ThinkServer
Hardware Maintenance Manual
Machine Types: 0387, 0388, 0389, 0390, 0391, 0392, 0393, and 0441
Note:
Before using the information and the product it supports, be sure to read and understand the following:
•The Read Me First that comes with your product
•“Safety information” on page iii
•Appendix A “Notices” on page 217
Second Edition (August 2011)
© Copyright Lenovo 2011.
LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
Contents
Safety information . . . . . . . . . . |
|
iii |
Chapter 1. General information . . . . |
. |
1 |
Introduction . . . . . . . . . . . . . . . . |
. |
1 |
Server documentation. . . . . . . . . . . . |
. |
1 |
Chapter 2. Server setup road map . . |
. |
5 |
Chapter 3. Product overview . . . . . |
. |
7 |
Server package . . . . . . . . . . . . . . |
. |
7 |
Features . . . . . . . . . . . . . . . . . |
. |
7 |
Specifications . . . . . . . . . . . . . . . |
|
12 |
Software . . . . . . . . . . . . . . . . . |
|
12 |
ThinkServer EasyStartup . . . . . . . . . |
|
12 |
ThinkServer EasyUpdate Firmware Updater . |
|
13 |
BIOS and BMC firmware update utility . . . |
|
13 |
RAID configuration utilities . . . . . . . . |
|
13 |
PC-Doctor for DOS . . . . . . . . . . . |
|
13 |
Locations. . . . . . . . . . . . . . . . . |
|
13 |
Machine type, model, and serial number |
|
|
label . . . . . . . . . . . . . . . . . |
|
13 |
Front view of the server . . . . . . . . . |
|
15 |
Front panel . . . . . . . . . . . . . . |
|
17 |
DIT module . . . . . . . . . . . . . . |
|
18 |
Rear view of the server . . . . . . . . . |
|
19 |
Server locks . . . . . . . . . . . . . . |
|
22 |
Server components . . . . . . . . . . . |
|
25 |
Hot-swap hard disk drive status LEDs . . . |
|
32 |
RAID card. . . . . . . . . . . . . . . |
|
33 |
Hot-swap hard disk drive backplane . . . . |
|
34 |
System board components . . . . . . . . |
|
42 |
System board jumpers . . . . . . . . . . |
|
46 |
System board LEDs . . . . . . . . . . . |
|
50 |
Chapter 4. Turning on and turning off |
|
|
the server . . . . . . . . . . . . . . . |
|
53 |
Turning on the server . . . . . . . . . . . . |
|
53 |
Turning off the server . . . . . . . . . . . . |
|
53 |
Chapter 5. Configuring the server . . |
|
55 |
Using the Setup Utility program . . . . . . . . |
|
55 |
Starting the Setup Utility program . . . . . |
|
55 |
Viewing information in the Setup Utility |
|
|
program . . . . . . . . . . . . . . . |
|
55 |
Setup Utility program interface . . . . . . |
|
56 |
Setting the system date and time . . . . . |
|
64 |
Using passwords . . . . . . . . . . . . |
|
65 |
Configuring the TPM function . . . . . . . |
|
66 |
Selecting a startup device . . . . . . . . |
66 |
Exiting the Setup Utility program . . . . . . |
67 |
Updating or recovering the BIOS. . . . . . |
67 |
Using the ThinkServer EasyStartup program . . . |
69 |
Features of the ThinkServer EasyStartup |
|
program . . . . . . . . . . . . . . . |
70 |
Starting the ThinkServer EasyStartup |
|
program . . . . . . . . . . . . . . . |
70 |
Configuring RAID. . . . . . . . . . . . . . |
71 |
About RAID . . . . . . . . . . . . . . |
72 |
RAID for your server. . . . . . . . . . . |
73 |
Configuring RAID using the ThinkServer |
|
EasyStartup program . . . . . . . . . . |
74 |
Configuring the onboard SATA software |
|
RAID . . . . . . . . . . . . . . . . . |
74 |
Configuring the advanced SATA or SAS |
|
hardware RAID . . . . . . . . . . . . . |
79 |
Configuring the Ethernet controllers . . . . . . |
80 |
Updating the firmware. . . . . . . . . . . . |
80 |
Using the Firmware Updater program . . . . |
81 |
Chapter 6. Installing, removing, or |
|
replacing hardware . . . . . . . . . . |
83 |
Guidelines . . . . . . . . . . . . . . . . |
83 |
Precautions . . . . . . . . . . . . . . |
83 |
Handling static-sensitive devices . . . . . |
84 |
System reliability guidelines . . . . . . . . |
84 |
Working inside the server with the power on . |
85 |
Removing the server cover . . . . . . . . . . |
85 |
Removing and reinstalling the front bezel . . . . |
87 |
Installing, removing, or replacing hardware . . . |
89 |
Installing or removing a memory module. . . |
89 |
Installing or removing a PCI card . . . . . . |
93 |
Installing or removing the Ethernet card . . . |
96 |
Installing or removing the RAID card . . . . |
98 |
Installing or removing the ThinkServer 9240-8i |
|
RAID 5 Upgrade Key . . . . . . . . . . |
100 |
Installing or removing the ThinkServer SATA |
|
Software RAID 5 Key . . . . . . . . . . |
102 |
Installing or removing the ThinkServer iKVM |
|
Remote Management Module . . . . . . . |
105 |
Installing or removing the TPM module . . . |
109 |
Installing or removing the DIT module . . . . 111 |
|
Installing or replacing an optical drive . . . . 115 |
|
Installing or replacing a hot-swap hard disk |
|
drive . . . . . . . . . . . . . . . . . |
119 |
Removing or installing a non-hot-swap hard |
|
disk drive . . . . . . . . . . . . . . . |
123 |
© Copyright Lenovo 2011 |
i |
Replacing the hot-swap hard disk drive |
|
backplane. . . . . . . . . . . . . . . |
133 |
Replacing the non-hot-swap power supply |
|
assembly . . . . . . . . . . . . . . . |
137 |
Replacing a hot-swap redundant power |
|
supply module . . . . . . . . . . . . . |
140 |
Replacing the power distribution board and |
|
cage assembly . . . . . . . . . . . . . |
143 |
Replacing the front panel board assembly . . |
147 |
Replacing the front system fan . . . . . . |
149 |
Replacing the rear system fan . . . . . . . |
152 |
Replacing the heat sink and fan assembly . . |
154 |
Replacing the microprocessor . . . . . . . |
157 |
Replacing the system board battery . . . . |
161 |
Replacing the system board . . . . . . . |
162 |
Completing the parts replacement . . . . . . . |
168 |
Reinstalling the server cover and reconnecting |
|
cables . . . . . . . . . . . . . . . . |
168 |
Updating the server configuration . . . . . |
170 |
Chapter 7. Troubleshooting and diagnostics . . . . . . . . . . . . . 171
Troubleshooting procedure . . . . . . . . . . 171
Viewing the status and diagnostic LEDs. . . . . 171
Using the diagnostic program . . . . . . . . . |
172 |
Viewing the system event log . . . . . . . . . |
172 |
Basic troubleshooting tables . . . . . . . . . |
172 |
ThinkServer EasyStartup program |
|
problems . . . . . . . . . . . . . . . |
172 |
Optical drive problems. . . . . . . . . . |
173 |
Hard disk drive problems . . . . . . . . . |
174 |
Memory module problems . . . . . . . . |
176 |
Keyboard, mouse, or USB device problems . . |
176 |
POST error codes. . . . . . . . . . . . |
177 |
Chapter 8. FRU lists . . . . . . . . . |
179 |
Major FRUs . . . . . . . . . . . . . . . . |
179 |
Mechanical FRUs . . . . . . . . . . . . . |
189 |
Adapters and miscellaneous FRUs . . . . . . . |
194 |
Power cords . . . . . . . . . . . . . . . |
196 |
Shipgroup . . . . . . . . . . . . . . . . |
204 |
Chapter 9. Getting information, help, |
|
and service . . . . . . . . . . . . . |
213 |
Information resources . . . . . . . . . . . . |
213 |
Using the documentation. . . . . . . . . |
213 |
ThinkServer Web site |
|
(http://www.lenovo.com/thinkserver) . . . . |
213 |
Lenovo Support Web site. . . . . . . . . |
213 |
Help and service . . . . . . . . . . . . . . |
214 |
Before you call . . . . . . . . . . . . . |
214 |
Calling for service. . . . . . . . . . . . |
214 |
Using other services . . . . . . . . . . |
215 |
Purchasing additional services . . . . . . |
215 |
Appendix A. Notices. . . . . . . . |
. |
217 |
Trademarks . . . . . . . . . . . . . . |
. . |
218 |
Important notes . . . . . . . . . . . . |
. . |
218 |
Polyvinyl Chloride (PVC) cable and cord notice |
. . |
218 |
Recycling information . . . . . . . . . . |
. . |
218 |
Battery return program. . . . . . . . |
. . |
219 |
Requirement for batteries containing |
|
|
perchlorate . . . . . . . . . . . . |
. . |
220 |
Particulate contamination . . . . . . . . |
. . |
220 |
Important information for the European Directive |
|
|
2002/96/EC . . . . . . . . . . . . . . |
. . |
221 |
Restriction of Hazardous Substances Directive |
|
|
(RoHS) . . . . . . . . . . . . . . . . |
. . |
224 |
China RoHS . . . . . . . . . . . . |
. . |
225 |
Turkish statement of compliance . . . . |
. . |
225 |
German Ordinance for Work gloss statement. |
. . |
226 |
Electronic emission notices. . . . . . . . |
. . |
226 |
Federal Communications Commission (FCC) |
|
|
Statement. . . . . . . . . . . . . |
. . |
226 |
Index. . . . . . . . . . . . . . . . |
. |
229 |
ii ThinkServer Hardware Maintenance Manual
Note: Before using the product, be sure to read and understand the multilingual safety instructions on the documentation DVD that comes with the product.
Antes de usar o produto, leia e entenda as instruções de segurança multilíngues no DVD de documentação que o acompanha.
Преди да използвате този продукт, задължително прочетете и вникнете в многоезичните инструкции за безопасност в DVD диска с документация, който се предоставя с продукта.
Prije upotrebe ovog proizvoda obavezno pročitajte višejezične sigurnosne upute koje se nalaze na DVD-u s dokumentacijom koji dobivate uz proizvod.
Před použitím produktu je třeba si přečíst a porozumět bezpečnostním pokynům uvedeným na disku DVD s dokumentací, který je dodáván s produktem.
Før du bruger produktet, skal du sørge for at læse og forstå de sikkerhedsforskrifter, der findes på flere sprog, på den dokumentations-dvd, der følger med produktet.
Lue tuotteen mukana toimitetulla DVD-tietolevyllä olevat monikieliset turvaohjeet ennen tämän tuotteen käyttöä.
Avant d'utiliser le produit, veillez à bien lire et comprendre les instructions de sécurité multilingues figurant sur le DVD de documentation fourni avec le produit.
Πριν χρησιμοποιήσετε το προϊόν, βεβαιωθείτε ότι έχετε διαβάσει και κατανοήσει τις οδηγίες ασφάλειας, οι οποίες είναι διαθέσιμες σε διάφορες γλώσσες στο DVD τεκμηρίωσης που συνοδεύει το προϊόν.
Vor Verwendung des Produkts sollten Sie unbedingt die mehrsprachigen Sicherheitsanweisungen auf der Dokumentations-DVD lesen, die im Lieferumfang des Produkts enthalten ist.
A termék használata előtt mindenképpen olvassa el és értelmezze a termékhez kapott dokumentációs DVD lemezen található, több nyelven elolvasható biztonsági előírásokat.
Prima di utilizzare il prodotto, accertarsi di leggere e comprendere le informazioni sulla sicurezza multilingue disponibili sul DVD di documentazione fornito con il prodotto.
Documentation DVD
DVD .
Voordat u het product gebruikt, moet u ervoor zorgen dat u de meertalige veiligheidsinstructies op de documentatie-dvd van het product hebt gelezen en begrijpt.
© Copyright Lenovo 2011 |
iii |
Przed skorzystaniem z produktu należy zapoznać się z wielojęzycznymi instrukcjami bezpieczeństwa znajdującymi się na płycie DVD z dokumentacją dostarczoną wraz z produktem.
Antes de utilizar o produto, leia atentamente as instruções de segurança multilingues que constam no DVD de documentação fornecido com o produto.
Înainte de a utiliza produsul, asiguraţi-vă că aţi citit şi înţeles instrucţiunile de siguranţă în mai multe limbi de pe DVD-ul cu documentaţie care însoţeşte produsul.
Før du bruker produktet, må du lese og forstå den flerspråklige sikkerhetsinformasjonen på DVDen med dokumentasjon som følger med produktet.
Прежде чем использовать этот продукт, внимательно ознакомьтесь с инструкциями по технике безопасности на разных языках, которые можно найти на DVD-диске с документацией в комплекте с продуктом.
DVD
Pre nego to upotrebite proizvod obavezno paljivo proitajte i prouite viejeziko uputstvo za bezbednost na dokumentacionom DVD-u koji ste dobili uz proizvod.
Pred pouvanm produktu si pretajte viacjazyn bezpenostn pokyny na disku DVD s dokumentciou dodanom s produktom.
Preden začnete uporabljati izdelek, je pomembno, da preberete in razumete večjezična varnostna navodila na DVD-ju z dokumentacijo, ki ste ga prejeli skupaj z izdelkom.
Antes de utilizar el producto, asegúrese de leer y comprender las instrucciones de seguridad multilingües del DVD de documentación que se proporciona con el producto.
Var noga med att läsa säkerhetsinstruktionerna på dokumentations-DVD-skivan som följer med produkten innan du börjar använda produkten.
DVD
Bu ürünü kullanmadan önce, ürünle birlikte gönderilen belge DVD'si üzerindeki çok dil içeren güvenlik yönergelerini okuyup anladýðýnýzdan emin olun.
Перед використанням цього продукту уважно ознайомтеся з інструкціями з техніки безпеки на різних мовах, що можна знайти на DVD-диску з документацією в комплекті з продуктом.
Important: The caution and danger statements in this document are labeled with numbers. Each number identifies an English-language caution or danger statement that refers to translated versions of the caution or danger statement in the Safety Information document. For example, if a danger statement is labeled “Statement 1,” translations for this danger statement are in the Safety Information document under “Statement 1.”
Ensure that you read and understand all caution and danger statements in this document before you perform the procedures. Read and understand any additional safety information that is included with the server or optional device before you install, remove, or replace the device.
iv ThinkServer Hardware Maintenance Manual
Statement 1
DANGER
Electrical current from power, telephone, and communication cables is hazardous.
To avoid a shock hazard:
•Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm.
•Connect all power cords to a properly wired and grounded electrical outlet.
•Connect to properly wired outlets any equipment that will be attached to this product.
•When possible, use one hand only to connect or disconnect signal cables.
•Never turn on any equipment when there is evidence of fire, water, or structural damage.
•Disconnect the attached power cords, telecommunications systems, networks, and modems before you open the device covers, unless instructed otherwise in the installation and configuration procedures.
•Connect and disconnect cables as described in the following table when installing, moving, or opening covers on this product or attached devices.
To connect: |
To disconnect: |
||
1. |
Turn everything OFF. |
1. |
Turn everything OFF. |
2. |
First, attach all cables to devices. |
2. |
First, remove power cords from outlet. |
3. |
Attach signal cables to connectors. |
3. |
Remove signal cables from connectors. |
4. |
Attach power cords to outlet. |
4. |
Remove all cables from devices. |
5. |
Turn devices ON. |
|
|
|
|
|
|
Statement 2
DANGER
Danger of explosion if battery is incorrectly replaced.
When replacing the lithium coin cell battery, use only the same or an equivalent type that is recommended by the manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of.
Do not:
•Throw or immerse into water
•Heat to more than 100°C (212°F)
•Repair or disassemble
Dispose of the battery as required by local ordinances or regulations.
© Copyright Lenovo 2011 |
v |
Statement 3
CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following:
•Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device.
•Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure.
DANGER
Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following.
Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam.
Statement 4
≥ 18 kg (39.7 lb) |
≥ 32 kg (70.5 lb) |
≥ 55 kg (121.2 lb) |
< 32 kg (70.5 lb) |
< 55 kg (121.2 lb) |
< 100 kg (220.5 lb) |
CAUTION:
Use safe practices when lifting.
Statement 5
CAUTION:
The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.
vi ThinkServer Hardware Maintenance Manual
Statement 6
CAUTION:
If you install a strain-relief bracket option over the end of the power cord that is connected to the device, you must connect the other end of the power cord to a power source that is easily accessible in case it needs to be disconnected.
Statement 7
CAUTION:
If the device has doors, ensure that you remove or secure the doors before moving or lifting the device to protect against personal injury. The doors will not support the weight of the device.
Statement 8
CAUTION:
Never remove the cover on a power supply or any part that has the following label attached.
Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician.
Statement 9
CAUTION:
Disconnect the hot-swap fan cables before removing the fan from the device to protect against personal injury.
Statement 10
CAUTION:
The following label indicates a sharp-edge hazard.
© Copyright Lenovo 2011 |
vii |
Statement 11
CAUTION:
The following label indicates a potential heat hazard.
Statement 12
DANGER
Overloading a branch circuit is a potential fire hazard and a shock hazard under certain conditions. To avoid these hazards, ensure that your system electrical requirements do not exceed branch current ratings at the installation site.
Statement 13
CAUTION:
Ensure that the rack is secured properly to avoid tipping when the server unit is extended on the rails.
Statement 14
CAUTION:
Some accessory or option board outputs exceed Class 2 or limited power source limits. You must install the appropriate interconnecting cabling in accordance with your local electrical code requirements.
Statement 15
CAUTION:
The power-control button on the device may put the device in standby mode instead of turning off the device. In addition, the device might have multiple connections to dc power. To remove all electrical current from the device, ensure that all connections to dc power are disconnected at the dc power input terminals.
viii ThinkServer Hardware Maintenance Manual
Statement 16
CAUTION:
To reduce the risk of electric shock or energy hazards:
•This equipment must be installed by trained service personnel in a restricted-access location, as defined by your local electrical code and the latest edition of IEC 60950.
•Connect the equipment to a reliably earthed safety extra low voltage (SELV) source. An SELV source is a secondary circuit that is designed so that normal and single fault conditions do not cause the voltages to exceed a safe level (60 V direct current).
•The branch circuit overcurrent protection must be rated in accordance with local electrical code requirements.
•Use 1.3 mm2 or 16 American Wire Gauge (AWG) copper conductor only, not exceeding 3 meters in length.
•Torque the wiring-terminal screws to 1.4 newton-meters or 12 inch-pounds.
•Provide a readily available, approved and rated disconnect device in the field wiring.
Statement 17
CAUTION:
This product contains a Class 1M laser. Do not view directly with optical instruments.
Statement 18
CAUTION:
Do not place any object on top of rack-mounted products.
Statement 19
CAUTION:
Hazardous moving parts. Keep fingers and other body parts away.
© Copyright Lenovo 2011 |
ix |
Statement 20
CAUTION:
A lithium ion battery is provided. To avoid possible explosion, do not burn the battery. Replace the battery only with the Lenovo-approved part. Recycle or discard the battery as instructed by local regulations.
x ThinkServer Hardware Maintenance Manual
This chapter provides some general information about your product.
This chapter contains the following items:
•“Introduction” on page 1
•“Server documentation” on page 1
This Hardware Maintenance Manual for your Lenovo® ThinkServer® product contains information about the server features, specifications, component locations, configuration instructions, hardware replacement procedures, parts listing, and troubleshooting and diagnostics.
Note: The Hardware Maintenance Manual is intended only for trained service personnel of Lenovo. The Hardware Maintenance Manual is updated frequently, and the most up-to-date version is always available in English on the Lenovo Web site at:
http://www.lenovo.com/ThinkServerUserGuides
This document contains instructions on how to install, remove, or replace Customer Replaceable Units (CRUs) and Field Replaceable Units (FRUs).
Replaceable components are of three types:
•Self-service CRUs: Self-service CRUs are easy to install and customers are responsible for replacing all Self-service CRUs. If a Lenovo service technician installs a Self-service CRU at your request, you will be charged for the installation.
•Optional-service CRUs: Although dealing with Optional-service CRUs requires some technical skills, Optional-service CRUs are safe for customers to replace. You may install an Optional-service CRU yourself or request Lenovo to install it, at no additional charge, under the type of warranty service that is designated for the server.
•FRUs: FRUs must be replaced only by trained service technicians.
Notes:
1.Before servicing a Lenovo product, be sure to read and understand the “Safety information” on page iii.
2.For information about the terms of warranty, refer to the Warranty and Support Information on the documentation DVD that comes with the server. The Warranty and Support Information is also available on the Lenovo Web site at:
http://www.lenovo.com/ThinkServerUserGuides
To obtain the most up-to-date information about the server, go to:
http://www.lenovo.com/thinkserver
Lenovo maintains pages on the World Wide Web, where you can get the latest technical information and download documentation or device drivers and updates. To access the Lenovo Support Web site, go to: http://support.lenovo.com
This topic provides general descriptions of the various documentation for your server and instructions on how to obtain all the documentation.
© Copyright Lenovo 2011 |
1 |
Printed documents
The following documents are printed out and contained in your server package.
•Read Me First
This is a multilingual document you should read first. This document guides you to read the complete warranty, support, and safety information on the documentation DVD that comes with your server before using the product. This document also provides information about how to find the most up-to-date information on the Lenovo Support Web site.
•Important Notices
This document includes safety and legal notices that you should read and understand before using the server.
Documentation DVD
The documentation DVD, which comes with your server, contains various documents for your server in Portable Document Format (PDF). To view the documentation, you need to have the Adobe Reader program installed. You can download the desired language version of the latest Adobe Reader program from the Adobe Web site at:
http://www.adobe.com
Note: Lenovo maintains pages on the World Wide Web where you can get the latest technical information and download documentation or device drivers and updates. Some information in the documents on the documentation DVD might change without notice after the first release of the DVD. You can always obtain all the most up-to-date documentation for your server from the Lenovo Web site at: http://www.lenovo.com/ThinkServerUserGuides
The following documents are on the documentation DVD that comes with your server:
•Safety Information
This is a multilingual document that includes all the safety statements for your product in more than 30 languages. Be sure to read and understand all the safety statements before using the product.
•Warranty and Support Information
This document includes the Lenovo warranty statement, CRUs information, and information about how to contact Lenovo Support.
•User Guide
This document provides detailed information to help you get familiar with your server and help you use, configure, and maintain your server.
•Remote Management Module User Guide
This document provides information to help you use the integrated Keyboard, Video, and Mouse (iKVM) function for server remote management. This document is in English only.
Note: A ThinkServer iKVM Remote Management Module (hereinafter referred to as the iKVM key) is required and this option should be installed on the iKVM key connector on the system board to enable the iKVM function.
2 ThinkServer Hardware Maintenance Manual
•MegaRAID SAS Software User Guide
This document provides information about Redundant Array of Independent Disks (RAID) and how to use the utility programs to configure, monitor, and maintain your server RAID and related devices. This document is in English only.
Note: Refer to this document for hardware RAID information if you have a required RAID card installed in the server. See “Installing or removing the RAID card” on page 98. For information about the onboard SATA software RAID, see “Configuring the onboard SATA software RAID” on page 74.
Document for trained service personnel only
The following document is intended for trained service personnel of Lenovo and is only available in English on the Lenovo Web site at:
http://www.lenovo.com/ThinkServerUserGuides
Hardware Maintenance Manual
This document provides diagnostic information, parts listing, and replacement procedures for all field replaceable units (FRUs, parts replaced by trained service personnel) as well as all CRUs.
Chapter 1. General information 3
4 ThinkServer Hardware Maintenance Manual
This chapter provides a general road map to guide you through setting up your server.
The server setup procedure varies depending on the configuration of the server when it was delivered. In some cases, the server is fully configured and you just need to connect the server to the network and an ac power source, and then you can turn on the server. In other cases, the server needs to have hardware features installed, requires hardware and firmware configuration, and requires an operating system to
be installed.
The general procedure for setting up your server is:
1.Unpack the server package. See “Server package” on page 7.
2.Install any required hardware or server option. See the related topic in Chapter 6 “Installing, removing, or replacing hardware” on page 83.
3.Connect the Ethernet cable and power cord(s) to the server. See “Rear view of the server” on page 19 to locate the connectors.
4.Turn on the server to verify operation. See “Turning on the server” on page 53.
5.Review the Unified Extensible Firmware Interface (UEFI) settings and customize as needed. See “Using the Setup Utility program” on page 55.
6.Configure RAID and install the operating system and basic drivers. See “Using the ThinkServer EasyStartup program” on page 69 and “Configuring RAID” on page 71.
7.Install any additional drivers needed for added features. Refer to the instructions that come with the hardware option.
8.Configure Ethernet settings in the operating system by referring to the operating system help. This step is not required if the operating system was installed using the ThinkServer EasyStartup program.
9.Check for firmware and driver updates. See “Updating the firmware” on page 80.
10.Install other applications. Refer to the documentation that comes with the applications that you want to install.
© Copyright Lenovo 2011 |
5 |
6 ThinkServer Hardware Maintenance Manual
This chapter provides information about the server package, features, specifications, software programs, and component locations.
This chapter contains the following items:
•“Server package” on page 7
•“Features” on page 7
•“Specifications” on page 12
•“Software” on page 12
•“Locations” on page 13
The server package includes the server, power cord(s), printed documentation, documentation DVD, and software media.
Figure 1. Server package
1Server
2Material box, including power cord(s), printed documentation, documentation DVD, and software media
This topic provides general information about the server features for a variety of models. Depending on your specific model, some features might vary or not be available. For information about your specific model, use the Setup Utility program. See “Viewing information in the Setup Utility program” on page 55.
© Copyright Lenovo 2011 |
7 |
Microprocessor
Your server comes with one of the following microprocessors (internal cache size varies by model):
•Intel® Xeon® quad-core microprocessor
•Intel Xeon dual-core microprocessor
•Intel Core™ i3 microprocessor
For a list of the ThinkServer microprocessor options, go to http://www.lenovo.com/thinkserver. Click the
Products tab and then click Options ThinkServer Processors to view the information.
Memory
Your server supports up to four double data rate 3 unbuffered dual inline memory modules (DDR3 UDIMMs) with Error Checking and Correcting (ECC) technology.
•Supports 2 GB and 4 GB 1333 MHz DDR3 UDIMMs
•Single-rank or dual-rank
•Minimum system memory: 2 GB (only one 2 GB memory module installed in the DIMMA2 slot)
•Maximum system memory: 16 GB (one 4 GB memory module installed in each of the four memory slots)
For more information, see “System board components” on page 42 and “Memory module installation rules” on page 90.
Power supply
Your server comes with one of the following power supply configurations:
•One screw-secured, non-hot-swap 400-watt power supply (80 Plus Bronze Compliant and universal input)
•One or two hot-swap 450-watt redundant power supply modules (80 Plus Gold Compliant and universal input)
Fans
You server comes with the following fans to provide proper system cooling and airflow:
•One heat sink and fan assembly
•One or two front system fans depending on the model
•One rear system fan
8 ThinkServer Hardware Maintenance Manual
Internal drives
Internal drives are devices that your server uses to read and store data. The internal drives supported by your server vary by model.
•Hard disk drive
–Five to eight 3.5-inch hot-swap Serial Advanced Technology Attachment (SATA) or Serial Attached SCSI (SAS) hard disk drives (SCSI is the acronym for Small Computer System Interface)
–Up to eight 2.5-inch hot-swap SAS hard disk drives
–Up to four 3.5-inch hot-swap SATA or SAS hard disk drives
–Up to four 3.5-inch non-hot-swap SATA hard disk drives
Note: For server models with more than four hard disk drives or models that use SAS hard disk drives, there must be a required RAID card installed. See “RAID card” on page 33.
•Optical drive
–Up to two 5.25-inch SATA optical drives (DVD-ROM or DVD Burner / CD-RW Rambo 8)
–The lower optical drive bay is installed with a 5.25-inch SATA optical drive (DVD-ROM or DVD Burner / CD-RW Rambo 8). The upper optical drive bay is for a Removable Disk Technology (RDX) Universal Serial Bus (USB) drive bundle.
For the location information about the internal drives or drive bays, see “Server components” on page 25. For information about the RDX USB drive bundle and instructions on how to install it, refer to the documentation that comes with the RDX USB drive bundle. In your server, the P6 power connector of the power supply is for the RDX USB drive bundle. You can purchase this option directly from Lenovo. The
option name is Lenovo Removable Disk Technology (RDX) USB Drive Bundle. The RDX technology combines the characteristics of tape backup with disk storage to help you protect and archive data.
Expansion slots
The server has four expansion slots on the system board. For detailed information, see “System board components” on page 42.
Input/Output (I/O) features
•One Video Graphics Array (VGA) DB-15 connector on the rear panel
•Six USB 2.0 connectors (two on the front panel and four on the rear panel)
•Two RJ-45 Ethernet connectors on the rear panel
•Two serial connectors (one fully-functional serial connector on the rear panel and one internal serial connector on the system board for optional use)
For the location information about the connectors, refer to the related topic in “Locations” on page 13.
Video subsystem
An integrated graphics controller in the Baseboard Management Controller (BMC) chip on the system board to support a VGA DB-15 connector on the rear panel for connecting video devices
Ethernet connectivity
The server comes with an integrated Intel Gigabit Ethernet controller as well as an Ethernet physical layer (PHY) of the Open Systems Interconnection model (OSI model). They provide the server with the ability to support two Ethernet connectors on the rear panel with 10 Mbps, 100 Mbps, or 1000 Mbps network connectivity. For more information, see “Rear view of the server” on page 19.
Chapter 3. Product overview 9
Reliability, availability, and serviceability
Reliability, availability, and serviceability (hereinafter referred to as RAS) are three important server design features. The RAS features help you to ensure the integrity of the data stored on the server, the availability of the server when you need it, and the ease with which you can diagnose and correct problems.
Your server has the following RAS features:
•Security features
–Server locks (see “Server locks” on page 22)
–Administrator password and user password to help protect unauthorized access to the server (see “Using passwords” on page 65)
–Trusted Platform Module (TPM) connector on the system board for a TPM module, which is a security chip, to help protect your server and strengthen server security
Note: The TPM module is only available in some models.
–Remote monitoring or control by an administrator to provide protection or help
–Hot-swap redundant power supply modules to help you avoid significant interruption to the operation of the system when a power supply module fails (available in some models)
•Basic system management features
–Ability to store the power-on self-test (POST) hardware test results
–BIOS Setup Utility program
The BIOS Setup Utility program helps you view the server information and configure the server in the pre-operating system environment. See “Using the Setup Utility program” on page 55.
–BMC and Intelligent Platform Management Interface (IPMI) 2.0
The system board platform management subsystem is based on the integrated BMC features. The BMC is a management chip that is integrated on the system board of your server. With the BMC chip, no matter what condition the server operating system is in and no matter if the server is on or off, as long as the server is connected to network and an ac power source, the interaction with the BMC controlled servers can be achieved through system network. The user can obtain the server hardware health information and system event log (SEL), and is able to conduct the operations including turning on or off the server, restarting the server, locking the power switch on the front panel, and so on. This part of the server management is independent of the operating system and is called out-of-band management.
The system board platform management subsystem consists of the integrated BMC, communication buses, sensors, Basic Input Output System (BIOS), and server management firmware. It is responsible for error management and reporting, system power control, thermal monitoring, system fan control, and other management features. The BMC provides system management and monitoring features based on the IPMI 2.0 specification. IPMI helps lower the overall costs of server management. You can find more information about IPMI 2.0 from the Web site of Intel. The BMC also supports some non-IPMI features, such as the Dynamic Host Configuration Protocol (DHCP) and the Platform Environment Control Interface (PECI), to provide more system management functions.
Refer to the Remote Management Module User Guide on the documentation DVD that comes with your server for more information.
–Hot-swap feature
Some models support hot-swap hard disk drives and or hot-swap redundant power supply modules. With the hot-swap feature, you can install, remove, or replace hard disk drives or a failing power supply module without turning off the server.
10 ThinkServer Hardware Maintenance Manual
–Preboot Execution Environment (PXE)
The Intel PXE technology enables you to boot your computers, load an operating system, or deploy executable images from a remote server by using a network interface. The operation can be done independently of local data storage devices (such as hard disk drives) or installed operating systems.
–Redundant Array of Independent Disks (RAID)
Your server supports onboard SATA software RAID and advanced SATA/SAS hardware RAID configurations if you have a required RAID card installed. For detailed information, see “Configuring RAID” on page 71.
–Status light-emitting diodes (LEDs) and diagnostic LEDs
For more information about the LEDs for your server, refer to the related topics in “Locations” on page 13.
–ThinkServer EasyStartup program and ThinkServer EasyUpdate Firmware Updater program For more information about the software programs, see “Software” on page 12.
–Wake on LAN
When the Wake on LAN feature is enabled on a computer that is connected to a local area network (LAN), a network administrator can remotely turn on or wake up the computer from a management console using remote network management software. Besides, many other functions, such as data transfer and software updates, can be performed remotely without remote attendance and can be done after normal working hours and on weekends to save time and increase productivity.
•Advanced system management features
The BMC firmware supports the following advanced system management features:
Note: The advanced system management features are only available when the BMC detects the presence of an integrated keyboard, video, and mouse (iKVM) key. The iKVM key is a remote management module. You can purchase an iKVM key from Lenovo and install it on the iKVM key connector on the system board of your server to enable the iKVM function and activate the advanced system management features.
–iKVM redirection
The BMC firmware supports iKVM redirection over LAN. This feature is available remotely from the embedded Web server. The remote management module can digitize and compress the collected keyboard, video, and mouse signals from the host system and then send them to the remote console. Meanwhile, it is easily accessible by remote KVM and controllable through LAN or Internet. For detailed information, refer to the Remote Management Module User Guide on the documentation DVD that comes with your server.
–Media redirection
The embedded Web server provides a Java JNLP to enable the remote media redirection. This is used in conjunction with the remote KVM feature or as a standalone applet.
The media redirection feature is intended to enable system administrators or users to mount a remote optical drive, floppy drive, or USB flash disk as a USB device to the server. Once mounted, the remote device functions as a local device to the server, enabling system administrators or users to boot the server and install software (including operating systems), copy files, update the BIOS from this device.
–Web Services for Management (WS-MAN)
The BMC firmware supports the WS-MAN specification.
–Local Directory Authentication Protocol (LDAP)
The BMC firmware supports the LDAP for user authentication.
Note: The IPMI users, passwords, and sessions are not supported over LDAP.
Chapter 3. Product overview 11
–Embedded Web server
The BMC provides an embedded Web server for out-of-band management. The user authentication is handled by IPMI user names and passwords. For more information, refer to the Remote Management Module User Guide on the documentation DVD that comes with your server.
This topic lists the physical specifications for your server.
Dimensions
Width: 195 mm (7.68 inches)
Height: 430 mm (16.93 inches) without foot stands; 445 mm (17.52 inches) with foot stands Depth: 595 mm (23.43 inches) including the front bezel
Weight
The product weight varies depending on different system configurations.
Range of product weight without package: 19 kg (41.89 lb) to 28 kg (61.73 lb)
Range of product package weight: 2.8 kg (6.17 lb) to 3.5 kg (7.72 lb)
Environment
• Air temperature:
Operating: 10°C to 35°C (50°F to 95°F)
Storage: -40°C to 70°C (-40°F to 158°F) in original shipping package
•Altitude: 0 to 3 048 m (0 to 10 000 ft)
•Humidity:
Operating: 8% to 80% (non-condensing)
Storage: 8% to 90% (non-condensing)
Electrical input
Universal input:
Minimum: 90 V ac
Maximum: 264 V ac
Input frequency range: 47 to 63 Hz
This topic provides information about the software programs that you can use to help you set up, use, and maintain the server.
The ThinkServer EasyStartup program simplifies the process of configuring RAID and installing supported Microsoft® Windows® and Linux® operating systems and device drivers on your server. This program is provided with your server on a self-starting (bootable) ThinkServer EasyStartup DVD. The user guide for the program is also on the DVD and can be accessed directly from the program interface. For detailed information, see “Using the ThinkServer EasyStartup program” on page 69.
12 ThinkServer Hardware Maintenance Manual
The ThinkServer EasyUpdate Firmware Updater program (hereinafter referred to as the Firmware Updater program) enables you to maintain your server firmware up-to-date and helps you avoid unnecessary server outages. The Firmware Updater program is provided on the Lenovo Support Web site. For more information about downloading and using the Firmware Updater program, see “Updating the firmware” on page 80.
The BIOS and BMC firmware keeps updating after the shipment of the server. Lenovo maintains pages on the Support Web site and provides the BIOS and BMC firmware update utility with instructions for
download to help you update the BIOS and BMC firmware if needed. For more information, see “Updating or recovering the BIOS” on page 67 and or “Updating the firmware” on page 80.
Your server supports onboard SATA software RAID and advanced SATA/SAS hardware RAID configurations if you have a required RAID card installed. For detailed information, see “Configuring RAID” on page 71.
The PC-Doctor for DOS is a diagnostic tool that you can use to test and gather information about your system in order to ensure your system is working correctly and resolve any hardware issues. You can download the latest version of this diagnostic program from http://support.lenovo.com and create a self-starting DOS-based diagnostic utility that you can use to detect failing hardware components independently of the operating system. For more information, see “Using the diagnostic program” on page 172.
This topic provides information to help you locate your server components.
This topic helps you locate the two labels that contain the machine type, model, and serial number information for your server. The two labels are the same. One is on the front bezel and the other is on the chassis.
The machine type, model, and serial number identify your server. When you contact Lenovo for help, the information helps support technicians to identify your server and provide faster service.
Chapter 3. Product overview 13
The following illustration is a sample of the machine type, model, and serial number labels on the server.
Note: Depending on the model type, your server might look slightly different from the illustration in this topic.
Figure 2. Machine type, model, and serial number labels
14 ThinkServer Hardware Maintenance Manual
This topic provides information to help you locate the parts on the front of the server.
The following illustration shows the front view of the server.
2 1
CPU
MEM
PSU
Figure 3. Front view of the server
|
|
Front panel |
|
|
Front door |
|
1 |
|
6 |
||
|
|
|
|
|
|
|
|
Optical drive bay 2 (with an optical drive installed |
|
|
Front door lock |
|
2 |
|
7 |
||
|
in |
some models) |
|
|
|
|
|
|
|
|
|
|
|
Optical drive bay 1 (with an optical drive installed) |
|
|
Front door handle |
|
3 |
|
8 |
||
|
|
|
|
|
|
|
|
Optical drive eject/close button |
|
|
Doctor Inside Technology (DIT) panel (available in some |
|
4 |
|
9 |
||
|
|
|
|
models) |
|
|
|
|
|
|
|
|
|
Optical drive status LED |
|
|
|
|
5 |
|
|
|
|
|
|
|
|
|
|
1 |
Front panel |
For detailed information about the control, connectors, and status LEDs on the front panel, see “Front panel” on page 17.
2 |
Optical drive bay 2 |
The 5.25-inch optical drive bay 2 is for a secondary optical drive or a RDX USB drive bundle (server option). Some models have a secondary optical drive installed.
Chapter 3. Product overview 15
3 |
Optical drive bay 1 |
Your server comes with an optical drive installed in the 5.25-inch optical drive bay 1.
4 |
Optical drive eject/close button |
Press this button to eject or close the optical drive when the server power is on.
5 |
Optical drive status LED |
The optical drive status LED is blinking in green when the optical drive is working or in the POST process.
6 |
Front door |
7 |
Front door lock |
You can lock the front door to protect the hard disk drive cages from unauthorized access.
8 |
Front door handle |
The front door handle helps you to open the front door.
9 |
DIT panel |
The DIT panel is only available in models that come with a DIT module. For more information, see “DIT module” on page 18.
16 ThinkServer Hardware Maintenance Manual
This topic provides information to help you locate the control, connectors, and LEDs on the front panel of the server.
The following illustration shows the control, connectors, and LEDs on the front panel of the server. Depending on the model, your server might look slightly different from the following illustration.
Figure 4. Front panel
|
|
Power switch with power status LED |
|
|
System status LED |
|
1 |
|
5 |
||
|
|
|
|
|
|
|
|
Hard disk drive status LED |
|
|
Front USB connector 1 |
|
2 |
|
6 |
||
|
|
|
|
|
|
|
|
Network Interface Controller (NIC) 1 status LED |
|
|
Front USB connector 2 |
|
3 |
|
7 |
||
|
|
|
|
|
|
|
|
NIC 2 status LED |
|
|
|
|
4 |
|
|
|
|
|
|
|
|
|
|
1 |
Power switch with power status LED |
You can press the power switch to turn on the server when you finish setting up the server. You can also hold the power switch for several seconds to turn off the server if you cannot turn off the server from the operating system. See Chapter 4 “Turning on and turning off the server” on page 53. The power status LED helps you to determine the current power status.
Chapter 3. Product overview 17
Power status LED |
Color |
Description |
|
|
|
On |
Green |
The server is on. |
|
|
|
Off |
None |
The server is off. |
|
|
|
Blinking |
Green |
The server is in ACPI S1 mode, which is also known |
|
|
as Power On Suspend (POS) mode. In this mode, the |
|
|
microprocessor is not working while other hardware |
|
|
devices are still working. |
|
|
|
2 |
Hard disk drive status LED |
The hard disk drive status LED helps you to determine the status of the hard disk drive activity.
Hard disk drive status LED |
Color |
Description |
|
|
|
Off |
None |
The hard disk drive is not in use. |
|
|
|
Blinking |
Green |
The hard disk drive is active and data is being |
|
|
transferred. |
|
|
|
3 |
NIC 1 status LED |
4 |
NIC 2 status LED |
The two NIC status LEDs indicate the LAN status for the Ethernet connector 1 and Ethernet connector 2 on the rear panel of the server.
NIC status LED |
Color |
Description |
|
|
|
On |
Green |
The server is connected to a LAN. |
|
|
|
Off |
None |
The server is disconnected from a LAN. |
|
|
|
Blinking |
Green |
The LAN is connected and active. |
|
|
|
5 |
System status LED |
The system status LED helps you to determine if there are any system errors.
System status LED |
Color |
Description |
|
|
|
On |
Amber |
A system error has occurred. |
|
|
|
Off |
None |
The server is off or the server is on and is working |
|
|
correctly. |
|
|
|
6 |
Front USB connector 1 |
7 |
Front USB connector 2 |
Used to attach a device that requires a USB connector, such as a USB keyboard, a USB mouse, a USB scanner, or a USB printer. If you have more than six USB devices, you can purchase a USB hub, which you can use to connect additional USB devices.
This topic provides information about the DIT module and the diagnostic LEDs on the panel of the DIT module.
18 ThinkServer Hardware Maintenance Manual