Kenwood DP-2060 User Manual

CD PLAYER

DP-2060

DP-1060

INSTRUCTION MANUAL

KENWOOD CORPORATION

This manual contains instructions for two models. Model availability and features (functions) may differ depending on the country and sales area.

DIGITAL AUDIO

B60-1680-08 (K,R,X,T) [AP]

TINSE0020AWZZ

Introduction

Your choice of this product indicates that you are a devotee to excellence in sound reproduction.

We appreciate your patronage and take pride in the long tradi­ tion of quality components that our company represents.

So that you can get the most out of your unit, 'NQ suggest that you take the time to read through this manual before you hook _ up and operate your system. This will acquaint you with oper­

ating	features and system-connection considerations				so	that
your listening pleasure will be enhanced		right	from the			start.
You will notice that in all aspects of		planning,		engineering,
styling,	operating convenience and adaptability		we	have	sought
to anticipate your needs and desires.
Keep this manual handy for future reference.
For your records
Record the serial number, found on the		back	of	the	unit, in

the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers

whenever you call upon your dealer		for information		or service
on this product.
Model_______________	Serial Number______________________
Unpacking
Unpack the unit carefully and make		sure	that all	accessories
are put aside so they will not be lost.
Examine the unit for	any possibility	of	shipping	damage. If

your unit is damaged or fails to operate, notify your dealer immediately, if your unit was shipped to you directly, notify the shipping company without delay. Only the consignee (the

person or company receiving the unit) can	file	a claim		against
the carrier for shipping damage.
We recommend that you retain the original	carton		and	pack­
ing materials for use should you transport	or	ship	the	unit in
the future.

For the U.S.A.

CAUTION:

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety.

KENWOOD CORPORATION 2967-3, ISHIKAWA-CHO, HACHIOJI-SHI,

TOKYO, JAPAN

i CENWOOD CORP. CERTIFIES THIS EQUIPMENT CONFORMS TO DHHS REGULATIONS NO. 21

I CFR 1040.10, CHAPTER I, SUBCHAPTER J.

ih_____ __________ _______

Location: Back Panel

The marking of products using lasers (Except for some areas.)

CLASSI

LASER PRODUCT

The label is attached to the rear panel and says that the com-ponent uses laser beams that have been classified as Class 1.

It means that the unit is utilizing laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit.

Contents	Caution: Read the pages marked zL carefully to ensure safe operation.
Introduction.............................	2	Remote control operation (DP-2060 only]..................	............9
Special features........................... ............................................	3	Normal playback (TRACK mode)............ ...................	....... 10..
A Before applying power..	3	....................................Programmed playback (PGM mode)	12
A Safety precautions.................	3	Editing (CCRS)...........................	......... 14
A IMPORTANT SAFEGUARDS ...............................	............ 4	Rep’eated playback..............................................	16
Before operation............	6	Timer operations...................................................	......... 17
System connections..	7	................................................In case of difficulty	......... ia_
Controls and indicators...............	_ 8	Specifications...............................................................	19

2 DP-2oeDjDPAoeo

Special features

Zh Caution: Read this page carefully to ensure safe operation.

Programmed Playback	................................................................... Up to 20 of your favorite tunes can be programmed in any
	order you want and can be played back.
	..This is an editing function that prevents the last tune on both
	sides A and B from being interrupted, within a stipulated time,
	when a CD is being recorded onto a cassette tape.

Before applying power

Units are designed for operation as follows.

U.S.A. and Canada.................................................	120 V only
U.K. and Australia..................................................	240 V only
Europe (Except for U.K.).......................................	230 V only
^ Other countries.................	110-120 / 220-240 V switchable
For the United Kingdom

Factory fitted moulded mains plug

4: AC voltage selection

The'AC voltage selector switch on the rear panel is set to the voltage that prevails in the area to which the unit is shipped. Before connecting the power cord to your AC outlet, make sure that the setting position of this switch matches your line voltage. If not, it must be set to your voltage in accordance with the following direction.

AC voltage selector switch

1.The mains plug contains a fuse. For replacement, use only a 13-Amp ASTA-approved (BS1362) fuse.

2.The fuse cover must be refittecf when replacing the fuse in the moulded plug,

3.Do not cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home, or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adaptor, or consult your dealer.

If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.

Our warranty does not cover damage caused by excessive line voltage due to improper setting of the AC voltage selector switch.

Safety precautions

WARNING:TO PREVENT EIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE

TO RAIN OR MOISTURE.

A 1 CAUTION 1 A			CAUTION; TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
			COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE, REFER SER­
			VICING TO QUALIFIED SERVICE PERSONNEL,
A		THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE,
		IS INTENDED TO ALERT THE USERTO THE PRESENCE OF UNINSULATED "DANGEROUS VOL­
		TAGE" WITHIN THE PRODUCT'S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE
		TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
A		THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE
		USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) IN­
		STRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE,

DP-2060/OP-1060 tEn) 3

IMPORTANT SAFEGUARDS ^ Caution: Read this page carefully to ensure safe operation.

Please read all of the safety and operating instructions before operating this appliance. Adhere to ail warnings on the appliance and in the instruction manual. Follow all the safety and operating instructions.-. .These safety and operating instructions should be retained for future reference.

1.Power sources - The appliance should be connected to a power supply only of the type described in the instruction manual or as marked on the appliance. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For appliances intended to operate from battery power, or other sources, refer to the instruction manual.

2.Power-cord protection - Power-supply cords should

be	routed so that they are not	likely to be walked on
or	pinched by items placed upon or against them,
paying particular attention to cords			at plugs,
convenience receptacles, and		the point	where they
exit from the appliance.

3. CAUTION - Polarization - This appliance may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your eiectriclan to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

4. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the appliance and to protect it from overheating, and these openings must not be blocked or covered. The appliance should be situated so that its location or position does not interfere with its proper ventilation.

To maintain good ventilation, do not put records or a table­ cloth on the appliance. Place the appliance at least 10 cm away from the wails.

Do not use the appliance on a bed, sofa, rug or similar surface that may block the ventilation openings. This appliance should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.

5.Water and moisture - The appliance should not be used near water - for example, near a bathtub,

washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc.

6. Temperature - The appliance may not function properly if used at extremely low, or freezing temperatures. The ideal ambient temperature is above +5°C (41 “F).

7.Heat - The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.

8.Electric shock-Care should be taken so that objects do not fall and liquid is not spilled into the enclosure

through openings, if a metal objects, such as a hair pin or a needle, comes rnto contact with the inside of this appliance, a dangerous electric shock may result. For families with children, never permit children to put anything, especially metal, inside this appliance.

9. Enclosure removal - Never remove the enclosure. If the internal parts are touched accidentally, a serious electric shock might occur.

10. Magnetic fields - Keep the appliance away from sources of magnetic fields such as TV sets, speaker systems, radios, motorized toys or magnetized objects.

11.Cleaning - Unplug this appliance from the wall

outlet before cleaning. Do not use volatile	solvents
such as alcohol, paint thinner, gasoline, or	benzine,
etc. to clean the cabinet. Use a clean dry cloth.

12.Accessories - Do not place this appliance on an unstable cart, stand, tripod, bracket, or table. The appliance mayfall, causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the appliance. Any mounting of the appliance should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

4 DP-206C/DP-1060 <En)

13.Lightning - For added protection for this appliance during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the appliance due to lightning and power-line surges.

14.Abnormal smell - If an abnormal smell or smoke is detected, immediately turn the power OFF and unplug theappliance from the wall outlet. Contact your dealer or

nearest service center.	POWER OFF*
15.Damage requiring service	- The appliance should

be serviced by qualified service personnel when;

A.The power-supply cord or the plug has been damaged.

B.Objects have fallen, or liquid has been spilled into

theappliance.

C.The appliance has been exposed to rain or water.

D.The appliance does not appear to operate normally by following the instruction manual. Adjust only those controls that are covered by the instruction manual as an Improper adjustment of othercontrols may result in damage and will often require extensive work by a qualiffed technician to restore the appliance to its normal operation.

E.The appliance has been dropped, or the enclosure

damaged.

F. Theappliance exhibits a marked change in performance.

16.Servicing - The user should not attempt to service the appliance beyond that described in the instruction manual. All other servicing should be referred to qualified service personnel.

17.Outdoor antenna grounding - If an outside antenna is connected to the appliance, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges. Article 810 of the National Electrical Code ANSI/ NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure.

Caution: Read this page carefully to ensure safe operation.

18.Power lines - An outside antenna system should not be located In the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits, When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

19.AC outlets - Do not connect other audio equipment

with a power consumption larger than that specified to the AC outlet on the rear panel. Never connect other electrical appliances, such asan iron or toaster, to it to prevent fire or electric shock.

20.Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

21.Attachment - Do not use attachments not recommended by the appliance manufacturer as they may cause hazards.

22.Replacementparts-When replacement partsare required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock, or other hazards.

23.Safety check - Upon completion of any service or repairs to this appliance, ask the service technician to perform safety checks to determine that the appliance is in proper operating condition.

Notes:

t. I tern 3 is not required except for grounded or polarized equipment.

2.Item 17 and 18 are not required except for units provided with antenna terminals.

3.Item 17 complies with UL in the U.S.A.

DP-2060iDP-t0eQ tEnl 5

Before operation

Disc handling precautions

Handling

Hold compact discs so that you do not touch the playing surface.

Do not attach paper or tape to either the playing side or the label side of compact discs,

Caution on disc used

Note related to transportation and movement

Cleaning

If fingerprints or foreign matter become attached to the disc, lightly wipe the disc with a soft cotton cloth (or similar) from the center of the disc outwards in a radial

Storage

When a disc is not to be played for a long period of time, remove it from the CD player and store it in its case.

Never play a cracked or warped disc.

During playback, the disc rotates at high speed in the player. Therefore, to avoid danger, never use a cracked or deformed disc or a disc repaired with tape or adhesive agent.

Before transporting or moving the CD PLAYER, carry out the following operations.

1.Turn the power ON but do not load a disc.

2.Wait a few seconds and verify that the display shown appears,

3.Turn the power OFF.

Beware of condensation

When water vapor comes into contact with the surface of cold material, water drops are produced.

If condensation occurs, correct operation may not be possible, or the unit may not function correctly.

This is nota malfunction, however, the unit should be dried. (Todothis, turn the POWER switch ON and leave the unit as it is for several hours.)

Be especially careful in the following conditions:

•When the unit is brought from a cold place to a warm place, and there is a large temperature difference.

•When a heater starts operating.

•When the unit is brought from an air-conditioned place to a place of high temperature with high humidity.

•When there is a large difference between the internal temperature of the unit and the ambient temperature, or in conditions where condensation occurs easily.

6 DP-2060yDP-1060 (En)