Jotul GI 425 DV User Manual

Size:
2.22 Mb
Download

Jøtul GI 425 DV

Camden Classic

Direct Vent Gas

Fireplace Insert

Installation and Operation Instructions

WARNING:

IF THE INFORMATION IN THESE INSTRUCTIONS ARE NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

FOR YOUR SAFETY:

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

INSTALLATION:

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER, SERVICE AGENCY OR LICENSED GAS SUPPLIER.

WHAT TO DO IF YOU SMELL GAS:

DO NOT TRY TO LIGHT ANY APPLIANCE.

DO NOT TOUCH ANY ELECTRICAL SWITCHES.

DO NOT USE THE PHONE IN YOUR BUILDING. IMMEDIATELY CALL YOUR GAS SUPPLIER FROM A NEIGHBOR’S PHONE.

FOLLOW YOUR GAS SUPPLIER’S INSTRUCTIONS.

IF YOU CANNOT REACH YOUR GAS SUPPLIER, CALL THE FIRE DEPARTMENT.

AVERTISSEMENT:

ASSUREZ-VOUSDE BIEN SUIVRE LES INSTRUCTIONS DANS CETTE NOTICE POUR REDUIRE AU MINIMUM LE RISQUE D’INCENDIE OU POUR EVITER TOUT DOMMAGE MATERIEL, TOUTE BLESSURE OU MORTALIT’E.

NE PAS ENTREPOSER NI UTILISER D’ESSENCE NI OU LIQUIDES INFLAMMABLES DANS LE VOISINAGE DE CET APPAREIL OU DE TOUT AUTRE APPAREIL.

L’INSTALLATION LE SERVICE DOIVENT ETRE EXECUTES PAR UN INSTALLATEUR QUALIFIE, AGENCE DE SERVICE OU LE FOURNISSEUR DE GAZ.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ.

NE PAS TENTER D’ALLUMER L’APPAREIL

NE TOUCHEZ A AUCUM NTERRUPTEUR.

NE PAS VOUS SERVIR DES TELEPHONES

SE TROUVANT DANS LE BATIMENT OU VOUS VOUS TROUVEZ.

APPELEZ IMMEDIATEMENT VOTRE FOURNISSEUR DE GAZ CHEZ UN VOISIN. SUIVEZ LES INSTRUCTIONS DU FOURNISSEUR.

SI VOUS NE POUVEZ REJOINDRE LE FOURNISSEUR DE GAZ, APPELEZ LE SERVICE DES INCENDIES.

Welcome to Jøtul...

Congratulations on the purchase of your new

Jøtul GI 425 DV Camden Classic Gas Fireplace.

We at Jøtul are glad you’ve made the decision to warm your hearth with one of our products. We’ve been making fine quality cast iron stoves and fireplaces continuously since 1853. Your new Camden fireplace is the result of our experience as the world’s largest manufacturer of solid fuel burning appliances for over 150 years.

In the GI 425 DV Camden Classic, we’ve combined advanced gas technology with the warm, traditional elements of cast iron. With proper care and use, your Jøtul fireplace will provide you with many years of safe, dependable and satisfying service.

The GI 425 DV Camden Classic is a direct vented gas heater designed and approved for installation into an existing masonry fireplace. Please take a few minutes to familiarize yourself with this manual and the features of your new gas fireplace.

PLEASE READ THESE INSTRUCTIONS IN THEIR

ENTIRETY AND MAKE THEM AVAILABLE TO

ANYONE USING OR SERVICING THIS

APPLIANCE.

THIS PRODUCT MUST BE INSTALLED BY A

LICENSED MASTER OR JOURNEYMAN PLUMBER

OR GAS-FITTERWHEN INSTALLED IN THE

COMMONWEALTH OF MASSACHUSETTS.

2

Table of Contents

Specifications .............................

4

Installation & Service Tools ..........

4

General Information ...................

5

Safety Information..........................

6

Installation

 

Fireplace Requirements ............

4

Clearances .......................................

8

Hearth Protection .........................

9

Vent Requirements .....................

10

Masonry Fireplace .......................

11

Prefabricated Fire ........................

12

Fireplace Assembly

 

Gas Connection ............................

14

Gas Pressure..................................

14

High Altitude Adjustment ........

15

Fuel Conversion ............................

16

Wall Thermostat ..........................

18

Remote Control ............................

18

Antique Brick Kit ..........................

19

Log Set Installation .....................

20

Surround Assembly .....................

21

System Check................................

22

Operation

 

Burner Controls ...........................

24

Blower............................................

25

Maintenance

 

Annual Cleaning .........................

26

Glass Replacement .....................

26

Illustrated Part Breakdown ......

28

Replacement Parts List .............

29

Service Log ................................

30

Lighting Instructions ................

31

Unpacking the Fireplace

1.Before you remove the carton, remove the cast iron parts that are packed around the fireplace firebox.

2.Lift the shipping carton off of the fireplace cabinet.

3.Unpack the Firebox. The Logset is packaged inside the firebox. Remove the Glass Panel Frame to unpack the firebox:

Locate the right and left spring latches on the underside of the firebox floor. Release each latch by pulling them forward to disengage the Frame from the Firebox body.

Pull the Glass Frame away from the Firebox and lift to disengage it from the three steel retainer tabs located at the top of the firebox. Set the glass out of the way.

Do not unpack the log parts until you are ready to install them.

4.Install the Levelling Bolts. Five round head carriage bolts are included in the Hardware Bag. Tilt the insert cabinet back on the pallet to allow clearance for installation of these bolts into the Cabinet Base, one at each corner and one in the center.

Spring Latch

Pull each Spring Latch to disengage them from the Glass Frame.

3

Jøtul GI 425 Camden

Direct Vent Gas Fireplace

Manufactured and Distributed by:

Jøtul A.S.A.

Fredrikstad, Norway

Jøtul North America

Gorham, Maine

MEA No. 369-04-E

Test Standards

This appliance complies with National Safety standards and is tested and listed by Intertek Testing Services of Middleton, Wisconsin.

In addition, the Jøtul GI 425 DV gas fireplace insert has been tested and listed as a direct vent gas fireplace heater and listed to ANSI Z21.88-1998(NFPA 54) and CSA2.33-M98for Canada.

Specifications

Input Rates

Natural Gas

26,000 BTU/hr. maximum input

13,000 BTU/hr. minimum input

Propane

26,000 BTU/hr. maximum input

13,000 BTU/hr. minimum input

Inlet Pressure:

MIN

MAX

Natural Gas:

5.0 WC (1.24 kPa)

7.0 WC (1.74 kPa)

Propane:

12.0 WC

(2.98 kPa)

14.0 WC (3.48 kPa)

Manifold Pressure:

 

MIN

MAX

 

 

 

 

 

Natural Gas:

1.2 WC (0.29 kPa)

3.8 WC (0.95 kPa)

Propane:

2.9 WC (0.72 kPa)

11.0 WC (2.74 kPa)

Steady State Efficiency: 77.3%

A.F.U.E. Efficiency: 67.9%

Piezo Ignitor / Standing Pilot

THIS FIREPLACE IS SHIPPED AS A NATURAL GAS FIREPLACE ONLY. IF USE WITH PROPANE IS DESIRED, THE FIREPLACE MUST BE CONVERTED TO USE WITH PROPANE. FOR YOUR CONVENIENCE THIS FIREPLACE IS SHIPPED WITH A PROPANE CONVERSION KIT.

Accessories

Antique Brick Panel Kit .......................................

#155311

Wide Surround Kit - Cast Iron

Max. Opening Overlap: 47” Wide x 33 1/2” High.

Matte Black ...................................................

#155323

Blue Black Enamel .......................................

#155324

Jøtul Iron Gray ..............................................

#155354

Fuel Conversion Kit - NG to LP .........................

#155300

Fuel Conversion Kit - LP to NG .........................

#155303

Wall Thermostat ...................................................

#750003

Remote Control .....................................................

#129706

Jøtul QuickFace™ System

Rectangular Frame w/ Screen,

 

Brushed Stainless Steel .............................

#155312

Arched Frame w/ Screen,

 

Brushed Stainless Steel .............................

#155313

Rectangular Frame w/ Screen,

 

Matte Black ...................................................

#155314

Arched Frame w/ Screen,

 

Matte Black ...................................................

#155315

Double Doors, Cast Iron -

 

Matte Black ...................................................

#350565

Double Doors, Cast Iron -

 

Blue Black Enamel .......................................

#350566

Suggested Tools for

Installation and Service

External regulator (for Propane only)

Piping which complies with local code

Manual shutoff valve - T-Handlein Massachusetts

Sediment trap - if required by code

Tee joint

Pipe wrench

Pipe sealant

10mm open end wrench

1/2”, 7/16” open end wrench

Phillips head screwdriver

Flat head screwdriver

1/4” nut driver

Gloves

Safety glasses

Torx T20 screwdriver

Leak test solution

Power Drill

4

General Information

IMPORTANT:

SAVE THESE INSTRUCTIONS.

THIS HEATER MUST BE INSTALLED AND MAINTAINED BY A QUALIFIED SERVICE AGENCY.

DO NOT ATTEMPT TO ALTER OR MODIFY THE CONSTRUCTION OF THIS APPLIANCE OR ITS COMPONENTS. ANY MODIFICATION OR ALTERATION WILL VOID THE WARRANTY, CERTIFICATION AND LISTING OF THIS APPLIANCE.

1.The installation and repair of this appliance must be done by a qualified service person. Failure to properly install and maintain this heater could result in an unsafe or hazardous installation, which may result in a fire, explosion, property damage, personal injury or loss of life.

2.This appliance should be inspected before use and at least annually. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is imperative that control compartments, burners and circulating air passageways of the appliance be kept clean.

`S’assurer que le bruleur et le compartiment des commandes sont propres. Voir les instructions d’installation et d’utilisation qui accompagnent l’appareil.

3.The installation must conform to local codes. Your local Jøtul authorized dealer can assist you in determining what is required in your area for a safe and legal installation. Some areas require a permit to install a gas burning appliance. Always consult your local building inspector or authority having jurisdiction to determine what regulations apply in your area.

In the absence of local codes, the installation requirements must comply with the current National codes. In the U.S., these requirements are established in the National Fuel Code, ANSI Z223.1.(NFPA 54). In Canada, the codes have been established in CAN/CGA B149 Fuel Installation

Code.

Installer l’appareil selon les codes ou reglements locaux, ou, en l’absence de tels reglements, selon les Codes d’installation CAN/CGA-B149.

4.DO NOT OPERATE THIS FIREPLACE IF ANY PART HAS BEEN UNDER WATER.

Immediately call a qualified service technician to inspect the heater and to replace any part of the control system and any gas control which has been under water.

Ne pas se servir de cet appareil s’il a ete’ plonge dans l’eau, completement ou en partie. Appeler un technicien qualifie pour inspecter l’appareil et remplacer toute partie du syste’me de controle et toute commande qui ont ete plonges dans l’eau.

5.Do not operate the fireplace with the glass front removed, cracked or broken. Replacement of the glass should be done by a licensed or qualified service person. Only remove glass for routine service. Always handle glass carefully.

Pour utilisation avec les portes en verre cerifiers aved l’appareil seulemend ou. Ne pas utiliser avec des portes on verre.

6.Notify your insurance company before proceding with installation of this fireplace.

5

Safety Information

Due to the high operating temperatures this appliance should be located out of traffic and away from furniture, draperies, etc. Maintain proper clearance to combustible mantels and fireplace trim.

Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition.

Young children should be supervised while they are in the same room as the GI425 gas fireplace.

Surveiller les enfants. Garder les vetements, les meubles, l’essence ou autres liquides a vapeur inflammables loin de l’appareil.

Clothing or other flammable materials should not be placed ON or NEAR the GI425 gas fireplace.

Never allow any to use the fireplace if they are unfamiliar with its operation.

NEVER store or use gasoline or any other flammable vapors or liquids in the vicinity of the GI425 gas fireplace.

Never burn any solid materials (wood, cardboard, paper, coal, etc.) in this gas fireplace. Use with natural gas or propane fuel ONLY.

Any safety screen, glass or guard removed for servicing the appliance must be replaced prior to operating the appliance.

Do not slam or strike the glass panel.

Were gloves and safety glases while performing maintenance procedures.

Electrical Hazard

Be aware of electrical wiring locations when cutting holes in walls and ceilings for termination.

The GI425 Blower must be electrically grounded in accordance with local codes or, in the absence of local codes, with the current ANSI/NFPA 70, National Electrical Code or CSA C22.1-CanadianElectrical Code.

The GI425 Blower is supplied with a three-prong(grounding) plug for protection against shock hazard and should be plugged directly into a properly groundedthree-prongreceptacle. DO NOT CUT OR REMOVE THE GROUNDING PRONG FROM THE PLUG.

Always disconect the power supply when per-

6

forming routine service on the fireplace.

 

Installation

Requirements

The GI425 DV Camden Gas Insert can be installed in most solid fuel burning fireplaces of either masonry construction or a prefabricated factory built fireplace.

Prior to any installation of the GI425 DV Camden the existing chimney exhaust flue must be thoroughly cleaned and completely inspected by a qualified chimney sweep or fireplace service person.

Do not install this insert into a chimney that is damaged. Any repairs must be made prior to installing the insert. If you are unsure of the condition of your fireplace and chimney, contact a professional fireplace technician or your local authorized Jøtul dealer for professional assistance.

DO NOT REMOVE BRICKS OR MORTAR FROM THE FIREPLACE OR CHIMNEY STRUCTURE. However, masonry or steel may be removed from the smoke shelf and adjacent damper frame area to accommodate installation of a chimney liner, provided that their removal will not weaken the structure of the fireplace or chimney, and will not reduce protection for combustible materials.

If the fireplace has been modified to accommodate installation, use anchors or masonry nails to attach the metal Fireplace Conversion Notice Plate to the back wall of the masonry fireplace firebox where it will be readily seen should the insert be removed.

THIS APPLIANCE MUST NOT BE CONNECTED TO A CHIMNEY OR FLUE SERVING ANY OTHER APPLIANCE OF ANY KIND.

All venting components must be installed in accordance with the terms of their listing and manufacturer’s instructions. Refer to the pipe manufacturer’s instructions for proper pipe clearances.

This fireplace insert is specifically designed for use with 3” Type B vent pipe components or a Listed Flexible gas liner.

Do not modify or alter the construction of the gas insert or any of its components to enable it to fit into a fireplace. Any modification of the insert will void the warranty, certifications and approvals of the unit and could be dangerous.

 

25”

 

 

 

 

 

635 mm

 

 

 

 

 

20”

 

 

 

 

 

508 mm

 

 

 

 

 

Air

11”

13”

 

 

7 1/2”

Intake

 

 

Exhaust

289 mm

330mm

 

 

191 mm

Outlet

 

 

 

 

 

 

11/2”

81/2” (216mm)

 

 

 

 

38mm

 

 

 

 

 

 

 

 

2”

 

 

 

Exhaust

 

50 mm

 

 

 

Outlet

 

 

 

 

 

30 1/4”

Air

22”

 

 

 

768 mm

 

 

 

Intake

 

 

 

 

 

559 mm

 

 

 

 

 

17”

 

 

 

 

 

432 mm

 

 

 

5”

 

 

 

 

 

127 mm

 

 

 

40”

 

21 1/2”

 

 

 

1016 mm

 

 

 

 

 

546 mm

 

 

 

 

 

 

 

Figure 1. GI 425 DV dimensions.

Minimum Fireplace Requirements

The GI425 DV CAMDEN gas insert has been specifically designed to be installed into a solid fuel burning factory built fireplace OR a code approved solid fuel burning masonry fireplace with a tile flue liner. An acceptable fireplace cavity must have the minimum dimensions specified below.

D B

E C

A

A:Opening Width = 28” (711 mm)

B:Opening Height = 22” (559 mm)

C:Back Wall Width = 20” (508 mm)

D:Back Wall Height = 20” (508 mm)

E:Depth = 13” (330 mm)

Figure 2. Minimum fireplace cavity dimensions.

 

22”

Surround

559 mm

Hangers

Min.

 

Opening

 

Height

28”

 

711 mm

 

Min. Opening Width

 

for Surround Hanger Clearance

 

Figure 3. Minimum opening clearance. Optional Lattice Surround shown.

7

Covering the Fireplace Opening

Two cast iron surround styles are available for the GI 425 Camden fireplace insert.

Standard Classic Surround

The GI425 Camden includes Surround Panels that will overlap a maximum fireplace opening

39” Wide x 29 1/2” High.

The actual standard surround dimensions are 40”Wide x 30 1/4” High.

Optional Lattice Classic Surround

The Lattice Surround Kit shares the same dimensions as the standard Classic Surround described above. #350557 - Matte Black

#350558 - Blue Black.

#350559 - Jøtul Iron

Optional Wide Surround

#155323 - Matte Black

#155324 - Blue Black.

#155354 - Jøtul Iron

These optional panels can be used to extend the Classic or Lattice surround panels to cover oversize fireplace openings up to a maximum 47” Wide x 33 1/2” High.

The actual wide surround dimensions are 48” Wide x 34” High.

NOTE: The additional weight of the Wide Surround may necessitate use of the Anchor Bracket which is included with this fireplace. The anchor will ensure that the surround assembly aligns properly against the fireplace face. Use the installation instructions included in the Hardware bag.

48” 1219 mm

34” 864 mm

Figure 4. Wide Surround Dimensions.

SEE PAGE 21 FOR SURROUND PANEL

ASSEMBLY INSTRUCTIONS.

Clearance Requirements

The following clearances and hearth requirements are the minimum requirements when installing the Camden gas insert into a solid fuel burning appliance. These dimensions are measured from the firebox cabinet to the combustible material. See figures 5 and 6.

A combustible surface is anything that can burn (i.e. sheet rock, wallpaper, wood, fabrics etc.). These surfaces are not limited to those that are visible and also include materials that are behind non-combustibles.

If you are not sure of the combustible nature of a material, consult your local fire officials. Remember, “Fire Resistant” materials are considered combustible: they are difficult to ignite, but will burn. Also,“fire-rated”sheet rock is consideredcombustible.

Always maintain the proper clearances to the appliance for the proper flow of ventilation air around the insert.

Figure 5. Clearance to Adjacent Combustible Material - measured from the fireplace centerline or hearth.

F

E

B

C

AD

A:Hearth Protection Width - None required

B:Hearth Protection Depth - None required

C:Side Trim Clearance, 1”thick (25 mm) = 21 3/4 in. (552 mm)

D:Side Room Wall Clearance = 39 3/4 in. (1010mm)

E:Top Trim Clearance = 39 1/2 in. (1003 mm)

F:Mantel Clearance at 9 in. max. depth = 47 in. (1194 mm) Mantel Clearance at 3.5 in. max. depth = 41 1/2 in. (1054 mm)

8

Mantel and Trim Clearance

 

 

9”

 

228 mm

 

 

8”

 

 

6 1/2”

 

 

5”

 

 

3 1/2”

 

 

UPPER

 

 

TRIM

27 1/2”

211/2”

1” Max.

Depth

736 mm

622mm

 

25 1/2”

191/2”

698 mm

508mm

23 1/2”

171/2”

660 mm

394mm

TOP OF FIREBOX

CABINET

22” 559 mm

Figure 6. Minimum Mantel Clearances. Measure clearances from the top and sides of the fireplace cabinet before installation of the cast iron surround panels.

Hearth Requirements

The Jøtul GI425 Camden does not require special hearth protection. Combustible flooring materials may be present directly in front of the fireplace insert.

9

Vent Guidelines

All vent components must be installed in accordance with the listing terms and manufacturer’s instructions.

Vent Height: Measured from the top of the insert to the top of the termination cap.

Minimum: no less than10'

Maximum: no greater than35'. See figures 9 and 10.

The minimum vent height above the roof or adjacent walls is specified by building codes. As a general guide, follow the Gas Vent Rule on page 12.

HORIZONTAL RUNS ARE NOT PERMITTED ANYWHERE IN THE VENTING SYSTEM.

Venting liners used on this appliance may not be less than 3” in diameter or greater than 3” in diameter.

Any unused flue or masonry enclosure can be used as a passageway for venting provided the flue is relined using 3” Listed flexible gas liner.

The remaining space around the liner in a masonry or zero-clearanceflue CANNOT be used to vent any other appliance.

Flexible liner components may not be exposed in any living space.

Installation of any components not manufactured or approved by Jøtul or failure to meet all clearance requirements will void all warranties and could result in property damage, bodily injury, or serious fire.

Never modify any venting component, or use any damaged venting product.

THE GAS APPLIANCE AND VENT SYSTEM MUST BE VENTED DIRECTLY TO THE OUTSIDE OF THE BUILDING, AND NEVER ATTACHED TO A CHIMNEY

SERVING A SOLID FUEL OR GAS BURNING APPLIANCE.

Variable Vent Restriction: See the System Check section on pages 22-23for specific instructions.

IMPORTANT NOTICE:

THE USE OF AN EXISTING CHIMNEY AS AN AIR INTAKE IS NOT COVERED UNDER THE ANSI Z21.88-1999-CSA2.33M99 TEST METHODS AND RESULTING ITS/WHI PRODUCT CERTIFICATION. THE CODE AUTHORITY HAVING JURISDICTION MUST BE CONSULTED PRIOR TO PROCEEDING WITH THIS INSTALLATION METHOD.

Masonry Fireplace Installation

When installing a GI425 DV Camden gas insert into a masonry fireplace the insert will be vented through dual 3” flexible gas aluminum liners.

This co-linearinstallation includes a pair of 3” flex ducts that run from the insert completely through the existing chimney to the termination cap.

One liner is attached to the Exhaust Outlet on the back of the unit and will carry the exhaust gases to the outside of the house. This exhaust liner must be directly connected to the unit and run the full length of the chimney. See figure 7.

The other 3” liner will be attached to the Air Intake Collar on the back of the unit to provide fresh air for combustion. The Intake Collar is labeled for easy identification. The liner must extend a minimum of 6’ off the back of the unit and extend through the damper area of the fireplace into the tile liner of the chimney. This liner can also extend the full length of the chimney and connect to the termination cap.

IMPORTANT

If the intake flex does not extend the full length of the chimney, forming a direct connection between the unit and the termination cap, A METAL BLOCK OFF PLATE MUST BE INSTALLED to seal the air intake from room air. Normally this sealing plate will be installed within the existing fireplace damper area. See figure 7. The sealing plate is not necessary if a direct connection is made between the cap and the fireplace.

WARNING! Avoid cross venting the insert. Before installation, label both ends of the exhaust flex pipe to ensure connection to the appropriate collars on the fireplace unit and vent termination cap.

CANADA REQUIREMENT: Both the Intake and the Exhaust liners must extend the full length of the chimney and be securely connected to both the unit and the termination kit.

If the fireplace has been modified to accommodate installation, use anchors or masonry nails to attach the metal Fireplace Conversion Notice Plate supplied with this unit to the back wall of the masonry fireplace firebox where it will be readily seen should the insert be removed.

10

Venting through a Masonry Fireplace

1.Measure height of the chimney to fireplace opening. Determine if both the intake and exhaust will be extended to the top of the chimney.

2.Use tin snips to cut the appropriate lengths of flex for both the intake and exhaust.

3.Attach the appropriate ends of the flex to the chimney termination kit.

4.Drop the liners down the chimney from the top and rest the termination kit atop the chimney.

5.Seal the chimney termination kit to the top of the chimney flue with high temperature sealant.

6.Secure the appropriate DIRECT VENT CAP to the termination kit.

7.Inside the fireplace, fully extend the flex liner pipe and cut off the excess so that the liners hang approximately 15” from the floor of the fireplace.

8.If the Air Intake pipe will not be attached to the chimney termination kit:(See NOTICE on page 10.)

a.It will be necessary to install a minimum length of 6 ft. flex pipe up into the flue.

b.A metal damper block off plate must be constructed and installed in the fireplace damper area to completely seal off the flue from the room. Cut holes in the plate for both the intake and exhaust flex pipes.

c.A direct vent cap is required to bring fresh air into the chimney flue and Air Intake flex pipe.

d.Compress the liners so that they are hanging out of the way above the fireplace opening.

e.Attach the Fireplace Conversion Notice to the back of the fireplace if appropriate.

9.Position the insert without surround panels halfway inside the fireplace and attach the liners to the appropriate ports on the rear of the stove. Be sure not to cross vent these connections. Secure the liners to the ports using sheet metal screws or hose clamps. No silicone or sealant is required.

WARNING:

FAILURE TO POSITION THE PARTS IN ACCORDANCE WITH THIS DIAGRAM OR FAILURE TO USE ONLY PARTS SPECIFICALLY APPROVED WITH THIS APPLIANCE MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY.

Listed Direct Vent

Termination Cap

Sealed Chimney

Cap Anchor Plate

Listed Flexible

Gas Liners

Max. Height 35 ft.

Min. Height 10ft.

Maintain proper clearance to Mantel and Trim

Metal block-offplate is required to seal flue from the living area if Air Intake pipe does not connect directly to a Direct Vent Termination at the top of the chimney

123456789

12345678 9

123456789

EXHAUST FLEX PIPE

AIR INTAKE FLEX PIPE

 

 

To Exhaust

 

 

Collar

Attach

Fireplace

 

Conversion Notice

To Air

Plate to Rear Wall

Intake

of Fireplaceif the

Collar

damper has been

modified.

 

Figure 7. Masonry Fireplace Venting Configuration.

11

Prefabricated Fireplace Installation

A factory-builtprefabricated fireplace will require a few modifications before installation of the Jøtul GI425 Camden fireplace insert.

Modification Steps:

1.Remove any fuel grate or other components attached attached to the firebox. On most models the firegrate is attached to the unit with brackets which should be cut or pried off.

2.Remove the damper assembly. This includes the damper blade, handle and any linkage. Two 3” liners must be able to pass through the damper area.

3.Remove any firescreen or door assembly. This is usually done by removing a support rod on the inside of the fireplace frame.

4.If there is a metal ashlip, it too should be removed to allow the unit to sit flat in the fireplace. Be sure to reinstall any screws removed.

IMPORTANT:

BEFORE STARTING THIS INSTALLATION, MAKE SURE THAT A GAS LINE CAN BE INSTALLED OR IS INSTALLED TO THE FIREBOX. THIS SHOULD ONLY BE DONE BY A QUALIFIED OR LICENSED PLUMBER OR GAS FITTER.

The GI425 DV Camden gas insert is specifically designed to be vented using a co-linearsystem.

Installation includes a pair of 3” flex ducts that run from the insert completely through the existing chimney to the termination cap. See figure 8.

One liner is attached to the exhaust port on the back of the unit and will carry the exhaust gases to the outside of the house. This exhaust liner must be directly connected to the unit and run the full length of the chimney.

IMPORTANT NOTICE:

THE USE OF AN EXISTING CHIMNEY AS AN AIR INTAKE IS NOT COVERED UNDER THE ANSI Z21.88-1999-CSA2.33M99 TEST METHODS AND RESULTING ITS/WHI PRODUCT CERTIFICATION. THE CODE AUTHORITY HAVING JURISDICTION MUST BE CONSULTED PRIOR TO PROCEEDING WITH THIS INSTALLATION METHOD.

The other 3” liner will be attached to the intake port on the back of the unit and will provide fresh air for combustion to the unit. This liner must extend a minimum of 6’ off the back of the unit and extend through the damper area of the fireplace and into the first section of pipe. This liner can also extend the full length of the chimney and connect to the termination cap. See figure 10.

IMPORTANT:

If the intake flex does not extend the full length of the chimney and connect to the unit and the termination cap - THEN A METAL BLOCK OFF PLATE MUST BE CONSTRUCTED AND INSTALLED ABOVE THE UNIT PRIOR TO THE END OF THE INTAKE FLEX (normally at the damper area).

To avoid cross venting the insertalways label the flex to be used for the exhaust conduit at both the top and bottom ends of the flex. This ensures that the exhaust flex is installed to the proper outlet on the chimney termination kit.

The minimum vent height above the roof or adjacent walls is specified by major building codes. A general guide to follow is the Gas Vent Rule below.

GAS VENT RULE

 

 

 

Minimum Height

 

 

 

ROOF SLOPE

 

From Roof

 

 

 

Flat to 6/12

 

1’0”

 

0.3M

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Over 7/12 to 9/12

 

2’0”

 

0.6M

 

 

 

 

 

 

 

 

 

 

 

 

Over 10/12 to 12/12

 

4’0”

 

1.2M

 

 

 

 

 

 

 

 

 

 

 

 

Over 13/12 to 16/12

 

6’0”

 

1.8M

 

 

 

 

 

 

 

 

 

 

 

 

Over 17/12 to 21/12

 

8’0”

 

2.4M

 

 

 

 

 

 

 

 

 

 

CANADA REQUIREMENT: Both the Intake and the Exhaust liners must extend the full length of the chimney and be securely connected to both the unit and the termination kit.

If the fireplace has been modified to accommodate installation, use anchors or masonry nails to attach the metal Fireplace Conversion Notice Plate supplied with this unit to the back wall of the masonry fireplace firebox where it will be readily seen should the insert be removed.

12

Listed Direct Vent

Termination Cap

Venting InstallationThrough a

PrefabricatedFireplace

 

 

123456789012

 

 

 

 

12345678901

2

 

 

 

123456789012

 

1. Measure height of the chimney to fireplace

 

 

234

 

234

 

 

234

 

234

opening. Determine if both the intake and

 

 

234

 

234

 

 

234

 

234

exhaust will be extended to the top of the

 

 

234

 

234

 

 

234

 

234

 

 

 

234

 

234

chimney.

 

 

234

 

234

 

 

234

 

234

 

Factory-builtListed

234

 

234

2. Cut the appropriate lengths of flex for both the

234

 

234

Gas Chimney

 

234

 

234

intake and exhaust.

 

234

 

234

 

 

234

 

234

 

 

 

234

 

234

3. Attach the appropriate ends of the flex to the

 

 

234

 

234

 

 

234

 

234

chimney termination kit.

 

 

234

 

234

 

 

234

 

234

 

 

 

234

PIPE

234

4. Drop the liners down the chimney from the top

 

 

234

234

 

 

234

 

234

and rest the termination kit atop the chimney.

 

 

234

 

234

 

 

234

FLEX

234

 

 

 

234

234

 

 

 

234

 

234

5. Seal the chimney termination kit to the top of the

 

 

234

INTAKE

234

 

 

234

234

chimney pipe with high temperature sealant.

 

 

234

 

234

 

 

234

 

234

 

 

 

234

 

234

6. Secure the appropriate DIRECT VENT CAP to the

 

 

234

AIR

234

 

 

234

234

termination kit.

Listed Flexible

 

234

234

 

234

 

234

 

 

 

234

 

234

7. Inside the fireplace, fully extend the flex and cut

Gas Liners

 

234

 

234

 

234

PIPE

234

off the excess flex so that the liners hang ap-

Max. Height 35 ft.

 

234

234

 

 

234

234

 

Min. Height 10ft.

 

234

234

proximately 15” from the floor of the fireplace.

 

234

FLEX

234

 

 

234

234

8. If the intake flex is not attached to the chimney

 

 

234

 

234

 

 

 

234

EXHAUST

234

 

 

 

234

234

 

 

 

234

 

234

termination kit: See NOTICE on page 12.

 

 

234

 

234

 

 

234

 

234

A. It is now necessary to install a minimum of a 6

 

 

234

 

234

 

 

234

 

234

 

 

234

 

234

foot length of flex into the flue for the intake air.

INTAKE FLEX MUST

 

234

 

234

 

 

234

 

234

B. A METAL damper block off plate must be

EXTEND A MINIMUM

 

234

 

234

 

234

 

234

constructed and installed in the damper area to

OF 6’ AND INTO

 

234

 

234

THE CHIMNEY PIPE

 

234

 

234

completely seal off the flue from the room.

 

234

 

234

 

 

234

 

234

 

 

 

234

 

234

Remember to cut holes for both the intake and

 

 

234

 

234

Maintain proper

 

234

 

234

exhaust liners in the block off plate.

 

234

 

234

clearance to Mantel

 

234

 

234

 

 

234

 

234

C. A direct vent cap is still required to allow fresh

and Trim

 

 

23456234

 

234

 

23456234

 

234

air into the chimney flue and ultimately into the

 

23456234

 

234

Metal block-offplate is

23456234

 

234

intake flex and insert.

23456234

 

234

required to seal flue

23456234

 

234

D. Attach the Fireplace Conversion Notice to the

23456234

 

234

 

23456234

 

234

 

from the living area if

23456234

 

234

back of the fireplace if appropriate.

Air Intake pipe does not

23456234

 

234

23456234

 

234

 

connect directly to a

23456

 

 

 

9. Compress the liners so that they are hanging

23456

 

 

 

Direct Vent Termination

23456

 

 

 

above the height of the fireplace opening and are

at the top of the

23456

 

 

 

chimney

23456

 

 

 

out of the way.

23456

 

 

 

 

To Exhaust

 

 

10. Position the insert without surround panels

Attach Fireplace

Collar

 

 

half-wayinside the fireplace and attach the liners

 

 

 

 

to the appropriate ports on the rear of the stove.

Conversion Notice

 

 

 

 

Be sure not to cross vent the insert.

Plate to Rear Wall

 

 

To Air

 

of Fireplaceif the

 

 

Intake

 

11. Secure the liners to the ports using sheet metal

damper has been

 

 

Collar

 

modified.

 

 

 

 

screws or hose clamps. No silicone or sealant is

 

 

 

 

 

 

 

 

 

 

required.

 

1234567890123456789012

 

 

123456789012345678901

2

 

123456789012345678901

2

 

1234567890123456789012

 

Figure 8. Factory-builtFireplace Vent Configuration.

 

13

Connecting the Gas Supply

Gas Supply Requirements

ALL INSTALLATIONS MUST COMPLY WITH LOCAL

CODE OR IN THE ABSENCE OF LOCAL CODE, MUST

COMPLY WITH THE MOST RECENT EDITION OF THE NATIONAL FUEL GAS CODE ANSI Z223.1/NFPA 54 OR

CAN-B149.

NOTE: INSTALL THE OPTIONAL BLOWER BEFORE PLUMBING THE GAS LINE TO THE VALVE.

THIS PRODUCT MUST BE INSTALLED BY A LICENSED MASTER OR JOURNEYMAN PLUMBER OR GAS-FITTERWHEN INSTALLED IN THE COMMONWEALTH OF MASSACHUSETTS.

Shutoff Valve

All codes require a gas shutoff valve (gas cock) and union to be installed in the supply line and in the same room as the appliance. This allows for the disconnection of the fireplace for servicing and maintenance. See Fig. 9.

A T-HANDLEGAS SHUTOFF VALVE IS REQUIRED IN MASSACHUSETTS IN COMPLIANCE WITH CODE 248CMR.

The fireplace and gas control valve must be disconnected from the gas supply piping during any pressure testing of the system at test pressures in excess of 1/2 psig. For pressures lower than 1/2 psig, isolate the gas supply by closing the manual shutoff valve.

Control Valve Connection

The gas supply line connection is made to the left side of the valve. The gas supply line should be a minimum 3/8" diameter, or the appropriate size to provide sufficient gas pressure to the valve regardless of the input setting.

The use of flexible gas appliance connectors is acceptable in many areas in the U.S. In Canada, methods vary depending on local code. If local codes permit, use flexible gas line for ease of installation and service. For those locales where flexible gas lines are not permitted, use the 3/8” iron fitting to make the connection at the left side of the Control Valve. See Figures 9 and 10.

Secure all joints tightly using appropriate tools and sealing compounds (for propane units, be sure to use compounds that are propane resistant). Turn on gas supply and test for gas leaks using a soapy water solution. Never use an open flame to check for leaks.

Leak test:

Mix a 50-50solution of water and dish soap.

Light appliancesee lighting instructions on page 23 of this manual or on the fireplace’s rating plate.

Brush or spray all joints and connections with the soapy water solution.

If bubbles appear at any connection or seam or a gas odor is detected, immediately turn gas control knob to the OFF position.

Tighten or reconnect the leaking joint and retest for any gas leaks.

Figure 9. Gas supply line fittings.

Gas Pressure

Proper gas pressure provides a consistent flow of gas to the appliance and is instrumental in checking for gas leaks. The gas control valve on the fireplace is equipped with pressure test points for gauge connections. The gauge connections are located on the front of the valve under the On/Off/ Pilot knob. Gauge connections are identified by:

IN/E forinlet or supply pressure (the amount of gas coming to the valve.)

OUT/A formanifold pressure (the amount of gas that is coming out of the valve to the burner.)

E A

Figure 10. Pressure test point as located on the front of the valve.

14

The appliance must be isolated from the gas supply line by closing its individual manual gas shutoff valve (gas cock) during any pressure testing of the gas supply piping system that is equal to or exceeds pressures of 1/2 psig (3.5 kPa).

 

Inlet Pressure

 

MIN

MAX

Natural Gas:

5.0 WC (1.24 kPa)

7.0 WC (1.74 kPa)

Propane: 12.0 WC (2.98 kPa)

13.0 WC (3.23 kPa)

 

Manifold Pressure

 

MIN

MAX

Natural Gas:

1.2 WC (0.29 kPa)

3.8 WC (.95 kPa)

Propane:

2.9 WC (0.72 kPa)

11.0 WC (2.74 kPa)

 

 

 

ALWAYS TEST PRESSURE WITH VALVE CONTROL KNOB SET ON HIGH. Symptoms of incorrect gas pressure include:

Insufficient gas pressure:

Small pilot flame which can result in insufficient millivolts.

Little variation in flame picture between HI and LO settings.

Insufficient gas to support more than one appliance causing nuisance outages or gas surges.

Excessive gas pressure:

Permanent damage to valve causing complete appliance shut down.

Too large a pilot flame resulting in overheating of the power generator and consequent shut down.

Sooting due to impingement and/or incorrect fuel to air mix.

High Altitude Adjustment

Installations located at altitudes from 2000 - 4250 ft. (610 M - 1370 M), DONOT require adjustment. Do not derate this appliance for altitude.

15

Fuel Conversion

The GI425 Fireplace is designed to for use with either Natural gas or Propane. It is shipped from the factory configured to use Natural gas. A conversion kit is included for conversion to Propane use if desired. Check the identification label on the Control Valve to confirm that the correct fuel is used.

WARNING:

THE CONVERSION KIT IS TO BE INSTALLED BY AN AUTHORIZED JØTUL SERVICE TECHNICIAN IN ACCORDANCE WITH THE MANUFACTURER’S INSTRUCTION AND ALL CODES AND REQUIREMENTS OF THE AUTHORITY HAVING JURISDICTION. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE. THE QUALIFIED AGENCY PERFORMING THIS WORK ASSUMES RESPONSIBILITY FOR THIS CONVERSION.

IN CANADA:

THE CONVERSION SHALL BE CARRIED OUT IN ACCORDANCE WITH THE REQUIREMENTS OF THE PROVINCIAL AUTHORITIES HAVING JURISDICTION AND IN ACCORDANCE WITH THE REQUIREMENTS OF THE CAN1-B149.1AND .2 INSTALLATION CODE.

Cet equipement de conversion sera installe par une agence qualifiee de service conformement aux instructions du fabricant et toutes exigences et codes applicables de l’autorises avoir la juridiction. Si l’information dans cette Instruction n’est pas suivie exactement, un fey, explosion ou production de protoxyde de carbone peut resulter blessure personnelle de vie. L’agence qualifiee de service est esponsable de l’installation n’est pas propre et complete jusqu’a l’operation de l’appareil converti est cheque suivant les criteres etablis dans les instructions de proprietaire provisionnees avec l’equipement.

Tools required:

1/4” Nut driver, 7/16” and 1/2” open end wrench or deep well socket, 4 mm allen wrench, Torx t20 or slotted screwdriver.

Conversion Kit Contents:

#155300 - LP #155303 - NG

1 Regulator Tower labeled for Propane

3 Regulator Tower Screws

1 Burner Orifice (3/32” NG,

1.45 mm LP)

1 Pilot Orifice (#30 for LP,

#51 for NG)

Label A - to be completed and applied to the control valve.

Label B - apply to the fireplace Rating Plate as designated on the plate.

WARNING: If appropriate, be sure to unplug the blower before proceeding with this conversion.

Fuel Conversion Procedure

1. Remove the Glass Frame:

Release the two frame latches and lift the frame up off of the retainer tabs at the top of the firebox.

2. Empty the firebox:

Lift and remove the Fettle and Logset package. CAUTION: THE LOGS ARE FRAGILE. Handle them with care and set aside out of the way.

Remove the Logset Base by lifting it out of the firebox.

3. Change the Burner Orifice:

Loosen the locknut on the Air Shutter Stem, located under the firebox floor to the right of the Control Valve. This will allow you to disengage the Burner Tube. Fig. 11.

Lift the rear of the Burner Tube and rotate slightly forward. Slide the tube to the left enough to disengage it from the Air Shutter and

Burner Orifice, then lift out. Slide the Air Shutter back out of the way to expose the orifice. Fig. 12.

Using a ½” open end wrench or deep well socket remove the burner orifice and replace with the appropriate orifice, supplied in the kit.

4.Change the Pilot Orifice:

FROM WITHIN THE FIREBOX, disengage the Pilot Hood by releasing the retainer clip as shown in Fig. 13. Using a 4 mm allen wrench, unscrew the pilot orifice (counter clockwise). Replace with the appropriate orifice:

#51 for Natural gas #30 for Propane

16

Tighten new orifice into the base of the pilot assembly.

• Replace Pilot Hood by pushing it into the base.

5.Replace the Burner Tube:. Slip the end of the tube into the Air Shutter and SLIDE TUBE TO THE RIGHT TO COMPLETELY COVER THE

Pull Frame Spring

Air Shutter Latch to release.

Wingnut

OPEN

CLOSED

Figure 11. Frame latch and air shutter stem location.

Injector

Air Shutter

Burner Orifice

Stem

Figure 12. Burner orifice removal and replacement.

Pilot Hood

Pilot Orifice

Retainer Clip

PILOT ASSEMBLY

Figure 13. Pilot Orifice replacement.

ORIFICE.

6. Adjust the Air Shutter: See Fig. 31.

• Slide the shutter forward (toward yourself) to open the inlet. Slide it back to the rear to close.

The standard settings are: Natural gas - 1/4” open Propane - 1/2” open

7.Change the Regulator: See Fig. 14.

Using a Torx T-20screwdriver or small flat head screwdriver, remove the three specialty screws from the front of the valve regulator.

Remove the regulator tower and gasket.

BE SURE TO REMOVE THE BLACK RUBBER GASKET FROM THE VALVE.

Install the new variable regulator tower with the new rubber gasket. Thoroughly tighten new regulator to valve body.

8.Apply the Conversion Labels:

Apply LABEL A to the cabinet floor so that it may be seen by anyone servicing the fireplace.

Apply LABEL B to the Rating Plate in the space provided.

9.Reassemble the fireplace, apply gas to the system and check for gas leaks including all gas lines before and after the valve. NEVER USE AN OPEN FLAME TO CHECK FOR GAS LEAKS.

IMPORTANT: Correct gas pressure is essential for efficient and safe operation. It is important that the correct gas pressure be established at the time of the installation. For more details, see the Gas Pressure section of this manual on page 14.

WHEN LIGHTING THIS APPLIANCE, ALWAYS REFER TO THE LIGHTING INSTRUCTIONS ON THE BACK COVER OF THIS MANUAL.

BE SURE TO

REMOVE THE

BLACK

RUBBER

GASKET

FROM THE

VALVE.

Figure 14

Valve Regulator replacement.

17

Wall Thermostat Installation

Use Jøtul Thermostat #129706 or a 750 millivolt DC two-wire circuit thermostat to automatically control your fireplace operation. The thermostat should be placed in the same room as the heater, typically 5’ off the floor. Avoid drafty areas or any area that may affect the accuracy of the thermostat.

The thermostat should be connected to the GI425 using a minimum of 16 gauge wire with a maximum length of 35 feet of wire.

Connect the two thermostat wire leads to the two lower terminals on the terminal block located to the right of the ON/OFF/T’STAT switch. Do not overtighten the connections. IT IS NOT NECESSARY TO DISCONNECT ANY OTHER WIRES. See Figure 16.

At the thermostat, the two wires should be connected to the two connections screw on the thermostat base plate per the manufacturer’s instructions.

For thermostatic function, place the ON/OFF/T-STATswitch in theT-STATposition and the pilot flame must be lit.

THERMOPILE

ROCKER

 

SWITCH

 

ON

TH

OFF

TP

STAT

 

TH

 

TP

 

VALVE

OPTIONAL

THERMOSTAT

 

or

 

REMOTE

 

CONTROL

TERMINAL

BLOCK

Figure 16. GI425 Valve Wiring Diagram

Remote Control

The optional Jøtul Remote Control can be installed on the GI425 gas fireplace. Using the wire supplied with the remote, connect the remote directly to the gas control valve.

Connect one receiver lead to the terminal labelled TH. Connect the other receiver lead to the terminal labeled TH/TP. DO NOT DISCONNECT ANY OTHER WIRES FROM THE VALVE, AND DO NOT OVER TIGHTEN THE TERMINAL SCREWS.

Place the receiver unit under the control valve on the floor of the fireplace cabinet.

CAUTION:

LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING THE CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERATION. ALWAYS VERIFY PROPER OPERATION AFTER SERVICING THE APPLIANCE.

ATTENTION:

AU MOMENT DE L’ENTRETIENDES COMMANDES, ETIQUETEZ TOUS LES FILS AVANT LE DEBRANCHEMENT. DES ERREURS DE CABLAGE PEUVENT ENTRAIUN FONCTIONNEMENT INADEQUAT ET DAGEREUX.

18

Brick Panel Assembly

CAUTION: THESE PANELS ARE EXTREMELY FRAGILE! SUPPORT EACH PIECE WITH BOTH HANDS AND HANDLE TENDERLY.

Install the optional Brick Panel Kit 155311 before placing the Logset. Place the panels in position in the order as numbered in Fig. 17. No fasteners or tools are required.

Upper Rear Panel,

220515

4

3 1

Lower Rear Panel, 220514

Left Side Panel, 220516

Figure 17. Panel installation order.

2

Right Side Panel, 220517

1.Remove the Glass Frame, if you have not already done so. Remove the Ashlip and locate the two frame latches under the firebox floor. See Fig. 18. Pull the latch handles forward to disengage them from the bottom of the glass frame. You can then pull the frame out and up off of the three retainer tabs at the top of the firebox opening. Set the Glass Frame out of the way.

2.Remove the Fettle and Logset. These parts are not fastened. Simply lift them out of the firebox.

3.Install the Lower Rear Panel. Orient the panel so that the cutout is at the bottom. Engage the bottom edge between the rear wall and the firebox base. See Fig. 17.

4.Install the Side Panels. Engage the bottom edge of each side panel between the Logset Base and the firebox wall and push the panel forward against the front lip of the firebox opening. See Fig.20.

5.Install the Upper Rear Panel. This will also be a snug fit. Set the panel up high and then carefully lower it to seat its lower edge against the top of the other rear panel. The side panels will hold it in place.

6.Install the Logset (see pg. 20).

7.Replace the Fettle, Andirons and Glass Assembly.

Pull Frame Latches to

Release Frame

Figure 18. Glass Frame latch locations.

Logset Base

Figure 19. Install Lower Rear Panel.

Side

Panel

Figure 20. Install the Side Panel.

19

Logset Assembly

This is the heart of your Jøtul GI 425 Camden fireplace. Much time and effort has been devoted to attaining a lively, realistic flame picture while simultaneously achieving efficient fuel combustion and effective heat output under a variety of installation conditions. The flame picture you experience, however, will be affected by a number of variables peculiar to your installation such as venting configuration, environmental and weather conditions, and fuel type. Log placement is critical to the final flame picture. Pay particular attention to placing the log pieces as illustrated here. Carefully unpack and arrange the logs as outlined below. CAUTION: The logs are fragile. Please handle each piece with care.

Use safety gloves to handle the log parts as the ceramic fibers can irritate skin.

1.Place the Rear Log in position on Ceramic Base pegs as shown in fig. 22. The base is already installed in the fireplace.

2.Set the Right, Left, and Center Logs on the appropriate pegs as shown in fig. 23.

3.Lightly scatter the Platinum Ember material (included in the Miscellaneous Hardware Bag) over the forward area of the Logset Base. Place them directly on top of the burner base and around the log parts. With a little experimentation, you will find that they add an inviting, glowing ember effect after the burner has been operating for a few minutes.

4.Replace the Glass Panel Frame: Engage the top of the frame with the three tabs at the top of the firebox. Push the bottom of the frame against the firebox face and pull the Frame

Latches out to engage them with the slots in the bottom of the frame.

Center Log

Right Log

Left Log

Rear Log

Ceramic Base

Figure 21. Logset Parts.

Figure 22. Engage Rear Log with Base pegs.

Loosely scatter Ember material over the burner screen and around the front log pieces.

Figure 23. Install the Center, Left and Right Logs on the pegs.

20