JL Audio C2-600x-06112008 User Manual

Size:
381.38 Kb
Download

owner’s manual

6.0-inch(150 mm) Coaxial Loudspeakers

Thank you for choosing a JL Audio Evolution™ C2 Coaxial Speaker System for your automotive sound system.

These Evolution™ Speakers have been designed and manufactured to exacting standards in order to ensure years of musical enjoyment in your vehicle. For maximum performance, we highly recommend that you have your new speakers installed by an authorized JL Audio dealer. Your authorized dealer has the training, expertise and installation equipment to ensure optimum performance from this product. Should you

decide to install the speakers yourself, please take the time to read this manual thoroughly so as to familiarize yourself with its installation requirements and setup procedures.

If you have any questions regarding the instructions in this manual or any aspect of your amplifier’s operation, please contact your authorized JL Audio dealer for assistance. If you need further assistance,

please call the JL Audio Technical Support Department at (954) 443-1150during business hours.

 

 

 

B

 

 

D

E

 

 

 

F

A

 

G

 

 

 

 

 

 

C

Woofer Physical Dimensions

Frame Outer Diameter (A)

6.21 in. / 157.7 mm

Grille Tray Outer Diameter (B)

6.51 in. / 165.3 mm

Magnet Outer Diameter (C)

3.15 in. / 80.0 mm w/o cover

Frontal Tweeter Protrusion (D)

0.55 in. / 13.9 mm

Frontal Grille Protrusion (E)

0.91 in. / 23 mm

Mounting Hole Diameter (F)

5.00 in. / 127.0 mm

Mounting Depth (G)

2.38 in. / 60.3 mm w/o cover

Due to ongoing product development, all specifications are subject to change without notice.

2 | JL Audio - C2-600xOwner’s Manual

C2-600xSpecifications:

Woofer: Injection-molded,Mica-filled,Polypropylene Cone, Butyl Rubber Surround, 1 in. Voice Coil on Kapton® Former, Flat, Symmetrical Roll Spider, Ferrite Magnet

Tweeter: 0.75 in. (19 mm) Silk Dome, Ferrofluid Cooling / Damping, Neodymium Magnet

Crossover: Natural Roll-OffLow-Pass,1st OrderHigh-PassFilter with Electrolytic Capacitor

Continuous Power Handling: 60 Watts

Recommended Amp Power: 15-100Watts per channel (RMS) Efficiency: 90.5 dB @ 1W/1m | 96.5 dB @ 1W/0.5m Sensitivity: 93.5 dB @ 2.83V/1m

Nominal Impedance: 4 ohm

Frequency Response: 59 Hz - 22 KHz ± 3 dB

Included Components and Parts:

Two C2-600x6.0-inch(150mm) Coaxial loudspeakers

Two Grille Assemblies

Eight #8 x 1 1/4-inch(30mm) sheet metal screws

Eight Mounting Clips

Two 5.2 mm female crimpable connectors

Two 2.8 mm female crimpable connectors

Two self-adhesiveJL Audio logo name badges

GETTING STARTED

• Turn off the audio system. It is also advisable to disconnect the negative (–)terminal of your vehicle’s battery whenever performing installation work.

• Before cutting, drilling or inserting any screw, check clearances on both sides of the planned mounting surface. Also check for any potential obstacles, such as window tracks and motors, wiring harnesses, etc. Check both sides of the

vehicle, many vehicles are not symmetrical!

• Always wear protective eyewear.

SPEAKER PLACEMENT CONSIDERATIONS

In most cases, your speakers will be placed into factory speaker locations. If you have some speaker mounting flexibility, keep the following in mind:

Lower mounting locations, such as the lower front corner of a door or a kick-panelprovide the greatest path length distances for the sound emitted by the speakers. For this reason, they are generally more desirable than higher mounting locations. Higher mounting locations will usually result in extremenear-sidesoundstage bias which compromises the stereo listening experience.

3

SPEAKER INSTALLATION

The speaker should be installed in one of the following ways depending on location:

Factory Location: If you will be using the factory speaker wires, it may be necessary to change the terminations. This may be accomplished by using an adaptor plug or simply by cutting the factory connector off and using the supplied crimp connectors to terminate the speaker wires. The large connector is for the positive terminal and the small connector is for the negative terminal of eachC2-600x.

You may also choose to run new speaker wires...

Run speaker wire to the desired mounting locations. If you are running wires into a door, use existing factory wiring boots whenever possible. If you are drilling new holes, file their edges and install rubber grommets into each hole. Wires should then be covered with a protective, flexible PVC sleeve and then run through the door jamb. Make sure that the wires will clear door hinges and other structures in the door. If you are unsure about any part of this process, please contact your JL Audio dealer for installation help.

!! WARNING

Double check the clearance for both speakers before proceeding. Many cars are different from one side to the other!

Your new speakers have been designed to install, without modifications, into most vehicles that accept a 6-inch(150 mm) speaker. Most factory6-inchspeakers use four mounting screws which will line up with the mounting holes on yourC2-600xspeakers. Others use a3-holemounting system which is accommodated by a separate set of mounting holes on the frames of yourC2-600xspeakers.

It is absolutely vital that the speaker frame fits into the mounting hole cleanly. This must be checked prior to tightening the screws. Do not force the frame into a hole that is too small. Do not tighten the speaker onto an uneven surface. This will damage your speakers. The speaker should also fit so that air does not leak around the mounting flange. Air leaks will cause a severe degradation in sound quality. Seal any air leaks with an automotive-gradesealant material.

Install as shown in Diagram A (page 5). Use the supplied mounting clips unless the factory holes already feature threaded inserts. Hand-tightenthe screws evenly to avoid bending the speaker frame!

Custom Location: Run speaker wire to the desired mounting location. If you are running wires into a door, use existing factory wiring boots whenever possible. If you are drilling new holes, file their edges and install rubber grommets into each hole. Then, cover the wires with a protective PVC sleeve and run them through the door jamb. Make sure that the wires will clear door hinges and other structures in the door. If you are unsure about any part of this process, please contact your JL AUDIO dealer for installation help.

!! WARNING

Double check the clearance for both speakers before proceeding. Many cars are different from one side to the other!

Select an even surface. Tightening a speaker onto an uneven surface can damage it. Use the supplied template to mark the desired mounting location.

Mark the center and the outline of the mounting hole as well as the mounting screw positions. Before drilling or cutting on your interior panels, use a utility knife to cut any fabric, vinyl or leather from hole locations. These materials can easily be snagged by a drill or a saw, causing damage to the panel and possible bodily injury. Drill four 1/8-inch(3 mm) holes for the speaker’s mounting screws at the positions you have marked. Also drill a pilot hole in the center of the speaker mounting hole at this time. Then, using a saber saw, make the circular cut out for the speaker. File any rough edges. Insert the

mounting clips with the flat side towards the speaker as shown in Diagram B (page 5).

It is absolutely vital that the speaker frame fits into the mounting hole cleanly. This must be checked prior to tightening the screws. Do not force the frame into a hole that is too small. Do not tighten the speaker onto an uneven surface. This will damage your speakers.

The speaker should also fit so that air does not leak around the mounting flange. Air leaks will cause a severe degradation in sound quality. Seal any air leaks with an automotive-gradesealant material.

4 | JL Audio - C2-600xOwner’s Manual

Connect the speaker wires, observing correct

!!

WARNING

 

Hand-tightenthe screws evenly in acriss-cross

polarity, and install the speaker and grille assembly

as shown in Diagram B (below). Hand-tightenthe

pattern to avoid bending the speaker frame or

screws evenly to avoid bending the speaker frame!

stripping the mounting clips.

The included JL Audio logo name badges should

 

 

 

be affixed to the circular indented area in the lower

 

 

 

part of each grille assembly. If the grille assembly is

 

 

 

not used, the JL Audio logo badges can be affixed

 

 

 

elsewhere as creative additions to your installation.

 

 

 

Diagram A:

Factory Location Woofer Installation

Diagram B:

Custom Location Woofer Installation

5

NOTES

6 | JL Audio - C2-600xOwner’s Manual

NOTES

7

Limited Warranty - Automotive Speaker Systems (USA)

JL AUDIO warrants these speakers (and crossover networks, where applicable) to be free of defects in materials and workmanship for a period of one (1) year.

This warranty is not transferable and applies only to the original purchaser from an authorized

JL AUDIO dealer. Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction, JL AUDIO will (at its discretion), repair or replace the defective product with new or remanufactured product at no charge. Damage caused by the following is not covered under warranty: accident, misuse, abuse, product modification or neglect, failure to follow installation instructions, unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential damages and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear is not covered under warranty.

Any applicable implied warranties are limited in duration to the period of the express warranty as provided herein beginning with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to this product thereafter. Some states do not allow limitations on implied warranties, therefore these exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

If you need service on your JL AUDIO product:

All warranty returns should be sent to JL AUDIO freight prepaid through an authorized JL AUDIO dealer and must be accompanied by proof of purchase (a copy of the original sales receipt.) Direct returns from consumers or non-authorizeddealers will be refused unless specifically authorized by JL AUDIO with a valid return authorization number. Warranty expiration on products returned without proof of purchase will be determined from the manufacturing date code. Coverage may be invalidated as this date is previous to purchase date. Return only defective components. If one speaker fails in a system, return only that speaker component, not the entire system.Non-defectiveitems received will be returnedfreight-collect.Customer is responsible for shipping charges and insurance in sending the product to JL AUDIO. Freight damage on returns is not covered under warranty.

For Service Information in the U.S.A. please call JL Audio Customer Service: (954) 443-1100 9:00 AM – 5:30 PM (Eastern Time Zone)

JL Audio, Inc

10369 North Commerce Pkwy.

Miramar, FL 33025

International Warranties:

Products purchased outside the United States of America are covered only by that country’s distributor and not by JL Audio, Inc.

C2-600x-06112008