JL Audio Stealthbox SB-T-TUNCNSL2-10W3v2 User Manual

Size:
517.21 Kb
Download

Stealthbox®

I N S T A L L A T I O N G U I D E for the

SB-T-TUNCNSL2/10W3v2

(‘03-UpToyota Tundra Access & Double Cab with front bucket seats and center console)

This Stealthbox is a product which requires professional installation skills and tools.

Please read this installation guide thoroughly before beginning the project. It will guide you step by step through the installation. Several of the steps in this process may require two people to accomplish.

It is absolutely vital that the enclosure be properly mounted to the vehicle according to these instructions. Failure to mount the enclosure properly presents two problems: 1) The sub-bassperformance will suffer due to the movement of the enclosure caused by the force exerted by the woofer(s) and 2) A loose enclosure presents a serious safety hazard in the event of a collision or sudden deceleration.

Please enjoy your JL Audio Stealthbox responsibly.

START

HERE

 

 

 

STEP 1: Using a 14mm socket, remove the

STEP 2: Tilt the seat to the rear, unplug the

four bolts that secure the passenger side front

exposed wire assembly, remove the seat from

seat.

the truck.

STEP 3: Remove the front storage access door. Using a 10mm socket, remove the exposed bolts.

 

 

 

 

STEP 4: With the main storage door open,

STEP 5: Using a 10mm socket, remove the

STEP 6: Remove the plastic buttons that are

grab ahold of the black cup holder section

exposed bolts. Also remove the bolts that are

located on each side of the center console.

and pull up.

located at the bottom of the main storage

 

 

bucket.

 

Continued on Next Page

w w w . j l a u d i o . c o m

SB - T- TUNCNSL2/10W3v2, JL AUDIO, Inc 2005

Pag e 1

Sheet SKU#011180 Revision 4/6/2005

Cont.

From

Previous

Page

 

 

 

 

STEP 7: Slide the center console to the rear of truck.This will allow exposer of the 12v plug wires. Unplug and then remove the center console from truck.

*Tundra Access Cab Only*

Keep the air ducts inside the truck, for now.

STEP 8: *Tundra Access Cab Only*

With the center console out of the truck, flip up side down. Remove the two air duct ears that are located to the rear of the center console.

STEP 9: Remove the 8 screws that is securing the black plastic support to the outer console. Not all circles represent all 8 screws.

There are a pair of screws on each side of the console that need to be removed.

3/4”

Driver’s side

middle

Passenger’s side

STEP 10: *Tundra Access Cab Only*

Now it is time to remove those air ducts from STEP 7. With the ducts removed, you will need to cut both ducts. Place the ducts so the front of the ducts are facing to the right.

Driver’s side: Measure and mark 3/4” from front of foam tape, back. Cut at location.

Passenger’s side: Cut at the middle of the foam tape.

 

 

4-3/4”

 

6-1/2”

 

 

 

1-3/4”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

STEP 11: Back inside the truck. Remove the black bracket that is mounted to the floor of the truck(not pictured).

*Tundra Access Cab Only*

Using a 1/2” drill bit and drill. Enlarging the mounting holes from the bracket.

*Tundra Access Cab Only*

STEP 12: Cut 1-1/2” off of each carpet flap, that is located in front of the mounting holes, from

STEP10.

*Tundra Access Cab Only*

STEP 13(a): Place only one of the supplied wax squares into this location.

Place the middle of the supplied wax square, 4-3/4”back from the front consoles metal mounting bracket.

*Tundra Double Cab Only*

STEP 13(b)

FRONT WAX SQUARE

Place the middle of one of the supplied wax squares, 4-3/4”back from the front consoles metal mounting bracket.

REAR WAX SQUARES

Place the middle of the remaining pair of supplied wax squares, 1-3/4”back from the center console rear mounting holes.

Continued on Next Page

w w w . j l a u d i o . c o m

SB - T- TUNCNSL2/10W3v2, JL AUDIO, Inc 2005

Pag e 2

Sheet SKU#011180 Revision 4/6/2005

Cont.

From

Previous

Page

STEP 14: Thread in the three supplied socket cup set screws into the Stealthbox. Make sure that the socket ends are on the outside of the Stealthbox.

The rear(left side of pic) threaded rods need to protrude about 1 1/4” out of the Stealthbox.The front socket cup set screw needs to protrude about 3/4”.

Place the Stealthbox into location. Slide the rear socket cup set screw through the drilled out holes from STEP10. Press firmly on the front of the Stealthbox, marking the wax square.

STEP 16(a): *Tundra Access Cab Only*

Remove the Stealthbox.You should have an impression on the wax square.

*CAUTION*

Before drilling, make sure that you are not going to be drilling into any gas lines, brake lines, transmission lines, electrical wiring, transfer case(4x4 vehicles) or anything else that might cause a reduction in your weekly pay. Always wear eye protection when drilling.

With the use of a 1/2” drill bit and drill. Drill out the floor at the impression on the wax square

STEP 15: Place the Stealthbox into position, Press down firmly.

STEP 16(b): *Tundra Double Cab Only*

Remove the Stealthbox.You should have an impression on the wax square.

*CAUTION*

Before drilling, make sure that you are not going to be drilling into any gas lines, brake lines, transmission lines, electrical wiring, transfer case(4x4 vehicles) or anything else that might cause a reduction in your weekly pay. Always wear eye protection when drilling.

With the use of a 1/2” drill bit and drill. Drill out the floor at the impression on the wax square

Continued on Next Page

w w w . j l a u d i o . c o m

SB - T- TUNCNSL2/10W3v2, JL AUDIO, Inc 2005

Pag e 3

Sheet SKU#011180 Revision 4/6/2005

Cont.

From

Previous

Page

STEP 17: Remove the wax square and run speaker wire.

STEP 18: *Access Cabs Only*

Replace the modified A/C ducts from STEP 10, back into the vehicle.

(Stealthbox is only shown in the picture for position purposes.You do not have to have the Stealthbox in location to accomplish this step)

STEP 19: With the Stealthbox and the modified A/C ducts in position. Place the front section of the center console back into the proper location. Do not secure at this time.

*Remember to plug in the 12v sockets.*

(Stealthbox is only shown in the picture for position purposes.You do not have to have the Stealthbox in location to accomplish this step)

STEP 20: Place the Stealthbox into the center console, outside of vehicle .

*Double Cabs Only*

The permanent removal of the rear seat 12v plug is neded.

THREADED INSERT

 

STEALTHBOX WALL

 

 

 

VEHICLE SHEET METAL

 

FENDER WASHER

 

SOCKET CUP SET SCREW

 

FLAT WASHER

 

LOCK WASHER

 

HEX NUT

STEP 21: Place the Stealthbox/center console into vehicle. Attach the speaker wire to terminal.

Back out the three socket cup screws to 1-1/4:”.

STEP 22: Place Stealthbox/center console upright and into the proper position. Carefully guiding the threaded rods through the three drilled holes.

Pop in the four supplied black plastic push rivets, into the screw holes on each side of the center console.

w w w . j l a u d i o . c o m

SB - T- TUNCNSL2/10W3v2, JL AUDIO, Inc 2005

Pag e 4

 

 

 

STEP 23: Apply a supplied flat washer, lock washer and nut onto the three socket sup set screw. Tightly secure all three nuts. .

Continued on Next Page

Sheet SKU#011180 Revision 4/6/2005

Cont.

From

Previous

Page

 

 

 

CONGRATULATIONS!

INSTALL COMPLETE.

STEP 24: With the Stealthbox securely mounted

STEP 25: Secure the front section of console with

Included Hardware:

3) Wax Squares

to the vehicle. Secure the plastic console to the

the factory screws, from STEP 3.

3) 3/8”-1-1/4”Fender Washer

floor, using the factory screws from STEP 5.

Once both portions of the center console have

3) 3/8” Flat Washer

 

 

been secured. Snap in the cup holders from

 

3) 3/8” Split Lock Washer

 

STEP 4, front console storage door fromSTEP 3

 

3) 3/8”-16x2-1/4”Socket Cup Set Screw

 

and the plastic buttons from STEP 6.

 

3) 3/8”-16Hex Nut

 

 

 

 

Difficulty Of Installation:

Specifications:

Enclosure Type: Sealed

Driver Type: 10W3v2-D2

Nominal Impedance: 4Ω

Cont. Power Handling: 300Watts

JL Audio recommends using a high quality amplifier such as the JL Audio 250/1. The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 250/1 when being used to power your Stealthbox®.

+12VDC Ground Remote

Preamp Output Section

Bass Control

Amp LP Filter

Amplifier Input Section

 

Output Mode

Infrasonic Filter

Mode/Slope

Input Voltage

Input Sens. Signal Sensing

 

Full-Range/Low-Pass/High-Pass

 

Off/30Hz

Off/12dB/24dB

Low/High

Off/On

 

 

 

 

+7

 

 

 

 

 

 

+3

+10

 

 

 

JL AUDIO 250/1

 

 

+1

+13

 

 

 

 

 

 

 

 

 

 

monoblock subwoofer amplifier

 

 

 

 

 

 

 

 

Left Ch.

Right Ch.

LF Boost (dB)

Filter Freq. (Hz)

Left Ch.

Right Ch.

The JL Audio 250/1 is a very versatile audio component. Please consult the owner’s manual for detailed information about installing and tuning this amplifier.

Mid/High Frequency Driver Information:

Front Location Driver Size:

6.5”

Applicable JL Audio Products:

VR650-CSi

TR,VR, XR, ZR 650-CSi

mounting plates are needed

Rear Location Driver Size:

6.5”

Applicable JL Audio Products:

TR,VR,XR 650-CXimounting plates are needed

VR650-CXi

 

10369 N. Commerce Pkwy, Miramar, Florida 33025-392

Phone: 954.443.1100 Fax: 954.443.1111

w w w . j l a u d i o . c o m

SB - T- TUNCNSL2/10W3v2, JL AUDIO, Inc 2005

Pag e 5

Sheet SKU#011180 Revision 4/6/2005