JVC LVT2141-001B, KW-NT3HDT, KW-NT3HD User Manual

GPS NAVIGATION SYSTEM

SISTEMA DE NAVEGACIÓN GPS

SYSTÈME DE NAVIGATION GPS

KW-NT3HDT / KW-NT3HD

FRANÇAIS ESPAÑOL ENGLISH

HD Radio Traffic is available only for KW-NT3HDT. HD Radio Traffic se encuentra disponible sólo con el KW-NT3HDT.

HD Radio Traffic est disponible uniquement pour le KW-NT3HDT.

For installation and connections, refer to the separate manual. Para la instalación y las conexiones, refiérase al manual separado.

Pour l’installation et les raccordements, se référer au manuel séparé.

INSTRUCTIONS

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

Only for KW-NT3HDT

Sólo para KW-NT3HDT

Uniquement pour le

KW-NT3HDT

For customer Use:

Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet. Retain this information for future reference.

Model No.

Serial No.

LVT2141-001B

[J/C]

ENGLISH

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit.

IMPORTANT FOR LASER PRODUCTS

1.CLASS 1 LASER PRODUCT

2.CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to

	qualified service personnel.
3.	CAUTION: (For U.S.A.)	Visible and/or invisible class II laser radiation when open. Do not stare into beam.
	(For Canada)	Visible and/or invisible class 1M laser radiation when open. Do not view directly with
		optical instruments.
4.	REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

INFORMATION (For U.S.A.)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

–Reorient or relocate the receiving antenna.

–Increase the separation between the equipment and receiver.

–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

–Consult the dealer or an experienced radio/TV technician for help.

Caution

Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.

(For USA)

CAUTION: This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. End user cannot modify this transmitter device. Any unauthorized modification made on the device could avoid the user’s authority to operate this device.

(For Canada) “The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population, consult Safety Code 6, obtainable from Health Canada’s website www. hc-sc.gc.ca/rpb”

The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met.

This device complies with RSS 210 of Industry Canada “IC”. “Operation is subject to the following two conditions:

(1)this device may not cause interference, and

(2)this device must accept any interference, including interference that may cause undesired operation of the device.”

L’ utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’ utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.

2

Cautions on the monitor:

•The monitor built in this unit has been produced with high precision, but it may have some ineffective dots. This is inevitable and is not malfunction.

•Do not expose the monitor to direct sunlight.

•Do not operate the touch panel using a ball-point pen or similar tool with the sharp tip.

Touch the buttons on the touch panel with your finger directly (if you are wearing a glove, take it off).

•When the temperature is very cold or very hot...

–Chemical changes occur inside, causing malfunction.

–Pictures may not appear clearly or may move slowly. Pictures may not be synchronized with the sound or picture quality may decline in such environments.

•Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

•“DVD Logo” is a trademark of DVD Format/Logo Licensing Corporation registered in the US, Japan and other countries.

•HD Radio™ Technology Manufactured Under License From iBiquity Digital Corp. U.S. and Foreign Patents.HD Radio™ and the HD and the HD Radio and Arc logos are proprietary trademarks of iBiquity Digital Corp.

•“SIRIUS” and the SIRIUS dog logo are registered trademarks of SIRIUS Satellite Radio Inc.

•XM and its corresponding logos are registered trademarks of XM Satellite Radio Inc.

•“SAT Radio,” the SAT Radio logo and all related marks are trademarks of SIRIUS Satellite Radio Inc., and XM Satellite Radio, Inc.

•Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

•The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Victor Company of Japan, Limited (JVC) is under license. Other trademarks and trade names are those of their respective owners.

WARNINGS:

To prevent accidents and damage

•DO NOT install any unit or wire any cable in a location where;

–it may obstruct the steering wheel and gearshift lever operations.

–it may obstruct the operation of safety devices such as air bags.

–it may obstruct visibility.

•DO NOT operate the unit while driving.

If you need to operate the unit while driving, be sure to look around carefully.

•The driver must not watch the monitor while driving.

[European Union only]

•“Made for iPod”, and “Made for iPhone” mean that an electronic accessory has been designed to connect

specifically to iPod, or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.

•This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Rovi Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Rovi Corporation. Reverse engineering or disassembly is prohibited.

•Google Maps™ is a trademark of Google Inc.

•SD Logo is a trademark.

Only for KW-NT3HDT:

•HD Total Traffic Network® + is a registered mark of Clear Channel in the United States and other countries and hereby used under license.

•Journaline® technology licensed by Fraunhofer IIS. http://www.journaline.info

ENGLISH

3

ENGLISH

For safety...

•Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.

•Stop the car before performing any complicated operations.

Temperature inside the car...

If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit.

When replacing/rotating the tires:

It is required to clear all the accumulated calibration data which is important for accurate navigation. To clear the data, perform <Reset Calibration Data>. ( page 39)

Detaching/attaching the monitor panel

Detaching

1

2

3

How to forcibly eject a disc

Soft case (supplied)

[Hold]

Attaching

•Be careful not to drop the disc when it ejects.

•If this does not work, detach the monitor panel then attach it ( right).

How to read this manual:

Caution:

•Hold the monitor panel securely so as not to drop it accidentally.

•Fit the monitor panel onto the attaching plate until it is firmly locked.

•Illustrations of KW-NT3HDT are mainly used for explanation.

•< > indicates the variable screens/menus/operations/settings that appear on the touch panel.

•[ ] indicates the buttons on the touch panel.

4

Contents

How to forcibly eject a disc .......................................................		4
Detaching/attaching the monitor panel....................................		4
Introduction..........................................		8
Parts identification..................................................................		8
Installation settings ................................................................		9
Basic operations ....................................................................		10
• Turning on the power .....................................................................		10
• Messages about the status of GPS signal reception.........................		10
• Turning off/on the screen ...............................................................		10
• Operations on the touch panel........................................................		11
Switching screens ..................................................................		12
Navigation System .............................		14
Safety instructions/information for the Navigation System......		14
• Information/icons on the map ........................................................		14
Basic operations ....................................................................		15
• About the current position screen...................................................		15
• To change the map scale.................................................................		15
• To scroll the map.............................................................................		16
• To display your current position......................................................		16
• To change the map view.................................................................		16
Registering your home/favorite points ...................................		17
Searching for a place..............................................................		18
• Setting a destination by scrolling the map......................................		18
• About the search result screen........................................................		18
• Setting a destination using the <Destination Menu>....................		19
• About search screens and input screens..........................................		20
•	By address <Address> ...................................................................	21
• By telephone number <Phone> ....................................................		22
• From the list of POI <POI Name>...................................................		23
• POI near a place/route <Vicinity>..................................................		24
•	By coordinates <Coordinates>.......................................................	25
• From the list of POIs imported by yourself <Assistant POIs>..........		25
•	Quick Search ...................................................................................	26
How you are guided ...............................................................		28
• Starting guidance to the destination or via point............................		28
•	Changing route options ..................................................................	29
•	Canceling guidance.........................................................................	29
• Adjusting the volume of the voice guidance ...................................		29
• About route guidance screen ..........................................................		30
• Getting information on your route and places ................................		31

ENGLISH

5

Contents

ENGLISH

Arranging your route .............................................................		32
• Changing the sequence of the destination/via points .....................		32
• Avoiding a congestion ahead..........................................................		33
• Adjusting the vehicle position.........................................................		33
Editing registration of home/favorite points ...........................		34
Only for KW-NT3HDT
Using information service ......................................................		35
• Using the traffic information service ...............................................		35
• Using the area information service
	(Total Traffic HD NET WORK Service) ...............................................	37
Checking the information of the navigation system.................		38
Initializing memories/navigation settings ..............................		39
Navigation menu items..........................................................		40
Additional information ..........................................................		42
AV Operations.....................................		44
Common operations on AV screens..........................................		44
• Selecting the playback source.........................................................		44
• Turning off the AV source................................................................		44
Listening to the HD Radio™ broadcast .....................................		45
• Changing HD Radio reception mode ...............................................		46
• Storing stations in memory.............................................................		46
• Selecting a preset station................................................................		47
•	Reducing the interference...............................................................	47
• Tagging/purchasing your favorite songs from iTunes Store ............		48
Disc operations......................................................................		50
•	Playable disc types..........................................................................	51
•	Selecting playback modes...............................................................	55
• Settings for the disc playback..........................................................		56
SD/USB operations.................................................................		57
Listening to the iPod/iPhone device........................................		59
• Selecting a track/video from menu on the iPod/iPhone..................		61
Listening to the satellite radio ...............................................		62
• Storing channels in memory ...........................................................		64
•	Selecting preset channels ...............................................................	64
• Selecting a channel quickly.............................................................		64
Using other external components...........................................		65
•	Front AUX........................................................................................	65
•	AV-IN ..............................................................................................	65

6

Sound equalization................................................................	66
Changing illumination color ...................................................	67
Settings for video playback ....................................................	68
• Picture adjustment .........................................................................	68
• Changing the aspect ratio ...............................................................	68
AV menu items ......................................................................	68
Additional information ..........................................................	72
Bluetooth Operations ........................	74
Information for using Bluetooth® device.................................	74
Using Bluetooth device ..........................................................	75
• Registering a Bluetooth device .......................................................	75
• Connecting/disconnecting a registered Bluetooth device ...............	76
• Deleting a registered Bluetooth device ...........................................	76
Using Bluetooth mobile phone ...............................................	77
• Receiving a call ...............................................................................	77
• Adjusting the volume of calls/earpiece ...........................................	77
• Switching between handsfree mode and phone mode...................	78
• Making a call...................................................................................	78
• Copying the phone book .................................................................	79
• Searching for a phone number from phone book............................	79
• Deleting the phone number memory in the unit ............................	80
• About mobile phone compatible with Phone Book Access Profile
(PBAP) ............................................................................................	80
Using Bluetooth audio player .................................................	81
Bluetooth device settings ......................................................	82
Rear View Camera Operations...........	83
Using a rear view camera .......................................................	83
• Activating the rear view camera .....................................................	83
• Displaying the picture from the rear view camera...........................	83
References...........................................	84
Maintenance .........................................................................	84
Troubleshooting/error messages ............................................	85
Specifications........................................................................	91

ENGLISH

7

ENGLISH

Introduction

Parts identification

Screen (touch panel)

1 Loading slot

20 (Eject) button

Ejects the disc.

3AV MAP/DISP OFF button

•Switches the screen between the map screen and AV screen. ( page 12)

•Turns off/on the screen. [Hold] ( page 10)

4SRC/button

•Selects the source. ( page 44)

•Turns off/on the AV function. [Hold] ( page 44)

Monitor panel

5Volume adjustment knob

Adjusts the audio volume.

•About the adjustable volume range, page 69 (<Amplifier Gain>).

•To adjust the guidance volume, page 29.

Decrease

Increase

6 AUX input terminal

7 USBinput terminal

8 (Detach) button

Detaches the monitor panel. ( page 4)

You can change the color of the buttons on the monitor panel. ( page 67)

8

Installation settings

When you turn on the unit for the first time, the initial	4 Adjust the settings.
setup screen appears.
1 Turn on the ignition switch.
The power is turned on, and the startup screen is
displayed for about 5 seconds.

2Select the language you want for the display and the voice guidance.

•You can also select the system language through the AV menu (<Settings> - <System> - <Language>, page 71)

3 Display installation settings screen.

State/	Select the State or Province where
Province	you are now.
Time Zone*	Select your residential area for
	automatic clock adjustment by
	GPS signal.
DST*	Select <Auto> if your residential
	area is subject to Daylight Saving
	Time.
Reverse	Select the reverse signal polarity
Signal	(<Battery> or <GND>)
Polarity*	according to the connection of
	your car.
Camera	Select <On> when connecting
Input*	the rear view camera to the
	CAMERA IN jack.

•If you select [Skip Installation Settings (for Store Display)], the System starts in the store

display mode.	5
You need to make the installation settings next
time you turn on the power.
– When you turn on the power, <Select
Language> appears. After selecting
the language, the confirmation message
appears. Press [Yes] so that the System starts
initialization. When initialization is complete,
<Select Language> ( Step 2 above) is	6
displayed.

*You can also change these settings through the AV menu (<Settings>, page 71).

ENGLISH

9

ENGLISH

Basic operations

Turning on the power		Turning off/on the screen

Turn on the ignition switch.

Startup screen appears for about 5 seconds.

• You can change the startup screen. ( page 71)

[Hold]

•When displaying the map screen for the first time after turning on the power, the screen below appears. Press [OK] to use the map screen.

•The power is turned off when the ignition switch is turned off.

Messages about the status of

GPS signal reception

Current status of the GPS signal reception

“Check GPS	Check the connection of the GPS
Antenna”	antenna.
“Acquiring	• Acquiring GPS signals. Wait until
GPS Signal”	signal reception is completed.
	• GPS signals cannot be received. Move
	to the place where the System receives
	the GPS signals.

The screen is turned on.

•You can erase the clock display while the screen is turned off. (<Clock on Video/Screen-Off>, page 70)

10

Operations on the touch panel

When items on the menu are not available

Non-available items will be shaded

Basic operations

To select folder/track on the list

Select a folder (1), then a track (2).

Current folder

Current track

	To change the page of menu/list		Scrolling the track/song information
Menu		When all the text is not shown at once...
	Current page/total menu pages

Characters you can use

ENGLISH

Changes the page

List

Ex.: Folder/track list

Changes the page

Skips the list up or down

11

ENGLISH

Switching screens

Map screen

The AV control bar is displayed on the map screen. You can perform AV source operations using the AV control bar.

• Pressing also displays the AV control bar. In this case, the AV control bar disappears automatically after 5 seconds.

Erases the AV control bar

• You can change the source by pressing while the AV control bar is displayed.

While driving at a speed greater than 6 mi (10 km/h), some screens on the navigation menus are not available.

•Press [] to return to the previous screen.

•On navigation screens only: press [] to display the current position on the map.

•On <Settings> on <AV Menu> only: press [] to display the current source screen.

12

Navi Menu

Shows the destination menu and information about the navigation system.

Only for KW-NT3HDT

Switching screens

AV screen

AV Menu

Changes or turns off the AV source.

Options	Settings
Changes the navigation settings. ( page 40)	Changes the detailed settings. ( page 68)

Only for KW-NT3HDT

ENGLISH

13

ENGLISH

Navigation System

Safety instructions/information for the Navigation System

SAFETY INSTRUCTIONS

Use of the Navigation System is only permitted if the traffic conditions are suitable and you are absolutely sure that no risk, obstruction or inconvenience will be incurred to you, your passengers or other road users.

The requirements of the Road Traffic Regulations must always be followed. The destination must not be entered while driving the car.

The Navigation System serves solely as an aid to navigation. It never releases the drivers from their duties to drive carefully and to make own judgement in road traffic. Inaccurate or incorrect instructions may happen to be given due to changing traffic

conditions. The actual road signs and traffic regulations must therefore always be observed. In particular,

the Navigation System cannot be used as an aid to orientation when visibility is poor.

This Navigation System must only be used for its intended purpose. The volume of the car radio/ Navigation System must be adjusted so that external noise is still audible.

Navigation guidance is performed, based on the database, therefore, it may not be applicable to the current situation because of changes in traffic

conditions (e.g. changes in tollroads, principal roads, one-way traffic, or other traffic regulations). In this case, observe the current traffic signs or regulations.

•Traffic signs should be observed carefully while driving using the Navigation System. Navigation System is only an aid. Driver must always decide whether or not to heed the information provided.

JVC does not accept liability for erroneous data provided by the Navigation System.

•Traffic guidance is restricted to passenger vehicles only. Special driving recommendations and regulations for other vehicles (e.g. commercial vehicles) are not included.

•Do not operate the unit while driving.

Terms of licence

You are granted a non-exclusive licence to use the database for your personal purposes. The present licence does not authorise the granting of sublicenses. Use of the data is only permitted in this specific JVC system. It is forbidden to extract or make further use of significant parts of the database content, or to duplicate, modify, adapt, translate, analyse, decompile or reverse-engineer any part thereof.

WARNING:

Road traffic regulations always take priority when a vehicle is being driven in traffic. Navigation System is only an aid. Errors may occur in individual data items/ entries. At all times, the driver must decide whether or not to heed the information provided.

JVC does not accept liability for erroneous data provided by the Navigation System.

© 2009 NAVTEQ All rights reserved.

Information/icons on the map

•The information on the map (such as street name, the POI information, and speed limit) may not be always displayed (for example, if the System does not have the information of the position).

•Home () and favorite point () icons are displayed after home/favorite points are registered.

•POI icons are displayed on the map depending on the <POI Icon> setting ( page 15) and the map scale is between 80 ft (25 m) and 800 ft (250 m).

–The following icons are displayed when the map scale is between 80 ft (25 m) and 0.6 mi (1 km):

–Airport icon in the travel category

–Golf course icon in the leisure category

–Gas station icons

•POI icons may not be displayed correctly when the System displays the wide area of map. In this case, zoom in the map to display the detailed map.

14

Basic operations

About the current position screen

Favorite points ( pages 17 and 34) Your position

POI (Point Of Interest) ( “List of POI icons”, page 43)

Home ( pages 17 and 34)

Traffic information
(only for KW-NT3HDT)
( page 35)
Shows <Navi Menu> ( page 13)	Current street

Current time

Direction

Scale

Zoom buttons

( below)

Shows the AV control bar ( page 12)

Speed limit on the current street

To display/hide POI icons on the map	To change the map scale
1 On <Navi Menu>:	1 Display the zoom buttons and scale buttons.

ENGLISH

2Select categories (1) and sub-categories (2) of POI which you want to be displayed on the map.

• When the AV control bar is displayed, the zoom buttons are not shown. Erase the AV control bar by pressing the source icon on the bar. ( page 12)

[Select All]: Selects all sub-categories [Deselect All]: Deselects all sub-categories.

• The selected items are marked with “ .”

3Activate or deactivate the POI icons of the selected categories.

Displays the selected POI icons

Deactivates

2

Zoom in

You can also select a scale directly by pressing one of the scale buttons.

Zoom out

15

ENGLISH

Basic operations

To scroll the map		To display your current
		position

The position you touched is centered on the map.

Direction and distance from your current position

•Touch and hold the map to keep scrolling the map.

•The scrolling speed varies depending on the position you are touching and holding:

–Inner area: slow

–Outer area: fast

To display the current position

To change the map view

3D Map

The three dimensional map is displayed in “heading up.”

• The icon shows the direction of north.

2D North Up

The map view is oriented with north “upwards,” as in usual paper maps.

• The icon shows the direction of the car.

2D Heading Up

The map rotates so that you are always displayed heading “upwards.”

•The icon shows the direction of north.

•You can also change the map view through the navigation menu (<Options> - <Display> - <View Mode>, page 41).

16

Registering your home/favorite points

You can register one point as your home or 100 favorite	4
points.

1Scroll the map to select the position you want to select as a destination.

•To search the destination using <Destination Menu>, pages 19 to 27.

2

•If there are several POIs on the selected position, select one from the list.

–The list appears only when <POI Icon> is set to <On>. ( page 15)

[Save as Home]:

The selected position is saved as home and the home is marked withicon on the map.

•When the home is already registered, you are asked if you want to replace the old home. Press [Yes] to replace, or press [No] to cancel.

[Save as Favorite]:

The selected position is saved as a favorite point and the favorite point is marked withicon on the map.

• To edit the registration, page 34.

POIs

3

ENGLISH

17

ENGLISH

Searching for a place

Setting a destination by scrolling the map

1Scroll the map to select the position you want to select as a destination. ( page 16)

2

•If there are several POIs on the selected position, select one from the list.

–The list appears only when <POI Icon> is set to <On>. ( page 15)

The search result is displayed.

Guidance starts.

•To cancel guidance, page 29.

•To set the selected position as via point, page 28.

•To change route options, page 29.

•For details about the search result screen, right.

About the search result screen

Zoom buttons

•You can change the map scale by pressing the zoom buttons.

•You can display the map of selected area on whole screen by touching the map part once. (If you press more than once, the map scrolls.) To display the information screen again, press [Select].

•The information screen is always displayed with the 2D North Up map view regardless of the current map view setting. ( page 16)

18

Searching for a place

Setting a destination using the <Destination Menu>

	1		Home*	Goes to your home.
				• To register your home, page 17.
			Previous*	Searches from the history of previous
				destinations and via points.
				• You can select a place from the last
				50 destinations and via points.
				• To delete the history, page 39.
	2		Favorites*	Searches from your favorite points.
				• To register your favorite points,
				page 17.
				• To edit the information about the
				favorite points, page 34.
			Assistant	Searches from the list of POIs (Point Of
			POIs	Interest) saved on the SD card using
				Street Director Assistant. ( page 25)
	3	Select a method to search for a destination.	Address	Searches by an address. ( page 21)
			Phone	Searches by a telephone number.
				( page 22)
			POI Name	Searches from the database of POI.
				( page 23)
			Vicinity	Searches for POIs (Point Of Interest)
				around your current position, the
				position selected on the map, the
				destination, or the route you are taking.
				( page 24)
			Coordinates	Searches by coordinates of the
				destination. ( page 25)
			Quick	Searches for POIs of a registered
			Search	category — [Quick Search 1]/[Quick
				Search 2]/[Gas Station] (Initial). (
				page 26)
			* Selectable only when at least one place is registered.

ENGLISH

19

ENGLISH

Searching for a place

About search screens and input screens

Read through the following instructions for using search screens and input screens before using <Destination

Menu>.

To enter names, addresses, or numbers

Number of matches

•When there are more than 100 matches, “100+” is displayed and only first 100 matches are displayed.

Hold: Adds “+”

Displays the list of matches Selects 1st candidate ( “List of matches” on

the right)

State/Province selecting screen

You can change the State/Province if the selecting button appears on the screen.

Enters a space

Press: Deletes last character

Hold: Deletes all characters

Displays other keyboards

•For available characters, page 11.

•Buttons vary depending on the input item.

•Non-available items will be shaded on the menu screen.

•For some input screens, available characters are automatically narrowed down as the System searches its database for matches.

•Lower cases are not available.

List of matches

When you press [List] on the input screen, the list of matches appears. Select desired item from the list.

•When the number of matches is 5 or less, the list of matches automatically appears.

20

	Searching for a place
By address <Address>
1	3 Enter the street name, then select from the
	list ( page 20).
	Selects the center of the city (Then, go to step 5.)

2Enter the city name, then select from the list

( page 20).

Changes State or Province

Specifies the zip code ( “To specify the zip code” below)

4 Enter the house number, then select from the list ( page 20).

• If no data of house number for the selected street is available in the database, select [Middle of the Road] or [Intersection].

To specify the zip code

Changes country

ENGLISH

Returns to the city input screen

Continued on the next page

21

ENGLISH

Searching for a place

To select the center of the street or intersection on the street

Specifies the crossing street to select intersection on the street

Selects the center of the street

5

Guidance starts.

•To cancel guidance, page 29.

•To set the selected position as via point, page 28.

•To change route options, page 29.

•For details about the search result screen,page 18.

By telephone number

<Phone>

1

2Enter the telephone number, then select from the list ( page 20).

Changes country

The search result is displayed.

Guidance starts.

•To cancel guidance, page 29.

•To set the selected position as via point, page 28.

•To change route options, page 29.

•For details about the search result screen,page 18.

22

From the list of POI <POI Name>

1

2Enter the POI name, then select from the list

( page 20).

Changes State or Province

Specifies the category and sub-category ( “To specify the category and sub-category” below)

To specify the category and sub-category

Cancels the selected category

Selects all sub-categories

Sub-categories

Searching for a place

Lists from the nearest Lists in alphabetical order

The System displays up to 100 POIs.

The search result is displayed.

Guidance starts.

•To cancel guidance, page 29.

•To set the selected position as via point, page 28.

•To change route options, page 29.

•For details about the search result screen,page 18.

ENGLISH

23

ENGLISH

Searching for a place

POI near a place/route <Vicinity>

The System has a huge database of POIs (Point Of Interest), such as restaurants, gas stations, hospitals, etc.

You can search for a POI around the place where you are now. While guided, you can also search for a POI near the destination or along the route.

1

3Select a category (1), then a sub-category (2) for the POI.

Selects all sub-categories

Sub-categories

2 Select the area to search.

“Searching...”

4 Select a POI from the list.

Local	Within 12.5 mi (20 km) of your
	current position or the position
	selected on the map. If no POI
	is found in this area, the System
	expands the area to search.

Dest. Within 12.5 mi (20 km) of the destination. If no POI is found in this area, the System expands the area to search.

On Route • On freeway: 180 mi (300 km) along the route you are taking.

•Others: 15 mi (25 km) along the route you are taking.

• The System displays up to 50 POIs.

The search result is displayed.

Guidance starts.

•To cancel guidance, page 29.

•To set the selected position as via point, page 28.

•To change route options, page 29.

•For details about the search result screen,page 18.

24

By coordinates

<Coordinates>

1

2 Enter the latitude and the longitude.

Searching for a place

From the list of POIs imported by yourself <Assistant POIs>

Importing POI information on Google Maps

You can import POI information on Google Maps through an SD card.

For details about Street Director Assistant, visit <http:// www.jvc.co.jp/english/car/> (English website only).

•When the SD card is ejected, the imported POI cannot be used.

ENGLISH

The search result is displayed.

Guidance starts.

•To cancel guidance, page 29.

•To set the selected position as via point, page 28.

•To change route options, page 29.

•For details about the search result screen,page 18.

1

2

Lists from the nearest Lists in alphabetical order

The search result is displayed.

Guidance starts.

•To cancel guidance, page 29.

•To set the selected position as via point, page 28.

•To change route options, page 29.

•For details about the search result screen,page 18.

25

ENGLISH

Searching for a place

Quick Search

You have three [Quick Search] buttons in <Destination Menu>. You can assign a POI category to each button. When you press one of the buttons, the System searches for a POI of the registered category.

•[Gas Station] is registered to one of the three buttons when shipped from the factory. You can also change the registered category of this button.

To register a category to the buttons

1Select one of the [Quick Search] buttons to register the category.

2Select a category (1), then a sub-category (2) of the POI.

Selects all sub-categories

Sub-categories

The search for the selected category starts to register it to the [Quick Search] button.

3	Registered category

4Repeat steps 1 to 3 until three categories are registered.

The selected category (or sub-category) name is assigned to the button.

•The selected category is registered to the [Quick Search] button even if you cancel the searching before the search is completed.

26

To change a category assigned to the [Quick Search] button

1Select one of the [Quick Search] buttons whose category you want to change.

Searching for a place

To use Quick Search

1

“Searching...”

2 Select a POI from the list.

ENGLISH

or

2Perform steps 2 and 3 of “To register a category to the buttons” ( page 26).

• The System displays up to 50 search results.

The search result is displayed.

Guidance starts.

•To cancel guidance, page 29.

•To set the selected position as via point, page 28.

•To change route options, page 29.

•For details about the search result screen,page 18.

27

ENGLISH

How you are guided

Starting guidance to the destination or via point

1	Select a destination or via point. ( pages 18	The System starts calculating the route to the selected
	to 27)
2	To set as destination	destination, and guidance starts.

Cancels the calculation

To change the destination

To cancel guidance, page 29.

To set as via point

You can add the via points only after selecting your destination.

Destination

Via point

•You can select up to four via points.

•For editing your route, page 32.

28

		How you are guided
Changing route options		Canceling guidance
1 On the search result screen:	1

2

2 Set options.

A confirmation message appears.

ENGLISH

Priority	Select the priority for route
	calculation ([Fastest]: fastest
	route/[Shortest]: shortest
	route).
Freeway	Select whether to use ([Use]) or
Toll Road	avoid ([Avoid]) these types of
Ferry	options to go to the destination.
Bypass Traffic	Select the route calculation
(Only for KW-	method with traffic information.
NT3HDT)	( page 35)

•You can also change these settings through the navigation menu (<Options> - <Route>,page 40).

•The settings are effective next time the System calculates a route.

3

Adjusting the volume of the voice guidance

•About the adjustable volume range, page 69 (<Amplifier Gain>).

•You can also adjust the volume through the navigation menu (<Guidance Volume>,page 40).

29

ENGLISH

How you are guided

About route guidance screen

Distance to the next turn						Lanes to take
• Press to listen to the last voice guidance again.				Next street		(Appears when coming within 3 mi (5 km) of it.)
Next turn to make
The second turn to make								Route to take
(if any)								Shows AV control
								bar

Direction and distance to the destination () or a via point ()

•Press to switch the information between the final destination and the nearest via point.

Current street

Speed limit on the current street

: Estimated time of arrival (ETA)

: Remaining time to the selected destination or a via point

•Press to switch the information between estimated time of arrival (ETA) and remaining time.

Guidance at turns

When you approach a turn, the System guides you with voice guidance and indications on the screen.

• Guidance voice comes out only through the front speakers (and the F OUT jacks on the rear).

			To remove the magnified map, touch the map part
			on the right side of the screen.
			What if I miss a turn?
			Don’t worry. The System calculates a new route
			quickly.
	Magnified map

•You can select whether or not to display the magnified map through the navigation menu (<Options> - <Display> - <Magnified View>, page 41).

•When you reach the area approximately within 120 ft (40 m) around the destination/via point, the Navigation System considers you to have reached your destination/via point.

30