Kenwood XD-653, XD-503, XD-353, XD-753, XD-303 User Manual

...
0 (0)

COMPACT HI-FI SYSTEM

XD-SERIES

XD-653/ XD-753

XD-503/ XD-553

XD-303/ XD-353

XD-A33/ XD-A53/ XD-A73

INSTRUCTION MANUAL

KENWOOD CORPORATION

This instruction manual is used to describe multiple models listed above. Model availability and features (functions) may differ depending on the country and sales area. P

COMPACT

DIGITAL AUDIO

TEXT

B60-4473-00 01 MA (K, P, Y, M, X, T, E2)

9911

2 Before applying power

Caution : Read this page carefully to ensure safe operation.

 

Units are designed for operation as follows.

U.S.A. and Canada ............................................

AC 120 V only

Australia .............................................................

AC 240 V only

Europe and U.K. .................................................

AC 230 V only

China ....................................................................

AC 220 V only

*Other countries ...........

AC 110-120 / 220-240 V switchable

Preparation section

For the United Kingdom

Factory fitted moulded mains plug

1.The mains plug contains a fuse. For replacement, use only a 13-Amp ASTA-approved (BS1362) fuse.

2.The fuse cover must be refitted when replacing the fuse in the moulded plug.

3.Do not cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adapter, or consult your dealer.

If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.

IMPORTANT: The wires in the mains lead are colored in accordance with the following code: Blue : Neutral

Brown : Live

Do not connect those leads to the earth terminal of a threepin plug.

*AC voltage selection

The AC voltage selector switch on the rear panel is set to the voltage that prevails in the area to which the unit is shipped. Before connecting the power cord to your AC outlet, make sure that the setting position of this switch matches your line voltage. If not, it must be set to your voltage in accordance with the following direction.

AC voltage selector switch

Move switch lever to match your line voltage with a small screwdriver or other pointed tool.

AC 110120V~

AC 220240V~

Note:

Our warranty does not cover damage caused by excessive line voltage due to improper setting of the AC voltage selector switch.

Safety precautions

WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.

THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.

The marking of products using lasers

(Except for some areas)

CLASS 1

LASER PRODUCT

The marking is located on the rear panel and says that the component uses laser beams that have been classified as Class 1. It means that the unit is utilizing laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit.

The marking of products using lasers

(Except for some areas)

CAUTION

INVISIBLE LASER RADIATION

WHEN OPEN. AVOID EXPO-

SURE TO BEAM.

Inside this laser product, a laser diode classified as Class 3A laser radiation is contained as alerted by the internal caution label shown above. To avoid exposure to laser beams, do not open the cover.

 

 

 

 

Before applying power

3

 

 

 

 

 

 

 

 

Contents

 

 

 

 

Caution : Read the pages marked carefully to ensure safe operation.

 

 

 

 

 

 

 

 

 

 

Preparation section

 

 

Application section

 

 

 

 

 

 

 

 

Before applying power ..............................

2

Safety precautions ......................................

2

Special features ...............................................

4

Handling of discs and tapes ............................

5

System connection...........................................

6

Accessories .......................................................................

6

Connection of the system accessories .........................

6

Connection with other components (optional or com-

mercially-available equipment) .....................................

8

Controls and indicators .................................

10

Main unit ...........................................................................

10

Display ..............................................................................

12

Remote control unit ........................................................

13

Operation of remote control unit ..................

14

Operation of jog dials .....................................

15

Clock adjustment.............................................

16

Changing the display language ...................

17

Basic section

 

Let's have sound ..............................................

18

Basic operation ...............................................................

18

Playback of CD ................................................................

20

Tape playback ..................................................................

22

CHANNEL SPACE setting ................................................

25

Receiving broadcast station ..........................................

26

Let's record ......................................................

28

Recording on TAPE .........................................................

28

Copying tape (Tape dubbing) .........................................

31

As an ENERGY STAR® Partner, Kenwood Corporation has determined that this products meets the ENERGY

STAR® guidelines for energy efficiency.

This product can save energy. Saving energy reduces air pollution and lowers utility bills.

Playback of CD................................................

32

Listening in the desired sequence

 

(program playback) ...................................................

32

Repeated playback .........................................................

34

Random playback ............................................................

36

R.D.S. (Radio Data System)

 

 

(For U.K. and Europe) .................................

37

 

Preparation

 

Searching for a desired program type

 

 

 

 

 

 

 

(PTY search) ................................................................

38

 

 

Convenient CD recording ...............................

40

 

 

 

Selection of the recording type ....................................

40

section

 

Recording only desired titles

 

 

 

 

 

 

 

(CD ONE TRACK RECORDING) .................................

41

 

 

Recording of an entire CD

 

 

 

 

(CD DIRECT RECORDING) ..........................................

42

 

 

Recording the programmed titles

 

 

 

 

(CD PROGRAM RECORDING) ....................................

43

 

 

 

Effective sound adjustment ..........................

44

 

 

 

Balance adjustment.........................................................

44

Basic

 

Input level adjustment ....................................................

45

 

Listening to music with desired tone and sound field/

 

Switching the display (Equalizer effect and 3D surround

section

 

effect)

46

 

 

 

Equalizer pattern setting and saving............................

47

 

Timer operation...............................................

48

 

 

 

Sleep timer ........................................................................

48

 

 

Timer programming

49

 

 

 

 

Auto Power Save ..............................................................

50

 

 

Application

 

 

 

 

 

Knowledge section

 

 

 

 

 

 

 

 

 

 

 

Important Items ...............................................

52

 

section

 

Reference .........................................................................

52

 

Maintenance ....................................................................

52

 

In case of difficulty ........................................

53

 

 

Specifications

57

 

 

 

 

 

 

 

 

 

 

 

 

 

Knowledgesection

 

 

 

 

 

4 Special features

Simplified operations using large-sized, Jog Dial

Multi-control jog dial (For use in selecting a function)

This dial allows you to set the CD program and timer-related operations while observing the operating conditions shown by the display.

Multi language display function

The menu items for the operation can be displayed in any of five of languages, English, French, German, Spanish, and Italian.

Preparation section

Large-sized color display panel

The large sound level meter represents the movement in music with brilliant colors to offer the joy of viewing the music at the same time as listening.

3-Disc carousel CD player

Three discs can be set. There are various ways for enjoyment at the time of program playback, repeat playback, random playback, etc.

Convenient timer functions

Timer programming : Timer playback, AI timer playback, and timer recording can be pro-

 

grammed.

 

AI timer playback : When the unit is turned ON by the timer, the sound level

 

increases gradually.

Sleep timer

: Useful when you want to go asleep while listening to music.

Auto power save

When the power is ON and neither recording nor playback is executed for 30 minutes or more, the power is switched off automatically.

CD text information display (CD TEXT compatibility)

The text information (disc title and track titles) recorded into CDs can be displayed.

Demonstration

When the power supply is restored after a power failure or the power cord is unplugged and plugged in again during use, this unit automatically starts the demonstration function (display only). During the demonstration, the display changes in sequence but the sound mode does not change.

To cancel :

To switch on and off the demonstration :

Press the DISPLAY/DEMO key during demon-

Turn the unit OFF (STANDBY mode) and press the

stration to stop it.

DISPLAY/DEMO key.

DISPLAY

Each press of the key switches the demonstration

as shown below.

/DEMO

 

 

 

1

”Demo on“ (Demonstration on)

 

 

 

 

 

 

2

“Demo off” (Demonstration off)

 

 

 

DIGITAL AUDIO DIGITAL AUDIO
COMPACT
COMPACT

Handling of discs and tapes

5

 

 

Disc handling precautions

 

Handling

 

Hold the discs so that you do not touch

 

the playing surface.

 

Label side

 

Playing side

Sticker

Do not attach paper or tape to either

 

the playing side or the label side of the

 

discs.

Sticky paste

Cleaning

If fingerprints or foreign matter become attached to the disc, lightly wipe the disc with a soft cotton cloth (or similar) from the center of the disc outwards in a radial manner.

Storage

When a disc is not to be played for a long period of time, remove it from the player and store it in its case.

Discs which can be played with this unit

CD (12 cm, 8 cm), and the audio part of CDV, CD-G, CD-EG and CD-EXTRA.

Use discs that comply with the IEC standard, for example a disc carrying the marking on the label surface.

Never play a cracked or warped disc

During playback, the disc rotates at high speed in the player. Therefore, to avoid danger, never use a cracked or deformed disc or a disc repaired with tape or adhesive agent.

Please do not use discs which are not round because they may cause a malfunction.

Disc accessories

The disc accessories (stabilizer, protection sheet, protection ring, etc.) which are marketed for improving the sound quality or protecting discs as well as the disc cleaner should not be used with this system because they may cause malfunction.

Notes on cassette tape

Safety tab (accidental erasure prevention tab)

To store cassette tapes

After an important recording has been finished, break the

Do not store the tapes in a place which is subject to

safety tab, to prevent the recorded contents from being

direct sunlight, or near equipment that generates heat.

erased or recorded on accidentally.

Keep the cassette tapes away from any magnetic field.

section Preparation

For A side

For B side

N

S

When there is slack in the tape

In such a case, insert a pencil into the reel hole and wind the reel hub to remove the slack.

To re-record Apply tape only to the position where the tab has been removed.

1.Cassette tapes that are longer than 100 minutes

Notes Since tapes that are longer than 100 minutes are very thin, the tape could adhere to the pinch roller or be easily cut. It is recommended that these tapes not be used with this unit to prevent possible damage.

2.Endless tapes

Do not use an endless tape, as this could damage the mechanism of the unit.

6 System connection

Accessories

FM indoor antenna

AM loop antenna

(1)

(1)

AC plug adaptor (1)

 

Use to adapt the plug on the power cord to

 

the shape of the wall outlet.

section

(Accessory only for regions where use is

necessary.)

Preparation

Unpacking

 

Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost.

Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to you directly, notify the shipping company without delay. Only the consignee (the person or company receiving the unit) can file a claim against the carrier for shipping damage.

We recommend that you retain the original carton and packing materials for use should you transport or ship the unit in the future.

Keep this manual handy for future reference.

Remote control unit

Batteries (R6/AA)

(1)

(2)

 

 

Speaker cords (2) (XD-653 only)

Provided in the speaker package

Connection of the system accessories

CAUTION Note on Connection

Connect the components as shown in the diagram. Only plug the power cord into a power outlet once connections are completed. The rear panel configuration is variable depending on the models (countries or area).

FM indoor antenna

The accessory antenna is for temporary indoor use only. For stable signal reception we recommend using an outdoor antenna. Remove the indoor antenna if you connect one outdoors.

1 Connect to the antenna terminal.

2Locate the position providing good reception condition.

3 Fix the antenna.

ANTENNA

AM

GND

FM 75Ω

AM loop antenna

The supplied antenna is for indoor use. Place it as far as possible from the main system, TV set, speaker cords and power cord, and set it to a direction which provides the best reception.

ANTENNA

AM

GND

Assemble.

 

FM 75Ω

1

2

3

System connection 7

Speakers

The speaker illustration is of the XD-653.

Speaker (right)

 

− +

·

ª

Speaker (left)

 

− +

·

ª

System Name

 

Speaker Model Name

 

 

 

 

 

XD-303

 

 

LS-N303

 

 

 

 

 

 

XD-353/XD-A33

 

 

LS-N353

 

XD-503

 

 

LS-N503

 

XD-553/XD-A53

 

 

LS-N553

 

 

 

 

 

 

XD-653

 

 

LS-N653

 

XD-753/XD-A73

 

 

LS-N753

 

 

 

 

 

 

 

 

 

 

 

 

 

Main Unit

 

1

2

3

4

Speaker cord

+

-

R L

FRONT

SPEAKERS (6-16Ω )

Never short-circuit the “+” and “–” speaker cords.

If the left and right speaker connections or the “+” and “–” polarity are inverted, the sound will be unnatural with unclear positioning of musical instruments, etc. Be sure to connect them properly.

Twist

Speaker Unit (XD-653 only)

1

2

3

4

Twist

CAUTION

(For U.S.A., U.S.-Military and Canada)

Be sure to adhere followings. Or proper ventilation will be blocked causing damage or fire hazard.

Do not place any objects impairing heat radiation onto the top of unit.

section Preparation

 

1.Be sure to insert all connection cords securely. If their connections are imperfect, the sound may

Notes

not be produced or noise may interfere.

 

2.Before plugging or unplugging a connection cord, be sure to unplug the power cord from the wall

 

AC outlet. If connection cords are plugged or unplugged with the power cord left plugged in,

 

malfunction or damage may result.

 

 

Malfunction of microcomputer

If operation is not possible or erroneous display appears even though all connections have been made properly,

reset the microcomputer. Refer to “In case of difficulty”.

E

Speaker and TV installation

The magnet in the speaker may cause color irregularity on the TV. Place the speaker farther away from the TV set.

CAUTION

Be sure to adhere followings. Or proper ventilation will be blocked causing damage or fire hazard.

Do not place any objects impairing heat radiation onto the top of unit.

Leave a space around the unit (from the largest outside dimension including projection) equal or greater than, shown below.

Top panel : 50 cm

Side panel : 10 cm

Back panel : 10 cm

8

System connection

Connection with other components (optional or commercially-available equipment)

CAUTION Note on Connection

Connect the components as shown in the diagram. Only plug the power cord into a power outlet once connections are completed. The rear panel configuration is varies depending on the model (countries or area).

Preparation section

MD recorder, DVD player, VCR or analog turntable

MD recorder

 

DVD player/VCR/analog turn-

 

table (P-110/optional)

Digital

Audio

L

input

output

Audio output

 

 

R

 

 

DVD/VIDEO INPUT

Optical-fiber cable

 

 

For XD-753/653/XD-553/503

(Europe and U.K. only)

DIGITAL OUT

OPTICAL

DIGITAL OUT OPTICAL jack

Remove the cap and plug the optical-fiber cable.

Optical-fiber cable (Provided with the MD recorder)

DIGITAL OUT

OPTICAL

Cap

Insert the optical-fiber cable straight into the connector until it clicks.

Be sure to attach the protection cap when the connector is not used.

Never bend or bundle up the optical-fiber cable.

When an external system component is connected, please read the instruction manual of the Note component as well.

System connection 9

Surround (rear) speakers

Except for U.S.A. and Canada

R

 

L

− +

 

− +

· ª

ON

· ª

 

 

 

SURROUND

 

 

OFF

 

L

-+ R

SURROUND SPEAKERS (8-16Ω )

Surround switch

With regards to the SURROUND switch

This switch can be used only when the separately sold surround (rear) speakers are connected. When the switch is set to ON, surround playback can be enjoyed. When this switch is set to OFF, normal playback is executed.

ON

SURROUND

OFF

÷Please operate this switch while the power is switched off.

÷We recommend that this switch be set to OFF when no surround (rear) speakers are connected to obtain a better sound quality.

÷When the switch is set to OFF, no sound will come from the surround (rear) speakers.

Main Unit

1

2

3

4

Twist

Speaker Unit

1

2

3

4

FM outdoor antenna

Lead the 75coaxial cable connected to the FM out-

door antenna into the room and connect it to the FM 75terminal.

Use a commercially-available antenna adapter (a small-sized model).

ANTENNA

AM

Preparation

GND

 

FM

section

75Ω

 

Twist

Kenwood XD-653, XD-503, XD-353, XD-753, XD-303 User Manual

10 Controls and indicators

Main unit

 

 

 

 

 

 

# $ % ^

&

*

(

) ¡

 

section

1

STANDBY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DISC 1

 

 

2

 

 

 

 

 

 

 

 

 

 

Preparation

 

 

 

 

I/

 

 

 

 

DISC 3

£

5

SOUND

 

MENU TUNING

 

 

 

 

 

3

TIMER

 

 

 

 

 

 

DISC 2

 

 

4

DISPLAY/DEMO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

CONTROL

 

 

 

MODE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

 

 

CO

NT

 

 

 

 

VOLUME

 

¢

 

 

 

 

 

 

 

 

 

 

 

LTI

R

 

 

 

CONTROL

 

 

U

 

 

 

 

 

 

 

M

 

 

 

OL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

E

DISC SKIP

 

 

 

 

 

 

 

 

 

 

 

X

 

 

 

8

 

 

 

 

 

 

 

 

.

 

 

 

 

 

 

 

 

 

 

 

S

 

 

 

 

 

 

 

 

 

 

 

 

B

 

 

 

 

 

 

 

 

 

 

 

 

A

 

 

 

 

 

 

 

 

 

 

 

 

S

 

 

 

 

 

 

 

 

 

 

 

 

OPEN/

 

 

 

 

 

 

 

 

 

 

 

CLOSE

 

9

BACK

SELECT ENTER

 

 

 

REVERSE

REC/ARM TAPE EQ

 

 

0

 

 

 

MODE

§

 

 

 

 

 

 

 

 

 

 

 

 

!

 

 

PHONES

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

@

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ª

 

 

 

 

PUSH

 

 

 

 

 

PUSH

 

 

 

 

 

OPEN

 

 

 

 

 

OPEN

º

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DECK A

 

 

 

DECK B

 

 

 

 

 

PLAY

 

 

 

 

 

REC/PLAY

 

 

 

 

 

 

 

 

 

 

 

 

 

¤

CD player unit

#7(stop) key

¡

Operation key for the CD player and cassette deck.

(CD (6) key

¡

Press to select the CD and start playback.

 

Disc tray

)

Three discs can be stored.

 

£ DISC SELECTOR keys

¡

¢ DISC SKIP key

¡

The disc for playback (or recording) is selected.This is also used for loading CDs onto the disc tray.

0 OPEN/CLOSE key

)

The disc tray is opened and closed.

The disc for playback (or recording) is selected.

Controls and indicators 11

Receiver

1STANDBY indicator

* 0BACK key

%

The indicator lights up when the power is set to the

Press when setting a mode using the MULTI CON-

STANDBY mode.

 

 

TROL jog dial to return to the previous step and restart

2STANDBY (

 

 

) key

*

the operation from there.

 

 

 

 

STANDBY (POWER) key (For U.S.A. Canada)

!ENTER key

%

 

 

 

 

*

Used for entering a selected mode in memory or execut-

Power ON/OFF switching is executed.

ing it.

 

3TIMER indicator

 

Q @PHONES jack

*

The indicator lights up when the power is set to the

For connection of a headphone (optional).

 

STANDBY mode after having activated a timer pro-

#7 (stop) key

¡

gram.

 

 

Operation key for the CD player and cassette deck.

4DISPLAY/DEMO key

4y

When power is STANDBY:

 

Switches the displayed information.

Used for displaying the time. (When this key is pressed

5TUNING MODE key

 

while the “TIMER” indicator is lit, the timer icon and the

Switches the tuning mode.

 

timer reservation setting mode appears in the display,

6SOUND CONTROL key

y

then the display returns to the previous condition.)

Press to select the equalizer and 3D surround settings.

$AUX (DVD/VIDEO) key

*

7MENU key

 

%

Press to select the source connected to the DVD/VIDEO

Press to switch the mode set with the MULTI CON-

INPUT jacks.

 

TROL jog dial ON or OFF.

 

%Display

@

8MULTI CONTROL jog dial

%£§ *TUNER (BAND) key

§

Turn this dial to select optimum modes according to the

Press to select the tuner and switch the receiving band.

desired operations.

 

)VOLUME CONTROL knob

*

When the CD input is selected, this dial is used to skip

This is used for volume adjustment.

 

tracks.

 

 

¡EX. BASS (Extra bass) key

(

When the TUNER input is selected, this dial is used to

Switches the extra bass play on and off.

 

select a station.

 

 

 

 

When the TAPE input is selected, this dial is used to fast

 

 

forward or backward (rewind) the tape..

 

 

9SELECT key

 

%

 

 

section Preparation

Used for setting of various modes or establishing a selection.

Cassette deck unit

#7(stop) key

£ REVERSE MODE key

£ª

Operation key for the CD player and cassette deck.

The reverse mode of the deck (both sides, repeated,

^TAPE A (™£) key

one side) is switched.

 

Press to select the deck A and start playback.

 

ª 0 PUSH OPEN key (B)

 

&TAPE B (™£) key

Press to load or remove a tape.

 

Press to select the deck B and start playback.

 

º B deck cassette holder

 

§ TAPE EQ. key

£ A deck cassette holder

 

Press to switch the Tape Equalizer on and off.

 

¤ 0 PUSH OPEN key (A)

 

REC/ARM key

ª

Press to load or remove a tape.

 

Press to start recording. Pressing this key while recording pauses creates a non-recording space (blank) of about 4 seconds.

12

Display

Controls and indicators

The displays given in this manual are approximations only. They may differ from what actually appears on the display.

Preparation section

1

2

3

4

 

 

3D

T.EQ

 

 

BASS

 

 

 

REC

 

EQ

A B

 

 

 

 

TOTAL

• • • • • • • • • • MHz

1 2 3

PGM

PTY

AUTO

RPT. DISC ST.

 

 

RANDOM ALL

 

kHz

8

 

7

6

5

1 Timer-related indicators

2 Sound level meter

The display varies according to the music or the operations of the CD, tape, etc.

During the volume adjustment, this meter displays the current sound level as a reference.

3 Equalizer/3D surround/Ex. Bass indicators

4Cassette deck-related indicators

This section contains the cassette deck operation indicators. The indicated information includes the tape reverse mode and tape transport direction.

5Character information display

Displays the input selection, frequency, volume level, etc.

6 Tuner-related indicators

7 REPEAT/PGM/RANDOM/TOTAL indicators

8CD player-related indicators

This section contains the CD play and pause mode indicators.

Controls and indicators 13

Remote control unit

The keys on the remote control unit with the same names as on the main unit have the same function as the keys on the main unit.

1

DISC 1

DISC 2 DISC 3

 

POWER

 

 

 

#

 

 

 

 

 

 

1

2

3

CD

$

2

 

 

 

 

 

 

 

TUNER/BAND

 

 

4

5

6

%

 

 

 

 

 

 

 

 

7

8

9

TAPE A

^

 

 

 

 

 

 

 

 

0

+10

DISC

TAPE B

 

 

SKIP

 

&

 

 

 

 

 

 

 

 

P.CALL

*

 

 

 

 

3

 

MENU

 

 

4

 

SELECT

 

 

 

 

 

 

 

5

ENTER

BACK

 

STOP

(

6

 

 

 

 

TAPE EQ REV.MODE

TUNING

 

7

)

 

 

 

 

8

REPEAT RANDOM

PTY

RDS DISP

¡

9

TIME

TEXT DISP

 

 

 

 

0

AUX

EX.BASS SOUND CONT SLEEP

£

 

 

 

 

 

!

 

 

 

 

¢

@

MUTE VOLUME

1 DISC SELECTOR keys

¡

The disc for playback (or recording) is selected.

2 Numeric keys

¡

Used as number keys when the input is CD or TUNER.

3 MULTI CONTROL keys %£§

The left and right keys have the same functions as the MULTI CONTROL jog dial on the main unit.

P.CALL 4 ¢ (skip) keys (CD/TUNER)

¡¶

When the CD input is selected, press to skip forward or backward on the disc.

When the TUNER input is selected, press to select preset station.

When the TAPE input is selected, press the key to fastforward or rewind the tape.

SELECT key

%

MENU key

%

4 BACK key

%

5 ENTER key

%

6 REV. MODE key

£ª

The reverse mode of the deck (both sides, repeated, one side) is selected.

7 TAPE EQ key

£

8 RANDOM key

For CD playback, switching is executed between random playback and normal playback.

9 REPEAT key

Used for repeated playback of a CD.

 

0AUX key

*

Press to select the source connected to the DVD/VIDEO

INPUT jacks.

 

! EX. BASS key

(

@ MUTE key

(

This is used to mute the sound temporarily.

#POWER (

 

) key

*

 

 

Power ON/OFF switching is executed.

 

$CD (6) key

)

%TUNER/BAND key

§

^TAPE A (™ £) key

&TAPE B (™ £) key

* DISC SKIP key

¡

(7 STOP key

¡£

Operation key for the CD player and cassette deck.

) TUNING (1 ¡) keys (CD/TAPE/TUNER)

¡£§

When the CD or TAPE input is selected, press to fast forward or backward (rewind) the disc or tape.

When the TUNER input is selected, press to select a

station.

 

¡ TEXT DISP key

Press to switch the text information recorded in a CD TEXT disc.

RDS DISP key (For U.K. and Europe)

The display contents are switched during reception of RDS broadcasts.

SOUND CONTROL key

y

Press to select or the equalizer and 3D surround settings.

£ SLEEP key

i

Press to set the sleep timer.

 

¢ TIME key

¡

Press to switch the time information on the CD player unit.

PTY key (For U.K. and Europe)

°

This is used to specify the program type when searching for a station.

VOLUME keys

*

This is used for volume adjustment.

section Preparation

14 Operation of remote control unit

Loading batteries

1 Remove the cover.

2 Insert batteries.

3 Close the cover.

1

2

Preparation section

Insert two R6 (“AA”-size) batteries following the polarity indications.

Operation

Plug the power cord into the mains power outlet and press the on/standby ( POWER) key of the remote control unit to turn power ON. After the power has been turned ON, press the desired key.

Toturnpoweroff,presstheon/standby( POWER) key again.

The power mode enters the STANDBY mode in which the “STANDBY” indicator lights up. (The “TIMER” indicator also lights in this mode if a timer program has been activated.)

When pressing more than one remote control key successively, press the keys securely by leaving an interval of 1 second or more between the key presses.

Operating

range

 

(approx.)

 

Remote

 

 

sensor

6m

 

 

 

30˚

30˚

 

 

 

1.The provided batteries are intended for use in operation checking, and their service life may be short. Notes 2.When the remote controllable distance becomes short, replace both of the batteries with new ones.

3.If direct sunlight or the light of a highfrequency fluorescent lamp (inverter type, etc.) is incident to the remote sensor, malfunction may occur. In such a case, change the installation position to avoid malfunction.

Operation of the jog dial

15

 

 

This unit has a jog dial named the MULTI CONTROL jog dial.

The MULTI CONTROL jog dial makes it possible to set (establish) many functions in a simple procedure. When the MENU key is pressed, the items appears in the display according to the MULTI CONTROL jog dial operation so you can select the desired mode based on a more intuitive method.

You can also use the 4/¢ keys on the remote control unit instead of the MULTI CONTROL jog dial.

MENU

 

 

I CON

 

 

 

 

T

T

 

 

L

 

 

R

 

U

 

 

 

 

O

 

 

 

 

 

L

 

M

 

 

 

 

 

 

 

 

 

 

P.CALL

 

 

 

 

 

 

MENU

 

 

 

 

 

 

SELECT

 

 

 

 

 

 

ENTER BACK

STOP

BACK SELECT ENTER

MULTI CONTROL jog dial

1 Press the MENU key to enter the MULTI CONTROL setting mode.

2 Select an operation mode by turning the MULTI CONTROL jog dial (or pressing the MULTI CONTROL keys on the remote control unit).

3 Set, establish or execute (determine) items by pressing the SELECT key and/or ENTER key.

Display examples

The following items can be selected by turning the MULTI CONTROL jog dial.

“CD Program Play”

“Recording Options”

“Tape Dubbing”

“Audio Options”

“Clock Options”

“Language Options”

To cancel the mode for setting (using) MULTI CONTROL, read the description of each item in this manual.

Press the BACK key to return to the previous step and restart operation from there. (The BACK key is inoperative once scrolling message “Press ' ENTER ' to - - -” has been displayed.)

With the remote control unit, pressing the MENU key makes it possible to select the same items as those available on the main unit using the MULTI CONTROL keys.

section Preparation

In the MULTI CONTROL setting mode, only the volume control and 7STOP key are operative.

16 Clock adjustment

Preparation section

This unit incorporates a clock function. Be sure to adjust to the correct time before using the timer function. The time can be displayed only while the power is off.

1 Select “Clock Options”.

 

 

I CON

TR

 

 

LT

O

 

U

 

 

MENU

M

 

 

L

 

 

 

SELECT

 

 

 

 

2 Select “Adjust Time”.

 

I CON

TR

 

LT

O

U

 

 

M

 

 

L

SELECT

3 Adjust the hour.

 

I CON

TR

 

LT

O

U

 

 

M

 

 

L

SELECT

To decrease

To increase

the figure

the figure

4 Adjust the minute.

 

I CON

TR

 

LT

O

U

 

 

M

 

 

L

ENTER

To decrease

To increase

the figure

the figure

The following items can be selected by turning the MULTI CONTROL jog dial.

“CD Program Play” “Recording Options” “Tape Dubbing” “Audio Options”

“Clock Options”

“Language Options”

+Scrolled display (Clock Options)

C l o c k O p t i

The following items can be selected by turning the MULTI CONTROL jog dial.

“Sleep Timer”

“Adjust Time”

“Timer Play”

“Auto Power Save”

Example: Adjustment to 8:45

8 : 0 0

8 : 0 0 a m

(For U.K. and Europe)

(Other countries)

0Ô1Ô2...13Ô14...Ô0 ...

AM12ÔAM1ÔAM2...

 

PM1ÔPM2...ÔAM12 ...

The time display starts to blink.

Press the SELECT key. The hour is entered and the minute display starts to blink.

8 : 4 5

8 : 4 5 a m

(For U.K. and Europe)

(Other countries)

00Ô01Ô02...59Ô00Ô01...

Press the BACK key to return to the previous step and restart operation from there.

To adjust correct time, press the ENTER key at the same moment as a time announcement.

To display the time

(In standby mode)

The clock display blinks after the power cord has been unplugged from the AC power outlet and plugged in again or after a power failure. In this case, set the time of the day again.

(Displayed for approx. 5 sec.)

Changing the display language

17

 

 

You can change the display language manually.

1 Select “Language Options”.

 

I CON

TR

 

LT

O

U

 

 

M

 

 

L

MENU

SELECT

 

2 Select the desired language.

 

I CON

TR

 

LT

O

U

 

 

M

 

 

L

ENTER

The following items can be selected by turning the MULTI CONTROL jog dial.

“CD Program Play”

“Recording Options” “Tape Dubbing” “Audio Options” “Clock Options”

“Language Options”

+Scrolled display (Language Options)

L a n g u a g e O

The following items can be selected by turning the MULTI CONTROL jog dial.

“English” “Français” (French) “Deutsch” (German) “Español” (Spanish) “Italiano” (Italian)

section Preparation

When you do not recognize which language is displayed:

Press the MENU key and select “Language Options” (English), “Options de langue” (French),“SprachEinstellungen” (German), “Opción Idioma” (Spanish) or “Opzioni lingua” (Italian), then select the desired language.

About the beep sound

When you press the key, a beep sounds. The number of times that the beep sounds changes depending on the operation.

When a beep sounds

Once:

Normal operation

twice:

The MENU or ENTER key is pressed.

three times: Abnormal operation (The error message appears in the display.)

no sound: The key that cannot be operated is pressed.

You can also set the beep to OFF:

1 Select “Audio Options”.

 

I CON

TR

 

LT

O

U

 

 

M

 

 

L

2 Select “Beep sound”.

 

I CON

TR

 

LT

O

U

 

 

M

 

 

L

SELECT

3 Select “Beep on” or “Beep off”.

 

I CON

TR

 

LT

O

U

 

 

M

 

 

L

SELECT

1 “Beep on” 2 “Beep off”

MENU

SELECT

 

18

Let’s have sound

 

 

 

Basic operation

 

 

 

 

PHONES

 

Listening through headphones

 

 

Insert the headphone plug into the PHONES jack.

 

 

 

 

 

 

The sounds from all speakers are cut off.

 

 

 

1

 

 

 

 

2

 

 

 

 

 

Reproducing sound

 

 

 

 

with enhanced bass

 

 

 

3

(EX.BASS)

 

 

 

 

section

Muting the sound temporarily

Reproducing sound with enhanced bass

 

 

 

 

(MUTE)

(EX.BASS)

 

Basic

STANDBY

1. Switching the power ON (OFF)

 

 

 

 

 

 

1

When the power is ON, pressing the STANDBY key enters the power

 

STANDBY mode, in which the standby indicator lights up.

 

 

 

TIMER

 

 

 

 

 

2. Selecting the desired output

 

 

 

Select the desired source by pressing the AUX (DVD/VIDEO), TAPE A, TAPE

 

 

B, TUNER, or CD key.

 

 

2

 

When you press the TAPE A, TAPE B, or CD key, the unit starts playback

 

 

automatically.

 

 

 

If you select the AUX (DVD/VIDEO) (external input) mode, also read the

 

 

 

instruction manual of the component connected to the DVD/VIDEO INPUT

 

 

 

jacks.

 

 

VOLUME

3. Volume adjustment

 

 

CONTROL

 

 

E

 

 

 

 

X

 

 

 

 

.

 

 

 

 

B

The display shows a reference value. (The reference value is also shown visually by

 

A

 

S

 

S

 

 

 

 

 

 

the sound level meter.)

 

 

3

 

 

 

Loading...
+ 42 hidden pages