Keurig B60 User Manual

WARNING

WARNING: TO REDUCE THE RISK OF FIRE

OR ELECTRIC SHOCK, DO NOT REMOVE

THE BOTTOM COVER. NO USER

SERVICEABLE PARTS ARE INSIDE. REPAIR

SHOULD BE DONE BY AUTHORIZED

SERVICE PERSONNEL ONLY.

RISK OF FIRE OR ELECTRIC SHOCK

DO NOT OPEN

3

KEURIG®GOURMET SINGLE CUP
HOME BREWING SYSTEM

Special Edition - Model B60
Use & Care Guide

TABLE OF CONTENTS

SECTION 1

SET-UP & OPERATION

Helpful Hints . . . . . . . . . . . . . . . . . . . . . . . . 4
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Set-Up & First Brew . . . . . . . . . . . . . . . . . . 6

SECTION 2

CONTROLS & INDICATORS

LCD Control Center . . . . . . . . . . . . . . . . . . . 9

SECTION 3

CLEANING & MAINTENANCE

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
De-Scaling . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

SECTION 4

TROUBLESHOOTING . . . . . . . . . . . . . . . . . 15

SECTION 5

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Pour des directives en Français,
veuillez vous reporter à la page 17.

CAUTION: There are two sharp needles that
puncture the K-Cup

®

portion pack, one
above the K-Cup Holder and the other in the
bottom of the K-Cup Holder.

T

o avoid risk of injury, do not put your

fingers in the K-Cup Chamber.

CAUTION: There is extremely hot water in
the K-Cup Holder during the brew process.

T

o avoid risk of injury, do not lift the Handle
or open the K-Cup Chamber during the
brew process.

SHORT CORD INSTRUCTIONS: A short power
supply cord is provided to reduce the risk of
becoming entangled in or tripping over a longer
cord.

If an extension cord is used, (1) the marked
electrical rating of the cord set or extension cord
should be at least as great as the electrical rating of
the appliance, (2) the cord should be arranged so
that it will not drape over the countertop or table­top where it can be pulled on by children or tripped
over unintentionally and (3) the extension cord
must include a 3-prong grounding plug.

THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.

Record your Brewer Serial Number here.
The Serial Number is located on the
bottom of the Brewer on a white sticker.

_________________________________

5

Features

Water Reservoir Lid

Water Reservoir

Water Reservoir Lock Tab Slots

Handle

K-Cup

®

Portion Pack Holder (E and F are

the K-Cup Holder Assembly)

Funnel

Lid

K-Cup

®

Portion Pack Assembly Housing

Housing

Drip Tray Plate

Drip Tray

Drip Tray Base

Vent

Power Cord

A

B

C

D

E

F

G

Cup/Hour/Minus Button

Mug Button

Travel Mug/Minute/Plus Button

Menu Button

LCD Control Center

Power Button

O

P

Q

R

S

O

P

Q

R

S

H

Special Edition - Model B60 Brewer

I

J

K

L

M

N

4

1. Keep your Brewer turned ‘ON’
at all times.

To brew a fresh cup of coffee or tea anytime
you want, we suggest you keep your Brewer
turned ‘ON’ all the time.

However, the Brewer is fully programmable so
you can set it to turn on and off automatically
to match your schedule. Or, if you prefer, set
the Brewer to automatically turn off after a
period of time.

Follow the simple instructions on page 9
to make using the Brewer convenient for you.

2. For the best tasting gourmet coffee or tea,
Keurig recommends using bottled or filtered
water.

Water quality varies from place to place. If you
notice an undesirable taste in your cup of coffee
such as chlorine or other mineral taste, we
recommend you consider using bottled water or
water from a filtration system.

3. Choose from three serving sizes.

The perfect cup of coffee means something
different to each coffee lover. With its wide vari­ety of coffees to choose from and the ability to
brew a stronger small cup (5.25 oz serving), a
regular mug (7.25 oz serving) or a travel mug
(9.25 oz serving), the Brewer lets you enjoy
your own personal cup brewed to perfection.
Follow the simple instructions on page 7.

4. Plug Brewer into its own grounded outlet.

If the electric circuit is overloaded with
other appliances, your Brewer may not
function properly. The Brewer should be
operated on its own circuit, separate from
other appliances.

5. Brewing into a travel mug.

To brew into a travel mug, simply remove the
Drip Tray Assembly and place the travel mug
on the Drip Tray Base.

1. Place Brewer box on a large steady surface
(such as a table or countertop) or
on the floor. Open the box.

2. Remove the Quick Start Guide, Use & Care
Guide and other literature.

3. Remove the package of complimentary
K-Cup

®

portion packs.

4. Turn the box on its side with front of box
face down.

5. Reach into the box and grasp the plastic
bag that contains the Brewer.

6. Carefully pull the plastic bag (and
packaging materials) toward you and out
of the box. The Brewer will still be encased
in the polyfoam and be on its side.

7. Remove the top polyfoam packaging
material.

8. Carefully lift Brewer off of the bottom
polyfoam and place it upright on a flat,
steady surface.

9. Lift plastic bag off of Brewer.

10. Carefully turn the Brewer on its side and
record on page 3 of this book the Serial
Number located on the white sticker on the
bottom of the Brewer. The Serial Number
is also located on the bottom of the Brewer
box.

11. Place the Brewer upright on a flat,
steady surface. Remove tape holding
Water Reservoir in place.

We recommend you save all packing materials
in case future shipping of the product
is necessary.

SET-UP & OPERATION

Helpful Hints

SECTION 1

WARNING: Keep all plastic bags away

from children.

Unpacking Instructions

Set-Up & First Brew

IMPORTANT: You cannot use your Keurig

brewer until it has been primed for its first use
as set forth below.

Priming your Brewer

1. Unwrap cord and plug the brewer into a
grounded outlet.

2. Place a cup or mug on the Drip Tray Plate.

3. Remove the Water Reservoir from Brewer by
first removing Lid from Reservoir, then lifting
Reservoir straight up and away from Brewer
(may be tight). Rinse with fresh water.

4. Fill Water Reservoir with fresh water so that
the water level is just below the top edge of
the reservoir.

5. Place Water Reservoir base into the left
side of the Brewer and be sure the
Water Reservoir Lock Tabs engage
with the Brewer. Replace Lid on Water
Reservoir.

6. Press the Power Button found directly
above the LCD Control Center. The blue light
surrounding the Travel Mug Button will
become illuminated and flash.

7. The LCD Control Center will come on and
indicate 'PRIME' and the button for the

Travel Mug will also flash. Please note, a K­Cup should not be used for the Priming
Sequence.

8. Press the Travel Mug Button.

9. The Brewer will automatically fill with water
(priming it) and then the water will be
heated. This will take about 3 minutes. During
the heating period 'NOT READY' is dis­played on the LCD Control Center. Once the
water is heated, 'READY' will be displayed and
the Travel Mug button will flash.

10.Press the Travel Mug Button to start a
cleansing brew, during which hot water will
flow into your cup or mug. Pour the hot
water into the sink.

11.The one-time priming process is now
complete and you are ready to brew!

6

7

Ready to Brew your First Cup

1. LCD Control Center will indicate 'READY TO
BREW'.

2. Place a cup or mug on the Drip Tray Plate.

3. Lift the Handle and the K-Cup Holder will
open toward you.

4. Select a K-Cup

®

portion pack.

5. Place a K-Cup

®

portion pack in the K-Cup

Holder (as shown in exhibit at top of page).

6. Lower the Handle to close the Lid over the
K-Cup Holder. (When it is closed completely,
the LCD Control Center will indicate ‘READY
TO BREW’ and the Cup, Mug and Travel Mug
Buttons will blink up to 60 seconds.)

7. Choose the amount of coffee or tea you
wish to brew by pressing the button that
indicates your choice. The Travel Mug choice

will yield a 9.25 oz serving, the Mug choice
will yield a 7.25 oz serving and the Cup
choice will yield a 5.25 oz serving.

8. The LCD Control Center will now display the
word ‘BREWING’ and the serving size you
selected will be solid blue.

9. There may be a short pause before the
brewing process begins. The process lasts
for approximately 40 seconds and ends
with a burst of air to remove all liquid
coffee or tea from the K-Cup.

10. Lift the Handle and remove and dispose of

the used K-Cup.

CAUTION: K-Cup will be hot.

11. Enjoy your first cup of Keurig Brewed

®

gourmet coffee or tea!

12. Your Brewer may display ‘NOT READY’ as

it heats water for the next brew cycle. The
‘READY TO BREW’ indication will return to
the LCD Control Center in about 15 seconds.

NOTE: You may see small amounts of water
coming from the Vent and dripping into the
Water Reservoir during this and subsequent
heating – this is normal.

NOTE: Do not remove the foil lid or
puncture the K-Cup

®

portion pack.

NOTE: If the Water Reservoir is empty or
not in place on the Brewer, then the LCD
Control Center will also indicate ‘ADD
WATER’. None of the buttons will be activated
until water is added to the Water Reservoir.

CAUTION: There are two sharp needles that
puncture the K-Cup

®

portion pack, one above
the K-Cup Holder and the other in the bottom
of the K-Cup Holder. T

o avoid risk of injury,

do not put your fingers in the K-Cup Chamber.

NOTE: If you do not push the Brew Buttons
in 60 seconds, the LCD Control Center will
return to 'READY TO BREW' and the Brew
Buttons will be disabled to prevent accidental
activation. Re-activate the Brew Buttons by
raising and lowering the Handle completely.

CAUTION: There is extremely hot water in
the K-Cup Holder during the brew process.

T

o avoid risk of injury, do not lift the
Handle or open the K-Cup Chamber
during the brew process.

Stopping the Brew Process

If you need to stop the brewing after the
process has started, press the Power Button to
turn the Brewer ‘OFF’. The flow of coffee
or tea will stop, the heating element will shut
off and the blue lights illuminating the brew
buttons and Water Reservoir will disappear.

Adding Water

The LCD Control Center of your Brewer will
indicate when the water level in the tank is low
or if the Water Reservoir has been removed by
displaying the words ‘ADD WATER’. The
Brewer will not allow you to brew when ‘ADD
WATER’ is displayed.

The Water Reservoir can be filled in two ways.

1. Lift off the Water Reservoir Lid and pour
water directly into the Water Reservoir
while it is still attached to the Brewer, then
replace the Lid.

2. Remove the Water Reservoir from Brewer

by first removing Lid from the Water
Reservoir, then lifting the Water Reservoir
straight up and away from Brewer. Fill with
water. Place the Water Reservoir back on
the Brewer and replace the Lid.

Brewing Hot Water

Your Brewer is able to produce a cup of hot
water for making hot chocolate, for use in
cooking, for making soups, etc. Simply raise
and lower the handle on the Brewer without
adding a K-Cup

®

portion pack. The LCD Control
Center will display 'READY TO BREW' and the
Cup, Mug and Travel Mug Buttons will blink. Be
sure to have a mug or cup on the Drip Tray and
then select the size you would like.

Purging the Brewer

If your Brewer has not been used for more
than one week, you should purge the water
from the inner tank.

1. If there is water in the Water Reservoir,

remove the Lid, then lift the Water Reservoir
straight up and away from Brewer. Discard
water, rinse and refill with water. Place the
Water Reservoir back on the Brewer and
replace the Lid. (If there is no water in the
Water Reservoir, simply refill.)

2. Be sure the Brewer is turned on. Raise and

lower the handle on the Brewer without
inserting a K-Cup

®

portion pack.

3. The LCD Control Center will display 'READY

TO BREW' and the Cup, Mug and Travel
Mug Buttons will blink. Be sure to have a
travel mug on the Drip Tray and then select
the Travel Mug size brew.

4. Repeat steps 2 and 3 one more time to

completely purge water from inner tank.

If you are experiencing any problems with
your Brewer, please contact Customer
Service at 1-866-901-BREW (2739).

8

9

SECTION 2

LCD Control Center

Setting the Clock

Setting the clock is optional. When the clock
is set, the time will appear in the LCD Control
Center. NOTE: You must set the clock if you
will be using the Auto On/Off Time program­ming feature.

a. Press the button below 'MENU'.
b. The word 'OFF' will appear at the bottom

of the LCD Control Center to indicate that
the clock is not set. The programming
options will appear on the LCD Control
Center with a small arrow pointing to 'SET
CLOCK'. H (Hour) and M (Minute) will
appear and blink.

c. Press or hold the blue Cup button under

the blinking H until you have reached the
appropriate hour. If the hour has passed
12, the indicator switches from AM to PM.

d. Press or hold the blue Travel Mug button

under the blinking M to set the minutes.

e. When you have reached the correct time,

press the menu button five times to scroll
through the remaining programming
options and exit the programming mode.

f. The correct time should now be displayed

in the LCD Control Center.

Programing On/Off Features

The Brewer provides three modes so that you
can enjoy gourmet coffee or tea on your own
schedule. By programming your Brewer to
turn on each morning, you will never have to
wait for the Brewer to warm up to brew a
gourmet cup of coffee.

1. Leave it ON all the time (recommended).

The Brewer can be left on all the time so
that it is always ready to brew a fresh cup
of gourmet coffee or tea. To turn the
Brewer off at any time, simply press the
Power Button. (Note: Although the clock
remains on if set, you can not brew a cup
of coffee or tea.) Press the Power Button
again to restore power to the Brewer. You
will have to wait for the water to heat up
before the Brewer is ready to brew.

2. Set the Brewer to turn off at a specified
period of time after the last brew.

a. Press the MENU button twice to pro-

gram the AUTO OFF feature. The LCD
Control Center will now display the pro­gramming options with a small arrow
next to 'SET AUTO OFF'.

b.Press or hold the blue CUP button under

the blinking H to advance 1 hour at a
time, up to 9 hours.

CONTROLS & INDICATORS

NOTE: You may get less coffee or tea in

your cup during your next brew. We
recommend that you perform a cleansing
brew with water only after a terminated brew.
Then your NEXT brew will be the volume
you have selected.

IMPORTANT: Do not remove the Water
Reservoir during the brewing process.

NOTE: If power is interrupted to the
Brewer by unplugging it, or if power is
lost, follow the procedure above to reset
the time as the clock will not be visible
until the time is set.

NOT READY

ADD

WATER

READY

NOT

SET CLOCK

AUTO OFF
ON OFF TIME
BREW TEMP

MENU

M

H

OFF

READY

NOT

CLOCK

SET AUTO OFF

ON OFF TIME
BREW TEMP

H

MENU

10

11

c. After setting the desired AUTO-OFF time,

press the MENU button four times to
scroll through the remaining program­ming options and exit the programming
mode. 'AUTO OFF SET' will now be dis­played to indicate that it has been set.

d.To cancel the AUTO-OFF feature, press

the MENU button twice to reach the
AUTO-OFF programming mode. Press
and release the blue Cup button under
the blinking H to advance one hour at a
time until ‘OFF’ is displayed.

3. Program your Brewer for a specific Auto
On/Off Time.

a. After setting the correct time (required),

press the Menu Button three times to
program the Auto On time feature. The
LCD Control Center will show the pro­gramming options with a small arrow
next to 'SET ON TIME'.

b.Press or hold the blue Cup button under

the H to scroll through the hours to your
desired ON time hour.

c. Press or hold the blue Travel Mug

button under the M to scroll through the
minutes to your desired ON time
minutes.

d. After setting the desired time, press the

Menu Button to save the On Time and
move to the SET OFF TIME.

e. If you want to set an OFF time, repeat

the procedure above in steps b & c to
set your desired OFF time.

f. To complete the process, press the

Menu Button two more times to exit the
programming mode. The Control Center
will now indicate the options you have set.

g. The AUTO ON time and AUTO OFF time

functions operate independently from
one another. To cancel either set func­tion, follow the steps above and use the
H and M buttons to advance to 12:00
AM. When you reach 12:00 AM, the
Control Center will display ‘OFF’ and the
function will be disabled.

EXAMPLE: If you chose to set the On Time at
6:15 AM and the Off Time for 10:00 PM, then
the Brewer will be ‘ON’ and maintain hot
water in the tank during that time so that it is
always ready for you to brew. If you wanted
to brew outside this window, simply press the
Power Button and you can brew as soon as
the water is heated and the ‘READY TO
BREW’ indicator is displayed on the LCD
Control Center.

Programming Brew Temperature
(187° - 192º F)

The Brewer brews coffee at a preset tempera­ture of 192 degrees. You can adjust this tem­perature down by 5 degrees if you prefer a
cooler cup of coffee or tea. Simply follow the
instructions below.

1. Press the Menu Button on the LCD Control
Center five times to program the Brew
Temperature feature.

2. The LCD Control Center will now display
the programming options with a small
arrow next to ‘SET BREW TEMP’. Also, the
temperature 192 (initial setting) will be dis­played at the bottom of the LCD Control
Center to indicate the current temperature
setting.

3. A minus sign will appear over the Cup
button and/or a plus sign over the Travel
Mug button. Use these buttons to raise or
lower the temperature one degree at a
time.

4. Once you have reached your desired brew
temperature, press the MENU button once
to exit the programming mode. ‘BREW
TEMP SET’ will be displayed in the LCD
Control Center if you have changed it from
192°.

5. To change the brew temperature again,
repeat steps 1 through 3 to change the
temperature up and/or down, remembering
that the temperature can only be between
187 degrees and 192 degrees.

NOTE: To use this programming feature,
the clock must be set to the correct time.
The clock will not be displayed unless the
time is set.

NOTE: The AUTO OFF Timer and the AUTO
ON/OFF Time programming options operate
independently, but can also be programmed
to work together. For example, you can set
the AUTO ON Time function to turn on at
7:00 AM and then set the AUTO OFF Timer
function to turn off the Brewer two hours
after the last brew.

READY

BREW

AUTO OFF SET
ON TIME SET

MENU

AM

TO

READY

BREW

TO

AUTO OFF SET

AM

MENU

READY

NOT

CLOCK
AUTO OFF

SET ON

TIME

BREW TEMP

AM

MENU

M

H

READY

NOT

CLOCK
AUTO OFF

SET

OFF TIME

BREW TEMP

H

OFF

MENU

M

READY

NOT

CLOCK
AUTO OFF
ON OFFTIME

TEMP

SET

BREW

º

192

MENU