FRANÇAIS ESPAÑOL ENGLISH
INSTALLATION MANUAL
ELECTRIC CONVECTION BUILT-IN OVEN
Please read these instructions thoroughly before installing and operating the oven.
LWS3081ST LWS3010ST
LWD3081ST LWD3010ST
www.lg.com
MFL51224801
Part 1 |
SAFETY |
1 
BEFORE YOU BEGIN
Remove all tape and packing materials before using the oven. Dispose all plastic bags after unpacking the oven. Never allow children to play with packing materials.
You can download an Installation manual at http://www.lg.com.
• Home > Region Selection > Support > Appliances Wall Ovens > Model selection > Download the manual
IMPORTANT SAFETY INSTRUCTIONS
Read and follow all instructions before using your oven to prevent the risk of fire, electric shock, injury to person, or damage when using the oven. This guide does not cover all possible conditions that may occur. For further assistance contact your service agent or manufacturer.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “WARNING” or “CAUTION”. These words mean :
WARNING
CAUTION
This symbol will alert you to hazards or unsafe practices which could cause serious bodily harm or death.
This symbol will alert you to hazards or unsafe practices which could cause bodily injury or property damage.
WARNING
• The information in this manual should be followed exactly.
- A fire or electrical shock may result causing property damage, personal injury or death.
• DO NOT put any weight on the oven door. Never allow anyone to climb, sit, stand or hang on the oven door.
- The oven could be tipped and injury might result from food or the oven itself.
•The electrical power must be shut off while the electrical connections are being made.
- Failure to do so can result in severe personal injury, death or electrical shock.
•New branch-circuit installations (1996 NEC), mobile homes, recreational vehicles, or installations where local codes prohibit grounding through the neutral conductor require 4-wire branch-circuit connection.
•Improper connection of aluminum house wiring to copper leads can result in an electrical hazard or fire. Use only connectors designed for joining copper to aluminum and follow the manufacturer’s recommended procedure closely.
•Mounting screws must be used.
- Failure to do so can result in the oven falling out of the cabinet causing serious injury.
CAUTION
•Make sure the cabinets and wall coverings around the oven can withstand the temperature (up to 194˚F[90˚C]) generated by the oven.
- Discoloration, delamination or melting may occur.
• DO NOT remove spacers on the side walls of the built-in oven.
- These spacers center the oven in the space provided.The oven must be centered to prevent excess heat buildup that may result in heat damage or fire.
• DO NOT block the oven air exhaust located at the bottom of the oven.
- Blocking the exhaust may cause cabinet damage and product malfunction.
- 2 -
Part 1 |
SAFETY |
IMPORTANT NOTE
This installation must be completed by a qualified installer or technician.
•Please read the entire Installation Instructions prior to installation.
•Remove all packing materials from the oven compartments before connecting the electrical supply to the oven.
•Installer: please retain these instructions for local inspector’s reference, then leave them with the consumer.
•Consumer: please read and keep these instructions for future reference and be sure to read the entire OWNER’S MANUAL prior to use.
PREPARE TO INSTALL THE OVEN
WARNING
• The information in this manual should be followed exactly.
-A fire or electrical shock may result causing property damage, personal injury or death.
WARNING
•DO NOT put any weight on the oven door. Never allow anyone to climb,
sit, stand or hang on the oven door.
-The oven could tip and injury might result from food or the oven itself.
Phillips Screwdriver |
Drill |
PREPARE TO INSTALL THE OVEN
6 Screws For |
6 Wood Screws |
Bottom Trim |
For Mounting |
(3 needed for installation |
(4 needed for |
and 3 extra’s) |
installation and 2 |
|
extra’s) |
WARNING
•The electrical power must be shut off while the electrical connections are
being made.
-Failure to do so can result in severe personal injury, death or electrical shock.
30” (76.2 cm) Metal Bottom Trim
MATERIALS NEEDED
ENGLISH
Junction Box |
Wire Nuts |
3/4” Conduit |
|
|
Connector |
|
36” (91 cm) |
|
|
of String |
|
- 3 -
Part 2 INSTALLATION REQUIREMENTS
1 
INSTALLATION DRAWINGS (FOR 30” SINGLE BUILTIN OVEN)
The first step of your installation should be to measure your current cutout dimensions and compare them to the cutout dimensions shown below. You may find little or no cabinet work will be necessary.
IMPORTANT NOTE
•The cabinet base platform must be able to support 190lbs (86Kg). If the cabinet does not have a solid bottom, two braces or runners must be installed level with the bottom of the cutout to support the weight of the oven. Make sure the base is level and front of cabinet is square. If the cabinet base is not level, the oven glides will tend to slide out when opening the door.
•If marks, blemishes or the cutout opening are visible above the installed oven, it may be necessary to add wood shims under the runners and front trim until the marks or opening are covered.
•If the cabinet does not have a front frame and the sides are less than 3/4” (1.9 cm) thick, shim both sides equally to establish the cutout width.
•The junction box must be flush with the rear wall of the cabinet as shown below.
•Allow at least 23” clearance for door depth when it is open.
Product dimensions
27 3/8”
(69.5 cm)
29 5/16” |
28 7/8” |
(74.5 cm) |
(73.3 cm) |
|
|
|
|
|
|
|
29 3/4” |
|
|
|
|
|
|
|
|
|
|
|
23 3/8” |
|
(75.5 cm) |
|
|
|
|
|
(59.3 cm) |
|
|
|
|
|
|
|
Cutout dimensions
Cabinet Width |
30” (762 mm) |
|
Recommended |
|
|
Minimum |
|
|
Cutout location |
|
|
from floor |
31” (787.4 m) |
|
Cutout Depth |
23 |
1/2” Min. (596.9 mm) |
Cutout Width |
28 |
1/2” Min. (723.9 mm) |
|
28 |
5/8” Max. (727 mm) |
Cutout Height |
28 |
15/16” Min. (735 mm) |
|
29” Max. (736.6 mm) |
|
Allow 1” minimum for overlap of oven
23”
30”
5”
28 1/2” Min.
28 5/8” Max. 
Junction Box
Location
23 1/2”
|
28 15/16” Min. |
|
|
29” Max. |
|
Allow 1” |
23 1/2” |
|
Minimum cutout |
||
minimum for |
||
location from |
||
overlap of oven |
||
floor 31” |
||
|
||
|
|
- 4 -
Loading...