Kenmore 79092709013, 79092709014, 79092709015, 79092802010, 79092802011 Owner’s Manual

...

0 (0)

Use & Care Guide Guia de uso y cuidada

English / Espafiol

Model/Modelos:

I<en

coo s __©e% ee

790.9270%9280%9290 _

P/N 316902011 Rev A

Sears Brands Management Corporation Hoffman Estates, IL 60179 U.S.A.

www.kenmore.com www.sears.com

Table of Contents

Appliance Warranty ............................................................................. 2

Important Safety Instructions ......................................................... 3-6

Product Record/Serial Plate Location ............................................... 6

Before Setting Oven Controls .............................................................. 7

Removing, replacing & arranging the oven racks ....................... 7

Before Setting Surface Controls ..................................................... 8-10

Using proper ¢ookware .................................................................... 8

Cookware material types ................................................................. 8

Home canning ................................................................................... 10

Setting Surface Controls ................................................................. 11-14

Radiant surface element .................................................................. 11

Dual radiant surface element ........................................................ 12

Triple radiant surface element ...................................................... 13

Warm & Ready TM Zone .................................................................. 14

Oven Control Functions ....................................................................... 15

Setting Oven Controls ................................................................... 16-27

Setting clock ...................................................................................... 16

Setting timer ...................................................................................... 16

Add 1 minute ..................................................................................... 16

Setting 12 or 24 hour display mode .............................................. 16 Changing between continuous bake setting or 12-Hour

Energy Saving feature ..................................................................... 16

Changing oven temperature display (F:° or C°) .......................... 17

Setting silent or audible control mode ......................................... 17

Oven lockout ..................................................................................... 17

Setting Preheat ................................................................................. 18

Setting Bake ...................................................................................... 18

Setting Cook Time ............................................................................ 19

Setting Delay Start ........................................................................... 19

Setting Conv Bake or Convection Bake ....................................... 20

Setting Conv Roast (some models) ................................................ 21

Setting Cony Convert (some models) ............................................ 21

Broil .................................................................................................... 22

Slow Cook ......................................................................................... 23

Using AirGuard TM feature ............................................................. 23

Warm & Hold TM .............................................................................. 24

Recipe Recall ............................................................................. 24-25

Adiusting oven temperature .......................................................... 25

Setting the Sabbath feature .................................................... 26-27

Warmer Drawer ............................................................................ 28-29

Flex Clean ........................................................................................ 30-31

Care & Cleaning ............................................................................ 32-35

Cleaning recommendation table .................................................. 32

Cooktop maintenance and cleaning ...................................... 33-34

Removing and replacing lift-off oven door ................................ 35

Before You Call - Solutions to common problems ................... 36-38

Master Protection Agreement ............................................................ 39

Sears Service ......................................................................... back cover

Kenmore Limited Warranty

When installed, operated and maintained according to all instructions supplied with the product, if this appliance fails due to a defect in material and workmanship within one year from the date of purchase, call 1-800-4-MY-HOME® to arrange

for free repair. This warranty applies for only 90 days from the date of purchase if this appliance is ever used for other than private family purposes.

This warranty covers only defects in materlaJ and workmanship. Sears will NOT pay for:

1. Cracks in a ceramic glass cooktop that are not a result of thermal shock.

2. Stains and scratches on a ceramic glass cooktop resulting from failure to maintain it properly according to all instructions supplied with the product.

3. Expendable items that can wear out from normal use, including but not limited to filters, belts, light bulbs, and bags.

4. A service technician to instruct the user in correct product installation, operation or maintenance.

5. A service technician to clean or maintain this product.

6. Damage to or failure of this product if it is not installed, operated or maintained according to all instructions supplied with the product.

7. Damage to or failure of this product resulting from accident, abuse, misuse or use for other than its intended purpose.

8. Damage to or failure of this product caused by the use of detergents, cleaners, chemicals or utensils other than those

recommended in all instructions supplied with the product.

9. Damage to or failure of parts or systems resulting from unauthorized modifications made to this product.

Disclaimer of implied warranties; limitation of remedies Customer's sole and exclusive remedy under this limited warranty shall be product repair as provided herein. Implied

warranties, including warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest period allowed by law. Sears shall not be liable for incidental or consequential damages. Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, or limitation on the duration of implied warranties of merchantability or fitness, so these exclusions or limitations may not apply to you.

This warranty applies only while this appliance is used in the United States or Canada.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Important Safety Instructions

Read all instructions before using this appliance.

This manual contains important safety symbols and instructions. Please pay attention to these symbols and follow all instructions given.

Definitions

_This is the alert It is used to alert to potential personal injury hazards, Obey aJJ safety messages that follow this symbol to avoid possible injury or

death.

Do not attempt to install or operate your appliance until you have read the safety precautions in this manual. Safety

items throughout this manual are labeled with a WARNING or CAUTION statement based on the risk type.

situation which, if not avoided, may result in death or serious injury.

situation which, if not avoided, may result in minor or moderate injury.

safety symbol.

= indicates a potentially hazardous

- indicates a potentially hazardous

you

* All ranges can tip. * Injuw to persons could result. * Install anti=tlp device packed with

range.

* See ins|alia|ion ins|rue|ions.

To reduce the risk of tipping, the range must be secured by properly installed anti-tip bracket provided with the range. To check if the bracket is installed properly, visually check that

rear leveling leg is inserted into and fully secured by the anti-tip bracket by removing lower front panel or storage drawer from the range.

For models equipped with a warmer drawer or lower oven, grasp the top rear edge of the range and carefully attempt

to tilt it forward. Refer to the installation instructions for

proper anti- tip bracket installation.

" Remove all tape and packaging before using the range.

Destroy the carton and plastic bags after unpaddng the range. Never allow children to play with packaging

material.

* Proper instaliatlon--Be sure your appliance is properly

installed and grounded by a qualified technician in

accordance with the National Electrical Code ANSI/

NFPA No. 70 latest edition and local electrical code requirements. Install only per installation instructions

provided in the literature package for this range.

. User servlclngmDo not repair or replace any part of the

appliance unless specifically recommended in the manuals. All other servicing should be done only by a qualified technician, This may reduce the risk of personal

injury and damage to the range.

Ask your dealer to recommend a qualified technician and an authorized repair service. Know how to disconnect the power to the range at the circuit breaker or fuse box in

case of an emergency.

Never modify or alter the construction of a range by removing the leveling legs, panels, wire covers, anti=tip brackets/screws, or any other part of the range.

Remove the oven door from any unused range if it is to

be stored or discarded.

Do not attempt to operate the range during a power

failure. If the power fails, always turn off the range. If

the range is not turned off and the power resumes, the range will begin to operate again. Once the power

resumes, reset the clock and oven function.

Stepplng, leaning or sitting on the door or

drawers of a range can result in serious injuries and also

cause damage to the appliance. DO NOT allow children to climb or play around the range. The weight of a child on

an open oven door may cause the range to tip, resulting in serious burns or other injury.

Storage in or on appliance m flammable

materials should not be stored in an oven, near surface units or in the storage drawer, warmer drawer or lower

oven. This includes paper, plastic and cloth items, such as cookbooks, plasticware and towels, as well as flammable

liquids. Do not store explosives, such as aerosol cans, on or near the range.

Save these instructions for future reference.

Important Safety Instructions

NEVER cover any slots, holes or passages in

the oven bottom or cover an entire oven rack with materials

such as aluminum foil. Aluminum toll linings may trap heat, causing a fire hazard.

DO NOT LEAVE CHILDREN ALONE m

children should not be left alone or unattended in the area where appliance is in use. They should never be

allowed to sit or stand on any part of the appliance, including the storage drawer, lower broiler drawer, warmer

drawer or lower double oven.

Do not store items of interest to children in the cabinets above a range or on the backguard of the range. Children climbing on the range to reach items

could be seriously injured.

DO NOT TOUCH SURFACE HEATING UNITS, OR SURFACE COOKING ELEMENTS, AREAS

NEAR THESE SURFACE HEATING UNITS, OR INTERIOR SURFACE OF THE OVEN. Both surface heating and oven

heating elements may be hot even though they are dark in color. Areas near surface cooking units may become hot enough to cause burns. During and after use, do not touch, or let clothing or other flammable materials touch these

areas until they have had sufficient time to cool. Among these areas are the cool< top, surfaces facing the cool< top, the oven vent openings and surfaces near these openings,

oven door and oven door window.

Wear proper apparel -- loose-fitting or hanging garments should never be worn while using the appliance. Do not let clothing or other flammable

materials contact hot surfaces.

DO NOT USE WATER OR FLOUR on grease fires m smother the fire with a pan lld, or use baking soda, a dry chemical or foam=type extinguisher.

When heating fat or grease, watch if closely. Fat or grease may catch fire if allowed to become too hot.

Use dry potholders m moist or damp potholders on hot surfaces may result in burns from

steam. Do not let potholders touch hot heating elements. Do not use a towel or other bulky cloth instead of a

pothoider.

Do not heat unopened food containers

buildup of pressure may cause container to burst and

result in injury.

Important Safety Notice

The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of

substances known to the state to cause cancer, birth defects or other reproductive harm, and requires businesses to warn customers of potential exposure to such substances.

IMPORTANT INSTRUCTIONS FOR USING YOUR

OVEN

Protective Liners = DO NOT USE ALUMINUM FOiL to llne the oven bottom. Only use aluminum foil as recommended in this manual. Improper installation of these liners may result in risk of electric

shock, or fire.

Use care when opening oven door, warmer drawer or

lower oven door = Stand to the side of the range when opening the door of a hot oven. Let hot air or steam

escape before you remove or replace food in the oven.

Keep oven vent ducts unobstructed. The oven vent is

located below the backguard. Touching the surfaces in

this area when the oven is operating may cause severe

burns. Also, do not place plastic or heat-sensitive items on or near the oven vent. These items could melt or

ignite.

Placement of interior oven racks. Always place oven

racks in desired location while oven is cool. If rack must be moved while oven is hot use extreme caution. Use potholders and grasp the rack with both hands to

reposition. Do not let potholders contact the hot heating elements in the oven. Remove aii utensils from the rack

before moving.

* Do not use the broiler pan without its insert. The broiler

pan and its insert allow dripping fat to drain and be kept away from the high heat of the broiler.

* Do not cover the broiler insert wlfh aluminum foil.

Exposed fat and grease could ignite.

Save these instructions for future reference.

Important Safety Instructions

iMPORTANT iNSTRUCTiONS FOR USING YOUR

COOKTOP

* Know which knob controls each surface heating unit.

Place a pan of food on the surface element unit before

turning it on, and turn the element off before removing the pan.

* Use proper pan size m This appliance is equipped with

one or more surface units of different sizes. Select utensils having flat bottoms large enough to cover the

surface unit heating element. The use of undersized utensils wiii expose a portion of the heating element to direct contact and may result in ignition of clothing.

Proper relationship of utensil to element wiii also improve

efficiency.

* Utensil handles should be turned inward and not e×tend

over adjacent surface elements m To reduce the risk of

burns, ignition of flammable materials, and spillage due to unintentional contact with the utensil, the handle of the utensil should be positioned so that it is turned inward, and does not extend over adjacent surface units.

iMPORTANT iNSTRUCTiONS FOR CERAMIC- GLASS COOK TOP MODELS

* Do not cook on broken cook top---If cool< top should

break, cleaning solutions and spillovers may penetrate

the broken cool< top and create a risk of electric shock.

Contact a qualified technician immediately.

* Clean cook top with ca_|on---If a wet sponge or cloth is

used to wipe spills on a hot cooking area, be careful to avoid a steam burn. Some cleaners can produce noxious fumes if applied to a hot surface.

o Never leave surface elements unattended at high heat

settings _ Boilovers cause smoking and greasy spillovers that may ignite, or a pan that has boiled dry may melt.

• Glazed cooking utensils _ Only certain types of glass, glass/ceramic, ceramic, earthenware, or other glazed

utensils are suitable for cool< top service without breaking due to the sudden change in temperature. Check the

manufacturer's recommendations for cook top use.

• When flaming foods under a ventilating hood, turn the

fan on.

Save these instructions for future reference.

Important Safety Instructions

iMPORTANT iNSTRUCTiONS FOR CLEANING

YOUR RANGE

Before manually cleaning any part of the

range, be sure aii controls are turned OFF and the range is COOL. The range may be hot and can cause burns.

• Clean the range regularly to keep all parts free of grease that could catch fire. Pay particular attention to

the area around each surface element. Do not allow

grease to accumulate.

* Kitchen cleaners and aerosols m Always follow the

manufacturer's recommended directions for use. Be aware that excess residue from cleaners and aerosols

may ignite causing damage and injury.

* Clean ventilating hoods frequently m Grease should not

be allowed to accumulate on the hood or filter. Follow

the manufacturer's instructions for cleaning hoods.

iMPORTANT iNSTRUCTiONS FOR SELF-

CLEANING OVENS

* Clean in the self-cleanlng cycle only the parts listed in

thls Use & Care Manual. Before self-cleaning the oven,

remove the oven racks, broil pan, broil pan insert and any cookware, cooking utensils or foods from the oven.

° Do Not Use Oven Cleaners -- No commercial oven

cleaner or oven liner protective coating of any kind should be used in or around any part of the oven.

° Do Not Clean Door Gasket -- The door gasket is

essential for a good seal. Care should be taken not to rub, damage or move the gasket.

The health of some birds is extremely sensitive to the

fumes given off during the self-cleaning cycle of any range. Move birds to another well-ventilated room.

Save these instructions for future reference.

Product Record

In this space below, record the date of purchase, model and serial number of your product. You will find the model

and serial number printed on an identification plate. See bottom of fhls page for serial plate location.

Model No. 790.

Serial No.

Date of Purchase

Save sales receipt for future reference.

Serial Plate Location

To locate the serial plate open warmer drawer (some models) or storage drawer (some models). The serial plate is attached

to the lower right oven frame.

Before Setting Oven Controls

Oven vent location

The oven vent is located under the left side of the control panel (See Fig. 1). When the oven is on, warm air passes

through this vent. This venting is necessary for proper air circulation in the oven and good baking results. Do not

block oven vent.

oven vent

Fig. 1

Removing, replacing and arranging racks

Always use pot holders or oven miffs when

using the oven. When cooking, the oven interior and

exterior, oven racks and cooktop will become very hot which can cause burns.

Protective Liners m DO NOT USE ALUMINUM FOiL to llne the oven bottom. Only use aluminum foil as recommended in this manual. Improper installation of these liners may result in risk of electric

shock, or fire.

Arranging - always arrange the oven racks when the oven

is cool (prior to operating the oven).

Types of oven racks

flat handle

oven rack

___offset oven rack

ttom

rack

oven

The flat oven rack (some models) or flat handle oven rack (some models) may be used for most cooking needs.

The offset oven rack (some models) is designed to place the base of the rack about 1/2 of a rack position lower than fiat oven racks. This design provides several additional possible positions between the flat rack positions.

To maximize oven cooking space place the bottom oven rack (on some models) in the lowest rack position for roasting large cuts of meat.

To remove - pull the rack forward until it stops. Lift up

front of rack and slide out.

To replace - fit oven rack onto the rack guides on both

sides of oven walls. Tilt the front of oven rack upward

and slide the rack back into place. Be sure oven racks are level before using.

Fig. 2

some models

Recommended oven rack positions by food type:

Food type Position

Broiling Cookies, cakes, pies, biscuits & muffins

See broil 4or5

Frozen pies, angel food cake, yeast, bread

and casseroles

Small cuts of meat or poultry Turkey, roast or ham

2or3 1or2

1or2

Fig. 3

Air circulation in the oven

For best baking results allow 2-4" (5-10 cm) around the cookware for proper air circulation and be sure pans and

cookware do not touch each other, the oven door, sides or back of the oven cavity. Hot air must be able to circulate

around the cookware in the oven for even heat to reach around the food (See Fig. 3 ).

Baking layer cakes with I or 2 oven racks

For best results when baking cakes or cookies using 2 oven racks, place cookware on rack positions 2 and 5 (6 using the offset oven rack on some models). For best results when baking cakes or cookies using a single oven rack, place cookware on rack in positions 2, 3 or 4 (See Fig. 2).

Before Setting Surface Contro&

Using proper cookware

The size and type of cookware used wiii

influence the radiant element power levei

setting needed for best

cooking results. Be sure to follow the

recommendations for using proper cookware as

illustrated in both Figs. 1 &2.

Fig. 1

Check for flatness by rotating a ruler across the bottom of the cookware (See Fig. 1). Cool<ware should have flat

bottoms that make good contact with the entire surface heating element (See Fig. 2). For more detailed information about the ceramic cooktop see Cooktop maintenance and Cooktop cleaning in the Care & Cleaning section.

Cookware material _ypes The cookware material determines how evenly and quickly

heat is transferred from the surface element to the pan bottom. The most popular materials available are:

Aluminum - Excellent heat conductor. Some types of food will cause it to darken (Anodized aluminum cookware resists staining & pitting). If aluminum pans slide across the ceramic cooktop_ they may leave metal marks which wiil resemble scratches. Remove these marks immediately.

Copper - Excellent heat conductor but discolors easily. May leave metal marks on ceramic glass (see Aluminum).

Stainless - Slow heat conductor with uneven cooking results. Is durabie_ easy to clean and resists staining.

Cast iron - A slow heat conductor however wiii retain heat very well. Cooks evenly once cooking temperature is reached. Not recommended for use on ceramic cooktops.

Porcelaln-enamel on metal - Heating characteristics wiii vary depending on base material. Porcelain-enamel coating must be smooth to avoid scratching ceramic

cooktops.

° Flat bottom and straight

sides.

° Tight fitting lids. ° Weight of handle does

not flit pan. Pan is well balanced.

° Pan sizes match the

amount of food to be

prepared and the size

of the surface element.

° Made of material that

conducts heat well.

" Easy to dean. ° Always match pot

diameter to element

size.

'_ .........

• Curved and warped pans.

Cookware larger than

cooking area marked on cooktop by more than

one-half inch or 12mm.

• Heavy handle flits pan.

• Pan is smaller than the heating area marked on cooktop.

Fig. 2

Glass - Slow heat conductor. Not recommended for ceramic cooktop surfaces because it may scratch the glass.

important note:

Do not place empty aluminum, glass or porcelain-enamel coated cookware on the ceramic cooktop! The melting point of cookware made with these materials may be reached quickly especially if left empty & they may bond to the ceramic cooktop. If the cookware melts it wiii

damage the cooktop! Be sure to follow aii the cookware manufacturer's suggestions when using any type of cookware on the ceramic cooktop.

Before Setting Surface Controls

About the ceramic glass cooktop

The ceramic cooktop has radiant surface elements located below the surface of the glass. The design of the ceramic cooktop outlines the area of the surface element underneath. Be sure to match the pan size with the

diameter of the element outline on the cooktop and only flat-bottomed cool<ware should be used.

The type and size of cookware, the number of surface elements in use and their settings are all factors that will

affect the amount of heat that will spread to areas beyond the surface elements. The areas surrounding the elements may become hot enough to cause burns.

About the radiant surface elements

The element temperature rises gradually and evenly. As the temperature rises, the element will glow red. To maintain the selected setting the element will cycle ON and OFF. The heating element retains enough heat to provide a

uniform and consistent heat during the off cycle.

For efficient cooking, turn OFF the element several minutes before cooking is complete. This will allow residual heat to complete the cooking process.

Element On & Hot Surface indicator lights

Your appliance is equipped with two different types of surface control indicator lights that will glow on the control panel -- the ELEMENT ON indicator light and the Hot Surface indicator lights (See Fig. 1).

The ELEMENT ON indicator light is marked on the control panel and wiii glow when a surface element is turned ON. A quick glance at this indicator light after cooking is an easy check to be sure ALL surface controls are turned OFF.

The Hot Surface indicator lights are located on the control panel just above each surface control knob. They will glow when any surface cooking area heats up and will remain on until the cooktop has cooled to a MODERATE level.

ELEMENT ON

Hot Surface _ O O

Radiant surface elements may appear to have cooled after they have been turned off. The glass surface may still be hot and burns may occur if the glass

surface is touched before it has cooled sufficiently.

Do not place plastic items such as salt and pepper shakers, spoon holders or plastic wrappings on fop of the range when if is in use. These items could melt or ignite. Potholders, towels or wooden spoons could catch fire

if placed too close to the surface elements.

Do not allow alumlnum foil, empty glass/ porcelain cookware or ANY materlal that can melt to

make contact wlfh the ceramic cookfop. If these items melt on the cooktop they may damage the ceramic cooktop.

Fig. 1

Important notes: ° Radiant elements have a iimiter that allows the radiant

heating element to cycle ON and OFF, even at the HI setting. This helps to prevent damage to the ceramic smoothtop. Cycling at the HI setting is normal and will

occur more often if the cool<ware is too small for the radiant element or if the cookware bottom is not fiat.

° Be sure to read the detailed instructions for ceramic glass

cooktop maintenance and cleaning in the Care & Cleaning and Before You Call checklist sections of this

Use & Care Guide.

Before Setting Surface Controls

Types of cooktop surface elements

The ceramic glass cooktop has radiant surface elements located below the surface of the glass. The patterns on the

ceramic glass will outline the size and type of element available.

The single radiant element or elements will have one round outline pattern shown on the cooktop. The warmer zone feature located on the center rear area of the cooktop uses one round outline and is designed to keep food warm only.

The dual (some models) radiant element allows the user to set the smaller inner portion as a single element or both

inner and outer portions may be set to heat together (See Fig. 1).

The trlple (some models) radiant element feature has 3 element portions and may be set to heat as 1 (single)0 2

(dual) or 3 (triple) element portions together (See Fig. 2).

WARMER ZONE EtE_NTON

@ @ @ ©

Turbo Boil feature (some models)

Your appliance may be equipped with one or two elements on the ceramic cooktop marked TURBO BOIL.

These higher wattage radiant elements are best used when bringing larger quantities of liquid to temperature and

when preparing larger quantities of food.

Home Canning

Be sure to read and observe all the following points when

home canning with your appliance. Check with the USDA (United States Department of Agriculture) website and be

sure to read aii the information they have available as weii as follow their recommendations for home canning procedures.

* Use only quality fiat bottom canners when home canning.

Use a straight-edge to check canner bottom.

Center Right Rear Right Front

Warmer Zone Single Dual element control

control element

(some models) control

Fig. 1 (models with right front dual element)

WARMER ZONE _L_NTON

@ @ @

Center Right Rear Right Front

/? TRIPLE

* Use only a completely flat bottom canner with no ridges

that radiate from the bottom center when home canning

using a ceramic cooktop.

Make sure the diameter of the canner does not exceed 1

inch beyond the surface element markings or burner. It is recommended to use smaller diameter canners on

electric coil and ceramic glass cooktops.

* Start with hot tap water to bring water to boil more

quickly.

* Use the highest heat seating when first bringing the water

to a boil. Once boiling is achieved_ reduce heat to lowest

possible setting to maintain that boil.

NEVER place or straddle a cooking utensil over 2

different surface cooking areas at the same time. This

will cause uneven heating results and may cause the

ceramic cooktop to fracture.

ELEMENT

Warmer Zone Single

control element

(some models) control

Triple element control

Fig. 2 (models with right front triple element)

Setting Surface Controls

Radiant surface element settings

The size and type of utensil used, and the amount and type of food being cooked wiil influence the surface element

power level setting needed for best cooking results.

The suggested settings found in Fig. 1 below are based when cooking with medium-weight aluminum pans with

lids. Settings may vary when using other types of pans.

Suggested settings for single, dual and triple radiant surface elements table

Settings Type of cooking

High (HI - 9) Start most foods, bring water to a

boil, pan broiling

Medium high (7 - 8) Continue a rapid boil, fry, deep

fat fry

Medium (5 - 6) Maintain a slow boil, thicken

sauces and gravies or steam vegetables

Medium Low (2 - 4) Keep foods cooking, poach, stew

Low (LO - 1) Keep warm, melt, simmer

Fig. 1

Radiant surface elements may appear to have cooled after they have been turned off. The glass surface may still be hot and burns may occur if the glass

surface is touched before it has cooled sufficiently.

Do not place plastic items such as salt and

pepper shakers, spoon holders or plastic wrappings on top of the range when it is in use. These items could melt or ignite. Potholders, towels or wooden spoons could catch fire if placed too close to the surface elements.

I_ Do not allow aluminum foil, empty glass/ porcelain cookware or ANY materlal that can melt to

make contact wlth the ceramic cooktop. If these items melt on the cooktop they may damage the ceramic cooktop.

Fig. 2

Single radiant surface elements (all models)

To operate the single radiant element:

1. Place correctly sized cookware on single radiant surface

element.

2. Push in and turn the surface control knob in either direction to the desired setting (See Fig. 2).

3. When cooking is complete, turn the radiant surface element OFF before removing the cookware.

important notes: ° For efficient cooking, turn OFF the element several

minutes before cooking is complete. This will allow residual heat to complete the cooking process.

The surface control knobs do not have to be set exactly on a particular spot. Use the graphics provided as a guide and adjust the control knob as needed. Each

surface element provides a constant amount of heat at each setting. Refer to the Suggested radiant surface

element settings table for suggested power level settings.

° Start most cooking operations on a higher setting and

then turn to a lower setting to finish cooking.

Radiant elements have a limiter that allows the radiant heating element to cycle ON and OFF, even at the HI

setting. This helps prevent damage to the ceramic smoothtop. Cycling at the HI setting is normal and will

occur more often if the cookware is too small for the radiant element or if the cookware bottom is not flat.

° A glowing red surface heating area extending beyond

the bottom edge of the cookware indicates the cookware

is too small for the surface heating area.

Setting Surface Contro&

Dual radiant surface element (some models)

To operate the dual radiant element:

1. Place correctly sized cookware on single radiant surface element.

2. Pushin and turn the surface control knob clockwise to

begin heating both the inner and outer portions of the element (marked dual - See Fig. 2). If only the inner heating portion is needed (marked single - See Fig. 1) for smaller cookware, push in and turn the knob counter-

clockwise to start.

Please note that you may switch from the single or dual

settings at any time during cooking.

3. When cooking is complete, turn the radiant surface element OFF before removing the cookware.

Important notes: ° For efficient cooking, turn OFF the element several

minutes before cooking is complete. This will allow residual heat to complete the cooking process.

RJont Front

Right Front

000

° The surface control knobs do not have to be set exactly

on a particular spot. Use the graphics provided as a guide and adjust the control knob as needed. Each surface element provides a constant amount of heat at each setting. Refer to the Suggested radiant surface

element settings table for suggested power level settings.

° Start most cooking operations on a higher setting and

then turn to a lower setting to finish cooking.

Radiant elements have a limiter that allows the radiant

heating element to cycle ON and OFF, even at the HI setting. This helps prevent damage to the ceramic smoothtop. Cycling at the HI setting is normal and will

occur more often if the cookware is too small for the radiant element or if the cookware bottom is not fiat.

° A glowing red surface heating area extending beyond

the bottom edge of the cookware indicates the cookware

is too small for the surface heating area.

Fig. 1 Fig. 2

Heating with inner Heating with both

(small) element only elements

Areas that heat are shown darkened.

Radiant surface elements may appear to have cooled after they have been turned off. The glass surface may still be hot and burns may occur if the glass surface is touched before it has cooled sufficiently.

Do not place plastic items such as salt and

pepper shakers, spoon holders or plastic wrappings on fop

of the range when it is in use. These items could melt or ignite. Potholders, towels or wooden spoons could catch fire

if placed too dose to the surface elements.

Do not allow aluminum foil, empty glass/ porcelain cookware or ANY materlal that can melt to

make contact wlfh the ceramic cookfop. If these items melt on the cooktop they may damage the ceramic cooktop.

+ 28 hidden pages