Kenwood XD-855E, XD855, XD-755E, XD655, XD755 User Manual

0 (0)

COMPACT HI-FI SYSTEM

XD-SERIES

XD-855 / XD-855E / XD855

XD-755 / XD-755E / XD755

XD-655 / XD655

INSTRUCTION MANUAL

KENWOOD CORPORATION

This instruction manual is for some models.Model availability and features

(functions) may differ depending on the country and sales area.

B60-5014-00 00 MA (E2, T, M, M3, M5, X) KW 0010 TINSE0371AWZZ

BEFORE APPLYING POWER

Caution : Read this page carefully to ensure safe operation.

Units are designed for operation as follows.

Europe and U.K. ...........................

AC 230 V only

Other countries ..........

AC 110 / 127 / 220 / 230 -

China and Russia ..........................

AC 220 V only

 

240 V switchable*

For the United Kingdom

 

 

 

Factory fitted moulded mains plug

1.The mains plug contains a fuse. For replacement, use only a 3-Amp ASTA-approved (BS1362) fuse.

2.The fuse cover must be refitted when replacing the fuse in the moulded plug.

3.Do not cut off the mains plug from this equipment.

If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety ap-

proved extension lead or adapter, or consult your dealer.

If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.

IMPORTANT:The wires in the mains lead are coloured in accordance with the following code:

Blue : Neutral

Brown : Live

Do not connect those leads to the earth terminal of a three-pin plug.

* AC voltage selection

The AC voltage selector switches on the rear panel are set to the voltage that prevails in the area to which the unit is shipped. Before connecting the power cord to your AC outlet, make sure that the setting positions of these switches match your line voltage. If not, they must be set to your voltage in accordance with the following direction.

AC voltage selector switches

Turn the selector to match your line voltage with a small screwdriver or other pointed tool.

(110V, 127V, 220V or 230V - 240V AC)

230V I 240V

Note: Our warranty does not cover damage caused by excessive line voltage due to improper setting of the AC voltage selector switch.

SAFETY PRECAUTIONS

WARNING :TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.

THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.

The marking of products using lasers (Except for some areas)

CLASS 1

LASER PRODUCT

The marking is located on the rear panel and says this product has been classified as Class

1. It means that there is no danger of hazardous radiation outside the product

2 EN

CONTENTS

 

Page

BEFORE APPLYING POWER...............................

2

SAFETY PRECAUTIONS ......................................

2

ACCESSORIES ....................................................

3

HANDLING OF DISCS AND TAPES .....................

4

NAMES OF CONTROLS AND INDICATORS

 

.......................................................................

5 - 7

PREPARATION FOR USE ..............................

8 - 10

SETTING THE CLOCK ..................................

11 -12

SETTING THE CHANNEL SPAN (Except for the

Europe and U.K.) ...............................................

12

SOUND CONTROL ...........................................

13

COMPACT DISC OPERATION .....................

14 - 18

 

Page

RADIO OPERATION ...................................

19 - 21

RDS (RADIO DATA SYSTEM) OPERATION

 

(For UK and Europe only) ...........................

22 - 29

CASSETTE OPERATION ....................................

30

RECORDING (TAPE B only) ........................

31 - 32

HOW TO USE THE BUILT-IN TIMER ............

33 - 35

USING EXTERNAL UNITS .................................

36

RESETTING THE MICROCOMPUTER ...............

37

TRANSPORTING THE UNIT...............................

37

MAINTENANCE ................................................

38

SPECIFICATIONS .......................................

39 - 40

ACCESSORIES

FM Antenna

AM Loop Antenna

Remote Control

“AA” size battery (UM/

(1)

(1)

(1)

SUM-3, R6, HP-7 or similar)

 

 

 

(2)

AC Plug Adaptor (1)

Use to adapt the plug on the power cord to the shape of the wall outlet.

(Accessory only for regions where use is necessary.)

3 EN

HANDLING OF DISCS AND TAPES

Disc handling precautions

Handling

 

Hold the discs so that you do not

 

touch the playing surface.

 

Label side

 

Playing side

Sticker

Do not attach paper or tape to ei-

 

ther the playing side or the label

 

side of the discs.

Sticky paste

Cleaning

If fingerprints or foreign matter

become attached to the disc,

lightly wipe the disc with a soft

cotton cloth (or similar) from the center of the disc outwards in a radial manner.

Storage

When a disc is not to be played for a long period of time, remove it from the player and store it in its case.

Discs which can be played with this unit

CD (12 cm, 8 cm) and the audio part of CDV, CD-G, CD-EG and CD-EXTRA. Use discs that comply with the IEC standard, for example a disc carrying the

marking on the label surface.

Never play a cracked or warped disc

During playback, the disc rotates at high speed in the player. Therefore, to avoid danger, never use a cracked or deformed disc or a disc repaired with tape or adhesive agent. Please do not use discs which are not round because they may cause a malfunction.

Disc accessories

The disc accessories (stabilizer, protection sheet, protection ring, etc.) which are marketed for improving the sound quality or protecting discs as well as the disc cleaner should not be used with this system because they may cause malfunction.

Notes on cassette tape

Safety tab (accidental erasure prevention tab)

After an important recording has been finished, break the safety tab, to prevent the recorded contents from being erased or recorded on accidentally.

To store cassette tapes

Do not store the tapes in a place which is subject to direct sunlight, or near equipment that generates heat. Keep the cassette tapes away from any magnetic field.

When there is slack in the tape

In such a case, insert a pencil into the reel hole

For A side and wind the reel hub to remove the slack. For B side

To re-record

Apply tape only to the position where the tab has been removed.

Note :

Do not use an endless tape, as this could damage the mechanism of the unit.

Do not use a cassette with more than 90 minutes recording time, for the tape used in such a cassette is very thin and tends to cause troubles such as engantlement around the pinch roller or cutting of tape.

4 EN

NAMES OF CONTROLS AND INDICATORS

FRONT PANEL

1 EX.BASS / DEMO button

% Display

2 STANDBY / TIMER indicator

^ Disc tray

3 REVERSE MODE button

& DISC SKIP button

4

 

 

ON / STANDBY button

* 0OPEN / CLOSE button

 

 

 

 

 

5 VIDEO / AUX button

( SOUND MODE button

6 TAPE (A/B) button

) CLOCK button

7 TUNER (BAND) button

¡ TIMER button

8 CD button

™ MEMORY / SET button

9 2(Reverse play) button

£ P. CALL (4 1 ¡ ¢) buttons

0 7STOP button

¢ VOLUME CONTROL knob

! 3(Play / repeat) button

° TUNING / TIME (%UP fiDOWN) buttons

@ PHONES socket

§ REC PAUSE button

# PUSH OPEN (Tape A)

¶ PUSH OPEN (Tape B)

$ (TAPE A) cassette compartment

• (TAPE B) cassette compartment

Standby mode

While the standby indicator of the unit is lit, a small amount of current is flowing into the unit’s internal circuitry to back up the memory. This condition is referred to as the standby mode of the unit. While the unit is in the standby mode, it can be turned ON from the remote control unit.

5 EN

Kenwood XD-855E, XD855, XD-755E, XD655, XD755 User Manual

DISPLAY

 

 

 

34567 890

!

@

#

 

 

 

$

2

 

 

%

 

 

 

^

 

 

 

&

 

 

 

*

1

 

 

(

 

 

 

)

 

 

 

¡

 

 

For UK and Europe only

1 Timer Related Indicator

@ Record Indicator

2 Disc Number Indicator

# Extra Bass Indicator

3 Repeat Indicator

$ Forward / Reverse Play Indicator

4 FM Stereo Mode Indicator

% Reverse Mode Indicator

5 Play Indicator

^ Programme Type Indicator

6 Programme Indicator

& RDS Indicator

7 Pause Indicator

* Radio Text Indicator

8 Random Play Indicator

( Traffic Programme Indicator

9 Tuned Indicator

) Traffic Information Indicator

0 Equalizer Indicator

¡ Traffic Announcement Indicator

! Spectrum Analyzer / Volume level Indicator

 

REAR PANEL

1 AC voltage selector switches (Except for the Europe and U.K.)

2 AC Power Cord

3 FM 75 Ω Antenna Socket

4 AM Loop Antenna Socket

5 Span Selector (Except for the Europe and U.K.)

6 Video / Auxiliary (Audio Signal) Input sockets

7 Speaker Terminals

3

14

5 6

27

6 EN

REMOTE CONTROL

For UK and Europe only

1 MEMORY / SET button

2 CLEAR button

3 CLOCK button

4 TIMER button

5 Disc Number Select buttons

6 TUNING / TIME (% fi) buttons

7 7 (Stop) button

8 2 (Reverse Play) button

9 CD button

0 TUNER (BAND) button ! POWER button @ AUTO MEMORY button

# RDS DISPLAY button $ PTY button

% REVERSE MODE button

^ RANDOM button

& EX.BASS button

* SOUND MODE button

( DISC SKIP button

) P. CALL (4 1 ¡ ¢) buttons

¡ 8 (Pause) button

™ 3 (Play / Repeat) button

£ VIDEO / AUX button

¢ TAPE (A/B) button

° VOLUME buttons

Notes :

Remote control RC-655E is for UK and Europe only.

Remote control RC-655 is for other countries.

7 EN

PREPARATION FOR USE

Unplug the AC power cord from the AC socket before connecting or disconnecting any component.

Right speaker

Left speaker

Red

Red

Black

Black

Speaker connection

Connect each speaker wire to the SPEAKERS terminals as shown. Use speakers with an impedance of 6 Ω or more, as lower impedance speakers can damage the unit.

Connect the black wire to the minus (-) terminal, and the red wire to the plus (+) terminal.

Caution :

Do not mix the right channel and left channel wiring when connecting the speakers to the unit. The right speaker is the one on the right side when you are facing the front of the unit.

Do not let bare speaker wires touch each other as this may damage the amplifier and/or speakers.

Do not allow any objects to fall into or to be placed in the bass reflex ducts.

Do not stand or sit on the speakers. If the speakers fall or collapse, you may be injured.

System Name

Speaker Model

Name

 

 

XD-855

/ XD-855E / XD855

LS-N90S

 

 

 

XD-755

/ XD-755E / XD755

LS-N70S

 

 

 

XD-655

/ XD655

LS-N50S

 

 

 

CAUTION

Be sure to adhere the followings, or proper ventilation will be blocked causing damage or fire hazard.

÷Do not place any objects impairing heat radiation onto the top of unit.

÷Leave space around the unit (from the largest outside dimension including projection) equal to or greater than, shown below.

Top panel : 50 cm

Side panel : 10 cm

Back panel : 10 cm

8 EN

FM antenna

AM loop

antenna

 

External FM antenna

Antenna connection

Supplied FM antenna

Connect the FM antenna wire to the FM 75 Ω terminal and position the FM antenna wire in the direction where the strongest signal can be received.

Supplied AM loop antenna

Connect the AM loop antenna wire to the AM LOOP socket. Position the AM loop antenna for optimum reception.

Place the AM loop antenna on a shelf, etc., or attach it to a stand or a wall with screws (not supplied).

Notes :

Do not place the antenna on the main unit as it may result in noise pickup from the internal digital electronics.

Place the antenna away from the unit for better reception.

If the AM loop antenna and the FM antenna wire are placed near to the AC power cord, interference may result.

External FM antenna

Use an external FM antenna if you require better reception.

Consult your dealer.

9 EN

EX.BASS

/DEMO

2 “AA” size batteries (UM/SUM-3, R6, HP-7 or similar)

30

30

Demo mode

To enter into the demonstration mode:

When the unit is in the standby mode, press the EX.BASS/DEMO button again.

To cancel the demonstration mode :

Press the EX.BASS/DEMO button.

The demonstration mode will be cancelled and the unit will be in the low power consumption mode.

Notes :

When the unit is in the low power consumption mode, the display will disappear.

When the power is on, the EX.BASS/DEMO button can be used to select the extra bass mode.

When the power supply is restored after a power failure or the power cord is unplugged and plugged in again during use, this unit will enter into the demonstration mode.

Remote control

When inserting or removing the batteries, push them towards the battery terminals.

Installing the batteries incorrectly may cause the unit to malfunction.

Precautions for battery use :

Replace all old batteries with new ones at the same time. Do not mix old and new batteries.

Remove the batteries if the unit will not be used for long periods of time. This will prevent potential damage due to battery leakage.

Do not use rechargeable batteries (nickelcadmuim battery, etc.)

Note concerning use :

Replace the batteries if the operating distance is reduced or if the operation becomes erratic.

Periodically clean the transmitter LED on the remote control and the sensor on the main unit with a soft cloth.

Exposing the sensor on the main unit to strong light may interfere with operation. Change the lighting or the direction of the unit.

Keep the remote control away from moisture, excessive heat, shock, and vibrations.

10 EN

SETTING THE CLOCK

ON/

CLOCK

STANDBY

MEMORY

 

 

/SET

 

TUNING/

 

TIME (%UP

 

DOWN)

MEMORY /SET

CLOCK

TUNING/TIME (fi %)

POWER

2

3

4

5

6

7

8

9

In this example, the clock is set for the 24 hours (0:00) system.

1Press the ON/STANDBY button to enter the standby mode.

2 Press the CLOCK button.

3Within 5 seconds, press the MEMORY/SET button.

4Press the TUNING/TIME (%UP or fiDOWN) button to select the time display mode.

“0:00” : The 24-hours display will appear. (0:00 - 23:59)

“AM 0:00” : The 12-hours display will appear. (AM 0:00 - PM 11:59)

“AM 12:00” : The 12-hours display will appear. (AM 12:00 - PM 11:59)

Note that this can only be set when the unit is first installed or it has been reset (see page 37 - RESETTING THE MICROCOMPUTER).

5 Press the MEMORY/SET button.

6Press the TUNING/TIME (%UP or fiDOWN) button to adjust the hour.

Press the TUNING/TIME (%UP or fiDOWN) button once to advance the time by 1 hour. Hold it down to advance continuously.

When the 12-hours display is selected, “AM” will change automatically to “PM”

7 Press the MEMORY/SET button.

8Press the TUNING/TIME (%UP or fiDOWN) button to adjust the minutes.

Press the TUNING/TIME (%UP or fiDOWN) button once to advance the time by 1 minute. Hold it down to change the time in 5 minutes intervals.

The hour setting will not advance even if minutes advance from “59” to “00”.

9 Press the MEMORY/SET button.

The clock starts operating from “0” second. (Second are not displayed.)

And then the clock display will disappear after a few seconds.

11 EN

To see the time display :

Press the CLOCK button.

The time display will appear for about 5 seconds.

Note :

The clock display will flash on and off at the push of the CLOCK button when the AC power supply is restored after a power failure occurs or after the AC power cord is disconnected. If this happens, follow the procedure below to change the clock time.

To change the clock time :

1Press the CLOCK button.

2Within 5 seconds, press the MEMORY/SET button.

3Perform steps 6 - 9 on page 11 .

To change the time display mode :

1Perform steps 1 - 2 in the section “RESET-

TING THE MICROCOMPUTER”, on page 37.

2Perform step 1 - 9on page 11.

SETTING THE CHANNEL SPAN (Except for the Europe and U.K.)

The span between radio channels has been set to the one that prevails in the area to which the system is shipped. However, if the current channel span setting does not match the setting in the area where the system is to be used, for instance when you move from area 1 or area 2 shown in the following table or vice versa, proper reception of AM/FM broadcasts cannot be expected. In this case, change the channel span setting in accordance with your area by refering to the following table.

 

Area

 

CHANNEL

 

 

SPAN freq.

 

 

 

 

 

 

 

 

 

 

 

 

1

USA, Canada and Latin

FM : 100 kHz

 

America Countries

AM :

10 kHz

 

 

 

 

 

 

 

 

2

Other countries

 

FM :

50 kHz

 

 

 

 

 

 

AM :

9 kHz

 

 

 

 

 

 

 

1 Press the

 

 

 

ON/STANDBY button to enter

 

 

 

 

 

 

 

 

the standby mode.

 

 

2Set the SPAN SELECTOR switch to “50/9” for 9 kHz AM interval (50 kHz FM interval), and “100/ 10” for 10 kHz AM interval (100 kHz FM interval).

3Whilst pressing down the 7 STOP button and

the SOUND MODE button, hold down the

ON/STANDBY button for at least 1 second.

“CLEAR AL” will appear.

Caution :

The operation explained above will erase all data stored in memory including clock and timer settings, and tuner and CD presets.

12 EN

Loading...
+ 28 hidden pages