JL Audio Stealthbox SB-GM-SLVCTR2-10W3v3-GA2 User Manual

Size:
269.23 Kb
Download

I N S T A L L A T I O N G U I D E for the

SB-GM-SLVCTR2/10W3v3

2007 - Up Silverado, Sierra, Avalanche, Suburban, Tahoe, Yukon & Yukon XL with Front Row 40/20/40 Split Bench Seating

Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With proper installation, your newvehicle-specificenclosed subwoofer system will deliver years of listening pleasure.

We strongly recommend that you have your new Stealthbox® installed by your authorized JL Audio dealer. The installation professionals employed by your dealer have the necessary tools and experience to disassemble and reassemble your vehicle properly. Also, keep in mind that your warranty coverage extends to 2 years if your system is installed or approved by your authorized JL Audio dealer. If you prefer to perform your own installation, please read this installation guide completely

before beginning the process.

SB-GM-SLVCTR2/10W3v3_INSTR_SKU#011248

If you choose to perform the installation yourself, it is absolutely vital that the Stealthbox® be properly mounted to the vehicle according to these instructions. Failure to mount the enclosure properly presents two problems:

1)The sub-bassperformance will suffer due to the movement of the enclosure caused by the force exerted by the woofer(s).

2)A loose enclosure presents a serious safety hazard in the event of a collision or sudden deceleration.

INSTALLATION D I F F I C U LT Y :

2OUT

5OF

ESTIMATED TIME:

1-2HOURS

S T E P 1

Remove any contents from the front seat area.

Flip the center seat back / storage bin in the up position.

S T E P 2

Move both front seats all the way forward.

From the passenger side of the vehicle, look to the side of the center seat back / storage bin.

Remove the black plastic push clip.

Remove the plastic trim.

S T E P 3

From the driver’s side of the vehicle, look to the side of the center seat back / storage bin.

Remove the bolt and plastic trim.

Continued on Next Page

S T E P 4

From the driver’s side of the vehicle, look to the side of the center seat back / storage bin.

Use an hex key to remove the black bolt that secures the gray bracket to the center seat back / storage bin.

S T E P 5

From the passenger’s side of the vehicle, look to the side of the center seat back / storage bin.

Use an hex key to remove the black bolt that secures the gray bracket to the center seat back / storage bin.

S T E P 6

Grab a hold of the bottom cushion and pull forward. Remove the bottom cushion from the vehicle.

S T E P 7

Remove the plastic tray from vehicle.

SB-GM-SLVCTR2/10W3v3_INSTR_SKU#011248

S T E P 8

Remove the four rear bolts that secure the seating to the floor.

S T E P 9

Remove the four front nuts that secure the seating to the floor.

S T E P 1 0

Run speaker wire from the amplifier location to the Stealthbox® location.

S T E P 1 1

Slide the rear of the Stealthbox® into the mounting area first, then drop the front of the Stealthbox® into place.

Page 2 • JL Audio, Inc 2007

Continued on Next Page

S T E P 1 2

Place the supplied lock washer and then flat washer onto the supplied bolt.

Tilt the seating back.

From under the center seat section, place the bolt assembly through a factory hole and into the threaded insert of the Stealthbox®. This hole can be viewed in STEP 7, circled.

Secure the bolt assembly to the Stealthbox®, do not over tighten.

S T E P 1 3

We do not recommend the use of this center section to be used as a seat. You can remove the seat belt latch as an extra precaution.

S T E P 1 4

Secure the bolts and nuts that were removed in

STEPs 8 & 9.

Secure the plastic covers that were removed in STEPs 2 & 3.

C O N G R A T U L A T I O N S

You have completed the installation for this model!

Please refer to the Power Recommendation section for an amplifier recommendation and basic set-uphelp.

SB-GM-SLVCTR2/10W3v3_INSTR_SKU#011248

I N C L U D E D H A R D W A R E

(1) 3/8-inch-16x1-1/4-inchHex Bolt

(1) 3/8-inchLock Washer

(1) 3/8-inchFlat Washer

S P E C I F I C A T I O N S

Enclosure Type: Acoustic Suspension (sealed)

Driver Type: 10W3v3

Nominal Impedance: 4 ohms mono

Continuous Power Handling: 300 Watts

P O W E R R E C O M M E N D A T I O N

JL Audio recommends using a high quality amplifier such as the JL Audio 250/1v2.

The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 250/1v2 when being used to power your Stealthbox®.

The JL Audio 250/1v2 is a very versatile audio component. Please consult the owner’s manual for even more detailed information about installing and tuning this amplifier.

M I D / H I G H F R E Q U E N C Y D R I V E R F I T M E N T

A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.

Front Speaker Size / Location: 6.5-inch /Front Doors

Fits JL Audio Models: TR650-CSi,TR650-CXi,VR650-CSi,VR650-CXi,XR650-CSi,XR650-CXi,C5650,C5-650x&ZR650-CSi

Rear Speaker Size / Location: 5.25-inch /Rear Door

Fits JL Audio Models: TR525-CXi,VR525-CSi,VR525-CXi,C5-525,C5-525x&ZR525-CSi

(954) 443-1100

www.jlaudio.com

 

 

All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.

JLA-SKU#011248-09-06-2007 • Printed in USA • ©2007 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902 #6,243,479 #6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending. For more detailed information please visit us online atwww.jlaudio.com.

Page 3 • JL Audio, Inc 2007

1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A