JL Audio Stealthbox SB-T-TTNCRW-10W3v2 User Manual

Size:
487.14 Kb
Download

Stealthbox®

I N S T A L L A T I O N G U I D E for the

SB-N-TTNCRW/210W3v2

(04-UpNissan Titan Crew Cab)

This Stealthbox is a product which requires professional installation skills and tools.

Please read this installation guide thoroughly before beginning the project. It will guide you step by step through the installation. Several of the steps in this process may require two people to accomplish.

It is absolutely vital that the enclosure be properly mounted to the vehicle according to these instructions. Failure to mount the enclosure properly presents two problems: 1) The sub-bassperformance will suffer due to the movement of the enclosure caused by the force exerted by the woofer(s) and 2) A loose enclosure presents a serious safety hazard in the event of a collision or sudden deceleration.

Please enjoy your JL Audio Stealthbox responsibly.

START

HERE

STEP 1: The wax square needs to be placed into the curvature of the floor bulk head.

STEP 2: With the passenger side rear seat lifted, out of the way.

Measure 8” from the left floor corner to the middle of the placed wax square.

Once placement is found, remove the paper backing and adhere to the carpet.

STEP 3: Place the supplied socket cup set screw into the enclosure, leaving 1/4” exposed.

 

STEP 5:

*CAUTION*

 

 

Before drilling, make sure that you are not going to

 

 

be drilling into any gas lines, brake lines, transmission

 

lines, electrical wiring, transfer case(4x4 vehicles) or

anything else that might cause a reduction in your

weekly pay. Always wear eye protection when drilling.

With the use of a 1/2” drill bit and drill. Drill out the floor at the impression on the wax square.

STEP 4: Place the enclosure into position and press down firmly.

Make sure that the enclosure does not move around when placing the enclosure into position.

Once the wax square is marked, remove the enclosure out of vehicle.

STEP 6: With the enclosure removed out of the vehicle, expose1-1/2”of the socket cup set screw.

Continued on Next Page

w w w . j l a u d i o . c o m

SB - N - TTCRW/10W3v2, JL AUDIO, Inc 2004

Pag e 1

Sheet SKU#01192 Revision 10/9/2004

Cont.

From

Previous

Page

THREADED INSERT

STEALTHBOX WALL

 

 

 

CONGRATULATIONS!

 

 

 

INSTALL COMPLETE.

 

 

VEHICLE SHEET METAL

 

 

 

FENDER WASHER

 

 

 

SOCKET CUP SET SCREW

 

 

 

FLAT WASHER

 

 

 

LOCK WASHER

 

 

 

HEX NUT

 

STEP 7: Run and attach speaker wire from the

STEP 8: With the socket cup set screws protrud-

amplifier location to the enclosure.

ing through the floor of the vehicle. Place the sup-

 

plied fender washer, flat washer, lock washer and hex

 

nut in this order.

 

Secure tightly.

Included Hardware:

1) Wax Square

1) 3/8” x2-1/4”Fender Washer

1) 3/8” Flat Washer

1) 3/8” Split Lock Washer

1) 3/8”-16Hex Nut

1) 3/8”-16x2-1/4”Socket Cup Screw

Difficulty Of Installation:

Specifications:

Enclosure Type: Sealed

Driver Type: 2) 10W3v2-D4

Nominal Impedance: 4Ω

Cont. Power Handling: 600Watts

JL Audio recommends using a high quality amplifier such as the JL Audio 500/1. The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 500/1 when being used to power your Stealthbox®.

Preamp Output Section

Infrasonic Filter

"Q"

Center Freq.

Boost (dB)

Amp LP Filter

Amplifier Input Section

Subwoofer Output

Output Mode

Filter Slope

 

1.6

 

45

 

+10

Mode / Slope

Input Voltage Input Sens. Signal Sensing

 

 

 

1.1

2.7

35

55

+4

+13

 

 

 

0.7

25

70

Full Range / Amp Filter / Out Filter

12dB / 24dB

 

Off / 30Hz

0.5

4.3

20

85

0

+15

Off / 12dB / 24dB

Low / High

Off / On

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+12VDC Ground Remote

 

65

 

Filter Mode

 

30

Bass EQ

 

 

 

 

 

65

 

+

+

_

_

 

55

85

 

25

40

 

 

Advanced

55

85

 

 

 

45

120

 

18

50

 

 

 

 

45

120

 

 

 

JL AUDIO 500/1

 

 

 

 

 

 

 

 

 

 

Bass

 

 

 

 

 

 

 

 

 

40

200

LP / HP

15

60

Off / On

 

 

Control

40

200

 

MONO OUTPUT ONLY

five-channelsystem amplifier

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Left Ch.

Right Ch.

Filter Freq. (Hz)

 

Infrasonic Freq. (Hz)

 

 

Remote Bass Port

 

 

Filter Freq. (Hz)

Left Ch.

Right Ch.

 

 

 

The JL Audio 500/1 is a very versatile audio component. Please consult the owner’s manual for detailed information about installing and tuning this amplifier.

Mid/High Frequency Driver Information:

Dash Location Driver Size:

2.5”

VR075-CT

Applicable JL Audio Products:

 

TR050-CT,VR075-CT,XR100-CT

 

*mounting plate is needed

 

Front Location Driver Size:

 

6” x 9”

 

Applicable JL Audio Products:

VR690-CXi

TR690-TXi,VR690-CXi

 

*mounting plate is needed

 

Rear Location Driver Size:

 

6.5” separates

 

Applicable JL Audio Products:

VR650-CSi

TR,VR, XR, ZR 650-CSi

*mounting plate is needed

 

 

10369 N. Commerce Pkwy, Miramar, Florida 33025-392

Phone: 954.443.1100 Fax: 954.443.1111

w w w . j l a u d i o . c o m

SB - T- TTNCRW/10W3v2, JL AUDIO, Inc 2004

Pag e 2

Sheet SKU#01192 Revision 10/9/2004