Lenovo 9266, 9384, 6491, 8972, 9649 User Manual

...
0 (0)

User Guide

Types 6491, 8013, 8702, 8706

Types 8716, 8970, 8972, 8976

Types 8980, 8982, 8986, 8992

Types 8994, 9266, 9276, 9278

Types 9282, 9286, 9288, 9374

Types 9378, 9380, 9384, 9628

Types 9632, 9647, 9649, 9695

User Guide

Note

Before using this information and the product it supports, be sure to read the “Important safety information” on page v and Appendix B, “Notices,” on page 73.

Fourth Edition (February 2007)

© Copyright Lenovo 2006, 2007.

Portions © Copyright International Business Machines Corporation 2005. All rights reserved.

U.S. GOVERNMENT USERS – RESTRICTED RIGHTS: Our products and/or services are provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to the GSA ADP Schedule contract with Lenovo Group Limited, if any, or the standard terms of this commercial license, or if the agency is unable to accept this Program under these terms, then we provide this Program under the provisions set forth in Commercial Computer Software–Restricted Rights at FAR 52.227-19, when applicable, or under Rights in Data-General, FAR 52.227.14 (Alternate III).

Contents

Important safety information . . . . .

.

 

v

Locating controls and connectors on the front of

 

 

Conditions that require immediate action . . .

.

. v

your computer . . . . . . . . . . .

.

19

General safety guidelines . . . . . . . . .

. vi

Locating connectors on the rear of your computer

20

Service and upgrades . . . . . . . . .

. vi

Obtaining device drivers . . . . . . . .

.

21

Static electricity prevention . . . . . . .

. vii

Removing the cover . . . . . . . . . .

.

22

Power cords and power adapters . . . . .

. vii

Locating components . . . . . . . . . .

.

23

Voltage-selection switch . . . . . . . .

. viii

Accessing system board components . . . . .

.

24

Extension cords and related devices . . . .

. ix

Identifying parts on the system board . . . .

.

25

Plugs and outlets . . . . . . . . . .

. ix

Installing memory . . . . . . . . . . .

.

29

External devices . . . . . . . . . . .

. ix

Installing PCI adapters . . . . . . . . .

.

30

Batteries . . . . . . . . . . . . .

. ix

Installing internal drives . . . . . . . . .

.

31

Heat and product ventilation . . . . . .

.

. x

Drive specifications. . . . . . . . . .

.

32

Operating environment . . . . . . . .

. xi

Installing a drive in bay 1 . . . . . . .

.

33

Electrical current safety information . . . . .

. xi

Installing a diskette drive in bay 3. . . . .

.

34

Lithium battery notice. . . . . . . . . .

. xii

Installing security features . . . . . . . .

.

35

Modem safety information . . . . . . . .

. xii

Integrated cable lock . . . . . . . . .

.

36

Laser compliance statement. . . . . . . .

. xiii

Padlock. . . . . . . . . . . . . .

.

37

Power supply statement . . . . . . . . .

. xiii

Password protection . . . . . . . . .

.

37

Products with television tuner options installed .

. xiii

Changing the battery . . . . . . . . . .

.

37

Note to CATV system installer. . . . . .

. xiv

Erasing a lost or forgotten password (clearing

 

 

Example of antenna grounding . . . . .

. xiv

CMOS) . . . . . . . . . . . . . . .

.

38

Data safety . . . . . . . . . . . . .

. xv

Replacing the cover and connecting the cables. .

.

39

Cleaning and maintenance . . . . . . . .

. xv

Chapter 4. Recovering software . . . .

 

41

Using headphones or earphones . . . . . .

. xv

 

Additional safety information . . . . . . .

. xvi

Creating and using the Product Recovery disc . .

. 41

Introduction . . . . . . . . . . . . xvii

Performing backup and recovery operations . .

. 42

Using the Rescue and Recovery workspace . . .

. 43

 

 

 

 

Creating and using rescue media . . . . . .

. 44

Chapter 1. Arranging your workspace .

. 1

Creating and using a Recovery Repair diskette .

. 45

Comfort . . . . . . . . . . . . . . .

.

1

Recovering or installing device drivers . . . .

.

46

Setting a rescue device in the startup sequence .

. 47

Glare and lighting . . . . . . . . . .

.

.

1

Solving recovery problems . . . . . . . .

.

47

Air circulation . . . . . . . . . . . .

.

.

2

 

 

 

Electrical outlets and cable lengths . . . . .

.

.

2

Chapter 5. Using the Setup Utility . . .

 

49

 

 

 

 

 

Chapter 2. Setting up your computer .

. 3

Starting the Setup Utility program. . . . . .

.

49

Installing the vertical stand . . . . . . .

.

.

3

Viewing and changing settings . . . . . . .

.

49

Using passwords . . . . . . . . . . .

.

49

Connecting your computer . . . . . . .

.

.

4

Password considerations . . . . . . . .

.

49

Turning on power . . . . . . . . . . .

.

 

10

 

User Password . . . . . . . . . . .

.

50

Finishing the software installation . . . . . .

.

 

10

 

Administrator Password . . . . . . . .

.

50

Completing important tasks . . . . . . . .

.

 

10

 

Setting, changing, and deleting a password . . . 50

Updating your operating system . . . . . .

. 11

Using Security Profile by Device . . . . . .

.

50

Installing other operating systems . . . . . .

.

 

11

 

Selecting a startup device. . . . . . . . .

.

51

Updating your antivirus software . . . . . .

.

 

11

 

Selecting a temporary startup device . . . .

.

51

Shutting down the computer . . . . . . .

. 11

Changing the startup device sequence . . .

. 51

 

 

 

 

Chapter 3. Installing options . . . .

.

13

Advanced settings . . . . . . . . . . .

.

52

Exiting from the Setup Utility program . . . .

. 52

Features . . . . . . . . . . . . . .

.

 

13

 

 

 

 

Available options . . . . . . . . . . .

.

 

16

Chapter 6. Updating system programs

 

53

Specifications . . . . . . . . . . . . . .

 

17

 

 

Using system programs . . . . . . . . .

.

53

Supported operating positions . . . . . . .

.

 

18

 

Updating (flashing) BIOS from a diskette . . .

. 53

Tools required . . . . . . . . . . . .

.

 

18

 

 

 

 

Handling static-sensitive devices . . . . . .

.

 

18

Chapter 7. Troubleshooting and

 

 

Installing external options . . . . . . . .

.

 

19

 

 

 

diagnostics . . . . . . . . . . . . .

 

55

 

 

 

 

 

© Lenovo 2006, 2007. Portions © IBM Corp. 2005.

iii

Basic troubleshooting . . . . . . . . . .

.

55

Calling for service . . . . . . . . .

.

.

63

Diagnostic programs . . . . . . . . . .

.

56

Using other services . . . . . . . .

.

.

64

PC-Doctor for Windows . . . . . . . .

.

57

Purchasing additional services . . . . .

.

.

64

PC-Doctor for DOS . . . . . . . . . .

.

57

 

 

 

 

PC-Doctor for Windows PE . . . . . . .

. 59

Appendix A. Manual modem

 

 

 

Cleaning the mouse . . . . . . . . . .

.

59

commands . . . . . . . . . . .

.

.

65

Optical mouse . . . . . . . . . . .

.

59

Basic AT commands . . . . . . . . .

.

.

65

Non-optical mouse . . . . . . . . . .

.

59

Extended AT commands . . . . . . . .

.

. 67

 

 

 

Chapter 8. Getting information, help,

 

 

MNP/V.42/V.42bis/V.44 commands . . . .

.

. 68

 

 

Fax Class 1 commands . . . . . . . .

.

.

69

and service . . . . . . . . . . . .

.

61

Fax Class 2 commands . . . . . . . .

.

.

69

Information resources . . . . . . . . . .

.

61

Voice commands. . . . . . . . . . .

.

.

70

Online Books folder . . . . . . . . .

.

61

 

 

 

 

ThinkVantage Productivity Center . . . . .

. 61

Appendix B. Notices . . . . . . .

.

.

73

Access Help . . . . . . . . . . . .

.

62

Television output notice . . . . . . . .

.

.

74

Safety and warranty . . . . . . . . .

.

62

Trademarks . . . . . . . . . . . . . . 74

www.lenovo.com . . . . . . . . . . . 62

 

 

 

 

Help and service . . . . . . . . . . .

.

62

Index . . . . . . . . . . . . .

.

.

75

Using the documentation and diagnostic

 

 

 

 

 

 

 

 

programs . . . . . . . . . . . . .

.

63

 

 

 

 

iv User Guide

Important safety information

Note

Please read important safety information first.

This information can help you safely use your desktop or notebook personal computer. Follow and retain all information included with your computer. The information in this document does not alter the terms of your purchase agreement or the LenovoLimited Warranty. For more information, refer to the safety and warranty information that is provided with your computer.

Customer safety is important. Our products are developed to be safe and effective. However, personal computers are electronic devices. Power cords, power adapters, and other features can create potential safety risks that can result in physical injury or property damage, especially if misused. To reduce these risks, follow the instructions included with your product, observe all warnings on the product and in the operating instructions, and review the information included in this document carefully. By carefully following the information contained in this document and provided with your product, you can help protect yourself from hazards and create a safer computer work environment.

Note: This information includes references to power adapters and batteries. In addition to notebook computers, some products (such as speakers and monitors) ship with external power adapters. If you have such a product, this information applies to your product. In addition, computer products contain a coin-sized internal battery that provides power to the system clock even when the computer is unplugged, so the battery safety information applies to all computer products.

Conditions that require immediate action

Products can become damaged due to misuse or neglect. Some product damage is serious enough that the product should not be used again until it has been inspected and, if necessary, repaired by an authorized servicer.

As with any electronic device, pay close attention to the product when it is turned on. On very rare occasions, you might notice an odor or see a puff of smoke or sparks vent from your product. Or you might hear sounds like popping, cracking, or hissing. These conditions might merely mean that an internal electronic component has failed in a safe and controlled manner. Or, they might indicate a potential safety issue. However, do not take risks or attempt to diagnose the situation yourself. Contact the Customer Support Center for further guidance. For a list of Service and Support phone numbers, see refer to the safety and warranty information that is provided with your computer.

Frequently inspect your computer and its components for damage, wear, or signs of danger. If you have any question about the condition of a component, do not use the product. Contact the Customer Support Center or the product manufacturer for instructions on how to inspect the product and have it repaired, if necessary.

© Lenovo 2006, 2007. Portions © IBM Corp. 2005.

v

In the unlikely event that you notice any of the following conditions, or if you have any safety concerns with your product, stop using the product and unplug it from the power source and telecommunication lines until you can speak to the Customer Support Center for further guidance. See Chapter 8, “Getting information, help, and service,” on page 61.

vPower cords, plugs, power adapters, extension cords, surge protectors, or power supplies that are cracked, broken, or damaged.

vSigns of overheating, smoke, sparks, or fire.

vDamage to a battery (such as cracks, dents, or creases), discharge from a battery, or a buildup of foreign substances on the battery.

vA cracking, hissing, or popping sound, or strong odor that comes from the product.

vSigns that liquid has been spilled or an object has fallen onto the computer product, the power cord, or power adapter.

vThe computer product, power cord, or power adapter has been exposed to water.

vThe product has been dropped or damaged in any way.

vThe product does not operate normally when you follow the operating instructions.

Note: If you notice these conditions with a product (such as an extension cord) that is not manufactured for or by Lenovo, stop using that product until you can contact the product manufacturer for further instructions, or until you get a suitable replacement.

General safety guidelines

Always observe the following precautions to reduce the risk of injury and property damage.

Service and upgrades

Do not attempt to service a product yourself unless instructed to do so by the Customer Support Center or your documentation. Only use a service provider who is approved to repair your particular product.

Note: Some computer parts can be upgraded or replaced by the customer. Upgrades typically are referred to as options. Replacement parts approved for customer installation are referred to as Customer Replaceable Units, or CRUs. Lenovo provides documentation with instructions when it is appropriate for customers to install options or replace CRUs. You must closely follow all instructions when installing or replacing parts. The Off state of a power indicator does not necessarily mean that voltage levels inside a product are zero. Before you remove the covers from a product equipped with an ac power cord, always make sure that the power is turned off and that the product is unplugged from any power source. For more information on CRUs, refer to the User Guide for this product. If you have any questions or concerns, contact the Customer Support Center.

Although there are no moving parts in your computer after the power cord has been disconnected, the following warnings are required for your safety.

vi User Guide

Danger

Hazardous moving parts. Keep fingers and other body parts away.

Attention

Before replacing any CRUs, turn off the computer and wait three to five minutes to let the computer cool before opening the cover.

Static electricity prevention

Static electricity, although harmless to you, can seriously damage computer components and options. Improper handling of static-sensitive parts can cause damage to the part. When you unpack an option or CRU, do not open the static-protective package containing the part until the instructions direct you to install it.

When you handle options or CRUs, or perform any work inside the computer, take the following precautions to avoid static-electricity damage:

vLimit your movement. Movement can cause static electricity to build up around you.

vAlways handle components carefully. Handle adapters, memory modules, and other circuit boards by the edges. Never touch exposed circuitry.

vPrevent others from touching components.

vWhen you install a static-sensitive option or CRU, touch the static-protective package containing the part to a metal expansion-slot cover or other unpainted metal surface on the computer for at least two seconds. This reduces static electricity in the package and your body.

vWhen possible, remove the static-sensitive part from the static-protective packaging and install the part without setting it down. When this is not possible, place the static-protective packaging on a smooth, level surface and place the part on it.

vDo not place the part on the computer cover or other metal surface.

Power cords and power adapters

Use only the power cords and power adapters supplied by the product manufacturer.

Important safety information vii

The power cords shall be safety approved. For Germany, it shall be H05VV-F, 3G, 0.75 mm2, or better. For other countries, the suitable types shall be used accordingly.

Never wrap a power cord around a power adapter or other object. Doing so can stress the cord in ways that can cause the cord to fray, crack, or crimp. This can present a safety hazard.

Always route power cords so that they will not be walked on, tripped over, or pinched by objects.

Protect power cord and power adapters from liquids. For instance, do not leave your power cord or power adapter near sinks, tubs, toilets, or on floors that are cleaned with liquid cleansers. Liquids can cause a short circuit, particularly if the power cord or power adapter has been stressed by misuse. Liquids also can cause gradual corrosion of power cord terminals and/or the connector terminals on a power adapter, which can eventually result in overheating.

Always connect power cords and signal cables in the correct order and ensure that all power cord connectors are securely and completely plugged into receptacles.

Do not use any power adapter that shows corrosion at the ac input pins or shows signs of overheating (such as deformed plastic) at the ac input or anywhere on the power adapter.

Do not use any power cords where the electrical contacts on either end show signs of corrosion or overheating or where the power cord appears to have been damaged in any way.

Voltage-selection switch

Some computers are equipped with a voltage-selection switch located near the power-cord connection point on the computer. If your computer has a voltage-selection switch, ensure that you set the switch to match the voltage available at your electrical outlet. Setting the voltage-selection switch incorrectly can cause permanent damage to the computer.

If your computer does not have a voltage-selection switch, your computer is designed to operate only at the voltage provided in the country or region where the computer was originally purchased.

If you relocate your computer to another country, be aware of the following:

vIf your computer does not have a voltage-selection switch, do not connect the computer to an electrical outlet until you have verified that the voltage provided is the same as it was in the country or region where the computer was originally purchased.

vIf your computer has a voltage selection switch, do not connect the computer to an electrical outlet until you have verified that the voltage-selection switch is set to match the voltage provided in that country or region.

If you are not sure of the voltage provided at your electrical outlet, contact your local electric company or refer to official Web sites or other literature for travelers to the country or region where you are located.

viii User Guide

Extension cords and related devices

Ensure that extension cords, surge protectors, uninterruptible power supplies, and power strips that you use are rated to handle the electrical requirements of the product. Never overload these devices. If power strips are used, the load should not exceed the power strip input rating. Consult an electrician for more information if you have questions about power loads, power requirements, and input ratings.

Plugs and outlets

If a receptacle (power outlet) that you intend to use with your computer equipment appears to be damaged or corroded, do not use the outlet until it is replaced by a qualified electrician.

Do not bend or modify the plug. If the plug is damaged, contact the manufacturer to obtain a replacement.

Do not share an electrical outlet with other home or commercial appliances that draw large amounts of electricity; otherwise, unstable voltage might damage your computer, data, or attached devices.

Some products are equipped with a three-pronged plug. This plug fits only into a grounded electrical outlet. This is a safety feature. Do not defeat this safety feature by trying to insert it into a non-grounded outlet. If you cannot insert the plug into the outlet, contact an electrician for an approved outlet adapter or to replace the outlet with one that enables this safety feature. Never overload an electrical outlet. The overall system load should not exceed 80 percent of the branch circuit rating. Consult an electrician for more information if you have questions about power loads and branch circuit ratings.

Be sure that the power outlet you are using is properly wired, easily accessible, and located close to the equipment. Do not fully extend power cords in a way that will stress the cords.

Be sure that the power outlet provides the correct voltage and current for the product you are installing.

Carefully connect and disconnect the equipment from the electrical outlet.

External devices

Do not connect or disconnect any external device cables other than USB and 1394 cables while the computer power is on; otherwise, you might damage your computer. To avoid possible damage to attached devices, wait at least five seconds after the computer is shut down to disconnect external devices.

Batteries

All personal computers manufactured by Lenovo contain a non-rechargeable coin cell battery to provide power to the system clock. In addition, many mobile products, such as notebook computers, utilize a rechargeable battery pack to provide system power when in portable mode. Batteries supplied by Lenovo for use with your product have been tested for compatibility and should only be replaced with approved parts.

Important safety information

ix

Never attempt to open or service any battery. Do not crush, puncture, or incinerate batteries or short circuit the metal contacts. Do not expose the battery to water or other liquids. Only recharge the battery pack strictly according to instructions included in the product documentation.

Battery abuse or mishandling can cause the battery to overheat, which can cause gasses or flame to “vent” from the battery pack or coin cell. If your battery is damaged, or if you notice any discharge from your battery or the buildup of foreign materials on the battery leads, stop using the battery and obtain a replacement from the battery manufacturer.

Batteries can degrade when they are left unused for long periods of time. For some rechargeable batteries (particularly Lithium Ion batteries), leaving a battery unused in a discharged state could increase the risk of a battery short circuit, which could shorten the life of the battery and can also pose a safety hazard. Do not let rechargeable Lithium-Ion batteries completely discharge or store these batteries in a discharged state.

Heat and product ventilation

Computers, AC adapters, and many accessories can generate heat when turned on and when batteries are charging. Always follow these basic precautions:

vDo not leave your computer, AC adapter, or accessories in contact with your lap or any part of your body for an extended period when the products are functioning or when the battery is charging. Your computer, AC adapter, and many accessories produce some heat during normal operation. Extended contact with the body could cause discomfort or, potentially, a skin burn.

vDo not charge the battery or operate your computer, AC adapter, or accessories near flammable materials or in explosive environments.

vVentilation slots, fans, and heat sinks are provided with the product for safety, comfort, and reliable operation. These features might inadvertently become blocked by placing the product on a bed, sofa, carpet, or other flexible surface. Never block, cover, or disable these features.

Inspect your desktop computer for dust accumulation at least once every three months. Before inspecting your computer, turn off the power and unplug the computer’s power cord from the electrical outlet; then remove any dust from vents and perforations in the bezel. If you notice external dust accumulation, then examine and remove dust from the inside of the computer including heat sink inlet fins, power supply vents, and fans. Always turn off and unplug the computer before opening the cover. If possible, avoid operating your computer within 2 feet of high-traffic areas. If you must operate your computer in or near a high-traffic area, inspect and, if necessary, clean your computer more frequently.

For your safety and to maintain optimum computer performance, always follow these basic precautions with your desktop computer:

vKeep the cover closed whenever the computer is plugged in.

vRegularly inspect the outside of the computer for dust accumulation.

vRemove dust from vents and any perforations in the bezel. More frequent cleanings might be required for computers in dusty or high-traffic areas.

vDo not restrict or block any ventilation openings.

vDo not store or operate your computer inside furniture, as this might increase the risk of overheating.

vAirflow temperatures into the computer should not exceed 35° C (95° F).

x User Guide

v Do not use non-desktop air filtration devices.

Operating environment

The optimal environment in which to use your computer is 10°C-35°C (50°F-95°F) with humidity ranging between 35% and 80%. If your computer is stored or transported in temperatures less than 10°C (50°F), allow the cold computer to rise slowly to an optimal operating temperature of 10°C-35°C (50°F-95°F) before use. This process could take two hours in extreme conditions. Failure to allow your computer to rise to an optimal operating temperature before use could result in irreparable damage to your computer.

If possible, place your computer in a well-ventilated and dry area without direct exposure to sunshine.

Keep electrical appliances such as an electric fan, radio, high-powered speakers, air conditioner, and microwave oven away from your computer because the strong magnetic fields generated by these appliances can damage the monitor and data on the hard disk drive.

Do not place any beverages on top of or beside the computer or other attached devices. If liquid is spilled on or in the computer or an attached device, a short circuit or other damage might occur.

Do not eat or smoke over your keyboard. Particles that fall into your keyboard can cause damage.

Electrical current safety information

Danger

Electrical current from power, telephone, and communication cables is hazardous.

To avoid a shock hazard:

vTo prevent possible shock hazard, do not use your computer during a lightning storm.

vDo not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm.

vConnect all power cords to a properly wired and grounded electrical outlet.

vConnect to properly wired outlets any equipment that will be attached to this product.

vWhen possible, use one hand only to connect or disconnect signal cables.

vNever turn on any equipment when there is evidence of fire, water, or structural damage.

vDisconnect the attached power cords, telecommunications systems, networks, and modems before you open the device covers, unless instructed otherwise in the installation and configuration procedures.

vConnect and disconnect cables as described in the following table when installing, moving, or opening covers on this product or attached devices.

Important safety information

xi

To connect:

To disconnect:

1.

Turn everything OFF.

1.

Turn everything OFF.

2.

First, attach all cables to devices.

2.

First, remove power cords from outlet.

3.

Attach signal cables to connectors.

3.

Remove signal cables from connectors.

4.

Attach power cords to outlet.

4.

Remove all cables from devices.

5.

Turn device ON.

 

 

 

 

 

 

Lithium battery notice

Caution

Danger of explosion if battery is incorrectly replaced.

When replacing the lithium coin cell battery, use only the same or an equivalent type that is recommended by the manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of.

Do not:

vThrow or immerse into water

vHeat to more than 100°C (212°F)

vRepair or disassemble

Dispose of the battery as required by local ordinances or regulations.

The following statement applies to users in the state of California, U.S.A.

Perchlorate material: Special handling may apply. See

www.dtsc.ca.gov/hazardouswaste/perchlorate.

Modem safety information

Caution

To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.

To reduce the risk of fire, electrical shock, or injury when using telephone equipment, always follow basic safety precautions, such as:

vNever install telephone wiring during a lightning storm.

vNever install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

vNever touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

vUse caution when installing or modifying telephone lines.

vAvoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

vDo not use the telephone to report a gas leak in the vicinity of the leak.

xii User Guide

Laser compliance statement

Some personal computer models are equipped from the factory with a CD or DVD drive. CD and DVD drives are also sold separately as options. CD and DVD drives are laser products. These drives are certified in the U.S. to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1 laser products. Elsewhere, these drives are certified to conform to the requirements of the International Electrotechnical Commission (IEC) 60825-1 and CENELEC EN 60 825-1 for Class 1 laser products.

When a CD or DVD drive is installed, note the following handling instructions.

Caution

Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure.

Do not remove the drive covers. Removing the covers of the CD or DVD drive could result in exposure to hazardous laser radiation. There are no serviceable parts inside the CD or DVD drive.

Some CD and DVD drives contain an embedded Class 3A or Class 3B laser diode. Note the following statement.

Danger

Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam.

Power supply statement

Never remove the cover on a power supply or any part that has the following label attached.

Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician.

Products with television tuner options installed

The notice below applies to products containing television (TV) tuner devices that connect to external antennas or to cable/CATV systems, or both, and that are intended to be installed in North America. Users and installers in other countries should follow local codes and ordinances when installing appliances that connect to external antennas and cable/CATV systems. If local codes are not applicable, it is recommended that users/installers follow guidelines similar to those that follow.

Important safety information xiii

Note to CATV system installer

This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National Electrical Code (NEC) that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close as possible to the point of cable entry as practical.

Example of antenna grounding

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

Ground clamp

5

Power service grounding electrode system (NEC

 

 

 

 

 

 

 

 

 

 

Article 250, Part H)

2

Antenna lead-in wire

6

Ground clamps

3

Antenna discharge unit (NEC

7

Electronic service equipment

 

Section 810-20)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

Grounding conductors (NEC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Section 810-21

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 1. Proper grounding for the cable

xiv User Guide

The following notice applies to all countries and regions:

Danger

Outdoor antenna grounding

If an outside antenna or cable system is connected to the equipment, be sure the antenna or cable system is grounded as to provide some protection against voltage surges and built-up static charges.

Lightning

For added protection for this equipment during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the video product due to lightning and power line surges.

Power lines

An outside antenna system should not be located in the vicinity of overhead power lines or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them may be fatal.

Data safety

Do not delete unknown files or change the name of files or directories that were not created by you; otherwise, your computer software might fail to work.

Be aware that accessing network resources can leave your computer vulnerable to computer viruses, hackers, spyware, and other malicious activities that might damage your computer, software, or data. It is your responsibility to ensure that you have adequate protection in the form of firewalls, antivirus software, and anti-spyware software and keep this software up to date.

Cleaning and maintenance

Keep your computer and workspace clean. Shut down the computer and then disconnect the power cord before cleaning the computer. Do not spray any liquid detergent directly on the computer or use any detergent containing flammable material to clean the computer. Spray the detergent on a soft cloth and then wipe the computer surfaces.

Using headphones or earphones

If your computer has both a headphone connector and an audio-out connector, always use the headphone connector for headphones (also called a headset) or earphones.

Excessive use of headphones or earphones for a long period of time at high volume can be dangerous if the headphones or earphones do not comply with specifications of EN 50332-2. The headphone output connector of your computer

Important safety information

xv

complies with EN 50332-2 Sub clause 5.1. This specification limits the computer’s maximum wide band true RMS output voltage to 150mV. To help protect against hearing loss, ensure that the headphones or earphones you use also comply with EN 50332-2 (Sub clause 6.1) for a wide band characteristic voltage of 75mV. Using headphones that do not comply with EN 50332-2 can be dangerous due to excessive sound pressure levels.

If your Lenovo computer came with headphones or earphones in the package, as a set, the combination of the headphones or earphones and the computer already complies with the specifications of EN 50332-1. If different headphones or earphones are used, ensure that they comply with EN 50332-2. (Sub clause 6.1) for a wide band characteristic voltage of 75mV. Using headphones that do not comply with EN 50332-2 can be dangerous due to excessive sound pressure levels.

Additional safety information

Plastic bags can be dangerous. Keep plastic bags away from babies and children to avoid danger of suffocation.

xvi User Guide

Introduction

This User Guide contains the following information:

vChapter 1, “Arranging your workspace,” on page 1 provides information about setting up your computer for comfort and the impact of light sources, air circulation, and electrical outlets.

vChapter 2, “Setting up your computer,” on page 3 provides information about setting up your computer and software and operating system installation.

vChapter 3, “Installing options,” on page 13 provides information on the features and options that are available for your computer.

vChapter 4, “Recovering software,” on page 41 provides instructions on how to use the ThinkVantage® Rescue and Recoveryprogram to create product recovery disks, back up data, recover software, and restore the entire contents of your hard disk to a previously saved state.

vChapter 5, “Using the Setup Utility,” on page 49 provides instructions on how to view and change the configuration settings of your computer.

vChapter 6, “Updating system programs,” on page 53 provides information about updating POST/BIOS and how to recover from a POST/BIOS update failure.

vChapter 7, “Troubleshooting and diagnostics,” on page 55 provides information about basic troubleshooting and diagnostic tools for your computer.

vChapter 8, “Getting information, help, and service,” on page 61 provides information about the wide variety of helpful resources available from Lenovo.

vAppendix A, “Manual modem commands,” on page 65 provides commands for manually programming your modem.

vAppendix B, “Notices,” on page 73 provides notices and trademark information.

© Lenovo 2006, 2007. Portions © IBM Corp. 2005.

xvii

xviii User Guide

Chapter 1. Arranging your workspace

To get the most from your computer, arrange both the equipment you use and your work area to suit your needs and the kind of work you do. Your comfort is of foremost importance, but light sources, air circulation, and the location of electrical outlets also can affect the way you arrange your workspace.

Comfort

Although no single working position is ideal for everyone, here are a few guidelines to help you find a position that suits you best.

Sitting in the same position for a long time can cause fatigue. A good chair can make a big difference. The backrest and seat should adjust independently and provide good support. The seat should have a curved front to relieve pressure on the thighs. Adjust the seat so that your thighs are parallel to the floor and your feet are either flat on the floor or on a footrest.

When using the keyboard, keep your forearms parallel to the floor and your wrists in a neutral, comfortable position. Try to keep a light touch on the keyboard and your hands and fingers relaxed. You can change the angle of the keyboard for maximum comfort by adjusting the position of the keyboard feet.

Viewing Distance

Lower

Back

Support

Seat

Height

Adjust the monitor so the top of the screen is at, or slightly below, eye level. Place the monitor at a comfortable viewing distance, usually 51 to 61 cm (20 to 24 in.), and position it so you can view it without having to twist your body. Also position other equipment you use regularly, such as the telephone or a mouse, within easy reach.

Glare and lighting

Position the monitor to minimize glare and reflections from overhead lights, windows, and other light sources. Even reflected light from shiny surfaces can cause annoying reflections on your monitor screen. Place the monitor at right angles to windows and other light sources, when possible. Reduce overhead lighting, if necessary, by turning off lights or using lower wattage bulbs. If you install the monitor near a window, use curtains or blinds to block the sunlight. You might have to adjust the brightness and contrast controls on the monitor as the room lighting changes throughout the day.

© Lenovo 2006, 2007. Portions © IBM Corp. 2005.

1

Where it is impossible to avoid reflections or to adjust the lighting, an antiglare filter placed over the screen might be helpful. However, these filters might affect the clarity of the image on the screen; try them only after you have exhausted other methods of reducing glare.

Dust buildup compounds problems associated with glare. Remember to clean your monitor screen periodically using a soft cloth moistened with a nonabrasive liquid glass cleaner.

Air circulation

Your computer and monitor produce heat. The computer has a fan that pulls in fresh air and forces out hot air. The monitor lets hot air escape through vents. Blocking the air vents can cause overheating, which might result in a malfunction or damage. Place the computer and monitor so that nothing blocks the air vents; usually, 51 mm (2 in.) of air space is sufficient. Also, make sure the vented air is not blowing on someone else.

Electrical outlets and cable lengths

The location of electrical outlets and the length of power cords and cables that connect to the monitor, printer, and other devices might determine the final placement of your computer.

When arranging your workspace:

vAvoid the use of extension cords. When possible, plug the computer power cord directly into an electrical outlet.

vKeep power cords and cables neatly routed away from walkways and other areas where they might get kicked accidentally.

For more information about power cords, see “Power cords and power adapters” on page vii and the safety and warranty information that is provided with your computer.

2 User Guide

Chapter 2. Setting up your computer

Before you begin, make sure you set up your computer in the best possible work area that suits your needs and the kind of work you do. For more information, refer to Chapter 1, “Arranging your workspace,” on page 1.

Note: Read “Important safety information” on page v before you set up your computer. The precautions and guidelines will help you work safely.

Installing the vertical stand

A vertical stand can be used to place your computer in the vertical position. If your computer comes with a vertical stand, do the following to install the stand:

1.Position your computer in the vertical position with the air vents facing downward.

2.Align the tab on the vertical stand with the notch on the computer as shown.

3.Pivot the vertical stand towards the front of the computer until it snaps into position.

© Lenovo 2006, 2007. Portions © IBM Corp. 2005.

3

4.Carefully, position the computer with the air vents facing upward so that the computer sits on the vertical stand as shown.

Connecting your computer

Use the following information when connecting your computer. Look for the small connector icons on the back of your computer.

Important

Setting the voltage-selection switch incorrectly can cause permanent damage to the computer.

If you are not sure of the voltage provided at your electrical outlet, contact your local electric company or refer to official Web sites or other literature for travelers to the country or region where you are located.

Note: Your computer might not have all of the switches or connectors described in this section.

If your computer cables and connector panel have color-coded connectors, match the color of the cable end with the color of the connector. For example, match a blue cable end with a blue connector or a red cable end with a red connector.

4 User Guide

1.Some models are equipped with a voltage-selection switch located near the power-cord connection point on the computer.

If your computer has a voltage-selection switch, ensure that you set the voltage-selection switch to match the voltage available at your electrical outlet. If necessary, use a ballpoint pen to slide the switch to a different position.

vIf the voltage supply range in your local country or region is 100–127 V ac, set the switch to 115 V.

vIf the voltage supply range is in your local country or region is 200–240 V ac, set the switch to 230 V.

115

If your computer does not have a voltage selection switch, it is designed to operate only at the voltage provided in the country or region where it was originally purchased. Continue with step 2.

2.Your keyboard cable might have a standard keyboard connector 1 or a Universal Serial Bus (USB) connector 2. Connect the keyboard cable to the appropriate keyboard connector.

Note: Some models will have keyboards with a fingerprint reader. After you setup and turn on your computer, refer to the Access Help online help system for information about your fingerprint reader. See “Access Help” on page 62 for instructions on how to open the online help system.

Chapter 2. Setting up your computer 5

3.Your mouse cable might have a standard mouse connector 1 or a USB connector 2. Connect the mouse cable to the appropriate mouse connector.

4.Connect the monitor cable to the monitor connector on the computer.

v If you have a Video Graphics Array (VGA) Standard monitor, connect the cable to the connector as shown.

Note: If your model has two monitor connectors, be sure to use the connector on the accelerated graphics port (AGP) adapter.

6 User Guide

vIf you have a digital video interface (DVI) monitor, connect the cable to the connector as shown.

Note: Your computer must have an adapter installed that supports the DVI monitor.

5. If you have a modem, connect the modem using the following information.

PHONE

LINE

PHONE

PHONE

 

LINE

PHON

E

 

LINE

 

LINE

 

1 This illustration shows the two connections on the back of the computer that are needed to set up your modem.

2 In the United States and other countries or regions that use the RJ-11 telephone outlet, attach one end of the telephone cable to the telephone and the other end to the telephone connector on the back of the computer. Attach one end of the modem cable to the modem connector on the back of the computer and the other end to the telephone outlet.

3 In countries or regions that do not use RJ-11 telephone outlets, a splitter or converter is required to attach the cables to the telephone outlet, as shown at the top of the illustration. You also can use the splitter or converter without the telephone, as shown at the bottom of the illustration.

Chapter 2. Setting up your computer 7

6.If you have audio devices, attach them using the following instructions. For more information about speakers, see steps 7 and 8.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 Audio line-in

This connector receives audio signals from an external audio device,

 

 

 

 

such as a stereo system.

2 Audio line-out

This connector sends audio signals from the computer to external

 

 

 

 

devices, such as powered stereo speakers.

3 Microphone

Use this connector to attach a microphone to your computer when

 

 

 

 

you want to record sound or if you use speech-recognition software.

4 Headphone

Use this connector to attach headphones to your computer when you

 

 

 

 

want to listen to music or other sounds without disturbing anyone.

 

 

 

 

This connector might be located on the front of the computer.

7.If you have powered speakers with an ac adapter, use the following instructions.

a.Connect the cable that runs between the speakers, if necessary. On some speakers, this cable is permanently attached.

b.Connect the ac adapter cable to the speaker.

c.Connect the speakers to the computer.

d.Connect the ac adapter to the ac power source.

8.If you have unpowered speakers with no ac adapter, use the following instructions.

a.Connect the cable that runs between the speakers, if necessary. On some speakers, this cable is permanently attached.

8 User Guide

Lenovo 9266, 9384, 6491, 8972, 9649 User Manual

b. Connect the speakers to the computer.

9.Connect any additional devices that you have. Your computer might not have all connectors that are shown.

1394

1394

1 USB

Use this connector to attach a device that requires a USB connection,

 

such as a keyboard, mouse, scanner, printer, or personal digital

 

assistant (PDA).

2 Serial

Use this connector to attach an external modem, serial printer, or

 

other device that uses a 9-pin serial connector.

3 S-video

Use this connector to attach a television set that has an S-Video

 

connector. This connector is present on some high-performance video

 

adapters.

4 Parallel

Use this connector to attach a parallel printer or any other device that

 

requires a 25-pin parallel connection.

5 Ethernet

Use this connector to attach the computer to an Ethernet-type local

 

area network or to a cable modem.

 

Important: To operate the computer within FCC limits when it is

 

connected to an Ethernet network, use a Category 5 Ethernet cable.

6 MIDI/joystick

Use this connector to attach a joystick, gamepad, or a musical

 

instrument digital interface (MIDI) device such as a MIDI keyboard.

7 IEEE 1394

This connector is sometimes called Firewire because it transmits data

 

rapidly. There are two types of IEEE 1394 connectors: the 4-pin and

 

the 6-pin. IEEE 1394 offers connection to several types of consumer

 

electronics, including digital audio devices and scanners.

10. Connect the power cords to properly grounded electrical outlets.

Chapter 2. Setting up your computer 9

Note: Refer to the Access Help online help system for more information about connectors. See “Access Help” on page 62 for instructions on how to open the online help system.

Turning on power

Turn on the monitor and other external devices first, and then turn on the computer. When the power-on self-test (POST) is finished, the logo window closes. If your computer has preinstalled software, the software installation program starts.

If you experience any problems during startup, see Chapter 7, “Troubleshooting and diagnostics,” on page 55. For additional help, refer to Chapter 8, “Getting information, help, and service,” on page 61. You can get help and information by telephone through the Customer Support Center. Refer to the safety and warranty information that is provided with your computer for the Service and Support worldwide telephone list.

Finishing the software installation

Important

Read the license agreements carefully before using the programs on this computer. These agreements detail your rights, obligations, and warranties for the software on this computer. By using these programs, you accept the terms of the agreements. If you do not accept the agreements, do not use the programs. Instead, promptly return the entire computer for a full refund.

After you start the computer for the first time, follow the instructions on the screen to complete the software installation. If you do not complete the software installation the first time the computer is turned on, unpredictable results might occur. When the installation is complete, refer to the Access Help online help system to learn more about your computer. See “Access Help” on page 62 for instructions on how to open the online help system.

Note: Some models might have a multilingual version of the Microsoft® Windows® operating system preinstalled. If your computer has the multilingual version, you will be prompted to choose a language during the initial installation process. After installation, the language version can be changed through the Windows Control Panel.

Completing important tasks

After you have set up your computer, perform the following tasks, which will save you time and trouble later:

vCreate a diagnostic CD image, diagnostic diskettes, or rescue media. Diagnostic programs are used to test hardware components of your computer and report operating-system-controlled settings that can cause hardware failures. Making a diagnostic CD image, diagnostic diskettes, or rescue media ahead of time assures that you will be able to run diagnostics if the Rescue and Recovery workspace becomes inaccessible. For more information, see “PC-Doctor for DOS” on page 57 or “PC-Doctor for Windows PE” on page 59.

10 User Guide

Loading...
+ 68 hidden pages