K 2.93
5.961-609.0 03/05
HIGH PRESSURE WASHER OPERATOR MANUAL
Overview |
|
3 |
|
|
Important Safety Instructions |
4-5 |
|
||
Operating Instructions |
|
6 |
|
|
GFCI Instructions |
|
7 |
|
|
Using the Accessories |
|
7 |
|
|
Working with Detergents |
8 |
|
||
Shut Down & Clean Up |
|
9 |
|
|
Care and Maintenance Instructions10 |
|
|||
Taking a Break |
|
10 |
|
|
Winterizing and Long-Term Storage10 |
|
|||
Cleaning Tips |
|
11-12 |
|
|
Optional Cleaning Accessories |
13-14 |
|
||
Troubleshooting |
|
15-16 |
|
|
|
|
|
|
|
Specifications |
|
|
||
|
|
|
|
|
Operating pressure |
|
1400 PSI |
|
|
|
|
|
|
|
Water volume |
|
1.3 GPM |
|
|
|
|
|
|
|
Amp draw |
|
10 AMPS |
|
|
|
|
|
|
|
Voltage |
|
120 V |
|
|
|
|
|
|
|
Part No. |
|
1.601-103.0 |
|
|
|
|
|
|
|
Serial no. |
|
|
|
|
|
|
|
|
|
Kärcher Customer Support USA
Call: 1-800-537-4129 for help or visit our website: www.karcher-usa.com
Safety Alert Symbols
DANGER
indifies ’’an imminently hazardous situation which, if not avoided, will result in death or serious injury.’’
WARNING
indifies ’’a potentially hazardous situation which, if not avoided, could result in death or injury.’’
CAUTION
indifies ’’a potentially hazardous situation which, if not avoided, may result in minor or moderate injury’’ or in property damage incidents.
2 English
MODEL OVERVIEW
Item Description:
1 Detergent suction tube
2 ON/OFF switch
3 High pressure outlet
4Water inlet with garden hose connector
5 Transport handle
6Power cord with Ground Fault Circuit Interrupter (GFCI)
7 Trigger gun
8 Trigger gun safety lock
9 High pressure hose
10 Vario Spray wand
11 Dirtblaster® (Rotating spray wand)
CAUTION
Follow the maintenance instructions specified in the manual
This machine has been designed for use with cleaning detergents by the manufacturer. The use of other cleaning detergents may affect the operation of the machine and void the warranty.
For household use only !
English 3
IMPORTANT SAFETY INSTRUCTIONS
WARNING! |
! Do not use acids and solvents in this |
|
|
product. These products can cause |
|
When using this product basic precauti- |
physical injuries to the operator and |
|
irreversible damage to the machine. |
||
ons should always be followed, inclu- |
||
! To reduce the risk of electrocution, |
||
ding the following: |
||
keep all connections dry and off the |
||
! Read all the instructions before |
||
ground. Do not touch plug with wet |
||
using the product. |
||
hands. |
||
! To reduce the risk of injury, close su- |
||
! The Trigger Gun Safety Lock PRE- |
||
pervision is neccessary when a pro- |
||
duct is used near children. |
VENTS the trigger from accidentally |
|
being engaged. This safety feature |
||
! Know how to stop the product and |
||
DOES NOT lock trigger in the ON |
||
bleed pressures quickly. Be thoroug- |
||
position. |
||
hly familiar with the controls. |
||
! Do not use extention cord for this |
||
! Stay alert — watch what you are |
||
unit. |
||
doing. |
||
WARNING |
||
! Do not operate the product when fa- |
||
tigued or under the influence of alco- |
To reduce the risc of electrocution, keep |
|
hol or drugs. |
all connections dry and off the ground. |
|
! Keep operating area clear of all per- |
Do not touch plug with wet hands. |
|
|
||
sons. |
|
|
Grounding Instructions |
||
! Do not overreach or stand on unsta- |
||
|
||
ble support. Keep good footing and |
This product must be grounded. If it |
|
balance at all times. |
should malfunction or breakdown, |
|
! Follow the maintenance instructions |
grounding provides a path of least resi- |
|
specified in the manual. |
stance for electric current to reduce the |
|
! This Product Is Provided With A |
risk of electric shock. This product is |
|
Ground Fault Circuit Interrupter (GF- |
equipped with a cord having an equip- |
|
CI) Built Into The Power Cord Plug. |
ment-grounding conductor and a groun- |
|
If Replacement Of The Plug Or Cord |
ding plug. The plug must be plugged |
|
Is Needed, Use Only Identical Re- |
into an appropriate outlet that is proper- |
|
placement Parts. |
ly installed and grounded in accordance |
|
! Risk of Injection or Injury to persons |
with all local codes and ordinances. |
|
- Do not direct discharge stream at |
DANGER |
|
persons. |
Improper connection of the equipment- |
|
! High pressure jets can be dangerous |
grounding conductor can result in a risk |
|
if subject to misuse. The jet must not |
of electrocution. Check with a qualified |
|
be directed at persons, animals, |
electrician or service personnel if you |
|
electrical devices, or the machine |
are in doubt as to whether the outlet is |
|
itself. |
properly grounded. Do not modify the |
|
! Wear safety goggles. |
plug provided with the product - if it will |
|
|
not fit the outlet, have a proper outlet in- |
4 English
stalled by a qualified electrician. Do not use any type of adapter with this product.
Ground Fault Circuit Interrupter
(GFCI) Protection
This product is supplied with a Ground Fault Circuit Interrupter (GFCI) built into the power cord plug. This device provides additional protection from the risk of electric shock. If power is interrupted in the line, the GFCI will automatically reclose the circuit to the load after power is restored. Depending on the GFCI model, it may be necessary to manually operate the reset button to restore power to the GFCI load circuit. If replacement of the plug or cord is needed use identical replacement parts.
SAVE THESE INSTRUCTIONS!
WATER SUPPLY (Cold Water Only)
CAUTION
Dirt in the feed water will damage the unit. To avoid this risk, we recommend fitting a water filter.
!Water hose must be at least 5/8 inch in diameter.
!Flow rate of water supply must not fall below 2 GPM (gallons per minute).
!Flow rate can be determined by running the water for one minute into an empty 5-gallon container.
!The water supply temperature must not exceed 104°F/40°C.
!Never use the pressure washer to draw in water contaminated with solvents, e.g. paint thinners, gasoline, oil, etc.
!Always prevent debris from being drawn into the unit by using a clean water source.
English 5
OPERATING INSTRUCTIONS
"STEP 1: Connect the high pressure hose to the unit’s high pressure outlet.
"STEP 4: Connect garden hose to the cold water source and turn water on completely. Plug the power cord into the power outlet.
"STEP 2: Insert the spray wand of your choice to the trigger gun. Press in against the spring tension and twist into locked position.
"STEP 3: Connect garden hose to unit’s water inlet.
"STEP 5: Unlock the Safety lock. Trigger the gun to eliminate trapped air, wait for a steady flow of water to emerge from the spray nozzle.
"STEP 6: Turn on the high pressure washer (I).
The motor starts only if the trigger of the gun is pulled and shuts off when the trigger is released.
6 English
GFCI INSTRUCTIONS |
|
" STEP 1: Plug the Ground Fault Cir- |
|
cuit Interrupter (GFCI) into a working |
1 2 |
outlet. |
|
" STEP 2: Press ’’TEST’’, then press |
|
’’RESET’’ to assure proper connec- |
|
tion to power. |
|
Note: The actual appearance of the |
|
GFCI may be different from this illu- |
|
stration. |
|
USING THE ACCESSORIES
WARNING
To avoid serious injury never point spray nozzle at yourself, other persons or animals.
Vario power nozzle
!The Vario power spray wand allows you to adjust the cleaning pressure. To clean at maximum pressure, the wand must be positioned to the high pressure setting (Max).
For lower pressure turn the wand collar in the minus (Min) direction. To apply detergent, the wand must be positioned to the low pressure setting (Min).
Max |
Min |
Dirtblaster®
!This nozzle features a 0º pencil jet which rotates 360º for maximum dirt cutting action, effectively increasing cleaning performance up to 50%. This nozzle combines the cleaning performance of a 0º pencil jet with the surface coverage of a wide angle nozzle.
Not recommended for soft materials, siding, painted surfaces, decks or autos.
English 7
WORKING WITH DETERGENTS
Detergents can only be applied at low pressure (Min).
"STEP 1: Install the vario power nozzle. Set the spray wand to the low pressure setting (Min).
For best results see Cleaning Tips on pages 11 & 12 for specific information on how to clean different surfaces.
Always Use Kärcher Detergent for Best
Min |
"STEP 2: Fill the detergent reservoir with Kärcher detergent. Place the filter end of detergent suction tube into the detergent reservoir
"STEP 3: Turn on the pressure washer (1). Pull trigger to operate unit: Liquid detergent is drawn into the unit and mixed with water. Apply detergent to work area. Do not allow detergent to dry on surface.
Results
Kärcher biodegradable detergents are specially formulated to protect the environment and your pressure washer. Special formula won’t clog the suction tube filter and will protect the internal parts of the pressure washer for a longer life. For Kärcher Detergents, check your retailer or call our service center for help.
The following Kärcher detergents are available:
One Gallon ready to use
!Vehicle Wash
!All Purpose Cleaner
!Deck Wash
!Degreaser
!House Wash
CAUTION
Never use:
–Bleach, Chlorine products and other corrosive chemicals
–Liquids containing solvents (i.e., paint thinners, gasoline, oils)
–Tri-sodium phosphate products
–Ammonia products
–Acid-based products
These chemicals will harm the unit and will damage the surface being cleaned.
8 English
SHUTTING DOWN & CLEAN-UP
" STEP 1: Remove detergent suction |
" STEP 5: Disconnect the garden |
||||
tube from container and insert into 1 |
|
hose from the water inlet on the unit. |
|||
gallon of fresh water. Siphon water |
|
|
|
||
at low pressure for one minute. |
|
|
|
||
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
"STEP 2: Turn the switch to off (O) position and unplug cord from outlet.
" STEP 3: Turn off the water source.
"STEP 4: Press trigger to release water pressure.
"STEP 6: Disconnect the high pressure hose from the high pressure outlet.
"STEP 7: Release trigger and engage gun safety lock.
English 9
TAKING A BREAK ..five minutes or more
" STEP 1: Release trigger and engage |
" STEP 2: Turn pressure washer to off |
||||||
gun safety lock. |
(O) position. |
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
WINTERIZING AND LONG-TERM STORAGE
"1: Disconnect all water connections.
"2: Turn on the machine for a few seconds, until the water which had remained in the pump exits, turn off immediately.
"3: Do not allow high pressure hose to become kinked.
"4: Store the machine and accessories in a room which does not reach
freezing temperatures. DO NOT store near furnace or other sources of heat as it may dry out the pump seals.
CAUTION
Failure to follow the above directions will result in damage to the pump assembly and accessories.
CARE AND MAINTENANCE INSTRUCTIONS
Cleaning the water inlet filter |
Maintenance |
Pull out the water inlet filter with flat- |
The unit is maintenance-free. |
nose pliers and rinse out in warm water. |
|
10 English
CLEANING TIPS
Deck Cleaning
(with or without detergent). Pre-rinse deck and surrounding area with fresh water. If using Kärcher Deck Wash, apply to surface at low pressure. For best results, limit your work area to smaller sections of approximately 25 square feet. Allow Deck Wash to remain on surface 1-3 minutes. Do not allow detergent to dry on surface. Rinse at high pressure in a long sweeping motion keeping the spray nozzle approximately 3-6 inches from the cleaning surface. Always clean from top to bottom and from left to right. When moving on to a new section of the cleaning surface, be sure to overlap the previous section to eliminate stop marks and ensure a more even cleaning result.
House Siding
(with or without detergent). Pre-rinse cleaning surface with fresh water. If using Kärcher Pressure Wash, apply to surface at low pressure (for best results, limit your work area to sections of approximately 6 feet and always apply detergent from bottom to top). Allow Pressure Wash to remain on surface 1- 3 minutes. Do not allow detergent to dry on surface, if surface appears to be drying, simply wet down surface with fresh water. If needed, use special wash brush attachment (not included) to remove stubborn dirt. Rinse at high pressure from top to bottom in an even sweeping motion keeping the spray nozzle approximately 6 inches from the cleaning surface.
Cement Patios, Brick and Stone
(with or without detergent). Pre-rinse cleaning surface with fresh water. If using Kärcher Pressure Wash or Degreaser, apply to surface at low pressure. For best results, limit your work area to smaller sections of approximately 25 square feet. Allow Pressure Wash or Degreaser to remain on surface 1-3 minutes. Do not allow detergent to dry on surface. Rinse at high pressure in a sweeping motion keeping the spray nozzle approximately 3-6 inches from the cleaning surface. Always clean from top to bottom and from left to right. For removing extremely stubborn stains, use the Dirtblaster Nozzle.
Cars, Boats & Motorcycles
(with or without detergent). Pre-rinse vehicle with fresh water. If using Kärcher Touchless Vehicle Wash, apply to surface at low pressure. For best results, clean one side of vehicle at a time and always apply detergent from bottom to top, do not allow detergent to dry on surface. If needed, use special wash brush attachment (not included) to remove stubborn dirt. Rinse at high pressure in a sweeping motion keeping the spray nozzle approximately 6-8 inches from the cleaning surface (distance should increase when rinsing pin-stri- ping or other sensitive surfaces). Always clean from top to bottom and from left to right. For best results, wipe surface dry with a chamois or soft dry cloth.
English 11
Barbecue Grills, Outdoor Power
Equipment & Gardening Tools
(with or without detergent). Pre-rinse cleaning surface with fresh water. If using Kärcher Pressure Wash or Degreaser, apply detergent at low pressure. Allow Pressure Wash to remain on surface 1-3 minutes.Do not allow detergent to dry on surface. Rinse at high pressure keeping the spray nozzle approximately 3-6 inches from the cleaning surface. For removing extremely stubborn dirt, it may be necessary to move the spray nozzle even closer to the surface for greater dirt cutting action.
Patio & Lawn Furniture
(with or without detergent). Pre-rinse furniture and surrounding area with fresh water. If using Pressure Wash, apply to surface at low pressure. Allow Pressure Wash to remain on surface 1- 3 minutes. Do not allow detergent to dry on surface. If needed use special Wash Brush Attachment (not included) to remove stubborn dirt. Rinse at high pressure in a sweeping motion keeping the spray nozzle approximately 3-6 inches from the cleaning surface. For best results, clean from top to bottom and from left to right.
Recommendations
!Before cleaning any surface an inconspicuous area should be cleaned to test spray pattern and distance for maximum cleaning results.
!If painted surfaces are peeling or chipping, use extreme caution as pressure washer may remove the loose paint from the surface.
!When using on surfaces which might come in contact with food, flush surfaces with plenty of drinking water.
12 English
OPTIONAL CLEANING ACCESSORIES
Optional cleaning accessories are available to further enhance your cleaning capabilities: See accessories order form for product descriptions and ordering instructions.
Pump Guard
Specially formulated to protect your pressure washer from freezing, corrosion and premature wear. The Pump Guard also adds lubrication to valves and seals to prevent sticking. Highly recommended for all Karcher pressure washers!
Part No. 9.556-999.0
Water Pumping Kit
Attach this accessory to your pressure washer to quickly pump large quantities of water out of a standing source, such as a barrel or bucket. Fits most Karcher pressure washers up to 2300 PSI.
Part No. 2.637-214.0
25 Ft. Extension /Replacement High-
Pressure Hose
Replacement hose fits Kärcher pressure washer with screw-on type gun connections from 2400psi to 2500psi, Extension Hose for all Kärcher high pressure washers between the original equipment hose and machine up to 2500 psi.
Part No. 2.640-850.0
66" Extension Wand (Four piece)
Need to clean second story windows or other high areas? Increase the reach of your pressure washer by up to 66" with this extension kit. Includes 4 aluminum sections for variable length. 66" fully as-
sembled. Fits most Karcher pressure washers up to 2300 PSI. (bayonet)
Part No. 2.640-746.0
Rotating Wash Brush (bayonet)
For more effortless cleaning of all smooth surfaces (painted, glass and plastic) try Karcher's Rotating Wash Brush. Use it on your automobile, house siding or windows. The water pressure from your pressure washer causes the inner brushes to gently spin, making your cleaning job much easier. The angle of brush head is adjustable to help you reach difficult areas. Excellent for the application of detergent. A musthave accessory designed for Karcher pressure washers up to 2300 PSI. (bayonet)
Part No. 2.640-743.0
Soft Clean Washing Brush
Made with soft bristles that will not harm painted surfaces. Easily attaches directly to the trigger gun. Ideal for stubborn dirt on cars, boats, patio furniture and other surfaces. Great for applying detergent. Fits most Karcher pressure washers up to 2300 PSI. (bayonet)
Part No. 2.640-740.0
25 ft. Pipe Cleaning Kit (bayonet)
Need to clean blocked pipes, drains or downspouts? Karcher's pipe cleaning kit is the answer! The pipe cleaner propels itself forward while simultaneously flushing out debris. For example, insert the cleaning nozzle in the base of a downspout, pull the trigger on the pressure washer gun and watch as the
English 13
nozzle shoots out leaves and other debris while climbing upward. Connects directly to the trigger gun of most Karcher pressure washers up to 2300 PSI. (bayonet)
Part No. 2.640-747.0
Wet Sandblasting Kit (bayonet)
Why spend hours stripping old paint and rust by hand using harsh chemicals? Let Karcher's Wet Sandblasting Kit do the work! Attach the kit to your pressure washer, add abrasive material and attack the rust and paint with our eco-fri- endly alternative. Fits most Karcher pressure washers up to 2300 PSI. (bayonet)
Part No. 2.638-792.0
Detergent Foamer Attachment
Ideal for applications which require a thick foam. Simply fill the resevoir cup with liquid pressure washer detergent to generate a foam spray. Connects directly to the trigger gun. Fits most Karcher pressure washers up to 2300 PSI. (bayonet)
Part No. 6.964-507.0
T-Racer Wide Area Surface Cleaner
For cleaning surfaces such as patios, terraces and driveways without splashback, there is no better solution than Karcher's T-Racer. It saves time by cleaning a 12" wide area gently as it hovers, providing consistent, streak-free cleaning. When you finish cleaning the patio and driveway, remove the wand and use the handle to clean garage doors and other vertical surfaces. Includes two height-adjustable nozzles which spin at high speed for optimum results. Our top selling accessory for Karcher pressure washers up to 2300 PSI. (bayonet)
Part No. 2.640-508.0
Kärcher Customer Support USA
Call: 1-800-537-4129 for help or visit our website: www.karcher-usa.com
14 English
TROUBLESHOOTING
CAUTION |
Disconnect the machine from the power |
|
|
source before making any repair. |
|
Symptom |
Cause |
Solution |
|
|
|
Motor will not start |
On/Off switch is in the “OFF” |
Turn switch to the “ON” (I) posi- |
|
(O) position. |
tion |
|
|
|
|
Power cord is not plugged in.d |
Plug in power cord. |
|
|
|
|
Electrical outlet does not supply |
Try a different outlet. |
|
adequate power. |
|
|
|
|
|
Tripped circuit breaker. |
Switch off pressure washer. |
|
|
The reset will be automatically, |
|
|
for that wait that the tempera- |
|
|
ture goes down. |
|
|
|
Unit does not reach |
Diameter of garden hose is too |
Replace with a 5/8 inch garden |
high pressure. |
small. |
hose. |
|
|
|
|
Water supply is restricted. |
Check garden hose for kinks, |
|
|
leaks and blockage. |
|
|
|
|
Not enough inlet water supply. |
Open water source full force. |
|
|
|
|
Water inlet filter is clogged. |
Remove filter and rinse out in |
|
|
warm water. |
|
|
|
|
Spray wand is on low pressure |
Turn spray wand to high pres- |
|
position. |
sure position. |
|
|
|
Output pressure va- |
Not enough inlet water supply. |
Turn water on full force. Check |
ries high and low. |
|
garden hose for kinks, leaks or |
|
|
blockage. |
|
|
|
|
Pump is sucking air. |
Check that hoses and fittings |
|
|
are air tight. Turn off machine |
|
|
and purge pump by squeezing |
trigger gun until a steady flow of water emerges through the nozzle.
Water inlet filter is clogged.
Remove filter and rinse out in warm water.
Discharge nozzle is obstructed. Blow out or remove debris with
|
|
a fine needle. |
|
|
|
|
Calcified gun, hose or spray |
Run distilled vinegar through |
|
wand. |
detergent suction tube. |
|
|
|
English 15