JL Audio Stealthbox SB-H-CRV-10W3v3-GA User Manual

Size:
332.98 Kb
Download

I n s t a l l a t i o n G u i d e for the

SB-H-CRV/10W3V3

SKU#94429

2007+

Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With proper installation, your newvehicle-specificenclosed subwoofer system will deliver years of listening pleasure.

We strongly recommend that you have your new Stealthbox® installed by your authorized JL Audio dealer. The installation professionals employed by your dealer have the necessary tools and experience to disassemble and reassemble your vehicle properly. If you prefer to perform your own installation, please read this installation guide completely

before beginning the process.

SB-H-CRV/10W3V3INSTR_SKU#011281

If you choose to perform the installation yourself, it is absolutely vital that the Stealthbox® be properly mounted to the vehicle according to these instructions. Failure to mount the enclosure properly presents two problems:

1)The sub-bassperformance will suffer due to the movement of the enclosure caused by the force exerted by the woofer(s).

2)A loose enclosure presents a serious safety hazard in the event of a collision or sudden deceleration.

INSTALLATION D I F F I C U LT Y :

3OUT OF

5

Estimated TIME:

2-3HOURS

S T E P 1

Remove any contents in the trunk of the car so that you will have a clean area to work in. Place the Wax Square as shown

S T E P 2

Thread the included Hex Head Bolt into the enclosure so that approximately 1/2” remains exposed (as shown).

S T E P 3

Set the Stealthbox in place. Push in and, down as indicated by the arrows to get the bolt to make an impression in the wax square.

Continued on Next Page

S T E P 4

Remove the enclosure, ensure that an adequate depression has been made in the Wax Square to use it as a guide to drill a hole. If the impression is not present, back the bolt out of the enclosure and, repeat STEP 3 untill there is a well defined impression in the Wax Square.

S T E P 5

Using a 1 inch hole saw, drill and cut a hole through the inner plastic panel. At the same time, drill the pilot hole only

through the metal inner fender panel.

*CAUTION*

Before drilling, always make sure that you are not going to be drilling into any gas lines, brake lines, transmission lines, electrical wiring, exhaust systems or anything else that might cause a reduction in your weekly pay. Always wear eye protection when drilling.

S T E P 6

From inside the fender well, insert the Hex Head Bolt, Split Lock Washer and Fender Washer through the hole drilled in

STEP 5

S T E P 7

From inside the vehicle, the Hex Head Bolt should protrude well past the interior plastic trim panel.

SB-H-CRV/10W3V3INSTR_SKU# 011281

S T E P 8

Insert the Spacer over the Hex Head Bolt, through the 1” hole in the interior plastic trim panel so that it will rest against the metal interior fender panel.

STEALTHBOX WALL

THREADED INSERT

PLASTIC INTERIOR PANEL

PLASTIC INTERIOR PANEL

 

SPACER

 

VEHICLE SHEET METAL

FLAT WASHER

HEX HEAD BOLT

LOCK WASHER

 

S T E P 9

This illustration details how the hardware should be arranged to mount the Stealthbox® securely.

S T E P 1 0

Hook up the wire from the amplifier to the Stealthbox®, and test the Stealthbox® to ensure the correct operation. Have a friend slide the Stealthbox®into postion while you turn the Hex Head Bolt in order to get the threads started into the Stealthbox®, tighten the fastners.

S T E P 1 1

C O N G R A T U L A T I O N S !

You have completed the installation for this model!

Enjoy your new Stealthbox®!

Please refer to the Power Recommendation section for an amplifier recommendation and basic set-uphelp.

Page 2 • JL Audio, Inc 2008

Continued on Next Page

 

 

 

SB-H-CRV/10W3V3INSTR_SKU# 011281

I N C L U D E D H A R D W A R E

 

 

 

1)

3/8” Split Lock Washer

1)

3/8” x 1 1/4” Fender Washer

1)

3/8-16x 2 1/2” Hex Head Bolt

1)

3/8”(ID) x 1”Steel Spacer

S P E C I F I C A T I O N S

Enclosure Type: Acoustic Suspension (sealed)

Driver Type: 10W3v3-4

Nominal Impedance: 4 Ohms

Continuous Power Handling: 500 Watts

P o w e r R e c o m m e n d a t i o n

JL Audio recommends using a high quality amplifier such as the JL Audio 250/1v2.

The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 250/1v2 when being used to power your Stealthbox®.

The JL Audio 250/1v2 is a very versatile audio component. Please consult the owner’s manual for even more detailed information about installing and tuning this amplifier.

M I D / H I G H F r e q u e n c y D r i v e r F I T M E N T

A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.

Front Speaker Size / Location: 6 1/2”- Front Doors

Fits JL Audio Models: TR650-CXi,TR650-CSi,VR650-CXi,VR650-CSi,C5-650,C5-650x&ZR650-CSi

Rear Speaker Size / Location: 6 1/2”- Rear Door

Fits JL Audio Models: TR650-CXi,TR650-CSi,VR650-CXi,VR650-CSi,C5-650,C5-650x&ZR650-CSi

(954) 443-1100

 

www.jlaudio.com

 

 

 

All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered

 

 

 

 

trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.

 

 

 

 

JLA-SKU#011281©11-13-2008• Printed in USA • ©2008 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902

 

 

 

 

#6,243,479 #6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign

 

 

 

 

patents pending. For more detailed information please visit us online at www.jlaudio.com.

 

 

 

 

 

 

1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y

M I R A M A R , F L O R I D A

3 3 0 2 5

U S A

Page 5• JL Audio, Inc 2008