the emergency release handle and lift the door manually. To reconnect the door to the opener, press the door control push bar.

Emergency

Release

Handle

(Pull Down)

Trolley

Release

Arm

NOTICE

The lockout featureprevents the trolley from reconnecting automatically. Pull the emergency release handle down and back (toward the opener). The door can then be raised and lowered manually as often as necessary. To disengage the lockout feature, pull the handle straight down. The trolley will reconnect on the next UP or DOWN operation, either manually or by using the door control or remote.

MANUAL DISCONNECT

POSITION

Trolley

Release

Arm

Emergency

Release Handle

(Down and Back)

TICE

NO

LOCKOUT POSITION

27

CARE OF YOUR OPENER

LIMIT AND FORCE ADJUSTMENTS:

Weather conditions may

FORCE CONTROLS

 

cause some minor changes

 

 

 

 

 

 

in door operation requiring

9

1

9

1

 

some re-adjustments,

7

3

7

3

 

particularly during the first

 

5

 

5

 

 

KG

 

KG

 

year of operation.

 

 

 

 

 

 

 

 

 

 

Pages 23 and 24 refer to the LIMIT CONTROLS

 

 

limit and force adjustments.

 

 

 

 

 

 

 

 

 

 

Only a screwdriver is

 

 

 

 

 

required. Follow the

 

 

 

 

 

instructions carefully.

 

 

 

 

 

Repeat the safety reverse test (Adjustment

Step 3, page 25) after any adjustment of limits or force.

MAINTENANCE SCHEDULE

Once a Month

ïManually operate door. If it is unbalanced or binding, call a trained door systems technician.

ïCheck to be sure door opens and closes fully. Adjust limits and/or force if necessary. (See pages 23 and 24.)

ïRepeat the safety reverse test. Make any necessary adjustments. (See Adjustment Step 3.)

Twice a Year

ïCheck chain tension. Disconnect trolley first. Adjust if necessary (See page 7).

Once a Year

ïOil door rollers, bearings and hinges. The opener does not require additional lubrication. Do not grease the door tracks.

THE REMOTE CONTROL BATTERY

WARNING

To prevent possible SERIOUS INJURY or DEATH:

NEVER allow small children near batteries.

If battery is swallowed, immediately notify doctor.

The lithium battery should produce power for up to

5 years. To replace battery, use the visor clip or screwdriver blade to pry

open the case as shown. Insert battery positive side up (+).

Dispose of old battery properly.

Battery positive

side up (+)

NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

28

HAVING A PROBLEM?

1.My door will not close and the light bulbs blink on my motor unit: The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction.

ïVerify the safety sensors are properly installed, aligned and free of any obstructions. Refer to

Installation Step 10: Install The Protector System®.

ïCheck diagnostic LED for flashes on the motor unit then refer to the Diagnostic Chart on the following page.

Bell Wire

"Learn" ButtonLED or Diagnostic

LED

Safety Sensor

2.My remotes will not activate the door:

ïVerify your Door Control is not blinking. If it is blinking, deactivate the Lock Mode following the instructions for Using the Wall-Mounted Door Control.

ïReprogram remotes following the programming instructions. Refer to Programming.

ïIf remote will still not activate your door, check diagnostic LED for flashes on motor unit then refer to Diagnostic Chart on the following page.

3.My door reverses for no apparent reason:

Repeat safety reverse test after adjustments to force or travel limits. The need for occasional adjustment for the force and limit settings is normal. Weather conditions in particular can affect door travel.

ïManually check door for balance or any binding problems.

ïRefer to Adjustment Step 2, Adjust the Force.

4.My door reverses for no apparent reason after fully closing and touching the floor: Repeat safety reverse test after adjustments to force or travel limits. The need for occasional adjustment for the force and limit settings is normal. Weather conditions in particular can affect door travel.

ïRefer to Adjustment Step 1, Adjust the UP and DOWN Travel Limits.Decrease down travel by turning down limit adjustment screw clockwise.

5.My lights will not turn off when door is open:

ïThe garage door opener is equipped with a security light feature. This feature activates the light on when the safety sensor beam has been obstructed. Refer to Operation section; Using the

Wall Mounted Door Control, Light Feature.

Sending Eye Safety Sensor

Receiving Eye Safety Sensor

(Amber Indicator Light)

(Green Indicator Light)

6.My motor unit hums briefly:

ïFirst verify that the trolley is against the stop bolt.

ïRelease the door from the opener by pulling the Emergency Release Rope.

ïManually bring the door to a closed position.

ïLoosen the chain by adjusting the outer nut 4 to 5 turns. This relieves the tension.

ïRun the motor unit from the remote control or door control. The trolley should travel towards the door and stop. If the trolley re-engageswith the door, pull the Emergency Release Rope to disengage.

ïDecrease the UP travel by turning the UP Travel adjustment screw 2 full turns away from

the arrow.

ïRe-tightenthe outer nut so the chain is a

1/2" (13 mm) above the base of the rail. (When the door is reconnected and closed, the chain will sag. This is normal.)

ïIf the trolley does not move away from the bolt, repeat the steps above.

29

Bell Wire

 

Diagnostics

 

Located On

 

Motor Unit

 

LED or

 

Diagnostic

 

LED

 

"Learn"

Safety Sensor

Button

Diagnostic Chart

Installed

Safety Sensor

Your garage door opener is programmed with self-diagnosticcapabilities. The “Learn” button/diagnostic LED will flash a number of times then pause signifying it has found a potential issue. Consult Diagnostic Chart below.

1 FLASH

Safety sensors wire open (broken or disconnected).

OR

2 FLASHES

Safety sensors wire shorted or black/white wire reversed.

3 FLASHES

Door control or wire shorted.

4 FLASHES

Safety Sensors slightly misaligned (dim or flashing LED).

5 FLASHES

Motor overheated or possible RPM sensor failure. Unplug to reset.

6 FLASHES

Motor Circuit Failure.

Replace Receiver

Logic Board.

Symptom: One or both of the Indicator lights on the safety sensors do not glow steady.

ïInspect sensor wires for a short (staple in wire), correct wiring polarity (black/white wires reversed), broken or disconnected wires, replace/attach as needed.

ïDisconnect all wires from back of motor unit.

ïRemove sensors from brackets and shorten sensor wires to 1-2ft.(30-60cm) from back each of sensor.

ïReattach sending eye to motor unit using shortened wires. If sending eye indicator light glows steadily, attach the receiving eye.

ïAlign sensors, if the indicator lights glow replace the wires for the sensors. If the sensor indicator lights do not light, replace the safety sensors.

Symptom: LED is not lit on door control.

ïInspect door control/wires for a short (staple in wire), replace as needed.

ïDisconnect wires at door control, touch wires together. If motor unit activates, replace door control.

ïIf motor unit does not activate, disconnect door control wires from motor unit. Momentarily short across red and white terminals with jumper wire. If motor unit activates, replace door control wires.

Symptom: Sending indicator light glows steadily, receiving indicator light is dim or flashing.

ïRealign receiving eye sensor, clean lens and secure brackets.

ïVerify door track is firmly secured to wall and does not move.

Symptom: Motor has over heated; the motor unit does not operate or trolley is stuck on stop bolt = Motor unit hums briefly; RPM Sensor = Short travel6-8"(15-20cm).

ïUnplug unit to reset. Try to operate motor unit, check diagnostic code.

ïIf it is still flashing 5 times and motor unit moves 6-8"(15-20cm), replace RPM sensor.

ïIf motor unit doesnít operate, motor unit is overheated. Wait 30 minutes and retry. If motor unit still will not operate replace logic board.

Symptom: Motor unit doesn’t operate.

ï Replace logic board because motor rarely fails.

30

PROGRAMMING

NOTICE: If this Security® garage door opener is operated with anon-rollingcode transmitter, the technical measure in the receiver of the garage door opener, which provides security againstcode-theftdevices, will be circumvented. The owner of the copyright in the garage door opener does not authorize the purchaser or supplier of thenon-rollingcode transmitter to circumvent that technical measure.

Your garage door opener has already been programmed at the factory to operate with your hand-heldremote control. The door will open and close when you press the large push button.

Below are instructions for programming your opener to operate with additional Security ® remote controls.

To Add or Reprogram a Hand-heldRemote Control

USING THE “LEARN” BUTTON

 

 

USING THE MULTI-FUNCTIONDOOR CONTROL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1. Press and release the “learn” button on the motor unit. The learn indicator light will glow steadily for 30 seconds.

2. Within 30 seconds, press and hold the button on the hand-heldremote* that you wish to operate your garage door.

3.Release the button when the motor unit lights blink. It has learned the code. If light bulbs are not installed, two clicks will be heard.

To Erase All Codes From Motor

Unit Memory

To deactivate any unwanted remote, first erase all codes:

Press and hold the “learn” button on

motor unit until the learn indicator light goes out (approximately 6 seconds). All

previous codes are now erased. Reprogram each remote or keyless entry you wish to use.

LOCK

LIGHT

1. Press and hold the button on the hand-heldremote* that you wish to operate your garage door.

2.While holding the ENTER button, press and hold the LIGHT button on the Multi-FunctionDoor Control.

3.Continue holding the ENTER and LIGHT buttons while you press the push bar on the Multi-FunctionDoor Control (all three buttons are held).

LOCK

LIGHT

LOCK

4.Release buttons when the motor unit lights blink. It has learned the code. If light bulbs are not

installed, two clicks will be heard.

*3-ButtonRemotes

If provided with your garage door opener, the large button is factory programmed to operate it. Additional buttons on any

Security ® 3-Buttonremote or compact remote can be

programmed to operate other Security ® garage door openers.

31

To Add, Reprogram or Change a Keyless Entry PIN

NOTE: Your new Keyless Entry must be programmed to operate your garage door opener.

USING THE “LEARN” BUTTON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

USING THE MULTI-FUNCTIONDOOR CONTROL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1. Press and release the “learn” button on motor unit. The learn indicator light will glow steadily for

30 seconds.

2.Within 30 seconds, enter a four digit personal identification

number (PIN) of your choice on the keypad. Then press and hold the ENTER button.

3.Release the button when the motor unit lights blink. It has learned the code. If light bulbs are not installed, two clicks will be heard.

To change an existing, known PIN

If the existing PIN is known, it may be changed by one person without using a ladder.

1.Press the four buttons for the present PIN, then press and hold the # button.

The opener light will blink twice. Release the # button.

2.Press the new 4-digitPIN you have chosen, then press Enter.

The motor unit lights will blink once when the PIN has been learned.

Test by pressing the new PIN, then press Enter. The door should move.

To set a temporary PIN

LOCK

LIGHT

NOTE: This method requires two people if the Keyless Entry is already mounted outside the garage.

1.Enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold ENTER.

2.While holding the ENTER button, press and hold the LIGHT button on the Multi-FunctionDoor Control.

3.Continue holding the ENTER and LIGHT buttons while you press the push bar on the Multi-FunctionDoor Control (all three buttons are held).

4.Release buttons when the motor unit lights blink. It has learned the code. If light bulbs are not installed, two clicks will be heard.

LOCK

LIGHT

LOCK

2.Press the temporary 4-digitPIN you have chosen, then press Enter.

The opener light will blink four times.

3.To set the number of hours this temporary PIN will work, press the number of hours (up to 255), then press .

OR

You may authorize access by visitors or service people with a temporary 4-digitPIN. After a programmed number of hours or number of accesses, this temporary PIN expires and will no longer open the door. It can be used toclose the door even after it has expired. To set a temporary PIN:

1.Press the four buttons for your personal entry PIN (not the last temporary PIN), then press and hold thebutton.

The opener light will blink three times. Release the button.

3.To set the number of times this temporary PIN will work, press the number of times (up to 255), then press #.

The opener light will blink once when the temporary PIN has been learned.

Test by pressing the four buttons for the temporary PIN, then press Enter. The door should move. If the temporary PIN was set to a certain number of openings, remember that the test has used up one opening.To clear the temporary password, repeat steps 1-3,setting the number of hours or times to 0 in step 3.

32

REPAIR PARTS

 

 

 

 

Rail Assembly Parts

 

 

 

 

1

 

5

 

 

 

 

 

 

3

4

 

 

 

 

 

 

 

2

 

KEY

PART

 

 

 

 

 

 

NO.

NO.

DESCRIPTION

 

 

1

4A1008

Master link kit

 

6

2

41A4813

Chain pulley bracket

 

3

41A3489

Complete trolley assembly

 

 

 

 

4

1707LM

One-piecerail

 

 

5

41D3484

Full chain assembly

 

 

6

83A11-2

Rail grease

Installation Parts

 

 

 

 

1

 

2

4

 

 

 

 

 

3

 

 

 

LOCK

LIGHT

 

 

 

 

 

 

 

 

 

 

LY

 

 

 

NT

ON

 

 

 

OU

 

 

 

 

G M

 

 

 

 

LIN

 

 

 

7

CEI

 

 

 

UP

 

 

 

 

 

 

 

5

 

 

 

NOTICE

6

 

 

 

 

 

 

 

10

8

11

9

12

 

 

 

 

KEY

PART

 

NO.

NO.

DESCRIPTION

 

 

 

 

1

 

41A5273-1

Multi-functiondoor control panel

2

 

971LM

1 Button remote control

3

 

10A20

3V2032 Lithium battery

4

 

29B137

Remote control visor clip

5

 

41A2828

Emergency release rope & handle

 

 

 

assembly

6

 

41B4494-1

2-Conductorbell wire, white & white/red

7

 

41A4353

Header bracket w clevis pin & fastener

8

 

41A5047

Door bracket w/clevis pin & fastener

9

 

178B35

Curved door arm section

10

 

178B34

Straight door arm section

11

 

41A5034

Safety sensor kit (receiving and

 

 

 

sending eyes) with 3' (.9 m)

 

 

 

2-conductorbell wire

12

 

41A5266-1

Safety sensor brackets (2)

 

 

 

NOT SHOWN

 

 

41A2770-6

Installation hardware bag

 

 

 

(includes hardware listed on page 5).

 

 

114A2683

Owner’s manual

 

 

114A2683SP

Spanish manual

 

 

 

 

33

Motor Unit Assembly Parts

 

 

1

4

18

 

 

 

 

 

2

 

 

 

 

 

6

 

3

 

17

 

 

 

 

 

10

16

 

 

19

 

 

 

 

 

 

7

8

11

5

15

 

 

 

14

13

9

(Down)

 

 

 

 

Brown Contact

 

 

Wire

12

 

DN

 

 

 

 

Drive

 

 

Gear

LIMIT SWITCH ASSY.

Grey

Wire

UP

 

 

 

 

 

Center Limit (Up)

Yellow

 

 

 

 

 

 

Contact

Contact

 

 

 

 

 

 

Wire

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

KEY

PART

 

KEY

PART

 

 

 

 

NO.

NO.

DESCRIPTION

NO.

NO.

DESCRIPTION

 

 

 

1

31D380

Sprocket cover

12

41A5525-1

Cover

 

 

 

2

41C4220A

Gear and sprocket assembly

13

41A2818

Limit switch drive & retainer

 

 

 

 

Complete with: Spring washer,

14

41D3452

Limit switch assembly

 

 

 

 

thrust washer, retaining ring,

 

 

 

 

15

41A2822-1

Interrupter cup assembly

 

 

 

 

bearing plate, roll pins (2), drive

 

 

 

 

16

41C4398A

RPM sensor assembly

 

 

 

 

gear and worm gear, helical gear

 

 

 

 

w/retainer and grease

17

41A5483-1B

Receiver logic board assy.

 

 

 

 

 

 

 

3

41A2817

Drive/worm gear kit w/grease,

 

 

Complete with: Logic board, end

 

 

 

 

roll pins (2)

 

 

panel w/all labels, light socket

 

 

4

41B4245

Line cord

18

41C5498

Low voltage wire harness assy.

 

 

5

41A5484-1

End panel w/all labels

 

41C5497

High voltage wire harness assy.

 

 

19

41D180-1

End panel w/all labels

 

 

6

4A1344

Light socket

 

 

 

 

 

 

 

 

7

108D68

Lens

 

41A2826

NOT SHOWN

 

 

 

8

30B532

Capacitor - 1/2 HP

 

Motor shaft bearing kit

 

 

 

41A2825

Opener assembly hardware kit

 

 

 

30B533

Capacitor - 1/3 HP

 

 

 

 

 

 

(includes screws not designated

 

 

9

12A373

Capacitor bracket

 

 

 

 

 

 

by a number in illustration)

 

 

10

41A3150

Terminal block w/screws

 

 

 

 

 

 

 

 

 

 

11

41D3058

Universal replacement motor &

 

 

 

 

 

 

 

 

bracket assembly

 

 

 

 

 

 

 

 

Complete with: Motor, worm,

 

 

 

 

 

 

 

 

bracket, bearing assembly, RPM

 

 

 

 

 

 

 

 

sensor

 

 

 

 

 

 

 

 

 

 

 

 

 

 

34

ACCESSORIES

1702LM Outside Quick Release: 995LM

Required for a garage with NO access door. Enables homeowner to open garage door manually from outside by disengaging trolley.

1708LM

1710LM

41A5281

78LM

LOCK

LIGHT

8 Foot (2.4 m) Complete Rail:

971LM

To allow an 8 foot (2.4 m) door to open fully.

972LM

10 Foot (3 m) Complete Rail:

To allow a 10 foot (3 m) door to open fully.

973LM

Extension Brackets:

(Optional) For safety sensor installation onto the wall or floor.

Multi-FunctionDoor

974LM

 

Control Panel:

 

Provides a Lock Feature which prevents

 

operation of garage door opener from

 

portable remotes and a Light Feature for

 

constant light.

970LM

 

902LM/903LM

915LM

CLOSED

OPEN

2 & 3 Door Multi-FunctionWall

Control:

Ideal for homes with up to three garage doors. Combine up to three controls into one wall control panel for a neat compact appearance. Enhanced functions include Lock Feature to lock out outside radio signals while you are away from home and turn opener lights on or off from the control panel.

Garage Door Monitor:

Security for the largest door of your home!

Tells you if your garage door is open or closed. Monitors up to 4 garage doors by adding additional sensor modules.

976LM

98LM

916LM

Garage Door Monitor Sensor:

LOCK

LIGHT

Additional accessory sensor for homes with multiple garage doors.

Remote Light Control:

Enables homeowner to turn on a lamp, television or other appliance from their car with their garage door opener remote or from anywhere in their home with an additional LiftMaster Security ® remote.

1-ButtonSecurity® Remote Control:

Includes visor clip.

2-ButtonSecurity® Remote Control:

Includes visor clip.

3-ButtonSecurity® Remote Control:

Includes visor clip.

4-ButtonSecurity® Remote Control:

Includes visor clip.

3-ButtonMini-RemoteControl with Security®:

With key ring and fastening strip.

Wireless Keyless Entry with Security ®:

Enables homeowner to operate garage door opener from outside by entering a password on a specially designed keyboard. Also can add a temporary password for visitors or service persons. This temporary password can be limited to a programmable number of hours or entries.

Motion Detecting Control Panel:

Multi-Functiondoor control with motion sensor that automatically turns opener lights on for 5 minutes when it detects a person entering the garage. Sensor can be easily deactivated when desired.

35

LIFTMASTER SERVICE IS

ON CALL

OUR LARGE SERVICE ORGANIZATION

SPANS AMERICA

INSTALLATION AND SERVICE INFORMATION IS AS NEAR AS YOUR TELEPHONE SEVEN DAYS A WEEK.

SIMPLY DIAL OUR TOLL FREE NUMBER:

1-800-528-2817

HOURS: (Central Standard Time)

6:00 A.M. TO 7:00 P.M. - Monday through Friday 8:00 A.M. TO 6:00 P.M. - Saturday

8:00 A.M. To 4:30 P.M. - Sunday

www.liftmaster.com

For professional installation, parts and service, contact your local LIFTMASTER/CHAMBERLAIN dealer. Look for him in the Yellow Pages, or call our Service number for a list of dealers in your area.

HOW TO ORDER

REPAIR PARTS

Selling prices will be furnished on request or parts will be shipped at prevailing prices and you will be billed accordingly.

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:

PART NUMBER

PART NAME

MODEL NUMBER

ADDRESS ORDERS TO:

THE CHAMBERLAIN GROUP, INC.

Technical Support Group

6020 S. Country Club Road

Tucson, Arizona 85706

SERVICE INFORMATION TOLL FREE NUMBER:

1-800-528-2817

LIFTMASTER ONE-YEARLIMITED WARRANTY

FOUR YEAR MOTOR LIMITED WARRANTY

The Chamberlain Group, Inc. (“Seller”) warrants to the first retail purchaser of this product, for the residence in which this product is originally installed, that it is free from defect in materials and/or workmanship for a period of one year from the date of purchase and that the motor is free from defect in materials and/or workmanship for a period of four years from the date of purchase. The proper operation of this product is dependent on your compliance with the instructions regarding installation, operation, maintenance and testing. Failure to comply strictly with those instructions will void this warranty in its entirety.

If, during the limited warranty period, this product appears to contain a defect covered by this limited warranty, call 1-800-528-2817,toll free, before dismantling this product. Then send this product,pre-paidand insured, to our service center for warranty repair. You will be advised of shipping instructions when you call. Please include a brief description of the problem and a datedproof-of-purchasereceipt with any product returned for warranty repair. Products returned to Seller for warranty repair, which upon receipt by Seller are confirmed to be defective and covered by this limited warranty, will be repaired or replaced (at Seller’s sole option) at no cost to you and returnedpre-paid.Defective parts will be repaired or replaced with new orfactory-rebuiltparts at Seller’s sole option.

THIS LIMITED WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, AND OF ANY OTHER OBLIGATIONS OR LIABILITY ON SELLER’S PART. THIS LIMITED WARRANTY DOES NOT COVER NONDEFECT DAMAGE, DAMAGE CAUSED BY IMPROPER INSTALLATION, OPERATION OR CARE (INCLUDING, BUT NOT LIMITED TO ABUSE, MISUSE, FAILURE TO PROVIDE REASONABLE AND NECESSARY MAINTENANCE, UNAUTHORIZED REPAIRS OR ANY ALTERATIONS TO THIS PRODUCT), LABOR CHARGES FOR REINSTALLING A REPAIRED OR REPLACED UNIT, REPLACEMENT OF BATTERIES AND LIGHT BULBS OR UNITS INSTALLED FOR NONRESIDENTIAL USE.

THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH, OR RELATING TO, THE GARAGE DOOR OR GARAGE DOOR HARDWARE, INCLUDING BUT NOT LIMITED TO THE DOOR SPRINGS, DOOR ROLLERS, DOOR ALIGNMENT OR HINGES. ANY SERVICE CALL THAT DETERMINES THE PROBLEM HAS BEEN CAUSED BY ANY OF THESE ITEMS COULD RESULT IN A FEE TO YOU.

UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES ARISING IN CONNECTION WITH USE, OR INABILITY TO USE, THIS PRODUCT. IN NO EVENT SHALL SELLER’S LIABILITY FOR BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE OR STRICT LIABILITY EXCEED THE COST OF THE PRODUCT COVERED HEREBY. NO PERSON IS AUTHORIZED TO ASSUME FOR US ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT.

Some states do not allow the exclusion or limitation of consequential, incidental or special damages, so the above limitation or exclusion may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

 

© 2004, The Chamberlain Group, Inc.

 

114A2683E

All Rights Reserved

Printed in Mexico