WS-9117U
Wireless 433 MHz
Temperature Station
Instruction Manual
1
TABLE OF CONTENTS
Topic |
Page |
Inventory of Contents |
3 |
Quick Setup |
4-8 |
Detailed Setup Guide |
|
Battery Installation |
9-11 |
Setting the Time |
11-12 |
Selecting Units of |
12-13 |
Measurement |
|
Features |
|
Minimum and Maximum |
13 |
Temperatures |
|
Resetting Minimum and |
13-14 |
Maximum Temperatures |
|
Additional remote |
14-16 |
temperature sensors |
|
(optional) |
|
Mounting |
17-18 |
Troubleshooting |
19-20 |
Maintenance and Care |
21 |
Specifications |
22-23 |
Warranty Information |
24-28 |
2
INVENTORY OF CONTENTS
1.The indoor temperature station (Figure 1)
2.The remote temperature sensor (TX6U) and mounting bracket. (Figure 2)
3.3 each, 1/2” Philips screws.
4.One strip of double sided adhesive tape.
5.Instruction Manual and Warranty Card.
Figure 1 |
Figure 2 |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ADDITIONAL EQUIPMENT
(not included)
1.1 Philips screwdriver.
2.2 Fresh AAA 1.5V batteries.
3.2 Fresh AA 1.5V batteries.
3
QUICK SETUP
Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries.
1.Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart.
2.Batteries should be out of both units for 10 minutes.
3.Place the batteries into the remote temperature
sensor first then into the indoor temperature station.
(All remote temperature sensors must be started before the indoor temperature station)
4.DO NOT PRESS ANY BUTTONS FOR 15 MINUTES.
4
In this time the indoor temperature station and remote temperature sensor will start to talk to each other and the display will show both the indoor temperature and an outdoor temperature. If the indoor temperature station does not display both temperatures after the 10 minutes please retry the set up as stated above. After both indoor and outdoor temperatures are displayed for 15 minutes you can place your remote temperature sensor outdoors and set your time.
The remote temperature sensor should be placed in a dry, shaded area. The remote temperature sensor has a range of 80 feet. Any walls that the signal will have to pass through will reduce distance. An outdoor wall or window will have up to 20 feet of resistance and an interior wall will have up to 10 feet
5
of resistance. Your distance plus resistance should not exceed 80 ft. in a straight line.
NOTE: Fog and mist will not harm your remote temperature sensor but direct rain must be avoided.
To complete the set up of your indoor temperature station after the 15 minutes have passed please follow the steps below.
1.Press and hold the “SET/CH” button for 5 seconds.
Note: A “12h” or “24h” will appear to the left of the time. (“12h” for AM/PM, “24h” for military time)
a.To change between “12h” and “24h” press and release the “MIN/MAX” button.
6
b.When you have your choice shown on the display press and release the “SET/CH” button once.
2.Degree Fahrenheit will now show.
a.To change between Fahrenheit and Celsius, press and release the
“MIN/MAX” button.
b.When you have your choice shown on the display press and release the “SET/CH” button once.
3.An hour will now be flashing.
a.Press and release the “MIN/MAX” button until the correct hour is shown.
Note: When in the 12h mode there is “PM” displayed under
7
the word TIME when in the PM hours. During the AM hours this area will be blank.
b.When the correct hour is shown, press and release the “SET/CH” button once.
4.A minute will now be flashing.
a.Press and release the “MIN/MAX” button until the correct minutes are displayed.
Press and release the “SET/CH” button once more and you are done.
8
DETAILED SETUP GUIDE
I.BATTERY INSTALLATION
A. REMOTE TEMPERATURE SENSOR
1.Remove the mounting bracket.
2.Remove battery cover
3.Observing the correct polarity, install 2 AA batteries—make sure they do not spring free, or start-up problems may occur. Replace cover.
9
Loading...