JL Audio Stealthbox SB-F-TRKCTR3-10W3v3 User Manual

Size:
300.05 Kb
Download

Stealthbox®

I N S T A L L A T I O N G U I D E

for the

SB-F-TRKCTR3/10W3

(Fits 2001-UpStandard Cab,Super-CabandSuper-Crewtrucks

lso fits, 2001 Harley Davidson and King Ranck trucks)

This Stealthbox is a product which requires professional installation skills and tools. Please read this installation guide thoroughly before beginning the project. It will guide you step by

step through the installation. Several of the steps in this process may require two people to accomplish.

It is absolutely vital that the enclosure be properly mounted to the vehicle according to these instructions. Failure to mount the enclosure properly presents two problems: 1) The sub-bassperformance will suffer due to the movement of the enclosure caused by the force exerted by the woofer(s) and 2) A loose enclosure presents a serious safety hazard in the event of a collision or sudden deceleration.

Please enjoy your JL Audio Stealthbox responsibly.

START

HERE

STEP 1: Remove the front cup holder to reveal two 18mm bolts. Remove these bolts.

STEP 4: Remove (unsnap) the rear panel of the console.

STEP 2: Remove tray and liner to reveal two 18mm bolts. Remove these bolts. Remove console from truck.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

STEP 5: Remove the armrest lid of the console by removing four Phillips head screws.

STEP 6: Remove the 7mm bolt that is exposed when console top is removed.

STEP 3: Cut and remove the carpet under the console as shown in the picture.

**WARNING**

Seat Belt sensor wire runs underneath this carpet. DO NOT CUT THIS WIRE!

STEP 7: Remove three 7mm bolts denoted by the arrows in the picture.

Continued on Page 2

Cont.

From

age 1

 

 

4

1

 

 

Bottom

Rib

2

3

 

STEP 8: Remove the four screws (two per side) from the sides of the console.

STEP 9: A large section of the bottom of the console must be removed. The cut travels from side to side 3/4” in front of the bolt at the rear the bottom of the console (point #1). This cut then angles down to meet the edge of the bottom rib on the side of the enclosure (point #2). The cut travels to the other end of the rib(point #3) and then angles up the side and across the bottom so as to meet a point 1/2” inside the bolt at the front of the bottom of the console (point #4). The same path is taken on the other side of the console.

STEP 10: Remove the nine remaining 7mm bolts to separate the inner console.

STEP 11: Sandwich the Stealthbox between the two halves of the inner console and secure using the nine 7mm bolts removed in step 10.

STEP 12: Glue the two supplied 8”x8” pieces of carpet to the sides of the inner console (one per side).

 

 

 

 

 

 

 

 

 

 

 

 

STEP 13: Reinstall the outside console over the inner console and the Stealthbox with eight 7mm bolts which were removed in steps 6,7 and 8. Place the conlose/Stealthbox back into the truck.

STEP 14: Run speaker wire so that it is accessible at the front of the enclosure, connect it to the enclosure and test for proper operation.

STEP 15: Using an an 18mm socket wrench, secure the front of the console to the vehicle with the 18mm bolts removed in Step 1.

STEP 16: Using an an 18mm open end wrench, secure the rear of the console to the vehicle with the 18mm bolts removed in Step 4.

STEP 17: Snap rear panel (removed in step 4) back unto rear of console.

STEP 18: Reinstall cup holders (removed in Step1).

Continued on Page 3

Cont. From Page 2

CONGRATULATIONS!

INSTALL COMPLETE.

 

Included Hardware:

 

(1)

Replacement Tray

 

(2)

8”x8” Carpet Pieces

STEP 19: Reinstall console top (removed in

Estimated Installation Duration:

Step 5) and place supplied tray into console.

Specifications:

Enclosure Type: Acoustic Suspension (Sealed)

Driver Type: One JL AUDIO10W3-D6Subwoofer

Nominal Impedance: 3Ω

Cont. Power Handling: 250 Watts

JL Audio recommends using a high quality amplifier such as the JL Audio 250/1. The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 250/1 when being used to power the the F-150Stealthbox®.

Ground Remote

Preamp Output Section

Bass Control

Amp LP Filter

Amplifier Input Section

 

Output Mode

Infrasonic Filter

Mode/Slope

Input Voltage

Input Sens. Signal Sensing

 

Full-Range/Low-Pass/High-Pass

Off/30Hz

Off/12dB/24dB

Low/High

Off/On

 

+3

+7

55

65

 

 

 

+10

85

 

 

AUDIO 250/1

+1

+13 45

120

 

 

 

 

 

 

 

 

monoblock subwoofer amplifier

0

+15

40

200

 

 

Left Ch.

Right Ch.

LF Boost (dB) Filter Freq. (Hz)

Left Ch.

Right Ch.

Subwoofer Output

MONO OUTPUT ONLY

The JL Audio 250/1 is a very versatile audio component. Please consult the owner’s manual for detailed information about installing and tuning this amplifier.

Mid/High Frequency Driver Information:

Front Location Driver Size:

XR570-CSi

5"x7” (1271mm x 177.8mm)

Applicable JL Audio Products:

TR570-CXi,XR570-CXior CSi

Rear Location Driver Size:

5"x7” (1271mm x 177.8mm)

Applicable JL Audio Products:

XR570-CXi

TR570-CXi,XR570-CXior CSi

10369 N. Commerce Pkwy, Miramar, Florida 33025-392

Phone: 954.443.1100 Fax: 954.443.1111